uPC2747TB,uPC2748TB DS

BIPOLAR ANALOG INTEGRATED CIRCUITS
PC2747TB,PC2748TB
D
3 V, SUPER MINIMOLD SILICON MMIC
AMPLIFIER FOR MOBILE COMMUNICATIONS
UE
DESCRIPTION
The PC2747TB, PC2748TB are silicon monolithic integrated circuits designed as amplifier for mobile
communications. These ICs are packaged in super minimold package which is smaller than conventional minimold.
These ICs are manufactured using our 20 GHz fT NESAT lll silicon bipolar process. This process uses silicon
nitride passivation film and gold electrodes. These materials can protect chip surface from external pollution and
prevent corrosion/migration. Thus, these ICs have excellent performance, uniformity and reliability.
FEATURES
• Supply voltage
: VCC = 2.7 to 3.3 V
O
NT
IN
• Noise figure
: PC2747TB ; NF = 3.3 dB TYP. @ f = 900 MHz
PC2748TB ; NF = 2.8 dB TYP. @ f = 900 MHz
• Power gain
: PC2747TB ; GP = 12 dB TYP. @ f = 900 MHz
PC2748TB ; GP = 19 dB TYP. @ f = 900 MHz
• Operating frequency
: PC2747TB ; DC to 1.8 GHz
• Isolation
: PC2747TB ; ISL = 40 dB TYP. @ f = 900 MHz
PC2748TB ; 0.2 to 1.5 GHz
PC2748TB ; ISL = 40 dB TYP. @ f = 900 MHz
• High-density surface mounting : 6-pin super minimold package (2.0  1.25  0.9 mm)
APPLICATION
• Buffer amplifiers for mobile telephones, etc. (PDC800M, GSM)
ORDERING INFORMATION
Package
Marking
SC
Part Number
PC2747TB-E3
6-pin super minimold
PC2748TB-E3
C1S
Supplying Form
 Embossed tape 8 mm wide
 1, 2, 3 pins face the perforation side of the tape
C1T
 Qty 3 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
DI
Part number for sample order: PC2747TB-A, PC2748TB-A
Caution: Observe precautions when handling because these devices are sensitive to electrostatic discharge
Document No. PU10201EJ01V0DS (1st edition)
(Previous No. P13444EJ3V0DS00)
Date Published December 2002 CP(K)
The mark  shows major revised points.
PC2747TB,PC2748TB
PIN CONNECTIONS
Pin Name
1
INPUT
2
GND
3
GND
4
OUTPUT
5
GND
6
VCC
D
Pin No.
UE
Marking is an example of  PC2747TB
PRODUCT LINE-UP (T A = +25C, VCC = 3.0 V, ZS = ZL =50 )
Part No.
PC2745T
fu
(GHz)
PO (sat)
(dBm)
GP
(dB)
NF
(dB)
2.7
1.0
12
6.0
PC2745TB
PC2746TB
PC2747T
PC2747TB
PC2748T
PC2748TB
PC2749T
PC2749TB
7.5
Package
6-pin minimold
1.5
0
19
4.0
7.5
6-pin minimold
C1Q
C1R
6-pin super minimold
1.8
7.0
12
3.3
5.0
6-pin minimold
C1S
6-pin super minimold
1.5
3.5
19
2.8
6.0
6-pin minimold
C1T
6-pin super minimold
2.9
6.0
16
4.0
6.0
6-pin minimold
6-pin super minimold
Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail.
Caution The package size distinguishes between minimold and super minimold.
SYSTEM APPLICATION EXAMPLE
DI
SC
EXAMPLE OF DIGITAL CELLULER TELEPHONE
2
Marking
6-pin super minimold
O
NT
IN
PC2746T
ICC
(mA)
Data Sheet PU10201EJ01V0DS
C1U
PC2747TB,PC2748TB
PIN EXPLANATION
Pin Name
Applied
Pin
Voltage
Voltage
(V)
1
INPUT

(V)
Function and Applications
Note
0.80
Signal input pin.
A internal matching circuit, configured with
resistors, enables 50  connection over a
0.80
wide band.
This pin must be coupled to signal source
GND
0

Ground pin.
UE
with capacitor for DC cut.
2
Internal Equivalent Circuit
D
Pin
No.
3
This pin should be connected to system
5
ground with minimum inductance. Ground
pattern on the board should be formed as
wide as possible. All the ground pins must
be connected together with wide ground
pattern to decrease impedance difference.
OUTPUT

2.79
Signal output pin.
O
NT
IN
4
A internal matching circuit, configured with
resistors, enables 50  connection over a
2.72
6
VCC
2.7 to 3.3

wide band.
The above diagram is for the
This pin must be coupled to next stage with
PC2747TB.
capacitor for DC cut.
The resistor marked with an asterisk
Power supply pin.
does not exist in the  PC2748TB.
This pin should be externally equipped with
bypass capacity to minimize ground
impedance.
DI
SC
Note Pin voltage is measured at VCC = 3.0 V. Above: PC2747TB, Below: PC2748TB
Data Sheet PU10201EJ01V0DS
3
PC2747TB,PC2748TB
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Conditions
Ratings
Unit
Supply Voltage
VCC
TA = +25C
4.0
V
Circuit Current
ICC
TA = +25C
15
mA
Power Dissipation
PD
TA = +85C
270
mW
Operating Ambient Temperature
TA
40 to +85
C
Storage Temperature
Tstg
55 to +150
C
Input Power
Pin
0
dBm
D
Note
UE
TA = +25C
Note Mounted on double-sided copper-clad 50  50  1.6 mm epoxy glass PWB
RECOMMENDED OPERATING RENGE
Parameter
MIN.
VCC
2.7
TYP.
MAX.
Unit
3.0
3.3
V
O
NT
IN
Supply Voltage
Symbol
ELECTRICAL CHARACTERISTICS
(T A = +25C, VCC = 3.0 V, ZS = ZL = 50 , unless otherwise specified)
Parameter
Symbol
PC2747TB
Test Conditions
PC2748TB
Unit
MIN. TYP. MAX. MIN. TYP. MAX.
Circuit Current
Power Gain
Noise Figure
Upper Limit Operating Frequency
ICC
No Signal
GP
NF
fu
3.8
5.0
7.0
4.5
6.0
8.0
mA
f = 900 MHz
9
12
14
16
19
21
dB
f = 900 MHz
–
3.3
4.5
–
2.8
4.0
dB
1.5
1.8
–
1.2
1.5
–
GHz
–
–
–
–
0.2
0.4
GHz
3 dB down below from gain at
f = 0.9 GHz
Lower Limit Operating Frequency
fL
3 dB down below from gain at
f = 0.9 GHz
Isolation
f = 900 MHz
35
40
–
35
40
–
dB
RLin
f = 900 MHz
11
14
–
8.5
11.5
–
dB
7
10
–
5.5
8.5
–
dB
–9.5
–7.0
–
–6.0
–3.5
–
dBm
SC
Input Return Loss
ISL
RLout
f = 900 MHz
Saturated Output Power
PO (sat)
f = 900 MHz, Pin = –8 dBm
DI
Output Return Loss
4
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
STANDARD CHARACTERISTICS FOR REFERENCE (T A = +25C, ZS = ZL =50 )
Parameter
Symbol
Test Conditions
Reference
Unit
PC2747TB PC2748TB
ICC
VCC = 1.8 V, No signal
3.0
3.5
mA
Power Gain
GP
VCC = 1.8 V, f = 900 MHz
5.5
11.5
dB
Noise Figure
NF
VCC = 1.8 V, f = 900 MHz
5.2
4.5
dB
VCC = 1.8 V,
1.8
1.5
GHz
Upper Limit Operating Frequency
fu
Lower Limit Operating Frequency
fL
VCC = 1.8 V,
UE
3 dB down below from gain at f = 0.9 GHz
D
Circuit Current

0.2
GHz
34
34
dB
11
10
dB
13
12
dB
13.7
10.0
dBm
34
38
dBc
20
28
3 dB down below from gain at f = 0.9 GHz
Isolation
ISL
VCC = 1.8 V, f = 900 MHz
Input Return Loss
RLin
VCC = 1.8 V, f = 900 MHz
Output Return Loss
RLout
VCC = 1.8 V, f = 900 MHz
Saturated Output Power
PO (sat)
VCC = 1.8 V, f = 900 MHz, Pin = 8 dBm
Distortion
IM3
VCC = 3.0 V, Pout = 20 dBm,
O
NT
IN
3rd Order Intermodulation
f1 = 900 MHz, f2 = 902 MHz
VCC = 1.8 V, Pout = 20 dBm,
DI
SC
f1 = 900 MHz, f2 = 902 MHz
Data Sheet PU10201EJ01V0DS
5
PC2747TB,PC2748TB
O
NT
IN
EXAMPLE OF APPLICATION CIRCUIT
UE
D
TEST CIRCUIT
SC
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
CAPACITORS FOR VCC, INPUT AND OUTPUT PINS
1 000 pF capacitors are recommendable as bypass capacitor for VCC pin and coupling capacitors for input/output
pins.
Bypass capacitor for VCC pin is intended to minimize VCC pin’s ground impedance. Therefore, stable bias can be
supplied against VCC fluctuation.
Coupling capacitors for input/output pins are intended to minimize RF serial impedance and cut DC.
DI
To get flat gain from 100 MHz up, 1 000 pF capacitors are assembled on the test circuit. [Actually, 1 000 pF
capacitors give flat gain at least 10 MHz. In the case of under 10 MHz operation, increase the value of coupling
capacitor such as 2 200 pF. Because the coupling capacitors are determined by the equation of f C = 1/(2 RC).]
6
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
O
NT
IN
UE
D
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
COMPONENT LIST
Value
C
1 000 pF
For more information on the use of this IC, refer to the following application note: USAGE AND APPLICATIONS
OF 6-PIN MINI-MOLD, 6-PIN SUPER MINI-MOLD SILICON HIGH-FREQUENCY WIDEBAND AMPLIFIER MMIC
DI
SC
(P11976E).
Data Sheet PU10201EJ01V0DS
7
PC2747TB,PC2748TB
TYPICAL CHARACTERISTICS (T A = +25C, unless otherwise specified)
DI
SC
O
NT
IN
UE
D
 PC2747TB 
8
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
DI
SC
O
NT
IN
UE
D
 PC2747TB 
Remark The graphs indicate nominal characteristics.
Data Sheet PU10201EJ01V0DS
9
PC2747TB,PC2748TB
SMITH CHART (T A = +25C, VCC = 3.0 V)
 PC2747TB 
DI
SC
S22-FREQUENCY
O
NT
IN
UE
D
S11-FREQUENCY
10
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
S-PARAMETERS
DI
SC
O
NT
IN
UE
D
 PC2747TB 
Data Sheet PU10201EJ01V0DS
11
PC2747TB,PC2748TB
TYPICAL CHARACTERISTICS (T A = +25C, unless otherwise specified)
DI
SC
O
NT
IN
UE
D
 PC2748TB 
12
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
DI
SC
O
NT
IN
UE
D
 PC2748TB 
Remark The graphs indicate nominal characteristics.
Data Sheet PU10201EJ01V0DS
13
PC2747TB,PC2748TB
SMITH CHART (T A = +25C, VCC = 3.0 V)
 PC2748TB 
DI
SC
S22-FREQUENCY
O
NT
IN
UE
D
S11-FREQUENCY
14
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
S-PARAMETERS
DI
SC
O
NT
IN
UE
D
 PC2748TB 
Data Sheet PU10201EJ01V0DS
15
PC2747TB,PC2748TB
PACKAGE DIMENSIONS
DI
SC
O
NT
IN
UE
D
6-PIN SUPER MINIMOLD (UNIT: mm)
16
Data Sheet PU10201EJ01V0DS
PC2747TB,PC2748TB
NOTES ON CORRECT USE
(1) Observe precautions for handling because of electro-static sensitive devices.
(2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired
oscillation).
All the ground pins must be connected together with wide ground pattern to decrease impedance difference.
D
(3) The bypass capacitor should be attached to VCC line.
(4) The DC cut capacitor must be attached to input and output pin.
RECOMMENDED SOLDERING CONDITIONS
For soldering
UE
This product should be soldered and mounted under the following recommended conditions.
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Infrared Reflow
Soldering Conditions
Peak temperature (package surface temperature)
: 260C or below
Time at peak temperature
: 10 seconds or less
Time at temperature of 220C or higher
Preheating time at 120 to 180C
Wave Soldering
Partial Heating
IR260
: 60 seconds or less
: 12030 seconds
: 3 times
O
NT
IN
Maximum number of reflow processes
VPS
Condition Symbol
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (package surface temperature)
: 215C or below
Time at temperature of 200C or higher
: 25 to 40 seconds
Preheating time at 120 to 150C
: 30 to 60 seconds
Maximum number of reflow processes
: 3 times
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (molten solder temperature)
: 260C or below
Time at peak temperature
: 10 seconds or less
Preheating temperature (package surface temperature)
: 120C or below
Maximum number of flow processes
: 1 time
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (pin temperature)
: 350C or below
Soldering time (per side of device)
: 3 seconds or less
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
VP215
WS260
HS350
DI
SC
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PU10201EJ01V0DS
17
NOTICE
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and
application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California
Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits,
software, or information.
2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does
not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property
rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express,
implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas
Electronics or others.
4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern
Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy
or otherwise misappropriation of Renesas Electronics product.
5. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The recommended applications
for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; office equipment; communications
equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and
industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime
systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct
threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear
reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas
Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product
for which the product is not intended by California Eastern Laboratories or Renesas Electronics.
6. You should use the Renesas Electronics products described in this document within the range specified by California Eastern Laboratories, especially with
respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product
characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products
beyond such specified ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as
the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation
resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by
fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy,
fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of
microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you.
8. Please contact a California Eastern Laboratories sales office for details as to environmental matters such as the environmental compatibility of each Renesas
Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for
damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document
for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When
exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics
product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and
Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories.
12. Please contact a California Eastern Laboratories sales office if you have any questions regarding the information contained in this document or Renesas
Electronics products, or if you have any other inquiries.
SC
O
NT
IN
UE
D
1.
NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
NOTE 3: Products and product information are subject to change without notice.
DI
CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus