CHIP COMMON MODE CHOKE COIL HDC0504ST SERIES Introductions The HDC0504ST series is wire wound type Common Mode Choke Coil which provides high effective suppression characteristics without distorting the wave pattern of high speed differential signal interface. It is suitable for super high speed differential signal such as USB 3.0, HDMI and so on. Features ＊Cut off frequency in differential mode is 8~10GHz ＊ Operating temperature -40°C to +105°C. ＊ Excellent solderability and resistance to soldering heat. ＊ Suitable for flow and reflow soldering. ＊ Good dimensions, high reliability, and easy surface mount assembly. Part Number HDC 0504 S T 600 -S 1 2 3 4 5 6 1 Chip Common Mode Choke Coil 2 Chip Size CODE L W H UNIT EIA 0.047 0.039 0.035 Inch JIS 1.20 1.00 0.90 mm 3 General Characteristics 4 Taped In Reel. 3,000pcs/reel. 5 Typical Impedance at 100MHz 600 = 60 Ω Material Structure Ferrite Copper Wire Gold (Au) Termination 87 COMMON MODE HDC0504ST SERIES 6 S = USB 3.0 H = HDMI COMMON MODE CHOKE WIRE WOUND TYPE 0.9 max. 0.03mm (ref.) DIMENSION AND CONFIGURATION 0.35 ± 0.1 0.35 ± 0.1 1.00 ± 0.2 0.3 ± 0.1 0.35 ± 0.1 Remark : : Electrode ( ) : Reference Value Unit : m/m 1.20 ± 0.2 0.4 0.3 1.10 (1) (2) (4) (3) 0.4 0.45 0.65 0.45 1.55 RECOMMENDED PCB PATTERN NO POLARITY ELECTRICAL SPECIFICATION HDC0504 SERIES Part Number Common Mode Impedance (Ω) at 100MHz Cut-off Freq. (GHz) DC Resistance max ( ) Rated Current (mA) Rated Voltage (V DC) Insulation Resistance min (M ) Cut-off Frequency (GHz) HDC0504ST600-S 60 typ. (43 min) 10.0 0.40 max. 300 20 max. 100 min 10 typ. HDC0504ST900-H 90 typ. (65 min) 10.0 0.50 max. 280 20 max. 100 min 8 typ. 1. Impedance is measured in HP4287A at frequency of 100MHz. 2. For 15 °C rise. 88 COMMON MODE CHOKE COILS HDC0504 (S) SERIES INSERTION LOSS Avgs=2 130 Y:Ω Choke impedance Graphic result Frequency (MHz) 1 120 Points=1024 Sys Risc: 50 ps, Date: 2010/05/21 16:12:43 10 100 1000 10000 0 Max 110 90 80 70 Insertion Loss (db) 100 1 Min 2 60 50 Base:40.5372 ns 3 Scale:200.0 ps/div Ver:3.23 Parameter Name:Choke Impedance C1 Spc Max: 105 Ω Spc Min: 75 Ω Max: 102.64 Ohms at 41.7752 ns Min: 87.85 Ohms at 41.2612 ns ∆Ω:14.79 Avg: 95.24 Ohms Result:Pass USB3.0 Eye Graphic result 750 Date: 2010/11/11 20:12:42 , Resolution: 500x400 pixels 0 -750 Wfrms=500 Base:27.9743ns Scale:33.0 ps/div Parameter Name:USB3.0 Eye Aoba Display Mode:USB3.05Gpbs dRate: 5 Gbits/s ; 200.0 ps V: 400 mV ; Gain: 0 dB ; Off: 0 mV JGen:OFF Result:pass 89 Ver:3.26 COMMON MODE CHOKE COILS HDC0504ST (S) SERIES INSERTION LOSS Frequency (MHz) 1 10 100 Insertion Loss (db) 0 1 2 3 90 1000 10000 COMMON MODE CHOKE WIRE WOUND TYPE RELIABILITY SPECIFICATION 1 Scope This specification applies to wired wounded chip common mode choke of the following types used in electronic equipment : ＊Material : Ferrite 2 Construction ＊Configuration & Dimension : Please refer to the attached figures and tables. ＊Terminals : HDC0504 (S) series shall consist of Ag followed by Nickel, then Gold (Au) plating. 3 Operating Temperature Range Operating Temperature Range is the scope of ambient temperature at which the common mode choke can be operated continuously at rated current. ＊Temp. Range : - 40 °C to + 85 °C 4 Recommended Soldering Conditions Peak : 250 +5/-0°C 230°C or higher 2 to 6°C/s 180°C 3 to 6°C/s Pre-heating Zone 150°C 90 ± 30s 30 ± 10s 2 to 4°C/s Soldering Zone Heating Time 5 Characteristics Standard Atmospheric Conditions Unless otherwise specified, the standard range of atmospheric conditions for making measurements and tests are as follows : ＊Ambient Temperature : 25°C ± 2 °C ＊Relative Humidity : 60% to 70% (RH) ＊Air Pressure : 86 Kpa to 106 Kpa 91 COMMON MODE CHOKE WIRE WOUND TYPE RELIABILITY SPECIFICATION CONDITION ITEM Electrical Characteristics SPECIFICATION Ω Ω Common Mode Impedance (Zc) and Tolerance Measuring Equipment : HP-4287A or equivalent. Measuring Frequency : 100 ± 1MHz Measuring Temperature : 25 ± 5°C (Refer to Measurement Diagram ) Minimum 43 Insulation Resistance Measuring Voltage : Rated Voltage Measuring Time : 1 minute max. (Refer to Measurement Diagram ) 100 MΩ minimum Dielectric Withstanding Voltage Test Voltage : 2.5 times to Rated Voltage Time : 1 to 5 seconds. Charge current : 1mA max. (Refer to Measurement Diagram ) No damage occurs when the test voltage is applied. Test Current : Rated Current (Refer to Measurement Diagram ) Temperature Rise : ≤ 15°C Measured with current of 100mA max. In case of doubt, measured by four terminal method. (Refer to Measurement Diagram ) Within Specified Tolerance. Rated Current DC Resistance (RDC) Pressig jig Warp = 2mm Pressing Speed = 0.5mm/sec Duration = 5 ± 1 sec 20 10 R340 Flexure Strength (1-1mm) . Typical : 50~60 . Table 1. Change In Appearance Without distinct damage Board Change In Common Mode Impedance : Within ± 20% R5 45 ± 2mm 45 ± 2mm Drop Test Components shall be dropped three times on a concrete or steel board at height of 1 M naturally at any directions. Insulation Resistance : Vibration (Random) Components shall be randomly vibrated at amplitude of 1.5mm and frequency of 10 - 55 Hz : 0.04 G / Hz, 1 minute at a period of 2 hours in each of the three mutually perpendicular directions. Withstanding Voltage : No damaged Solderability Dip pads in flux and then in a solder bath at 240 °C ± 5°C for 5 seconds. A minimum of 80% of the metalized area must be covered with new solder. Meet Table 1. Resistance to Soldering Heat Preheat components at 80 to 120 °C for 1 minute. Dip components into flux and then into a melted solder bath at 255 ± 5°C for 5 ± 1 seconds. Then components are to be tested after 4-48 hours at room temperature. Mechanical Characteristics 92 Ω 10M min COMMON MODE CHOKE WIRE WOUND TYPE RELIABILITY SPECIFICATION ITEM Endurance Characteristics CONDITION SPECIFICATION Cold Temperature Storage Table 1. Components shall be stored at temperature of Change In Appearance -40 °C ± 2 °C for 1000 (+48 hours -0 hour). Without distinct damage Then components shall be subjected to standard atmospheric conditions for 4-48 hours. After that, measurement shall be made. High Temperature Storage Change In Common Mode Components shall be stored at temperature Impedance: of +85 °C ± 2 °C for 1000 (+48 hours -0 hour). Within ± 20% Then components shall be subjected to standard atmospheric conditions for 4-48 hours. After that, measurement shall be made. Moisture Resistance Components shall be stored in the chamber at 40 °C at 90 - 95% R. H. for 1000 (+48 hours -0 hour). Then components are to be tested after 4-48 hours at room temperature. Temperature Cycle Each cycle shall consist of 30 minutes at -40°C followed by 30 minutes at 85°C with a 10-15 minutes maximum transition time between Withstanding Voltage: temperature extremes. Test duration is 100 cycles, No damaged then components are to be tested after 4-48 hours at room temperature. Components shall be stored at temperature of +85 °C ± 2 °C for 1000 (+48 hours -0 hour) with rated current applied. Then components shall be subjected to standard (Rated Current) atmospheric conditions for 4-48 hours. After that, measurement shall be made. High Temperature With Loaded 93 Insulation Resistance: Ω 100M min COMMON MODE CHOKE WIRE WOUND TYPE RELIABILITY SPECIFICATION Measurement Diagram Terminal to be Tested When measuring and supplying the voltage, the following terminal is applied. No. ITEM 1 Common Mode Impedance ( Measurement Terminal ) 2 Withstanding Voltage ( Measurement Terminal ) 3 DC Resistance ( Measurement Terminal ) 4 Rated Current 5 Insulation Resistance Terminal to be Tested Terminal Terminal Terminal Terminal Terminal Terminal Terminal 94 Terminal PACKAGING INFORMATION Packing Quantity TYPE PCS / REEL HDC0504 3,000 Ø60 Ø178 1.0 A B HDC0504 F K T 0.98 0.23 ± 0.10mm Tolerance 1.16 1.41 4.00 Ø1.5 +0.1 -0 Tape Thickness Insert Pitch (Ø0.059 +0.004 ) -0 4±0.1 2±0.1 (0.157±0.004) (0.079±0.004) 8±0.3 (0.314±0.012) TYPE Chip Cavity K T B Dimensions (unit:m/m) 3.5±0.05 1.75±0.1 (0.138±0.002) (0.069±0.004) 9.0 A 4±0.1 (0.157±0.004) TAPE DIRECTION Blank Portions Chip Cavity Top Tape Strength The top tape requires a peel-off force of 0.2 to 0.7N in the direction of the arrow as illustrated below Leader Top Tape 0 ~ 15° o 160mm min 80mm min Direction of tape feed Base Tape 95