S/MON/SAL965460/C/10/02/2009 celpac page 1 / 6F/GB PRELIMINARY 输出／ＯＵＴＰＵＴ：２４－６００ＶＡＣ ３２Ａ （＊） 功 率 固 态 继 电 器 Power Solid State Contactor ❏ SAL965460 输入／ＩＮＰＵＴ：３．５Ｖ－３２ＶＤＣ Install it & Forget it! 采用节省空间设计，厚度为２２．５ｍｍ的固态接触器． 带散热器． 被设计专门用于电阻性负载的过零触发固态接触器． 22,5mm Solid State Contactor for space-saving design. Ready to use with its heatsink Zero Cross Solid State Contactor specially designed for resistive loads. 2 ❏ 为了预期的长的寿命，采用了使用ＴＭＳ 技术的新的高效能背对背闸流管 (*) ＳＣＲ额定值为：２４－６００ＶＡＣ ５０Ａ． 电流限制器（２２／３２Ａ）根据散热器：见降容曲线 New High Efficiency Back to back thyristors on output with TMS2 technology (*) for a long lifetime expectancy: 24 to 600VAC 50A SCR rating . Current limitation (22/32A) by heatsink : see derating curve ❏ 大的控制范围：３．５－３２ＶＤＣ，有电流限制器 输入端由可见的黄色ＬＥＤ指示 输入有过电压保护 Large control range: 3.5-32VDC with input current limiter. Yellow LED visualization on the input. Input over-voltage protection. ❏ SAL965460 = SA965460 SSR + WF311100 heatsink + 1K522000 cover 带有用于ＤＩＮ导轨安装的集成的散热器和ＩＰ２０保护的透明盖． Delivered with integrated heatsink for DIN rail mounting and with IP20 protection cover. ❏ 设计符合标准 ＥＮ６０９４７－４－３（ＩＥＣ９４７－４－３） 和 ＥＮ６０９５０／ＶＤＥ０８０５ （绝缘增强） (*) 22A@ 40°C AC-51 －ＵＣ－ｃＵＬ申请中 见降容曲线／ Designed in conformity with EN60947-4-3 (IEC947-4-3) and EN60950/VDE0805 (Reinforced Insulation) -UL-cUL pending see derating curve 400VAC 尺寸／ 典型应用： ８ＫＷ电阻 （ＡＣ－５１ 负载） ４００ＶＡＣ电压 Dimensions : (*) : Thermo Mechanical Stress Solution Proud to serve you All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis. Typical application: 8kW resistor (AC-51 load) on 400 VAC celduc r e l a i s celpac S/MON/SAL965460/C/10/02/2009 page 2 / 6F/GB 控制特性／ Control characteristics (at 25°C) 控制电压／ Control voltage 控制电流／ Control current (@ Uc ) 释放电压／ Release voltage 输入ＬＥＤ／ Input LED 反向电压／ Reverse voltage 钳位电压／ Clamping voltage (Transil) 输入免疫／ Input immunity : EN61000-4-4 Symbol Uc Ic Uc off Min 3,5 <10 2 14 Unit V mA V jaune / yellow 32 36 2kV 2KV Urv Uclamp 输入免疫 / Input immunity : EN61000-4-5 12 10 Ic(mA) 参数／ Parameter Input : Ic = f( Uc) DC Typ Max 5-12-24 32 <14 <14 8 6 4 V V 2 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Uc (Vdc) (at 25 ° C) 输出特性／ Output characteristics / 参数／ / Parameter 工作电压范围／ Operating voltage range Conditions 峰值电压／ Peak voltage 过零电位／ Zero cross level 门闩电压／ Latching/ voltage 额定电流／ nominal current Ie nom (AC-51) 非重复过载电流／ / Non repetitive overload current 通态电压降／ On state voltage drop tp=10ms (Fig. 3) @ 25°C 通态动态电阻／ On state dynamic resistance 输出消耗功率（最大值）／ Output power dissipation (max value) 连接点到外壳之间的导热电阻／ Thermal resistance between junction to case 断态漏电流 / Off state leakage current 最小负载电流／ Minimum load current 导通时间／ Turn on time 关断时间／ Turn off time 工作频率范围／ Operating frequency range 断态ｄｖ／ｄｔ ／ Off state dv/dt 非重复最大ｄｉ／ｄｔ ／ Maximum di/dt non repetitive I2t (<10ms) 抗传导等级／ Conducted immunity level 抗传导等级／ Conducted immunity level 传导和辐射干扰／ Conducted & emitted interference 短路保护／ Short circuit protection @Ue typ, 50Hz Symbol Ue Up Usync Ua Ie AC-51 Itsm Vt rt Min 24 1200 20 10 see derating curve (page3) 530 580 0,85 7,5 Unit V rms V V V A rms A V mΩ Pd 0,9x0,85xIe + 0,0075 x Ie2 W Rthj/c 0,6 0,75 K/W 1 mA mA ms ms Hz V/µs A/µs A2s Ilk Iemin ton max toff max f dv/dt di/dt I2t @Ue typ, 50Hz @Ue typ, 50Hz F mains 通用特性／ General characteristics (at 25 ° C) 50-60 1404 1680 2kV criterion B 2kV criterion A with external VDR Class A for Industrial applications Example Fuse Ferraz gRC 25A/32A/50A 10/55Hz Half sinus /11ms 抗冲击符合ＩＥＣ６００６８－２－２７／ Shocks withstand according to IEC 60068-2-27 环境温度（无结冰和凝结）／ Ambient temperature (no icing, no condensation) 储存温度（无结冰和凝结）／ Storage temperature (no icing, no condensation) 环境湿度／ Ambient humidity 重量／ Weight 符合／ Conformity 符合／ Conformity 外壳材料／ Housing Material 底板／ Base plate 0,1 500 10 10 800 50 Symbol Ui Ui Ri Uimp 输入和输出绝缘／ Input to output insulation 输出和外壳绝缘／ Output to case insulation 绝缘电阻／ Insulation resistance 额定冲击电压／ Rated impulse voltage / CEI529 保护等级／ Protection level 抗震动１０－５５Ｈｚ ／ Vibration withstand 10 -55 Hz according to IEC 60068-2-6 Max 600 5 IEC/EN61000-4-4 (bursts) IEC/EN61000-4-5 (surge) IEC60947-4-3 voir/see page 5 Typ. 400 HR 4000 VRMS 4000 VRMS 1000 (@500VDC) MΩ 4000 V IP20 (with cover or flaps) 1,5 mm 30 gn -40 /+80 °C -40/+125 °C 40 to 85 % 250 g EN60947-4-3 (IEC947-4-3) EN60950 / UL/cUL PA 6 UL94V0 Aluminium celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 celpac S/MON/SAL965460/C/10/02/2009 page 3 / 6F/GB 热量曲线和散热器的选择／ Thermal curves and heatsink choice 对应于额定负载电流和环境温度，工作周期为１００％的功率损耗曲线（持续电流）／ Power Dissipation curve in compliance with nominal load current and ambient temperature for a duty cycle of 100% ( permanent current). −> 散热器的热阻取决于底板必须垂直安装，ＳＳＲ的限制，箱子的通 风环境（风扇），通常，散热器ＷＦ３１１１００的热阻（Ｒｔｈ）在２Ｋ／Ｗ 到３ＫＷ之间，具体取决于应用和安装． Thermal resistance of heatsink used on this contactor depends on mounting which must be vertical, confinement of the SSR,ventilation (fan) in the cabinet. Generally, thermal resistance (Rth) of this WF311100 heatsink is between 2 à 3 K/W depending on application and installation 热量特性：电流对应环境温度： 曲线“１” 获得产品的极限值．对与元件这个被达到的温度是可接受的．这些数值符合大部分的固态继电器生产商． 在一个箱子中有非常小的通风或一个非持续电流，这些数字是可以接受的． 曲线“２” 给出了产品符合ＥＮ６０９４７－４－３标准，最大温升５０ °C (@40 ° C) ，在静止空气中持续工作的限定值．（连续试验８小时） 对非持续电流，你可以计算平均功率＝Ｐｄ＊任务周期，核对温升：Ｔｊ＝Ｐｄ＊Ｒｔｈｊ／ａ（Ｐｄ和Ｒｔｈｊ／ａ在第二页）， 在最大环境温度下结温不允许超过１２５ ° C 最大的电流根据晶闸管的体积来限定． 产品的热常数（ Ｃｔｈ ）是７分钟，意思是运行７分钟温升仅是稳定温度的６３％． Thermal specifications: Current according ambient temperature : The curve "1" gives the limits of the product. The temperature reached are acceptable for the components. These values are in compliance with most of SSRs manufacturers. In a cabinet with a minimum of ventilation or a non permanent current, these values are aceptable. 1 The curve "2" gives the limits of the product according to EN60947-4-3 with a maximum rise temperature of 50°C (@ 40°C) for a permanent current and in air calm ( test during 8 hours). 2 For a non permanent current, you can calcule the average power = Pd x duty cycle and check the rise temperature : ∆Tj = Pd x Rthj/a (Pd and Rthj/a are given page 2). The junction temperature must not exceed 125°C at the maximum ambient temperature. The maximum current is limited to the size of the thyristors. The thermal constant (Cth) of the product is 7 minutes. That means the rise temperature is only 63% of the stabilized temperature after a running time of 7 minutes. celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 celpac S/MON/SAL965460/C/10/02/2009 page 4 / 6F/GB 1 - 在不能再通电时获得的非重复Ｉｔｓｍ，这个曲线被用 图 ３： 过载电流／ Overload currents 于确认保护（熔丝）． 1 - No repetitive Itsm is given without voltage reapplied . This curve is used to define the protection (fuses). Fig.3 Surcharge de courant : Itsm (Apeak) = f(t) pour modéle 50A(Itsm=550A) Surge current : Itsm (Apeak) = f(t) for 50A models with Itsm =550A 600 这个曲线不能被超越． 注意：重复的浪涌电流会减小固态继电器的预期寿命． 2 - Repetitive Itsm is given for inrush current with initial Tj = 70°C. In normal operation , this curve musn't be exceeded. Be careful, repeated surge currents decrease life expectancy of the SSR. Itsm (Apeak) 2 - 重复Ｉｔｓｍ是初始温度 Tj =70 °C 时的涌入电流， 400 Surcharge de courant non répétitive sans tension réappliquée / No repetive surge current without voltage reapplied. 1 2 200 Surcharge de courant répétitive avec tension réappliquée / Repetive surge current with voltage reapplied. 0 0,01 0,1 1 t (s) 10 警告：在负载和主回路之间，半导体继电器不提供任何的电隔离，当继电器必须和主回路隔离或发生故障时确保可靠的绝缘，通常使用一个 −> 带隔离的断路器或一个类似的装置． Warning ! semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction −> with an adapted circuit breaker with isolation feature or a similar device in order to ensure a reliable insulation in the event of wrong function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration ...). 在ＤＩＮ导轨上安装和拆卸无需工具／ 面板安装／ Drill for vertical can be adjusted Mounting M5 M4 Panel Mounting Mounting and dismounting on DIN rail without any tool. 保护导线（接地）和ＤＩＮ导轨连接／ DIN rail connected to protection wire (ground) . Dismounting 88±2mm 12,7mm 警告：用户应该保护热敏感材料并且防止人与散热器接触， 为一好冷却， ＳＳＲ需要空气对流， 较少对流空气会导致异常发热，实际上在两个ＳＳＲ之间没有空间（在两个ＳＳＲ之间零空间） 请减少负载电流． 一个强制冷却（箱体内安装风扇）可以较大的改善散热的效果． 在任何情况下请检查散热器温度不能超出９０ ° C. 垂直位置／ Warning : The user should protect heat sensitive materials as well as persons against any contacts with the heatsink. For a good cooling, the SSR needs an air convection. Less convection air produces an abnormal heating. In case of no space between two SSR ( zero space between two SSRs) , please reduce the load current. A forced cooling ( fan inside the cabinet) improves significantly the thermal performances. In all cases please check the heatsink temperature never exceed 90°C. vertical position 80mm celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 celpac S/MON/SAL965460/C/10/02/2009 page 5 / 6F/GB 连接／ Connections celpac Power wiring 功率接线／ 导线的数量和大小 1 Fil rigide (sans embout) SOLID (No ferrule) 螺丝刀类型／ / Number of wires 推荐的扭矩／ Screwdriver type Recommended Torque 2 Fil multibrins (avec embout) FINE STRANDED (With ferrule) Fil rigide (sans embout) SOLID (No ferrule) Fil multibrins (avec embout) FINE STRANDED (With ferrule) M5 N.m 2 2 1,5 ... 10 mm 2 1,5 ... 6 mm 2 1,5 ... 10 mm 1,5 ... 6 mm AWG16....AWG8 AWG16....AWG10 AWG16....AWG8 AWG16....AWG10 POZIDRIV 2 2 环形压线端子／ 带或不带压线端子的导线直接连接／ Direct connection with wires with or without ferrules With ring terminals Washer for vibrations celpac Control wiring 控制接线／ 导线的数量和大小 1 Fil rigide (sans embout) SOLID (No ferrule) 推荐的扭矩／ 螺丝刀类型／ / Number of wires Screwdriver type Recommended Torque 2 Fil multibrins (avec embout) FINE STRANDED (With ferrule) Fil rigide (sans embout) SOLID (No ferrule) Fil multibrins (avec embout) FINE STRANDED (With ferrule) M3,5 N.m 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 POZIDRIV 2 or 0,8 x5,5mm 1,2 标签／ Marking label (1MZ09000) FASTONS : 咨询我们 / Consult us celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 celpac S/MON/SAL965460/C/10/02/2009 page 6 / 6F/GB 典型负载／ Typical LOADS −> ＳＡＬ９ 系列产品背专门设计用于ＡＣ－５１电阻性负载（加热）。 SAL9 products are specially designed for AC-51 résistive load (heating). 保护／ Protection : −> 固态继电器对于负载短路的保护取决于希望的协调． 允许有两种类型的协调，类型１和类型２． ａ） 类型１协调要求，在短路时，设备不会对人和装置产生危害，同时不需要更多的维护，无需维修和更换元件． 在此情况下，使用一个合适的保护是为了在短路后对带有ＳＳＲ的设备的维修． ｂ） 类型２协调要求，在短路情况下，设备不会导致危险给人或到装置，并且适和更长远的使用． 在类型２协调的情况下，为保护固态继电器以抵抗负载的短路，使用熔丝的 Ｉ ２ ｔ的值 ＝ １／２＊（第二页规定的 Ｉ２ ｔ的值）． 所做的试验是用 ＦＥＲＲＡＺ 熔丝． 用ＭＣＢ保护固态继电器也是可行的（ 微型断路器）． ２ ２ 在此情况下，看应用指南 （固态继电器保护） 和使用一个有高的 Ｉ ｔ 值的固态继电器 （最小５０００Ａ ｓ）． −> SSRs protection against short circuit of the load depends on the coordination wished. Two types of coordination are permissible, type 1 or type 2. a) Type 1 coordination requires that, under short-circuit conditions, the device shall cause no danger to persons or to the installation and may not be suitable for further service without repair and replacement of parts. In this case, use a protection adapted to the installation with the risk of SSR maintenance after a short circuit. b) Type 2 coordination requires that, under short-circuit conditions, the device shall cause no danger to persons or to the installation and shall be suitable for further use. In case of Type 2 coordination, to protect the SSR against a short-circuit of the load , use a fuse with an I2t value = 1/2 I2t value specified page 2. A test has been made with FERRAZ fuses . It is possible to protect SSR by MCB ( miniature circuit breaker). In this case, see application note ( SSR protection) and use a SSR with high I2t value (5000A2s minimum). EMC : −> 干扰： 在数据页中固态继电器的抗干扰等级符合这些产品的主要标准：ＥＮ６１０００－４－４＆５． Immunity : We give in our data-sheets the immunity level of our SSRs according to the main standards for these products: EN61000-4-4 &5. −> 辐射 ： ｃｅｌｄｕｃ固态继电器的设计主要符合元器件的标准 ｃｌａｓｓｅ Ａ （工业）． 在家庭环境中使用这些产品可能会引起无线电干扰，在这种情况下用户必需使用另外的设备． 固态继电器是一个综合设备它必须和别的元器件相互连接（负载，电缆，等）构成的系统．因为别的元器件或相互的连接不在 celduc的控制下，确定包含固态继电器的系统遵从可适用的系统水平的任何规则和规章的需求将是系统整合之人的职责． 考虑 celduc 的建议，在我们的实验室试验被预先完成． Emission: celduc SSRs are mainly designed in compliance with standards for class A equipment (Industry). Use of this product in domestic environments may cause radio interference. In this case the user may be required to employ additionnal devices to reduce noise. SSRs are complex devices that must be interconnected with other equipment (loads, cables, etc.) to form a system. Because the other equipment or the interconnections may not be under the control of celduc, it shall be the responsability of the system integrator to ensure that systems containing SSRs comply with the requirement of any rules and regulations applicable at the system level. Consult celduc for advices. Tests can be preformed in our laboratory. 说明书的修改不另行通知．／ Specifcations are subject to change without notice celduc r e l a i www.celduc.com s Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19