1/4 z Structure Silicon Monolithic Integrated Circuit z Product Name Step-up DC/DC converter for medium size LCD panel z Type BD6586MUV z Features High efficiency PWM step-up DC/DC converter (fsw=1MHz) High accuracy and good matching current driver 4ch Drive up to 6 in series × 4 strings in parallel =24white LEDs (*white LED Vf=4.0Vmax) o zAbsolute maximum ratings (Ta=25 C) Parameter Symbol Limits Unit Condition Maximum applied voltage 1 VMAX1 7 V VBAT, EN1, EN2, TRSW, PWM, TESTO, ISET, TEST Maximum applied voltage 2 VMAX2 25 V LED1, LED2, LED3, LED4, Maximum applied voltage 3 VMAX3 30.5 V SW Maximum applied voltage 4 VMAX4 50.5 V VDET Power dissipation 1 Pd1 500 mW *1 Power dissipation 2 Pd2 780 mW *2 Power dissipation 3 Pd3 1510 mW *3 Operating temperature range Topr -40 ~ +85 o C - Tstg -55 ~ +150 o C - Storage temperature range o o (*1) It will be reduced every 4.0mW/ C (Ta>25 C) when it’s not mounted on a heat radiation Board. (*2) it will be reduced every 6.2mW/oC (Ta>25oC) when It’s not mounted on 1 layer board (ROHM Standard board) and Copper foil area 0mm2 (*3) It will be reduced every 12.1mW/oC (Ta>25oC) when it’s mounted on 4 layer board (JEDEC Compliant board) and Copper foil area 6.28mm2 on 1st layer and Copper foil area 5655.04mm2. 2nd-4th layer. zOperating conditions (Ta=-40 to +85oC) Parameter Supply voltage Symbol VBAT Min. Rating Typ. Max. 2.7 ~ 5.5 Unit Condition V This product isn’t designed to protect itself against radioactive rays. Status of this document The English version of this document is the formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document, formal version takes priority. Application example ▪ ROHM cannot provide adequate confirmation of patents. ▪ The product described in this specification is designed to be used with ordinary electronic equipment or devices (such as audio-visual equipment, office-automation equipment, communications devices, electrical appliances, and electronic toys). Should you intend to use this product with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. ▪ ROHM assumes no responsibility for use of any circuits described herein, conveys no license under any patent or other right, and makes no representations that the circuits are free from patent infringement. Rev.A 2/4 zElectrical Characteristics o (Unless otherwise noted, VBAT=3.6V, Ta = +25 C) Parameter Symbol Min. Spec Typ. Max. - 0.4 Unit Condition EN1, EN2, PWM Pin Low Input Voltage range VthL 0 High Input Voltage range VthH 1.4 - 5.5 V Iin - 8.3 16.0 µA Input voltage=2.5V V VBAT falling edge Input current UVLO Under Voltage Lock Out V UVLO 2.05 2.35 2.65 Switching Regulator Quiescent Current Iq - 0.1 2.0 µA EN1=EN2=PWM=0V Current Consumption Idd - 2.2 4.6 mA VDET=0V,ISET=24kΩ LED Control voltage VLED 0.4 0.5 0.6 V Over Current Limit Ocp 1.1 1.5 2.5 A *1 SBD Open Protect Sop - - 0.1 V Detect voltage of VDET pin Switching frequency fSW 0.7 1.0 1.3 MHz Duty cycle limit Duty 91 95 99 % LED1-4=0.3V Over Voltage Limit Ovl 25.0 25.5 26.0 V LED1-4=0.3V RSW - 0.24 0.32 Ω Isw=100mA Current driver LED maximum current ILMAX - - 25 mA LED current accuracy ILACCU - - ±5 % ILED=20mA % ▪Each LED current/Average (LED1- 4 current) SW Transistor On Resistance LED current matching ILMAT - - ±3 ▪ILED=20mA ISET voltage LED current limiter LED Terminal Over Voltage Protect Iset 0.5 0.6 0.7 V ILOCP 35 60 90 mA LEDOVP 10.0 11.5 13.0 V *1. This parameter is tested with dc measurement Rev.A ISET resistance 4.7kΩ LED1- 4 =0.5V EN1=EN2=PWM=2.5V 3/4 zPackage outline drawing zTerminals Type D6586 LOT No. (VQFN024V4040) (Unit : mm) PIN PIN Name 1 VBAT 2 EN1 3 EN2 4 GND 5 PWM 6 ISET 7 GND 8 LED1 9 LED2 10 GND 11 LED3 12 LED4 13 TEST 14 TESTO 15 N.C. 16 SW 17 SW 18 SW 19 VDET 20 N.C. 21 PGND 22 PGND 23 N.C. 24 TRSW zBlock diagram VBAT EN1 EN2 SBD OPEN/ Output short PROTECT TSD VDET Reference UVLO Output Over Voltage PROTECT + TRSW LED TERMINAL OPEN/SHORT DETECTOR SW SW Soft start SW ERRAMP Pulse Control LED1 - PWM COMP + LED2 LED RETURN SELECT + LED3 LED4 + OSC Current SENCE 4ch PGND + - PGND ISET Resistor driver N.C. GND TEST TESTO N.C. N.C. PWM ISET Current Driver GND Rev.A GND 4/4 zCautions on use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Power supply and GND line Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. Pay attention to the interference by common impedance of layout pattern when there are plural power supplies and GND lines. Especially, when there are GND pattern for small signal and GND pattern for large current included the external circuits, please separate each GND pattern. Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same time, in order to use a capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (3) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient. (4) Short circuit between terminals and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power supply or the GND terminal, the ICs can break down. (5) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (6) Input terminals In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. And, as the unused input terminals may make unstable state occur in the internal circuit, please connect them to I/O GND. (7) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (8) Thermal shutdown circuit (TSD) When junction temperatures become 175°C (typ) or higher, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (9) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. (10) DC/DC converter Please select the low DCR inductors to decrease power loss for DC/DC converter. Rev.A Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0