E D050S C 3 V ers ion: 2.0 T E CHNICA L MODE L SPE CIFICA T ION NO. : E D050SC3 T he content of this information is subject to be changed without notice. Please contact PV I or its agent for further information Customer•s Confirmation Customer Date By PV I•s Confirmation FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com Confirmed B y Prepared B y T he information contained herein is the exclus ive property of P rime V iew International C o., Ltd. and s hall not be dis tributed, reproduced, or dis clos ed in whole or in part without prior written permis s ion of P rime V iew International C o., Ltd. P AG E :1 ED050SC3 Revision History Rev. Issued Date Revised 1.0 August.15.2008 New Contents Add Page 7 6-2) Absolute maximum rating Page 16 11.Bar Code definition Page 17 12.Border definition Modify Page 4 3. Mechanical Specifications Page 7 6-3) Panel DC characteristics Page 9 7.Power on sequence 2.0 October.7.2008 Page 14 9. Handling, Safety and Environment Requirements Del Preliminary specification Page 15 10.Reliability test 14.Stylus Tapping Top R:0.4mm Load: 300gf Speed: 5 times/sec Total 13,500times change to Top R:0.8mm Load: 300gf Speed: 2 times/sec Total 13,500times Del Page 13 Note 8-1 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:2 ED050SC3 TECHNICAL SPECIFICATION CONTENTS NO. ITEM PAGE - Cover 1 - Revision History 2 - Contents 3 1 Application 4 2 Features 4 3 Mechanical Specifications 4 4 Mechanical Drawing of EPD module 5 5 Input/Output Terminals 6 6 Electrical Characteristics 7 7 Power on Sequence 10 8 Optical Characteristics 12 9 Handling, Safety and Environment Requirements 14 10 Reliability test 15 11 Bar Code Definition 16 12 Border Definition 17 13 Block Diagram 17 14 Packing 18 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:3 ED050SC3 1. Application The display is a TFT active matrix electrophoretic display, with associated interface and control logic, and a reference system design. The 5” active area contains 800x600 pixels, and has full 1~4 bit display capabilities An integrated circuit containing interface, timing and control logic is supplied with each panel. 2. Features High contrast TFT electrophoretic 800x600 display High reflectance Ultra wide viewing angle Ultra low power consumption Pure reflective mode Bi-stable Commercial temperature range Landscape, portrait mode Antiglare hard-coated front-surface 3. Mechanical Specifications Parameter Screen Size Display Resolution Active Area Pixel Pitch Pixel Configuration Specifications 5 800 (H) ͪ600(V) 101.6 (H)ͪ76.2 (V) 0.127(H)x0.127(V) Rectangle Outline Dimension 114.6(H) ͪ89.6(V) ͪ1.18(D) (panel area height) 114.6(H) ͪ89.6(V) ͪ2.0(D) (FPC area height with capacitor) mm 24̈́2 g Module Weight Unit Inch Pixel mm mm Remark Panel height is measured without released film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:4 ED050SC3 4. Mechanical Drawing of EPD Module The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:5 ED050SC3 5. Input/Output Terminals 5-1)Pinout List Pin # Signal Description 1 VNEG Negative power supply source driver 2 NC NO Connection 3 VPOS Positive power supply source driver 4 NC NO Connection 5 VSS Ground 6 NC NO Connection 7 VDD Digital power supply drivers 8 XCL Clock source driver 9 XLE Latch enable source driver 10 XOE Output enable source driver 11 XSHR Shift direction source driver 12 XSTL2 Start pulse source driver 13 D0 Data signal source driver 14 D1 Data signal source driver 15 D2 Data signal source driver 16 D3 Data signal source driver 17 D4 Data signal source driver 18 D5 Data signal source driver 19 D6 Data signal source driver 20 D7 Data signal source driver 21 NC NO Connection 22 VCOM Common connection 23 NC NO Connection 24 VGG Positive power supply gate driver 25 NC NO Connection 26 VEE Negative power supply gate driver 27 NC NO Connection 28 MODE2 Output mode selection gate driver 29 MODE1 Output mode selection gate driver 30 XRL Shift direction gate driver 31 SPV Start pulse 1st gate driver 32 CKV Clock 1st gate driver 33 BORDER Border connection The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:6 ED050SC3 6.Electrical Characteristics 6-1) Panel interface description This panel is driven by ASIC PVI-6001A or “Apollo” display controller ASIC. See control product specification for details. 6-2) Absolute maximum rating Parameter Logic Supply Voltage Positive Supply Voltage Negative Supply Voltage Max .Drive Voltage Range Supply Voltage Supply Voltage Supply Range Operating Temp. Range Storage Temperature Symbol VDD VPOS VNEG VPOS - VNEG Rating -0.3 to +7 -0.3 to +18 +0.3 to -18 36 Unit V V V V VGG VEE VGG-VEE TOTR TSTG -0.3 to +45 -25.0 to +0.3 -0.3 to +45 0 to +50 -25 to +70 V V V к к 6-3) Panel DC characteristics Parameter Min Typ Max Unit VSS - 0 - V VDD 3.0 3.3 3.6 V - 0.5 1 mA -21 -20 -19 V - 5 15 mA 21 22 23 V - 1.4 4.2 mA -15.4 -15 -14.6 V - 22 44 mA 14.6 15 15.4 V VPOS = 15V - 24 48 mA VPOS = 15V 14.6 15 15.4 V VNEG = -15V -15.4 -15 -14.6 V VPOS+VNEG 0 Adjusted 800 -1.0 mV VCOM -800 -2.5 ICOM - 0.25 - mA Maximum power panel PMAX - - 1850 mW Standby power panel PSTBY - - 0.4 mW Typical power panel PTYP - 850 - mW 0 - 50 к -25 - 70 к - 1000 - ms Signal ground Logic Voltage supply Gate Negative supply Gate Positive supply Source Negative supply Source Positive supply Symbol IVDD IEE IGG INEG time at 25к VNEG = -15V VPOS IPOS VAsym Maximum image update VGG = 22V VNEG Asymmetry source Storage temperature VEE =-20V VGG VBorder Operating temperature VDD=3.3V VEE Border supply Common voltage Conditions V The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:7 ED050SC3 - The maximum power and maximum currents are specified for the worse case power consumption. This occurs when 2 horizontal inverted stripped images are displayed - The typical power is the consumed power when “typical images” are displayed. - The standby power is the consumed power when the panel controller is in standby mode. - The listed electrical/optical characteristics are only guaranteed under the controller & waveform provided by PVI - Vcom is recommended to be set in the range of assigned value ̈́ 0.1V 6-4 )Panel AC characteristics VDD=3.0V to 3.6V, unless otherwise specified. Parameter Symbol Min. Typ. Max. Unit Clock frequency fckv - - 200 kHz Minimum “L” clock pulse width twL 0.5 - - us Clock rise time trckv - - 100 ns Clock fall time tfckv - - 100 ns Data setup time tSU 100 - - ns Data hold time tH 100 - - ns Pulse rise time trspv - - 100 ns Pulse fall time tfspv - - 100 ns Clock CL cycle time tcy 50 - DC ns D0 .. D7, SPH setup time tsu 8 - - ns D0 .. D7, SPH th 1 - - ns Below tLEdly 40 - - ns table hold time LE on delay time LE high-level pulse width tLEw 40 - - ns LE off tLEoff 40 - - ns delay time App Pin CKV CKV, SPV SPV CLOCK & DATA TIMING CL tLEoff tLEdly LE tLE tOUT OUT1 ~ OUT400 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:8 ED050SC3 OUTPUT LATCH CONTROL SIGNALS SPH tstls tstlh 10% 10% CL tcy D0~D7 90% 90% 10% 10% th tsu tfckv CKV twl trckv 90 SPV 90 10 10 tus th tfspv trspv 90 90 10 10 6-5) Power Consumption Parameter Symbol Conditions TYP Max Unit Maximum panel power consumption during update. - - - 1850 mW Power consumption in standby mode - - - 0.4 mW Typical panel power - - 850 - mW Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:9 ED050SC3 7.Power on Sequence 1. VSS VDD VNEG VPOS (Source driver) 2. VEE VGG(Gate driver) ϠPower on sequence’s timing chart as blew : VGG V POS T1 T2 T3 T4 T5 T6 T7 VDD VSS VEE V NEG Logic signal input T1: 100 µs(min) T2: 0µs(min) T3: 1000µs (min) T4: 0 µs ( min) T5: 0 µs (min) T6: 0 µs (min) T7: 0 µs (min) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:10 ED050SC3 ϠIt is expanded as blew. VDD Sequence VPOS Sequence VNEG VEE Sequence Sequence VGG Sequence Logic signal input Sequence The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:11 ED050SC3 8. Optical characteristics 8-1)Specifications Measurements are made with that the illumination is under an angle of 30 degrees, the detection is perpendicular unless otherwise specified. T = 25oC SYMBOL PARAMETER CONDITIONS MIN TYP. MAX UNIT R Reflectance White 30 35 - % Note - Gn Nth Grey Level - - DS+(WS-DS)ͪn/(m-1) - L* - CR Contrast Ratio - 6 - - Tupdate Update time 2~4-bit mode 1-bit mode 1000 540 - ms ms - WS: White state , DS: Dark state, Gray state from Dark to White :DSΕG1ΕG2…ΕGn…ΕGm-2ΕWS m:4Ε8Ε16 when 2Ε3Ε4 bits mode 8-2)Definition of contrast ratio The contrast ratio (CR) is the ratio between the reflectance in a full white area (Rl) and the reflectance in a dark area (Rd): CR = Rl/Rd The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:12 ED050SC3 8-3)Reflection Ratio The reflection ratio is expressed as: R = Reflectance Factorwhite board x ( Lcenter / Lwhite board ) Lcenter is the luminance measured at center in a white area (R=G=B=1). Lwhite board is the luminance of a standard white board. Both are measured with equivalent illumination source. The viewing angle shall be no more than 2 degrees. α = declination / θ = azimuth The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:13 ED050SC3 9.HANDLING, SAFETY AND ENVIROMENTAL REQUIREMENTS WARNING The display glass may break when it is dropped or bumped on a hard surface. Handle with care. Should the display break, do not touch the electrophoretic material. In case of contact with electrophoretic material, wash with water and soap. CAUTION The display module should not be exposed to harmful gases, such as acid and alkali gases, which corrode electronic components. Disassembling the display module can cause permanent damage and invalidate the warranty agreements. Observe general precautions that are common to handling delicate electronic components. The glass can break and front surfaces can easily be damaged. Moreover the display is sensitive to static electricity and other rough environmental conditions. Data sheet status Product This data sheet contains final product specifications. specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:14 ED050SC3 10. Reliability test ʳ TEST CONDITION METHOD T = +50°C, RH = 30% for 240 hrs 6 High-Temperature Operation Low-Temperature Operation High-Temperature Storage Low-Temperature Storage High-Temperature, High-Humidity Operation High Temperature, High- Humidity Storage IEC 60 068-2-2Bp IEC 60 068-2-2Ab IEC 60 068-2-2Bp IEC 60 068-2-1Ab IEC 60 068-2-3CA IEC 60 068-2-3CA 7 Temperature Cycle 8 UV exposure Resistance 765 W/m for 168hrs,40к 9 Package Vibration 1.04G, Frequency: 10~500Hz Direction: X,Y,Z Duration: 1 hours in each direction Full packed for At the end of the test, electric, mechanical, shipment and optical specifications shall be satisfied. 10 Package Drop Impact Drop from height of 122 cm on concrete surface. Drop sequence: 1 corner, 3 edges, 6 faces One drop for each. Full packed for At the end of the test, electric, mechanical, shipment and optical specifications shall be satisfied. 11 Electrostatic Effect (non-operating) (Machine model)+/- 250V 0Ө, 200pF IEC 62179, IEC At the end of the test, electric, mechanical, 62180 specifications shall be satisfied.ʳ ʳ 12 Altitude test Operation 700hPa ( = 3000m )48Hr 13 Altitude test Storage 260hPa ( = 10000m )48Hr 1 2 3 4 5 14 Stylus Tapping T = 0°C for 240 hrs T = +70°C, RH=23% for 240 hrs T = -25°C for 240 hrs T = +40°C, RH = 90% for 168 hrs T = +50к, RH=80% for 240hrs 1 cycle:[-25к 30min]Ш[+70к 30 min] :100 cycles 2 REMARK At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, IEC 60 068-2-14 specifications shall be satisfied.ʳ IEC60 068-2-5Sa POLYACETAL Pen: Top R:0.8mm Load: 300gf Speed: 2 times/sec Total 13,500times, Optical characteristics shall be satisfied. At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ ʳ ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ ʳ Pass criteria – no glass breakage or damage to microcapsules. Actual EMC level to be measured on customer application The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:15 ED050SC3 11. Bar Code definition E0Y 00 4 01 1 I 1 2 3 4 2 5 7 6 4 2 00361 7 A 2 T 8 1 ΚEPD model code: ED050SC3:E0Y 2 ΚInternal control codes: 3 ΚFPL reversion code V100:3,V110:4 4 ΚFPL batch code: (BL/P/B...)001~009:01~99, 100~109:A0~A9, 110-119:B0~B9… 320~329:Z0~Z9 5 ΚYear: F:2005 / G:2006 / H:2007 / I:2008 /... / Z:2025 6 ΚMonth: 1:Jan. 2:Feb. ... 9:Sep. A:Oct. B:Nov. C:Dec. 7 ΚSerial number 8 ΚMFG code: TOC:T, PVI:P The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:16 ED050SC3 12. Border definition 13.Block Diagram ˣ˴́˸˿ ˩ʳ˗̅˼̉˸̅ ʻ ˚˴̇˸ʼ ˛ʳ˗̅˼̉˸̅ ʻ ˦̂̈̅˶˸ʼ 33 PIN Input The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:17 ED050SC3 14.Packing The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:18