SPECIFICATION FOR APPROVAL REF. : SF0905□□□□L□-□□□ ABC'S DWG NO. PROD. SMD Line Filter NAME REV. 20150804-E PAGE 1 Ⅰ﹒Configuration and dimensions: B ABC 100Y Marking Inductance code 0.8±0.2 C A 1.2 1.4 max. 3 E 1.2 2 2.54 1.8 max. F W 1 2.0 9.5 4 (PCB Pattern) Unit:m/m A B C E F W 9.20 ±0.3 6.00 ±0.3 5.00 ±0.3 2.54 ±0.2 5.70 ref. 1.00 ±0.1 Ⅱ﹒Schematic diagram: N2 2 3 1 " N1 " : Polarity 4 Ⅲ﹒Description: a﹒Ferrite toroidal core construction. Peak Temp:250℃ max. Max. Peak Temp - 5℃:30sec max. Max time above 217℃ :60sec~150sec max. b﹒Enamelled copper wire:H class Temperature Rising Area c﹒Product weight: 0.42g(ref.) Preheat Area +4.0℃ / sec max. d﹒Moisture sensitivity Level 1 e﹒Products comply with RoHS' requirements 250 f﹒Halogen free available 200 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +3.0℃ / sec max. -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 250℃ Ⅳ﹒General specification: a﹒Storage temp.:-40℃ ----+105℃ b﹒Operating temp .:-40℃----+105℃ Temperature ( ℃ ) 217℃ 60sec~150sec 60sec max. 150 60sec~120sec 100 50 (Temp. rise included) c﹒Resistance to solder heat:250℃.10 secs. AR-001C 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF. : SF0905□□□□L□-□□□ ABC'S DWG NO. PROD. SMD Line Filter NAME 20150804-E REV. PAGE 2 Ⅴ﹒Electrical characteristics: DC Nominal Resistance Voltage N1,N2 ( Ω ) Vdc ( V ) DWG. No. Indductance L1 , L2 ( μH ) Test condition SF0905100YL□-□□□ 10±30% 0.1V,1kHz 0.08 max. 80 1.6 200 min. 20 ~ 300 SF0905250YL□-□□□ 25±30% 0.1V,1kHz 0.16 max. 80 1.0 600 min. 20 ~ 150 SF0905400YL□-□□□ 40±30% 0.1V,1kHz 0.25 max. 80 0.9 800 min. 20 ~ 100 SF0905500YL□-□□□ 50±30% 0.1V,1kHz 80 0.8 1500 min. 20 ~ 100 80 1.2 600 min. 3 ~ 20 Rated current (A) Impedance (Ω) Freq. Range ( MHz ) SF0905251YL□-□□□ 250±50% 5mV,100kHz 0.32 max. 0.13 max. SF0905471YL□-□□□ 470±50% 5mV,100kHz 0.14 max. 80 1.1 1000 min. 2 ~ 20 SF0905501YL□-□□□ 500±50% 5mV,100kHz 0.15 max. 80 1.0 1000 min. 1 ~ 20 SF0905102YL□-□□□ 1000±50% 5mV,100kHz 0.31 max. 80 0.8 1500 min. 1 ~ 15 SF0905202YL□-□□□ 2000±50% 5mV,100kHz 0.42 max. 80 0.6 3000 min. 1~ SF0905472YL□-□□□ 4700±50% 5mV,100kHz 0.90 max. 80 0.4 4000 min. 0.3 ~ 3 SF0905652YL□-□□□ 6500±50% 5mV,100kHz 1.05 max. 80 0.3 5000 min. 0.3 ~ 2 :Packaging information: 1). 2). "- Code □□□ ":Reference code 3). Electrical specifications at 25℃ 4). Irms base on Temp. rise 45℃ max. 5). HI-Pot test ( N1-N2 ) :500Vac / 60Hz , 3mA , 3sec. Ⅵ﹒Curve: 7 7 5 500Y 400Y 5 472Y 3 471Y 501Y Impedance ( KΩ) Impedance ( KΩ) 1 100Y 0.7 0.5 0.3 Impedance ( KΩ) 102Y 3 250Y 652Y 20 202Y 251Y 1 0.7 10 8 5 2 1 0.5 0.3 0.1 0.3 1 3 10 Frequency ( MHz ) 0.1 1 3 10 30 100 Frequency ( MHz ) 300 Measuring circuit : 0.1 0.3 1 3 10 30 100 Frequency ( MHz ) RF Impedance AR-001C 30 100 5 SPECIFICATION FOR APPROVAL REF. : SF0905□□□□L□-□□□ ABC'S DWG NO. PROD. SMD Line Filter NAME REV. 20150804-E PAGE 3 Ⅶ﹒Packaging information: ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:12 m/m 4 m/m End Start ABC 100Y ABC 100Y ABC 100Y ABC 100Y ABC 100Y ABC 100Y Leader no component 200 m/m Min. Trailer no component 400 m/m Min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 13 - 16 330 B 21±0.8 C D 13±0.5 16 G 18 +0 N 50 -0 T 22.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Code B AR-001C Outer : Carton Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) 1,000 860 13 - 16 6,000 G.W. (Kg) 6.5 Size (cm) 38 x 37 x 22 SPECIFICATION FOR APPROVAL REF. : SF0905□□□□L□-□□□ ABC'S DWG NO. PROD. NAME SMD Line Filter REV. 20150804-E PAGE 4 Ⅷ﹒Reliability test: Item 1.High Temperature Exposure Reference documents MIL-STD-202 Method 108 2.Temperature Cycling JESD22-A 104 3.Biased Humidity Test MIL-STD-202 Method 103 Test Condition 1.Temperature: 105±2℃ 2.Time:96±2 hours. 1.Temperature: -40℃ ~ +105℃ 2.Number of cycle:100 cycle 3.Dwell time:30 minutes 1.Temperature:85±2 ℃ 2.Humidity: 85% RH. 3.Time:96±2 Hours 1.Temperature: 105℃ (Temp. rise included) 2.Time:96±2 hours. 3.Rated current 4.Operational Life JESD22-A 108 5.External Visual JESD22-B 101 & Inspect product constructions, marking and MIL-STD-883 Method 2009 workmanship. 6.Physical Dimensions JESD22-B 100 7.Resistance to solvents MIL-STD-202 Method 215 Test Specification 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 1.No pollution on the surface of products. 2.Clear marking. 3.No crack. Verify physical dimensions to the applicable product detail specification. Per product specification standard Immerse into solvent for 3±0.5 minutes & brush 10 times for 3 cycles. 1.No body change in apperarance. 2.No marking blurred. 3.Inductance shall not change more than ±50%. 1.Frequency and Amplitued : 10-2000-10 Hz, 1.5 mm. 2.Direction:X, Y, Z 3.Test duration:2 hours for each direction, 6 hours in total. 1.Highest temperature:250±5℃. 2.Time(temp.≧ 217℃):60~150 Second. 3.IR reflow times:3 times. 1.Applied one and half rated current for a period of 5 minutes. 2.Rated current 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 8.Vibration Test MIL-STD-202 Method 204 9.Resistance To Soldering Heat Test MIL-STD-202 Method 210 & J-STD020D.1 10.Over load JIS C 6436 & User SPEC. 11.Temperature Rise Current JIS C 6436 & User SPEC. 1.Applied rated current for 10 minutes. 2.Temperature measure by digital surface thermometer. 3.Irms current Surface temperature rise is less than 45℃ max. 12.Solderability Test J-STD-002 & JESD22-B 102 1.Baking in pre-testing: 150±5℃ / 16Hours±30 min. 2.Peak temperature:240±5℃ 3.Time(temp.≧217℃):60~150 second. 4.IR reflow times:1 times. More than 95% soldering coverage min on terminations. 13.Electrical Characteriazation MIL-STD-202 Method 304 & User SPEC. 1.Operating temperature:-40℃~105℃ 14.Withstanding Voltage Test MIL-STD-202 Method 301 & User SPEC. 1.DC: 500 V (Winding to Winding) 2.Time: 3sec. 15.Drop 1.Products shall be mounted on SPEC. PCB and dropped down from a height of 1m CNS-C6354 & GB/T 2423.8 2.Drop total time:6 time (Every side of sample drop 2 time) 16.Terminal Strength Test IEC 60068-2-21 AR-001C 2.Room temperature:25℃. 1.Apply push force to samples mounted on PCB. 2.Force of 1.8 kg for 60±1 seconds. 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. No electrical or mechanical damage 1.No mechanical or electrical damage. 2.Inductance shall not change more than ±50%. 1.During the test no breakdown. 2.No mechanical or electrical damage. 1. Adhesion on PCB shall be enough. 2. Product appearance shall not break. 3. No electrical damage. After test, inductors shall be no mechanical damage.