LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Snap-ins, 105℃ KMV Series ・For frequently change of regenerative voltage from AC servo amplifier and inverter control ・Ideal use to power supply, specially power source with turn on and off frequently and highly voltage fluctuation ・Improved the resistance for charge and discharge from same dimension of KMQ series ・Endurance with ripple current : 3,000 hours at 105℃ ・Rated voltage range : 350 to 450Vdc, Capacitance 82 to 1,200µF ・Non solvent resistant type ・RoHS Compliant ◆SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Leakage Current Dissipation Factor (tanδ) Low Temperature Characteristics (Max. Impedance Ratio) Charge and Discharge -25 to +105℃ 350 to 450Vdc ±20% (M) I≦3 CV Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) Rated voltage (Vdc) 350 & 400V 420 & 450V tanδ (Max.) 0.15 0.20 Rated voltage (Vdc) 350 to 450V Z(-25℃)/Z(+20℃) 8 (at 20℃, 120Hz) (at 20℃ after 5 minutes) (at 20℃, 120Hz) (at 120Hz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to charge and discharge test with the voltage waveform shown below at room temperature (15 to 35℃). ≦±20% of the initial value Capacitance change ≦200% of the initial specified value D.F. (tanδ) ≦The initial specified value Leakage current Frequency Number of cycles 6Hz 50 million times Rated voltage ≦150V Voltage waveform 1 cycle 0V Endurance The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated ripple current is applied (the peak voltage shall not exceed the rated voltage) for 3,000 hours at 105℃. Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦200% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4. Capacitance change ≦±15% of the initial value D.F. (tanδ) ≦150% of the initial specified value Leakage current ≦The initial specified value Shelf Life *Please consult with us about charge and discharge conditions. ◆DIMENSIONS [mm] Code : VS (φ22 to φ35) : Standard Sleeve (PET : Brown) Negative mark ●Terminal Code : LI (φ35) Sleeve (PET : Brown) PC board pin-out Negative mark φD+1max. φD+1max. 10 Vent 2-φ2 L±2.5 PC board pin-out 2-1.2×6 4.2±0.5 ●Terminal 4.0±0.5 Vent 5±0.5 L±2.5 4.5±1 14.2±1 No plastic disk is the standard design. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 259 CAT. No. E1001N LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Snap-ins, 105℃ KMVSeries ◆PART NUMBERING SYSTEM 1 2 3 4 E KMV 5 6 7 8 9 10 VS N 11 12 13 14 M 15 16 17 18 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 270µF:271, 1,200µF:122) Dummy terminal code Terminal code (VS, LI) Voltage code (ex. 350V:351, 400V:401) Series code Category Please refer to "Product code guide (snap-in type)" ◆STANDARD RATINGS WV Cap (Vdc) (µF) 350 400 120 150 180 220 220 220 270 270 270 330 330 330 330 390 390 470 470 470 560 560 680 680 820 820 1,200 100 120 150 180 180 180 220 220 220 270 270 270 270 330 330 390 390 390 470 470 560 560 680 820 1,000 Rated ripple Max. charge current and Case size current Max.discharge φD×L(mm) (Arms/ current 105℃,120Hz) (Arms/ 6Hz) 22×25 22×30 25.4×25 22×35 22×40 25.4×30 22×45 25.4×35 30×25 22×50 25.4×40 30×30 35×25 25.4×45 30×35 25.4×50 30×40 35×30 30×45 35×35 30×50 35×40 35×45 35×50 35×60 22×25 22×30 25.4×25 22×35 22×40 25.4×30 22×45 25.4×35 30×25 22×50 25.4×40 30×30 35×25 25.4×45 30×35 25.4×50 30×40 35×30 30×45 35×35 30×50 35×40 35×45 35×50 35×60 0.74 0.87 0.92 1.08 1.10 1.05 1.24 1.21 1.15 1.41 1.37 1.29 1.31 1.51 1.44 1.69 1.62 1.61 1.82 1.77 2.04 2.02 2.27 2.32 2.88 0.69 0.79 0.87 0.99 1.01 0.98 1.14 1.13 1.10 1.30 1.28 1.22 1.26 1.44 1.38 1.59 1.55 1.55 1.74 1.71 1.93 1.94 2.19 2.45 2.79 0.42 0.49 0.54 0.60 0.62 0.61 0.71 0.70 0.68 0.80 0.80 0.77 0.78 0.89 0.88 0.99 1.00 0.97 1.12 1.08 1.27 1.25 1.41 1.46 1.84 0.38 0.44 0.49 0.55 0.56 0.55 0.64 0.63 0.61 0.73 0.72 0.70 0.71 0.82 0.81 0.91 0.91 0.89 1.03 1.00 1.15 1.14 1.29 1.44 1.70 Part No. EKMV351VSN121MP25S EKMV351VSN151MP30S EKMV351VSN181MQ25S EKMV351VSN221MP35S EKMV351VSN221MP40S EKMV351VSN221MQ30S EKMV351VSN271MP45S EKMV351VSN271MQ35S EKMV351VSN271MR25S EKMV351VSN331MP50S EKMV351VSN331MQ40S EKMV351VSN331MR30S EKMV351VSN331MA25S EKMV351VSN391MQ45S EKMV351VSN391MR35S EKMV351VSN471MQ50S EKMV351VSN471MR40S EKMV351VSN471MA30S EKMV351VSN561MR45S EKMV351VSN561MA35S EKMV351VSN681MR50S EKMV351VSN681MA40S EKMV351VSN821MA45S EKMV351VSN821MA50S EKMV351VSN122MA60S EKMV401VSN101MP25S EKMV401VSN121MP30S EKMV401VSN151MQ25S EKMV401VSN181MP35S EKMV401VSN181MP40S EKMV401VSN181MQ30S EKMV401VSN221MP45S EKMV401VSN221MQ35S EKMV401VSN221MR25S EKMV401VSN271MP50S EKMV401VSN271MQ40S EKMV401VSN271MR30S EKMV401VSN271MA25S EKMV401VSN331MQ45S EKMV401VSN331MR35S EKMV401VSN391MQ50S EKMV401VSN391MR40S EKMV401VSN391MA30S EKMV401VSN471MR45S EKMV401VSN471MA35S EKMV401VSN561MR50S EKMV401VSN561MA40S EKMV401VSN681MA45S EKMV401VSN821MA50S EKMV401VSN102MA60S WV Cap (Vdc) (µF) 420 450 82 120 120 150 150 180 180 180 180 220 220 220 270 270 270 330 330 330 390 390 470 470 560 680 820 82 100 100 120 150 150 150 180 180 180 220 220 220 220 270 270 270 330 330 330 390 390 470 560 680 Rated ripple Max. charge current and Case size current Max.discharge φD×L(mm) (Arms/ current 105℃,120Hz) (Arms/ 6Hz) 22×25 22×30 25.4×25 22×35 25.4×30 22×40 22×45 25.4×35 30×25 22×50 25.4×40 30×30 25.4×45 30×35 35×25 25.4×50 30×40 35×30 30×45 35×35 30×50 35×40 35×45 35×50 35×60 22×25 22×30 25.4×25 22×35 22×40 25.4×30 30×25 22×45 22×50 25.4×35 25.4×40 25.4×45 30×30 35×25 25.4×50 30×35 35×30 30×40 30×45 35×35 30×50 35×40 35×45 35×50 35×60 0.64 0.81 0.81 0.93 0.93 1.04 1.06 1.06 1.02 1.20 1.20 1.14 1.36 1.29 1.26 1.52 1.47 1.42 1.64 1.56 1.83 1.78 1.98 2.23 2.52 0.64 0.72 0.72 0.81 0.93 0.91 0.90 1.03 1.06 1.04 1.18 1.20 1.10 1.12 1.35 1.25 1.27 1.42 1.46 1.41 1.61 1.59 1.79 2.00 2.26 0.34 0.44 0.44 0.50 0.50 0.56 0.58 0.58 0.56 0.66 0.65 0.63 0.74 0.73 0.71 0.83 0.84 0.82 0.94 0.91 1.06 1.05 1.18 1.34 1.55 0.34 0.40 0.40 0.45 0.51 0.50 0.51 0.58 0.59 0.57 0.65 0.67 0.63 0.64 0.75 0.73 0.74 0.84 0.87 0.84 0.97 0.96 1.08 1.22 1.42 Part No. EKMV421VSN820MP25S EKMV421VSN121MP30S EKMV421VSN121MQ25S EKMV421VSN151MP35S EKMV421VSN151MQ30S EKMV421VSN181MP40S EKMV421VSN181MP45S EKMV421VSN181MQ35S EKMV421VSN181MR25S EKMV421VSN221MP50S EKMV421VSN221MQ40S EKMV421VSN221MR30S EKMV421VSN271MQ45S EKMV421VSN271MR35S EKMV421VSN271MA25S EKMV421VSN331MQ50S EKMV421VSN331MR40S EKMV421VSN331MA30S EKMV421VSN391MR45S EKMV421VSN391MA35S EKMV421VSN471MR50S EKMV421VSN471MA40S EKMV421VSN561MA45S EKMV421VSN681MA50S EKMV421VSN821MA60S EKMV451VSN820MP25S EKMV451VSN101MP30S EKMV451VSN101MQ25S EKMV451VSN121MP35S EKMV451VSN151MP40S EKMV451VSN151MQ30S EKMV451VSN151MR25S EKMV451VSN181MP45S EKMV451VSN181MP50S EKMV451VSN181MQ35S EKMV451VSN221MQ40S EKMV451VSN221MQ45S EKMV451VSN221MR30S EKMV451VSN221MA25S EKMV451VSN271MQ50S EKMV451VSN271MR35S EKMV451VSN271MA30S EKMV451VSN331MR40S EKMV451VSN331MR45S EKMV451VSN331MA35S EKMV451VSN391MR50S EKMV451VSN391MA40S EKMV451VSN471MA45S EKMV451VSN561MA50S EKMV451VSN681MA60S Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 260 CAT. No. E1001N LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Snap-ins, 105℃ KMVSeries ◆RATED RIPPLE CURRENT MULTIPLIERS ●Frequency Multipliers Frequency(Hz) 50 120 300 1k 10k 50k Coefficient 0.77 1.00 1.16 1.30 1.41 1.43 The endurance of capacitors is shorted with internal heating produced by ripple current at the rate of halving the lifetime with every 5℃ rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 261 CAT. No. E1001N