SPECIFICATION FOR APPROVAL REF. : SP1206□□□□L□-□□□ ABC'S DWG NO. PROD. Shielded SMD Power Inductor NAME REV. 20130503-A PAGE 1 Ⅰ﹒Configuration and dimensions： 5.70±0.30 1.90±0.20 12.50±0.30 12.50±0.30 7.50±0.25 2.00 ref. 5.20 ref. 3 ：CLIP 3 For mounting fixed 2 3.75 ref. 4.15 ref. 10.50 ref. 1 4.50 ref. 2.50 nom. 3.00 ref. 7.50 ref. 2.00 ref. 4.70 ref. 4.15 ref. 13.00 ref. ( PCB Pattern ) 6.40 ref. Ⅱ﹒Schematic diagram： 1 2 Ⅲ﹒Description： a﹒Ferrite ER core construction. b﹒Magnetically shielded. c﹒Enamelled copper wire：F class Peak Temp：245℃ max. Max. Peak Temp - 5℃：30sec max. Max time above 217℃ ：60sec~150sec max. d﹒Product weight： 3.10 g（ref.） e﹒Moisture sensitivity Level 1 Temperature Rising Area f﹒Products comply with RoHS' requirements Preheat Area +4.0℃ / sec max. g﹒Halogen free available 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +3.0℃ / sec max. -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 245℃ 250 Ⅳ﹒General specification： a﹒Storage temp.：-40℃ ----+125℃ b﹒Operating temp.：-40℃----+125℃ (Temp. rise included) c﹒Resistance to solder heat：245℃.10 secs. AR-001C Temperature ( ℃ ) 217℃ 60sec~150sec 200 60sec max. 150 60sec~120sec 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF. : SP1206□□□□L□-□□□ ABC'S DWG NO. PROD. Shielded SMD Power Inductor NAME REV. 20130503-A PAGE 2 Ⅴ﹒Electrical characteristics： Initial Inductance L0 ( uH ) Inductance at flat point L1 ( uH ) Irms Isat (A) (A) DC Resistance max. ( mΩ ) SP1206R47YL□-□□□ 0.70±25% 0.47±25% 5.0 30.0 30.0 2.3 SP1206R60YL□-□□□ 0.90±25% 0.60±25% 5.0 28.0 26.0 2.3 SP1206R80YL□-□□□ 1.10±25% 0.80±25% 5.0 26.0 25.0 3.2 SP12061R3YL□-□□□ 1.50±25% 1.30±25% 4.0 22.0 19.0 3.6 SP12062R0YL□-□□□ 2.20±25% 2.00±25% 4.0 17.0 15.0 6.0 SP12062R8YL□-□□□ 3.00±25% 2.80±25% 3.0 15.0 13.0 7.0 DWG No. ：Packaging information： 1). 2). "- □□□"：Reference code Flat point ref. (A) Code 3). Electrical specifications at 25℃ 4). Inductance Test Freq.：100KHz / 1V 5). Irms base on Temp. rise 40℃ max. 6). Isat base on inductance drop 20% typ. of L1 value @ Inductance VS. DC Superposition Characteristics Inductance ( uH ) 3.0 2.0 2R8 2R0 1R3 1.0 R80 0 20 10 DC Current ( A ) AR-001C 30 SPECIFICATION FOR APPROVAL REF. : SP1206□□□□L□-□□□ ABC'S DWG NO. PROD. Shielded SMD Power Inductor NAME REV. 20130503-A △℃ R60 PAGE 3 @ DC Current VS Temperature Rise △℃ R47 100 100 75 75 50 50 25 25 0 0 0 10 △℃ 20 30 40 A 10 △℃ R80 100 100 75 75 50 50 25 25 0 20 30 40 A 30 40 A 30 40 A 1R3 0 0 10 △℃ 20 30 40 A 0 10 △℃ 2R0 100 100 75 75 50 50 25 25 20 2R8 0 0 0 AR-001C 0 10 20 30 40 A 0 10 20 SPECIFICATION FOR APPROVAL REF. : SP1206□□□□L□-□□□ ABC'S DWG NO. PROD. Shielded SMD Power Inductor NAME REV. 20130503-A PAGE 4 Ⅵ﹒Packaging information： ( 1 ) Configuration T Cover Tape A B N 2.0±0.5 ∮C ∮C D G Embossed Carrier ※Carrier Tape Width : D P:16 m/m 4 m/m End Start Leader no component 200 m/m min. Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 13 - 24 330 B 21±0.8 C D 13±0.5 24 G 26 +0 N 60 T -0 30.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Code B AR-001C Q'TY (pcs) 600 G.W. (gw) 2,150 Outer : Carton Style 13 - 24 Q'TY (pcs) 2,400 G.W. (Kg) 11.30 Size (cm) 38 x 37 x 22 SPECIFICATION FOR APPROVAL REF. : ABC'S DWG NO. PROD. Shielded SMD Power Inductor NAME REV. SP1206□□□□L□-□□□ 20130503-A PAGE 5 Ⅶ﹒Reliability test： Item 1.High Temperature Exposure Reference documents MIL-STD-202 Method 108 Test Condition 1.Temperature: 125℃ 2.Time:96 hours. 1.Temperature: -40℃ ~ 125℃ 2.Temperature Cycling JESD22 Method JA-104 2.Number of cycle:96 cycle 3.Dwell time:30 minutes 3.Biased Humidity Test MIL-STD-202 Method 103 1.Temperature: 85±5 ℃ 2.Time:96 Hours 3.Humidity: 85±5% RH. 1.Temperature: 125℃ 2.Time:96 hours. 3.Apply rated current. 4.Operational Life MIL-PRF-27 5.Exeternal Visual MIL-STD-883 Method 2009 constructions, marking and Inspect product workmanship. Test Specification 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 1.No pollution on the surface of products. 2.Clear marking. 3.No crack. 6.Physical Dimensions JESD22 Method JB-100 Verify physical dimensions to the applicable product detail specification. Per product specification standard 7.Resistance to solvents MIL-STD-202 Method 215 Immerse into solvent for 3±0.5 minutes & brush 10 times for therr cycles. 1.No body change in apperarance. 2.No marking blurred. 3.Inductance shall not change more than ±25%. 8.Vibration Test MIL-STD-202 Method 204 1.Frequency and Amplitued : 10-2000-10 Hz, 1.5 mm. 2.Direction:X, Y, Z 3.Test duration:2 hours for each direction, 6 hours in total. 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 9.Resistance To Soldering Heat Test MIL-STD-202 Method 210 1.Highest temperature： 245±5℃ 2.Time（temp.≧ 217℃）：60~150 Second. 3.IR reflow times：3 times. 10.Rated current MIL-STD-202 Method 330 11.Temperature rise MIL-PRF-27 12.Over load MIL-PRF-27 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. Apply rated current for 5 second. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. Apply rated current for 10 minutes. 2.Inductance shall not change more than ±25%. 1.No mechanical and electrical damage. Apply twice as rated current for 5 minutes. (It's not application to some special design) 2.Inductance shall not change more than ±25%. 1.Baking in pre-testing： 155±5℃ / 16Hours±30 min. 2.Peak temperature：240±5℃ 3.Time（temp.≧217℃）：60~150 second. 4.IR reflow times：1 times. The terminal shall be at least 95% covered with fresh solder. User Spec. 1.Operating temperature： -40℃~125℃ 2.Room temperature：25℃. 1.No mechanical and electrical damage. 2.Inductance shall not change more than ±25%. MIL-STD-202 Method 201 1.DV:500V 2.Time:1minutes 16.Drop JESD22-B111 Packaged & Drop down from 1m.In 1 angle 1ridges & 2 surfaces orientation. 17.Terminal Strength Test JIS-C-6429 1.Apply push force to samples mounted on PCB. 2.Force of 1.8 kg for 60±1 seconds. 13.Solderability Test 14.Electrical Characteriazation 15.Withstanding Voltage Test AR-001C J-STD-002 1.During the test no breakdown. 2.The characteristic is normal after test. 1.No case deformation or change in appearance. 2.Inductance shall not change more than ±25%. After test, inductors shall be no mechanical damage.