Startup Manual Specifications Packing List Before you begin installing your board, please make sure that the following materials have been shipped: Standard SBC Functions • 1 startup manual • CPU: Embedded NS GXM-233 processor (PCM-5820/5820L) Embedded NS GXM-200 processor (PCM-5820E/5822) • 1 utility disk/CD driver, and manual (in PDF format) • BIOS: AWARD 256 KB Flash memory • 1 2.5" IDE flat cable, 44-pin to 44-pin (part no. 1701440351) • System memory: One 144-pin SODIMM socket accepts up to 128 MB SDRAM • 1 keyboard / PS2 mouse cable (part no. 1700060201) • 1 secondary serial port cable (part no. 1701140201) • Enhanced IDE interface: Supports up to two EIDE devices. BIOS auto-detect, PIO Mode 3 or Mode 4 transfer, Ultra DMA33 mode (ATA-4) up to 33 MB/sec • 1 parallel cable (part no. 1700260250) • FDD interface: Supports up to two FDDs • 1 floppy cable, for 3.5" FDD only (part no. 1701340602) • Serial ports: One serial RS-232 port, one serial RS-232/422/485 port • 1 PCM-5820 Series all-in-one single board computer • 1 audio cable (part no. 1700160160) • Parallel port: One parallel port, supports SPP/EPP/ECP mode • 1 USB cable (part no. 1703100260) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Note 1: Note 2: • Infrared port: Shared with COM2. Transfer rate up to 115 kbps For detailed contents of the PCM-5820 Series please refer to the enclosed CD-ROM or disk (in PDF format). • Keyboard/mouse connector: Mini-DIN connector supports standard PC/AT keyboard and PS/2 mouse Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: www.adobe.com/Prodindex/acrobat/ readstep.html (Acrobat is a trademark of Adobe.) • Power management: Supports power saving modes including Normal/Standby/Suspend. APM 1.1 compliant • USB interface: Two USB ports, USB 1.0 compliant • Watchdog timer: 1.6 sec. intervals Local-bus Flat Panel/VGA Interface • Chipset: NS CX5530 • Display memory: 1 ~ 4 MB share memory, set in BIOS • Display type: Supports CRT and TFT LCDs. Able to display both CRT and flat panel simultaneously For more information on this and other Advantech products, please visit our website at: • CRT display mode: Non-interlaced CRT monitor resolutions up to 1280 x 1024 @ 256 colors or 1024 x 768 @ 16 bpp http://www.advantech.com http://www.advantech.com/epc For technical support and service, please visit our support website at: http://support.advantech.com This manual is for the PCM-5820L Rev. A103 or higher, the PCM-5820E Rev. A101 or higher, or the PCM-5822 Rev. A101. Part No. 2006582005 Printed in Taiwan • Flat-panel display mode: Panel resolution supports up to 1024 x 768 @ 16 bpp. Supports 18-bit TFT LCD panel LVDS (Low Voltage Differential Signal) Interface (PCM-5820, PCM-5820L, PCM-5820E only) • Chipset: TI SN75LVDS84 or compatible chipset PCM-5820 Series Pentium® SBC with CPU, VGA/LCD, Ethernet & Audio PCM-5820 Series Pentium® SBC with CPU, VGA/LCD, Ethernet & Audio Interface • Performance: 18 low-voltage TTL data channels ANSI/EIA/TIA-644 3rd Edition Dec. 1999 PCM-5820 Series Startup Manual 1 TV-out (PCM-5822 only) • Chipset: CHRONTEL CH7003C • Supports NTSC, NTSC-EIA (Japan) and PAL TV formats • Provides Composite, S-video, and SCART (optional) outputs via RCA (composite) connector and S-video connector • Supports 640 x 480 and 800 x 600 input resolutions • Supports Windows 95/98 and Windows NT driver • Over-scan, under-scan, and position adjustable • Auto-detection of TV presence Audio Function • Chipset: NS CX5530 • Audio controller: AC97 version 2.0 compliant interface • Audio interface: Microphone in, Line in, CD audio in, Line out, Speaker L, Speaker R • Power: Accepts +12 V source for improved audio quality Ethernet Interface (PCM-5820/5820E/5822 only) • Chipset: RTL 8139 • Ethernet interface: PCI 10/100 Mbps Ethernet. IEEE 802.3 U protocol compatible • Connection: On-board RJ-45 connector • I/O address switchless setting • Built-in boot ROM Solid State Disk • Supports one 50-pin socket for CompactFlash™ card J3 J4 J5 J6 J7 Watchdog timer action COM2 setting Buzzer setting LCD power selector Ethernet power select (PCM-5822) Table 2-2: Connectors Label CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 CN18 CN19 CN20 CN21 CN22 CN23 CN24 LED1 LED2 SW1 Function CD audio input connector Floppy disk connector Parallel port connector USB connector Audio connector CPU fan power connector (5820/L/E) IR connector (infrared) PC/104 connector Main power connector (+5 V, +12 V) Auxilary power connector (-5 V, -12 V) IDE hard disk connector LCD connector Ethernet connector COM2 connector LVDS connector (5820/L/E) COM1 connector PS/2 keyboard + PS/2 mouse CRT display connector CompactFlash socket SODIMM socket RCA composite connector (PCM-5822 only) S-Video connector (PCM-5822 only) ATX feature connector (PCM-5822) ATX power button & power LED connector Ethernet LED (PCM-5820/E,PCM-5822) Power & HDD LED (PCM-5820/L/E Reset button (PCM-5820/L/E) Mechanical and Environmental • Dimensions (L x W): 145 mm x 102 mm (5.9" x 4.2") Locating Jumpers • Power supply voltage: +5 V (4.75 V ~ 5.25 V) • Power requirements: +5 V @ 3 A (typical) (for PCM-5820/5820L) +5 V @ 1.5 A (typical) (for PCM-5820E/5822) • Operating temperature: 0 ~ 60° C (32 ~ 140° F) • Weight: 0.77 kg (weight of total package) Jumpers and Connectors Connectors on the board link it to external devices such as hard disk drives, a keyboard or expansion bus connectors. In addition, the board has a number of jumpers that allow you to configure your system to suit your application. The tables below lists the function of each of the board's jumpers and connectors: Table 2-1: Jumpers Label J1 J2 2 Function Audio power source setting Clear CMOS PCM-5820 Series Startup Manual PCM-5820 Locating jumpers (component side) Locating Connectors J1: Audio power source Closed Pins *1 - 2 2-3 Voltage 5V 12 V J2: Clear CMOS Closed Pins *1 - 2 2-3 Result 3 V battery on Clear CMOS J3: Watchdog timer Closed Pins *1 - 2 2-3 Result Reset IRQ11 J4: COM2 selector Closed pins *1 - 2 3-4 5-6 Result RS-232 RS-422 RS-485 J5: Buzzer Pins *closed open Result Enabled Disabled J6: LCD power Closed pins *1 - 2 2-3 Voltage 5V 3.3 V J7: Ethernet power select Closed pins *1 - 2 2-3 Result 5V Standby 5 V Warning: Be sure to use the correct component side. Improper installation can cause serious Locating connectors component side (PCM-5820, PCM-5820L, PCM-5820E only) * default setting Locating connectors solder side (PCM-5820 Series) Locating connectors component side (PCM-5822 only) PCM-5820 Series Startup Manual 3 Mechanical Drawings Board Dimensions component side (PCM-5820, PCM-5820L, PCM-5820E only) Board Dimensions component side (PCM-5822 only) Board Dimensions solder side (PCM-5820 Series) 4 PCM-5820 Series Startup Manual