PO023OX1 Version：2.0 TECHNICAL SPECIFICATION MODEL NO. : PO023OX1 The content of this information is subject to be changed without notice. Please contact PVI or its agent for further information Customer’ s Confirmation Customer Date FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com By PVI’ s Confirmation Confirmed By Prepared By The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:1 PO023OX1 Revision History Rev. 1.0 2.0 Issued Date Engineer Revised Contents Apr. 01, 2008 吳昌霖 New Aug. 21, 2009 吳昌霖 Depend on ECN200907022 to modify packing drawing The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:2 PO023OX1 TECHNICAL SPECIFICATION CONTENTS NO. ITEM PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Cover Revision History Contents Application Features Mechanical Specifications Mechanical Drawing of TFT-LCD module Input / Output Terminals Absolute Maximum Ratings Electrical Characteristics Pixel Arrangement Block Diagram Timing specification Interface specification Optical Characteristics Handling Caution Reliability Test Packing 1 2 3 4 4 4 5 6 7 8 9 9 10 12 14 17 19 20 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:3 PO023OX1 1. Application： The PO023OX1 applies to a color TFT LCD module which has octagonal outline. PO023OX1 module applies to OA product, GPS, which require high quality flat panel display. If you must use in high reliability environment can’ t over reliability test condition. 2. Features： . . . . . . Pixel in stripe configuration Slim and compact Wide viewing angle High Brightness Octagonal LCD Driver IC：HX8325 3. Mechanical Specifications： Parameter Screen Size Display Format Display Colors Active Area Pixel Pitch Pixel Configuration Outline Dimension Weight Surface treatment Back Light Display mode Gray scale inversion direction Specifications 2.3” TFT LCD 240×(R, G, B)×240 65,536 D = 57.96 (Circular) 0.2415×0.2415 Stripe 75.60(W)×75.70(H)×7.64(D) 46±5 Anti-glare and wide-view film 2-LED,150mA Normally white 6 [Refer to Note 12-1] Unit inch dot mm mm mm g o’ clock The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:4 PO023OX1 4. Mechanical Drawing of TFT-LCD Module： The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:5 PO023OX1 5. Input / Output Terminals： LCD Module Connector FPC Down Connect, 30 Pins Pin No. Signal Pin Function 1 VSS Ground 2 VSS Ground 3 NRESET Reset Input Pin 4 Dummy N.C. 5 D15 Parallel Data Bus (R4) 6 D14 Parallel Data Bus (R3) 7 D13 Parallel Data Bus (R2) 8 D12 Parallel Data Bus (R1) 9 D11 Parallel Data Bus (R0) 10 D10 Parallel Data Bus (G5) 11 D9 Parallel Data Bus (G4) 12 D8 Parallel Data Bus (G3) 13 D7 Parallel Data Bus (G2) 14 D6 Parallel Data Bus (G1) 15 D5 Parallel Data Bus (G0) 16 D4 Parallel Data Bus (B4) 17 D3 Parallel Data Bus (B3) 18 D2 Parallel Data Bus (B2) 19 D1 Parallel Data Bus (B1) 20 D0 Parallel Data Bus (B0) 21 Dummy N.C. 22 NRD_E Read Signal Pin 23 NWR_RNW Write Signal Pin 24 DNC_SCL Register Index or Register Command Select 25 NCS Chip Select Pin 26 Dummy N.C. 27 VCI Power Supply (Typ. 3.0V) 28 VCI Power Supply (Typ. 3.0V) 29 VSS Ground 30 VSS Ground Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:6 PO023OX1 6. Absolute Maximum Ratings： The followings are maximum values, which if exceeded, may cause faulty operation or damage to the unit. Item Symbol Power supply voltage (1) VCC, IOVCC Power supply voltage (2) VCI Power supply voltage (3) VLCD-VSSA Power supply voltage (4) VSSA-VCL Drive Supply Voltage VGH-VGL Input Voltage Range Output Voltage Range VIN VO Note Note Note Note Note Note VSS=GND=0V , Ta = 25℃ Value Unit Remark Note 6-1 -0.3 to +4.6 V Note 6-2 Note 6-1 -0.3 to +4.6 V Note 6-3 Note 6-1 -0.3 to +6.5 V Note 6-4 Note 6-1 -0.3 to +4.6 V Note 6-5 Note 6-1 32 V Note 6-6 -0.3 to IOVCC+0.3 V Note 6-1 -0.3 to IOVCC+0.3 V Note 6-1 6-1：VCC,VSSD must be maintained, VSSD=VSSA=0V 6-2：Make sure VCC≧VSSD, IOVCC≧VSSD 6-3：Make sure VCI≧VSSA 6-4：Make sure VLCD≧VSSA 6-5：Make sure VSSA≧VCL 6-6：Make sure VGH≧VSSA and VSSA≧VGL The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:7 PO023OX1 7. Electrical Characteristics： 7-1 Operation condition： VSS=GND=0V , Ta = 25℃ Value Unit Remark V Note 7-1 3±0.2 Item Power supply voltage (1) Symbol VCI-VSS Power supply voltage (2) VLCD-VSS 4.63 V Power supply voltage (3) VSS-VCL 2.67 V Power supply voltage (4) VLCD-VCL 7.3 V Power supply voltage (5) VGH-VSS 13.7 V Power supply voltage (6) VSS-VGL 10.21 V TFT Common Electrode Voltage VCOMH 3. 6 V VCOML -0.71 V Coupling voltage Δ Vp 0.82 V Black of Video Low Voltage VLB 0.24 V Black of Video High Voltage VHB 4.24 V White of Video Low Voltage VLW 0.2 V White of Video High Voltage VHW Note 7-2 Note 7-3 V 4.18 Note 7-1：The VCI 3±0.2V is base on item 11-2 setting, if out of range, will be have some display abnormal Note 7-2：VCOM must be adjusted optimize display quality, crosstalk, contrast ration and etc. Note 7-3： The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:8 PO023OX1 7-2 Power consumption： Parameter Symbol Min Supply voltage of LED backlight VLED Supply current of LED backlight ILED Backlight Power Consumption PLED Note 7-4：The ILED=150 mA (Constant current) Note 7-5：LED B/L applied information Note 7-6：PLED = VLED* ILED Parameter Supply current for source driver and gate driver Backlight Power Consumption Total power consumption TYP 150 - MAX Unit V (7.6) mA 1140 mW Remark Note 7-4 Note 7-5 Note 7-6 Symbol Conditions TYP. MAX. Unit Remark ICI VCI ＝3.0V 11.7 17.6 mA PLED - - 1140 mW - - - 1192.8 mW 8. Pixel Arrangement： The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:9 PO023OX1 9. Block Diagram： D15~D0 16 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:10 PO023OX1 10. Timing specification： 10-1. 80-system Bus Operation： 10-2. AC Characteristics： 10-2.1 80-system Bus Interface Timing Characteristics： Table.10-2.1 80-System Normal Write Mode (HWM =0)/ (VCI=3V) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:11 PO023OX1 11. Interface specification： 11-1. 16-bit bus interface： The 80-system 16-bit bus parallel data transfer can be used by setting M3-0 pins to “ 0010” . Figure.11-1-2 A Example of 80-System 16-bit Interface Figure.11-1-2 B Data Format of 16-bit bus System Interface The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:12 PO023OX1 11-2. Display on Flow： The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:13 PO023OX1 12. Optical Characteristics： Ta=25℃ Parameter Viewing Angle Symbol Horizontal Ө11、Ө12 Ө22 Vertical Ө21 Condition MIN. TYP. MAX. Unit Rem arks CR≥ 10 70 45 65 75 50 70 - deg deg deg Note 12-1 200 400 - - Note 12-2 Contrast Ratio CR At optimized view angle Brightness L θ =0° 800 1000 Uniformity U% θ =0° 70 75 - % θ =0° - 15 20 20 30 0.29 0.33 0.37 ms ms - 0.31 0.35 0.39 - - hrs Response time Rise Fall White Chromaticity LED Life Time Tr Tf x θ =0° y +25℃ - 20000 30000 cd/㎡ Note 12-4 Note 12-5 Note 12-3 Note 12-6 Note 12-1: The definitions of viewing angles are as follow Ө12 Ө21 Ө22 Ө11 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:14 PO023OX1 Note 12-2: The definition of contrast ratio： CR = Luminance at White Pattern Luminance at Black Pattern Note 12-3: Definition of Response Time Tr and Tf： W hite Black W hite 100% 90% Brightness 10% 0% Tr Tf Note 12-4: All optical measurements shall be performed after backlight being turned-on for 30 mins. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure. Photometer (TOPCON BM-5A or BM-7 fast) 500 mm +/- 50 mm Field = 1° TFT-LCD Optical characteristics measuring configuration The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:15 PO023OX1 Note 12-5：The uniformity of LCD is defined as U = The Minimum Brightness of the 9 testing Points The Maximum Brightness of the 9 testing Points Luminance meter：BM-5A or BM-7 fast (TOPCON) Measurement distance：500 mm +/- 50 mm Ambient illumination：< 1 Lux Measuring direction：Perpendicular to the surface of module The test pattern is white. Note 12-6：The “ LED Life time “ is defined as the module brightness decrease to 50% original Brightness that the ambient temperature is 25℃ and ILED = 150mA. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:16 PO023OX1 13. Handling Cautions： 13-1) Mounting of module： a) Please power off the module when you connect the input/output connector. b) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. c) Protective film (Laminator) is applied on surface to protect it against scratches and dirt. d) Please following the tear off direction as figure 13-1 to remove the protective film as slowly as possible, so that electrostatic charge can be minimized. 13-2) Precautions in mounting： a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 13-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 13-4) Others： a) Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. As open the packing, must assembly within 3 month c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. 13-4) Polarizer mark： The polarizer mark is to describe the direction of wide view angle film how to mach up with the rubbing direction. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:17 PO023OX1 Figure 13-1 the way to peel off protective film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:18 PO023OX1 14. Reliability Test： No Test Item Test Condition 1 High Temperature Storage Test Ta = 85℃, 240 hrs 2 Low Temperature Storage Test Ta = -40℃, 240 hrs 3 High Temperature Operation Test Remark Ta = 80℃, 240 hrs 4 Low Temperature Operation Test Ta = -30℃, 240 hrs 5 High Temperature & High Humidity Operation Test Ta = 60℃, 95%RH, 240 hrs (No Condensation) 6 Thermal Cycling Test (non-operating) 7 Vibration Test (non-operating) 8 Shock Test (non-operating) 9 Electrostatic Discharge Test (non-operating) -30℃ Æ +80℃, 200 Cycles 30 mins 30 mins Frequency : 10 ~ 55 HZ Amplitude : 1 mm Sweep time : 11 mins Test Period : 6 Cycles for each direction of X, Y, Z 100G , 6ms Direction : ±X , ±Y , ±Z Cycle : 3 times 200pF , 0Ω ±200V 1 time / each terminal Ta：ambient temperature [Criteria] In the standard conditions, there is not display function NG issue occurred. (including：line defect ,no image)All the cosmetic specification is judged before the reliability stress. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:19 PO023OX1 15. Packing： 摺口袋 450*380*700mm 抗靜電 抗靜電 抗靜電 需180交叉堆疊，疊堆後可從側邊檢視圓弧防 呆方向是否正確 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:20