okpac - Celduc Relais

okpac
S/MON/SO942460/A/09/06/2004
页　１　／　５Ｆ／ＧＢ
功率固态继电器
Power Solid State Relay
SO942460
输出／Output : 12-280VAC 25A
输入／Input : 3-32VDC
❏ 过零触发，专门设计用于电阻负载．
Zero Cross Solid State Relay specially designed for resistive loads.
❏ 输出１２－２８０ＶＡＣ　２５Ａ．
Output 12 to 280VAC 25A.
❏ 大的控制电压范围：　３　－　３２ＶＤＣ　，有输入电流限制器．
在输入側有可见的绿色ＬＥＤ指示．
输入側有过电压保护．
Large control range: 3-32VDC with input current limiter.
Green LED visualization on the input.
Input over-voltage protection.
❏ 如需要有ＩＰ２０保护盖（可选）．
IP20 protection flaps on request (option).
❏ 设计符合标准：　ＥＮ６０９４７－４－３　（ＩＥＣ９４７－４－３）和ＥＮ６０９５０／ＶＤＥ０８０５，
（加强绝缘）　－ＵＬ－ｃＵＬ．
Designed in conformity with EN60947-4-3 (IEC947-4-3)
and EN60950/VDE0805 (Reinforced Insulation) -UL-cUL
没有ＩＰ２０盖子/ without IP20 flaps
有ＩＰ２０盖子/ with IP20 flaps
尺寸／Dimensions :
12-280VAC
线路保护／
line protection
1/L1
4/A2-
控制／
control
3-32VDC
ZC
2/T1
+
LED
3/A1+
*－　１／Ｌ１　和　２／Ｔ１　端子接线可以交换．
1/L1 et 2/T2 peuvent être inversées/
1/L1
changed
1/L1and
and2/T2
2/T1can
canbebe
swapped.
*－　固态继电器必须安装在散热器上．
le relais doit être monté sur dissipateur thermique /
be mountedononheatsink
a heatsink
SSR SSR
mustmust
be mounted
典型应用：
电阻　５　ｋＷ
（　ＡＣ－５１　负载）　电压为　２３０　ＶＡＣ
负载/LOAD
Typical
application:
5 kW resistor
(AC-51 load)
on 230 VAC
如需要有ＩＰ２０盖子/ with IP20 flaps on request
Proud to serve you
All technical caracteristics are subject to change without previous notice.
Caractéristiques sujettes à modifications sans préavis.

celduc
r
e
l
a
i
s
okpac
S/MON/SO942460/A/29/06/2004
页　２　／　５Ｆ／ＧＢ
控制特性 / Control characteristics (at 25°C)
输入／Input : Ic = f( Uc)
DC
Typ
Max
5-12-24 32
<13
<13
14
Ic (mA)
参数　／　Parameter
Symbol Min
Unit
12
控制电压　／　Control voltage
Uc
3
V
10
控制电流　／　Control current (@ Uc
)
Ic
<10
mA
8
释放电压　／　Release voltage
Uc off
2
V
6
输入ＬＥＤ　／　Input LE D
ｖｅｒｔｅ
绿色
／green
4
反向电压　／　Reverse voltage
Urv
32
V
2
钳位电压　／　Clamping
(Trail)
voltage
Uclamp
36
V
0
0 2 4 6 8 10 12 14 16 18 20 22 24 26
抗干扰　／　Input immunity : EN61000-4-4
2kV
Uc (VDc)
抗干扰　／　Input immunity : EN61000-4-5
2KV
输出特性 / Output characteristics (at 25°C)
参数　／　Parameter
Conditions
Symbol
工作电压　／　Operating voltage
range
Ue
峰值电压　／　Peak voltage
Up
过零触发电压　／　Zero cross level
Usync
关闭电压　／　Latching voltage
Ie nom
Ua
额定电流　／　nominal current (AC-51)
Ie AC-51
非重复过载电流　／　Non repetitive overload current
tp=10ms (Fig. 3)
Itsm
通态电压降　／　On state voltage drop
@ 25°C
Vt
通态动态电阻　／　On state dynamic resistance
rt
输出功率消耗　（最大值）　／　Pd
Output power dissipation (max value)
结和外壳之间的热阻／
Rthj/c
Thermal resistance between junction to case
断态漏电流 ／　Off state leakage current
@Ue typ, 50Hz
Ilk
最小负载电流　／　Minimum load current
Iemin
接通时间　／　Turn on time
@Ue typ, 50Hz
ton max
关断时间　／　Turn off　time
@Ue typ, 50Hz
toff max
工作频率／　Operating frequency range
F mains
f
断态　ｄｖ／ｄｔ　／　Off state
dv/dt
dv/dt
非重复最大　ｄｉ／ｄｔ　／　Maximum di/dt non repetitive
di/dt
I2t (<10ms)
I2t
抗干扰水平　／　Conducted immunity level
IEC/EN61000-4-4 (bursts)
抗干扰水平　／　Conducted immunity level
IEC/EN61000-4-5 (surge)
短路保护　／　Short circuit protection
见第５页/see page 5
Example
通用特性 / General characteristics (at 25°C)
输入－输出绝缘　／　Input to output insulation
输出－外壳绝缘　／　Output to case insulation
绝缘电阻　／　Insulation resistance
额定脉冲电压　／　Rated impulse voltage
保护等级　／　Protection level / CEI529
污染程度　／　Pollution degree
震动　／　Vibration withstand 10 -55 Hz according to CEI68
冲击　／　Shocks withstand according to CEI68
环境温度　／　Ambient temperature (no icing, no condensation)
储藏温度／　Storage temperature (no icing, no condensation)
环境湿度　／　Ambient humidity
重量／　Weight
符合 ／　Conformity
符合 ／　Conformity
外壳材料　／　Housing Material
底板　／　Base plate
Min
12
600
Max
280
35
8
25
250
350
0,85
16
0,9x0,85xIe + 0,015xIe2
0,1
500
50-60
312
600
2kV criterion B
Unit
V rms
V
V
V
A rms
A
V
mΩ
W
1,7
K/W
1
mA
mA
ms
ms
Hz
V/µs
A/µs
A2s
5
10
10
800
50
2kV criterion A with external VDR
Fuse FERRAZ gRC 25A/32A 14x51
Symbol
Ui
Ui
Ri
Uimp
double amplitude
HR
Typ.
230
28 30 32
4000
VRMS
4000
VRMS
1000 (@500VDC) MΩ
4000
V
IP00
2
1,5
mm
30/50
g
-55/+80
°C
-55/+125
°C
40 to 85
%
80
g
EN60947-4-3 (IEC947-4-3)
EN60950 UL/cUL
PA 6/6 UL94VO
Aluminium, nickel-plated

celduc
r
e
l
a
i
www.celduc.com
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : [email protected]
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
okpac
S/MON/SO942460/A/09/07/2004
页　３　／　５Ｆ／ＧＢ
图２／Ｆｉｇ．　２　热量曲线和散热器选择　／　Thermal curves and heatsink choice
2,1K/W 1,5K/W
30
1,1K/W
30
功率消耗 / Power Dissipation (W)
25
25
Full on State
4K/W
20
20
6K/W
15
15
10
10
12K/W
50% on State
5
5
0
0
5
10
15
20
0
0 10 20 30 40 50 60 70 80 90 100
25
负载电流 / RMS load current (A)
环境温度 / Ambient temperature (°C)
１２Ｋ／Ｗ　对应于继电器无散热器　／　12K/W corresponds to a relay without heatsink .
６Ｋ／Ｗ　对应于继电器安装在　ＤＩＮ　导轨适配器上．　如ｃｅｌｄｕｃ的产品　１ＬＤ１２０２０．
6K/W corresponds to a relay mounted on a DIN rail adaptator like celduc 1LD12020
图３／Ｆｉｇ　３　：　过载电流　／　Overload currents
2 -初始温度Ｔｊ　＝　７０°Ｃ　时的浪涌电流所产生的
重复的Ｉｔｓｍ，通常情况下，不允许超过此曲线．
注意：　重复的浪涌电流会减少固态继电器的预期
寿命．
2 - Repetitive Itsm is given for inrush current with
initial Tj = 70°C. In normal operation , this curve
musn't be exceeded.
Be careful, the repetition of the surge current
decreases the life expectancy of the SSR.
图３／Ｆｉｇ．３ 浪涌电流　：　Ｉｔｓｍ（Ａｐｅａｋ）　＝　ｆ（ｔ）　模块为　２５Ａ　（Ｉｔｓｍ＝２３０Ａ）　Surge current : Itsm (Apeak) = f(t) for 25A models with Itsm =230A
250
Itsm (Apeak)
1 - 不能再通电的非重复Ｉｔｓｍ　的获得，这一
曲线被用于确认固态继电器的保护．
1 - No repetitive Itsm is given without voltage
reapplied . This curve is used to define the
protection (fuses).
200
150
不能再通电的非重复浪涌电流　／　No repetive surge current without voltage reapplied.
100
50
1
2
能再通电的重复浪涌电流／
Repetive surge current with voltage reapplied.
0
0,01
0,1
1
10
t(s)
−>
警告　！　在负载和主回路之间半导体继电器不提供任何电隔离，总是使用有隔离性能的适合的断路器或相似的设备连接，是为
了错误功能发生和当继电器必须从主回路被隔离时保证可靠的绝缘（维护：如果在一个较长的时间里没有被使用．．．）．
−>
Warning ! semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction
with an adapted circuit breaker with isolation feature or a similar device in order to ensure a reliable insulation in the event of wrong
function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration ...).

celduc
r
e
l
a
i
www.celduc.com
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : [email protected]
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
okpac
S/MON/SO942460/B/01/03/2005
页　４　／　５Ｆ／ＧＢ
连接／ Connections
直接接线有或没有套圈／
Direct connection with wires with or without ferrules
okpac
有压接端子（环形端子）／
With ring terminals
控制接线／ Control wiring
螺丝起子类型／
Screwdriver type
导线号/ Number of wires
1
推荐的扭矩／
Recommended Torque
2
单根硬线
（没有套圈）
SOLID
(No ferrule)
多根软线
（有套圈）　FINE STRANDED
(With ferrule)
单根硬线
（没有套圈）
SOLID
(No ferrule)
多根软线
（有套圈）　FINE STRANDED
(With ferrule)
0,75 ... 2,5 mm2
0,75 ... 2,5 mm2
0,75 ... 2,5 mm2
0,75 ... 2,5 mm2
M4
N.m
POZIDRIV 2
1,2
螺丝起子类型／
Screwdriver type
推荐的扭矩／
Recommended Torque
AWG18....AWG14 AWG18....AWG14 AWG18....AWG14 AWG18....AWG14
okpac
主回路接线／ Power wiring
导线号 / Number of wires
1
单根硬线
（没有套圈）
SOLID
(No ferrule)
2
多根软线
（有套圈）　FINE STRANDED
(With ferrule)
单根硬线
（没有套圈）
SOLID
(No ferrule)
多根软线
（有套圈）　FINE STRANDED
(With ferrule)
M5
N.m
1,5 ... 10 mm
2
1,5 ... 6 mm
2
1,5 ... 10 mm
2
1,5 ... 6 mm
2
AWG16....AWG8 AWG16....AWG10 AWG16....AWG8 AWG16....AWG10
主回路用的环形端子 / Power with ring
terminals.
W max =12,6mm
16 mm2 (AWG6)
25 mm2 (AWG4)
35mm2 (AWG2 /AWG3)
50mm2 (AWG0 /AWG1)
用于大电流的适配的环形端子和专用配件也能制造：
详见大电流固太继电器和数据页中的主回路连接部
分．／　Suitable ring terminals and special kit for high
current can be delivered: see high power SSR and datasheet for power connexion.
POZIDRIV 2
2
可选　：　ＩＰ２０盖子　1K453000 = 盖子不装备．
1LK00500 = 一个盖子（在输出端）由 celduc装备．
1LK00600 = 二个盖子（在输入和输出端）由 celduc装备．
Option : IP20 flaps
1K453000 : Flap reference without mounting
1LK00500 = 1 flap (on output) + 1 celduc mounting
1LK00600 = 2 flaps (input & output) + 2 celduc mounting
快速连接端子／FASTONS : 和我们联系 / Consult us

celduc
r
e
l
a
i
www.celduc.com
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : [email protected]
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
okpac
S/MON/SO942460/A/09/07/2004
页　５　／　５Ｆ／ＧＢ
安装 /Mounting:
okpac 系列固态继电器必须被安装在散热器上．
可用到的散热器是一个大的系列．
www.celduc.com.
见下面的例子，且在　上可找到＂ＷＦ＂系列散热器．
okpac SSRs must be mounted on heatsinks. A large range of heatsinks is available.
−>
−>
See below some examples and "WF" range on www.celduc.com.
对散热器的安装，必须使用 celduc 指定的导热脂和导热垫使其具有高的热传导
能力．　For heatsink mounting, it is necessary to use thermal grease or thermal pad with high
conductibility specified by celduc.
M4x12mm
1,2N.m
导热脂和导热垫／Thermal grease or pad
推进去然后
盖上．／
Push and
close
导热垫／Thermal pad :
5TH21000
WF151200
(2-2,5 K/W)
ＩＰ２０盖子安装
1LD12020
ＤＩＮ　导轨适配器／
/ IP20 flaps mounting
DIN rail adaptator
典型应用 / Typical LOADS
−> ＳＯ９产品是专门设计用于　ＡＣ－５１　电阻负载（加热）．
对其它的负载，见我们的选型指南．　SO9 product is specially designed for AC-51 résistive load (heating). For other loads, consult our selection guide
保护 / Protection :
−> 为保护固态继电器以抵抗负载的短路，使用熔丝的　Ｉ２ｔ的值　＝　１／２＊（第二页规定的　Ｉ２ｔ的值）．　所做的试验是用　ＦＥＲＲＡＺ　熔丝．　用ＭＣＢ保护固态继电器也是可行的（　微型断路器）．　在此情况下，看应用指南　（固态继电器保护）　和使用一个有高的　Ｉ２ｔ　值的固态继电器　（最小５０００Ａ２ｓ）．
To protect the SSR against a short-circuit of the load , use a fuse with a I2t value = 1/2 I2t value specified page 2.
A test has been made with FERRAZ fuses .
It is possible to protect SSR by MCB ( miniature circuit breaker).
In this case, see application note ( SSR protection) and use a SSR with high I2t value (5000A2s minimum).
EMC :
−>
抗干扰性　：　对这些固态继电器，根据主要的标准：ＥＮ６１０００－４－４　＆５，在数据也上给出了抗干扰性的等级．
Immunity :
We give in our data-sheets the immunity level of our SSRs according to the main standards for these of products: EN61000-4-4 &5.
−> 辐射　：　ｃｅｌｄｕｃ固态继电器的设计主要符合元器件的标准　ｃｌａｓｓｅ　Ａ　（工业）．　在家庭环境中使用这些产品可能会引起无线电干扰，在这种情况下用户必需使用另外的设备．
固态继电器是一个综合设备它必须和别的元器件相互连接（负载，电缆，等）构成的系统．因为别的元器件或相互的连接不在
celduc 的控制下，确定包含固态继电器的系统遵从可适用的系统水平的任何规则和规章的需求将是系统整合之人的职责．
考虑 celduc 的建议，在我们的实验室试验被预先完成．
Emission: celduc SSRs are mainly designed in compliance with standards for class A equipment (Industry).
Use of this product in domestic environments may cause radio interference. In this case the user may be required to employ
additionnal devices to reduce noise. SSRs are complex devices that must be interconnected with other equipment (loads, cables, etc.)
to form a system. Because the other equipment or the interconnections may not be under the control of celduc, it shall be the
responsability of the system integrator to ensure that systems containing SSRs comply with the requirement of any rules and
regulations applicable at the system level.
Consult celduc for advices. Tests can be preformed in our laboratory.

celduc
r
e
l
a
i
www.celduc.com
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : [email protected]
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19