96HD500G-ST-SG5KA Test Report Initiated by River Lin Approved by Jackie Wang Page 1 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Revision History： Date 2014/07/05 Revision V1.0 Description The First version released. Creator River lin Page 2 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Test Results Definition： Criteria PASS Fail Limitation N/A No Test Definition Test result pass and function work perfectly. Test fail or can not meet the spec requirement. There are no plans to fix this function. Spec not support or driver not ready. No test tool or device or FW not ready, please write reason to the “Remark”. Page 3 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Test Results Summary： Num. Chapter 1 Test Item Result Function Test 1.01 HDD Function Test PASS 1.02 SATA IDE Mode Test PASS 1.03 SATA AHCI Mode Test PASS Chapter 2 Software Compatibility Test 2.01 Chapter 3 3.01 Chapter 3 Remark OS and Driver Install Test PASS Hardware Compatibility Test CPU Board Compatibility Test PASS System Reliability Test 4.01 Power On/Off Test PASS 4.02 Warm Boot Stress Test PASS 4.03 ACPI Cycling Burn-in Test PASS 4.04 Full System, I/O Integrated Stress Test PASS Page 4 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Table of Contents Revision History： .................................................................................................................................................. 2 Test Results Definition： ........................................................................................................................................ 3 Test Results Summary： ........................................................................................................................................ 4 Table of Contents .................................................................................................................................................... 5 Product Information： ........................................................................................................................................... 6 Platform Configuration: ......................................................................................................................................... 7 Test Programs： ................................................................................................................................................... 11 Test Equipments： ............................................................................................................................................... 12 1.01 HDD Function Test................................................................................................................................ 13 1.02 SATA IDE Mode Function Test ............................................................................................................ 15 1.03 SATA AHCI Mode Function Test......................................................................................................... 16 Chapter 2：Software Compatibility Test ............................................................................................................ 18 2.01 OS and Driver Install Test .................................................................................................................... 18 Chapter 3：Hardware Compatibility Test .......................................................................................................... 19 3.01 CPU Board Compatibility Test ............................................................................................................. 19 Chapter 4：System Reliability Test ..................................................................................................................... 20 4.01 Power On/Off Test................................................................................................................................. 20 4.02 Warm Boot Stress Test.......................................................................................................................... 21 4.03 ACPI Cycling Burn-in Test ................................................................................................................... 21 4.04 Full System, I/O Integrated Stress Test ................................................................................................ 22 Chapter 5：System Performance Test ................................................................................................................. 24 5.01 HDD Performance Test ......................................................................................................................... 24 Page 5 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Product Information： Item. Description. Advantech Part Number Manufacturer Seagate Model Number ST3500312CS From Factory 3.5” Interface SATAII Capacity 500GB Cache Capacity 8MB Rotation Speed(RPM) 5900RPM High instantaneous Transfer Rate 3GB/s I/O Data-transfer rate 300MB/s Power On Hour(POH) 8760 Annualized Failure Rate (AFR) 0.55% Voltage Tolerance +5.0V ± 5% and +12.0V ± 10%. Operating Temperature 0°C to 70°C Firmware SS16 Country of Origin China Dimension (W x H x D) 101.85mm x 20.20mm x146.99mm RoHS Status (Yes/No) Yes Page 6 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Platform Configuration: MIO-5290 Item. Description. Project Name. MIO-5290 PCB Version. A101-2 BIOS Version. 5290X015. EC Code Version. I1809X0100 CPU Model/Info Intel i3-3217UE @ 1.70GHz Memory Type/Info DDR3 1333 2GB Apacer 78.A2GC9.4200C Total Memory Size 8GB PCH Chipset QM77 Graphic Controller VGA Function was supported intel PCH Audio Codec ALC892 LAN1 Controller Intel® 82579LM LAN2Controller Intel®82583V MIO-5271 Item. Description. Project Name. MI0-5271 PCB Version. A101-2 BIOS Version. 5271X017 EC Version I2865X0101 CPU Model/Info Intel® i5-4300 1.0GHz Memory Type/Info/Size DDR3L-1600 4GB Apacer 78.B2GCR.AF10C PCH Chipset Lynx Point-LP PCH QM87 Graphic Controller GT3 Graphics, Generation 7.5 graphics core architecture Audio Codec ALC888S LAN1 Controller Intel i218 LAN2 Controller Intal i210 AIMB-582W Item. Description. Page 7 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. M/B Name AIMB-582WG2 PCB Version. A101-2 BIOS Version. W582J03 CPU Model/Info Intel® E3 1275 3.5GHz Memory Type/Info/Size DDR3 1333G*2 PCH Chipset C216 Graphic Controller Intel ® HD Graphics Audio Codec ALC892 LAN1 Controller Intel ® 82583V LAN2 Controller Intel ® 82579LM AIMB-503L Item. Description. Project Name. AIMB-503 PCB Version. A101-3 BIOS Version. A503X009 CPU Model/Info Intel® i5-4670S 3.1GHz Memory Type/Info DDR3 1333G*2 PCH Chipset Intel H81 PCH Graphic Controller Intel HD Graphic Audio Codec ALC892 LAN1 Controller Realtek 8111E LAN2Controller Realtek 8111E AIMB-584 Item. Description. Project Name. AIMB-584 PCB Version. A101-1 BIOS Version. A584X021 CPU Model/Info Intel® i5-4670S 3.1GHz Memory Type/Info DDR3 1333G*2 PCH Chipset Intel Q87 PCH Page 8 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Graphic Controller Intel HD Graphic Audio Codec ALC892 LAN1 Controller Intel® I217 LAN2Controller Intel® I211 AIMB-784 Item. Description. Project Name. AIMB-784 PCB Version. A101-3 BIOS Version. A784X018 CPU Model/Info Intel® i7-4770S 3.1GHz Memory Type/Info DDR3 1333G*2 PCH Chipset Intel Q87 PCH Graphic Controller Intel HD Graphic Audio Codec ALC892 LAN1 Controller Intel® I217 LAN2Controller Intel® I211 PCE-5128 Item. Description. M/B Name PCE-5128 PCB Version. A101-3 BIOS Version. 5128X202 Backplane Model. PCE-5B06-03 Backplane Verson. A101-2 CPU Model/Info Intel® i7-4770S 3.1GHz Memory Type/Info/Size DDR3 1333G*2 PCH Chipset Intel Q87 PCH Graphic Controller Intel HD Graphic LAN1 Controller Intel® I217 LAN2 Controller Intel® I210 PCE-7128 Page 9 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Item. Description. M/B Name PCE-7128 PCB Version. A101-3 BIOS Version. 7128X210 Backplane Model. PCE-5B06-03 Backplane Verson. A101-2 CPU Model/Info Intel® i7-4770S 3.1GHz Memory Type/Info/Size DDR3 1333G*2 PCH Chipset Intel C226 PCH Graphic Controller Intel HD Graphic LAN1 Controller Intel® I217 LAN2 Controller Intel® I211 Page 10 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Test Programs： Test Program Version CrystalDiskMake V3.0.3 ATTO Disk V2.46 Anvil's Storage Utilities 1.1.0.337 Passmark performance V8.0 build1031 I/OMETTER 2004.07.30 PassMark Burn-In Test Pro V7.1 build 1017 PassMark Rebooter V1.3 build 1004 PassMark Sleeper V2.3 build 1009 Power on/off V3.3 Page 11 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Test Equipments： Model Description Power on/off test equipment (ATX/AT) Page 12 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Chapter 1：Function Test 1.01 HDD Function Test 1.01.01.01 Test Purpose： The purpose of SATA test is to analyze and validate the functional、performance capabilities、quality and stability. 1.01.01.02 Test Standard： Please refer to the Project Hardware and BIOS specification. 1.01.01.03 Test Tool： 1. SATA cable 2. SATA HDD 3. SATA DVD-ROM 1.01.01.04 Test Criteria： 1. The BIOS must detect SATA devices information. 2. The SATA function can install OS and work well on OS without hang, restart, or blue screen or any problems. 3. The Device Management can not have any exclamation point and question mark. 4. Mark sure pass w/program without any error ocurrs. 1.01.01.05 Test Procedure： 1. 2. 3. 4. 5. Insert SATA HDD and DVD-ROM into the DUT The BIOS detect SATA port HD correct information. Install OS and all drivers. SATA HDD can be copy/del/read/write file. Install the PassMark BurnIn Pro program, and setting : (a) Select tests to perform and their duty cycle: Select Disk(s) and Optical Drive(s)/ 100% Loading/Auto Stop After : 30Minutes. (b) Set test preferences: Select “Disk”-> Select Test this drive/ set File size: 15(% of disk), other setting value keep defaults Preference. (c) Then Press “Start selected tests” for test. 6. After finished testing, the test result will show on screen. 7. Change other port, and repeat 1~6. 1.01.01.06 Test Data： Page 13 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Test Item Description Result Post information POST should show the correct model name PASS BIOS information BIOS detect correct information PASS Device Manager Device Management can not have any exclamation point and question mark, and detect correct information PASS Install OS &driver Can install OS and driver PASS SATA Port Mark should all SATA port can detect and reboot shutdown PASS BurnIn Running passmark 30mins PASS Page 14 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark 1.02 SATA IDE Mode Function Test 1.03.01.01 Test Purpose： The purpose of this test is to ensure the functional of the SATA IDE Mode. 1.03.01.02 Test Standard： Please refer to the Project Hardware and BIOS specification 1.03.01.03 Test Tools： 1. SATA HDD 2. SATA DVD-ROM 3. PassMark Burn In test Pro 1.03.01.04 Test Criteria： 1. The BIOS Setting IDE mode for DUT. 2. DUT must install OS and all drivers forIDE mode without any problems or error occurs. 1.03.01.05 Test Procedure： 1. 2. 3. 4. Plug SATA HDD and DVD-ROM into DUT. Setting IDE mode of SATA Mode on BIOS. To install OS and drivers. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show on screen. 5. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat 3times. 6. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat 3times. 7. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat 3times. 8. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can work properly, and repeat 3times. 9. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times. 1.03.01.06 Test Data： Test Item SATA IDE Mode Description Result Win7 Ultimate SP1_X86 Installation Test. PASS Win8.1 Pro_X86 Installation Test. PASS ACPI S4 Mode PASS OS shut dowm PASS Warm Boot Test. PASS Page 15 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark 1.03 SATA AHCI Mode Function Test 1.03.01.07 Test Purpose： The purpose of this test is to ensure the functional of the SATA AHCI Mode. 1.03.01.08 Test Standard： Please refer to the Project Hardware and BIOS specification 1.03.01.09 Test Tools： 4. SATA HDD 5. SATA DVD-ROM 6. PassMark Burn In test Pro 7. Intel F6 Install Floppy Driver or AHCI driver on USB flash disk. 1.03.01.10 Test Criteria： 3. The BIOS Setting AHCI mode for DUT. 4. DUT must install OS and all drivers for AHCI mode without any problems or error occurs. 1.03.01.11 Test Procedure： 10. Plug SATA HDD and DVD-ROM into DUT. 11. Setting AHCI mode of SATA Mode on BIOS. 12. To install OS and drivers, during install process, need to upload AHCI driver from Floppy or USB flash disk. 13. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show on screen. 14. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat 3times. 15. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat 3times. 16. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat 3times. 17. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can work properly, and repeat 3times. 18. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times. 19. Setting Enabled Hot Plug SATA Port on BIOS. 20. The DUT SATA should be Hot Plug and work properly, and repeat 3times. 1.03.01.12 Test Data： Test Item SATA AHCI Mode Description Result Win7 Ultimate SP1_X64 Installation Test. PASS Win8.1 Pro_X64 Installation Test. PASS Page 16 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark ACPI S4 Mode PASS OS shut dowm PASS Warm Boot Test. PASS Hot Plug PASS Page 17 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Chapter 2：Software Compatibility Test 2.01 OS and Driver Install Test 2.01.01.01 Test Purpose： The purpose of this test is to ensure the OS compatibility of the DUT. 2.01.01.02 Test Standard： Please refer to the Project Hardware and BIOS specification 2.01.01.03 Test Tools： 1. Microsoft OS installation DVD depends on X86/X64. 2.01.01.04 Test Criteria： 1. The OS X86/X64 installation process must complete without any error occurs. 2. The Server OS X86/X64 installation process must complete without any error occurs. 3. Device Management can not have any exclamation point and question mark. 2.01.01.05 Test Procedure： 1. Plug OS DVD or Server OS into DVD-ROM, and start install follow installation process. 2. After finish OS install, install all drivers for the DUT. 3. Make sure drivers of the DUT can install, and device management can not have any unknown device. 2.01.01.06 Test Data： Test Item Win7 Ultimate SP1 x86 Win7 Ultimate SP1 x64 Win8.1 Pro x86 Win8.1 Pro x64 Description Result OS Installation – English. PASS Driver Installation. PASS Device Management Check. PASS OS Installation – English. PASS Driver Installation. PASS Device Management Check. PASS OS Installation – English. PASS Driver Installation. PASS Device Management Check. PASS OS Installation – English. PASS Driver Installation. PASS Device Management Check. PASS Page 18 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remake Chapter 3：Hardware Compatibility Test 3.01 CPU Board Compatibility Test 3.01.01.01 Test Purpose： The purpose of this test is to validate and ensure the CPU Board compatibility of the DUT. 3.01.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification. 3.01.01.03 Test Tools： 1. Different Chipsets of CPU Board 3.01.01.04 Test Criteria： 1. With a different CPU board connected. The DUT must PASS without any error occurs. 2. BIOS must detect current information 3. Device Management can not have any exclamation point and question mark. 3.01.01.05 Test Procedure： 1. Connect to CPU board and power on. 2. The system should be detected HDD, then install OS and drivers for this. 3. Confirm the all kinds of CPU board should work properly. 3.01.01.06 Test Data： Test Item CPU board Description BIOS version PCB Version Result Remark OS install MIO-5290 5290X015 A101-2 Win7/Win8.1 PASS MIO-5271 5271X017 A101-2 Win7/Win8.1 PASS AIMB-582W W582XJ03 A101-2 Win7/Win8.1 PASS AIMB-503L A503X009 A101-3 Win7/Win8.1 PASS AIMB-584 A584X021 A101-1 Win7/Win8.1 PASS AIMB-784 A784X018 A101-3 Win7/Win8.1 PASS PCE-5128 5128X202 A101-3 Win7/Win8.1 PASS PCE-7128 7128X201 A101-3 Win7/Win8.1 PASS Page 19 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Chapter 4：System Reliability Test 4.01 Power On/Off Test 4.01.01.01 Test Purpose： The purpose of this test is to examine and validate the stability of the Power On/Off and AT mode under Widows OS. 4.01.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification 4.01.01.03 Test Tools： 1. Power on/off test equipment. 2. Power on/off Program 4.01.01.04 Test Criteria： 1. The test msut PASS the Power on / off circling test >= 100 times, booting rate＝100% 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any problems. 3. The system must have no any error w/ Program. 4.01.01.05 Test Procedure： 1. 2. 3. 4. Connect Power on/off test equipment to DUT for Power on/off test Make sure PSON1 or HW Jumper set as ATX Mode. Make sure BIOS item: After AC power Failure MUST set as "Always Off". Install and execute Power on/off Program, and setting Timer ：hr/min/sec on DUT. 5. Setup testing time, and change to zero of run number on Power on/off test equipment. 6. Start power on/off test and pass over100 times. 7. Make sure PSON1 or HW Jumper set as AT Mode 8. Repeat 4~5 and start power on/off test for AT mode and pass over 100 times. 4.01.01.06 Test Data： Test Item Description Result Power On/Off test (ATX mode) 1. BIOS item: After AC power Failure set as "Always Off" 2. H/W jumper set as ATX mode 3. Test at room temperature for 1000 duration cycles 3. Booting rate =100% PASS Power On/Off test (AT mode) 1. BIOS item: After AC Power Failure set as "Always Off". 2. H/W jumper set as AT mode 3. Test at room temperature for 1000 duration cycles 4. Booting rate =100% PASS Page 20 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark 4.02 Warm Boot Stress Test 4.02.01.01 Test Purpose： The purpose of this test is to analyze and validate the functional、performance capabilities、quality and stability of DUT warm boot capability. 4.02.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification 4.02.01.03 Test Tools： 1. PassMark Rebooter 4.02.01.04 Test Criteria： 1. The test msut PASS the Reboot circling test >= 100 times, booting rate＝100% 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any problems. 3. The system must have no any error w/ Program. 4.02.01.05 Test Procedure： 1. Install PassMark Rebooter program. 2. Executing program, and setting (a) Maxiimum reboots 100 cycles. (b) Delay Time Out setting before each reboot: 20~25 sec. (c) Enabled Auto load Rebooter at startup. 3. Then start test Cycle. 4.02.01.06 Test Data： Test Item Description 1.Run PassMark Rebooter V1.3 Build1004 Windows 7 Ultimate SP1 2. Must PASS for 100 duration cycles. X64 3.Time Out Before reboot:10-25secs 4. Booting rate =100% Result Remark PASS 4.03 ACPI Cycling Burn-in Test 4.03.01.01 Test Purpose： The purpose of this test is to examine and validate the quality and stability of the DUT ACPI capability. 4.03.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification 4.03.01.03 Test Tools： 1. PassMark Sleeper V2.3 Build1009 4.03.01.04 Test Criteria： Page 21 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. 1. The ACPI function test msut PASS run 100 times 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any other problems. 4.03.01.05 Test Procedure： 1. Install PassMark Sleeper on the DUT. 2. Setup ACPI support mode. 3. Press Configuration-> Cycles Settings-> Cycle forever, then press ok. 4. Press Sleeper Now and start test 100 times. 4.03.01.06 Test Data： Test Item Windows 7 Ultimate SP1 X64 Description 1. Run PassMark Sleeper V2.3 build 1009. 2. Select "all supported states". (S4) 3. Run for 100 times. The DUT MUST maintain a stable condition after the test has been completed. Result Remark PASS 4.04 Full System, I/O Integrated Stress Test 4.04.01.01 Test Purpose： The purpose of this test is to examine and validate the quality and stability all IO of the DUT. 4.04.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification 4.04.01.03 Test Tools： 1. PassMark BurnIn Pro 4.04.01.04 Test Criteria： 1. The Full loading test msut PASS run over 12hours 2. The DUT must maintain a stable condition without any system crash, hang, blue screen, restart or any other problems. 3. The system must have no any error w/ PassMark BurnIn Pro Program. 4.04.01.05 Test Procedure： 1. Insert tool into all of IO port on DUT. 2. Install PassMark BurnIn Pro program. 3. Executing BurnIn test, and setting : (a) Select tests toperform and their duty cycle: Setp Auto Stop “720” Minutes, select need to test items (b) Set test preferences: setup need to setting items. (c) All setting finish, press “Start selected tests” for test. 4. The DUT run program over 12hours. 4.04.01.06 Test Data： Page 22 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. I/O Integrated Stress Test: Windows 7 Ultimate SP1 X64 Test Item Description Result CPU 100% Loading PASS RAM 100% Loading PASS VIDEO 100% Loading PASS 2D Graphics 100% Loading PASS 3D Graphics 100% Loading PASS SATA1 SATA HDD Seagate ST3250312AS File system: NTFS PASS SATA2 SATA HDD Seagate ST3500312CS File system: NTFS PASS Page 23 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark Chapter 5：System Performance Test 5.01 HDD Performance Test 5.01.01.01 Test Purpose： The purpose of this test is to ensure the HDD performance of the DUT. 5.01.01.02 Test Standard： Please refer to the Project Hardware specification and BIOS specification. 5.01.01.03 Test Tools： 1. CrystalDiskMark 2. ATTO Disk Benchmark 3. Anvil's Storage Utilities 4. Passmark performance 5. I/OMETTER 5.01.01.04 Test Criteria： 1. Executing the BenchmarkTest default item of CrystalDiskMark 2. Executing the BenchmarkTest of AS AUTO Disk Benchmark 3. Executing the BenchmarkTest SSD Benchmark of Anvil's Storage Utilities 4. Executing the BenchmarkTest Disk of Passmark performance 5. Executing the BenchmarkTest Disk of I/O Meter 5.01.01.05 Test Procedure： 1. Install and execute CrystalDiskMark, setting “need to test HDD” and press “All” start test. 2. Install and execute ATTO Disk Benchmark, setting Drive “need to test HDD” and press “Start” for test. 3. Install and execute Anvil's Storage Utilities, setting SSD Benchmark and “need to test HDD” then start test. 4. Install and execute Passmark performance, setting Disk and “need to test HDD” then pres”All” start test. 5. Install and execute of I/O Meter, setting PHYSICAL Drive and Disker Worker, then start test. 6. Install and execute of I/O Meter, setting need to test Disk and Disker Worker, then start test. 7. Record all of test results. 5.01.01.06 Test Data： HDD Performance (OS:Win7 Ultimate SP1 X64) Test Item and Comment / Software (unit) Crystal Read Max Read DiskMa (MB/s) Seq MIO -5290 MIO -5271 AIMB -582W AIMB -503 AIMB -584 AIMB -784 PCE -5128 PCE -7128 112.7 112.5 112.5 112.3 112.3 112.4 112.3 112.4 Page 24 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark Write Max Write rk 111.6 (MB/s) Seq 111.4 111.9 111.5 111.4 111.4 111.3 111.4 AIMB -503 AIMB -584 AIMB -784 PCE -5128 PCE -7128 HDD Performance (OS: Win7 Ultimate SP1 X64) MIO -5290 Test Item and Software ATTO Read (MB/s) Disk Benchmark Write (MB/s) MIO -5271 AIMB -582W Remark 112.993 113.237 113.482 113.482 113.237 113.482 112.75 113.237 113.237 112.75 112.993 112.508 111.848 113.237 112.75 112.267 HDD Performance (OS: Win7 Ultimate SP1 X64) Test Item and Software Anyil’s Storage Utilities MIO -5290 MIO -5271 AIMB -582W AIMB -503 AIMB -584 AIMB -784 PCE -5128 PCE -7128 Read (MB/s) 137.85 137.92 137.82 137.64 137.15 137.5 137.5 137.96 Write (MB/s) 85.46 86.2 85.79 84.21 Totaal 223.31 224.0 86.2 86.23 84.78 Remark 84.4 224.02 223.86 221.94 223.39 221.71 227.37 HDD Performance (OS: Win7 Ultimate SP1 X64) Test Item and Software PassMark Read (MB/s) Performance MIO -5290 MIO -5271 AIMB -582W AIMB -503 AIMB -584 AIMB -784 PCE -5128 PCE -7128 785 512 782 749 726 741 724 720 PCE -5128 PCE -7128 Remark HDD Performance (OS: Win7 Ultimate SP1 X64) Test Item and Software MIO -5290 MIO -5271 AIMB -582W AIMB -503 AIMB -584 AIMB -784 Total I/O per 10308.05 15829.26 14842.56 14011.29 14570.62 15418.62 14201.19 15068.6 Second Total I/O MBs Second I/O METER Average (Physical) I/O Response Time(ms) 40.27 61.83 57.98 54.73 56.92 60.23 55.47 58.86 0.0963 0.0627 0.0669 0.0709 0.0681 0.0644 0.0699 0.0659 Maximum I/O 102.0857 49.932 Response Time(ms) 96.6048 34.619 47.7085 49.8318 99.7128 53.0598 Page 25 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark HDD Performance (OS: Win7 Ultimate SP1 X64) Test Item and Software MIO -5290 MIO -5271 AIMB -582W AIMB -503 AIMB -584 AIMB -784 PCE -5128 PCE -7128 Total I/O per 9892.38 15800.15 13856.65 15333.44 13299.32 13070.45 15229.05 15140.07 Second Total I/O MBs Second 38.63 61.72 54.13 59.9 51.95 51.06 59.49 59.14 I/O METER Average (Logical) I/O 0.1004 Response Time(ms) 0.0629 0.0717 0.0647 0.0746 0.0759 0.0652 0.0656 Maximum I/O 30.8107 44.9613 21.8957 14.5164 16.5186 14.6552 19.0195 17.0382 Response Time(ms) Page 26 of 26 Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission. Remark