BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Device Features Preliminary Datasheet +5V/680mA at operating bias condition Gain = 27.3 dB @ 1850 MHz P1dB = 33.1 dBm @ 1850MHz LTE 10M ACLR = 23.5dBm Output Power at -50dBc @ 1850MHz Intergrated interstage matching Lead-free/Green/RoHS-compliant QFN5x5 SMT package Product Description Typical Performance1 The BMT332 is a high dynamic range twostage power amplifier housed in RoHS compliant 20 pin, 5x5mm QFN package. The BMT332 uses a high reliability InGaP/ GaAs HBT process technology. The BMT332 is designed for use where high linearity and gain is required. The BMT332 is able to deliver over 23 dBm output power from 700 to 2400MHz while maintaining superior ACLR performance with a few external matching components. All devices are 100% RF/DC screened. Parameter Frequency 850 1750 1850 1960 Unit 2140 2350 MHz Gain 33.5 28.0 27.3 26.7 26.0 24.0 dB S11 -18.0 -30.0 -30.0 -26.0 -17.0 -17.0 dB -14.5 -11.5 -11.5 -12.0 -11.0 -12.5 dB OIP3 P1dB 50.0 33.6 50.0 33.2 49.0 33.1 49.0 33.1 47.5 33.2 47.5 33.1 dBm dBm LTE 10M ACLR 23.4 23.4 23.5 23.2 23.8 23.2 dBm WCDMA ACLR 23.5 7.0 23.7 5.6 23.7 5.6 23.5 5.5 24.0 5.5 23.5 5.3 dBm dB S22 2 Noise Figure 1 Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system. 2 OIP3 _ measured on two tones with a output power 23dBm/ tone , F2-F1 = 1 MHz.. Applications Base station /Repeaters Infrastructure *ACLR Channel Power measured at -50dBc. Commercial/Industrial/Military wireless system - WCDMA set-up: 3GPP WCDMA, TM1+64DPCH, +5MHz offset, PAR 9.78 at 0.01% Prob. - LTE set-up: 3GPP LTE, FDD E-TM3.1, 10MHz BW, ±5MHz offset, PAR 9.75 @0.01% Prob. Min. LTE / WCDMA /CDMA Wireless Infrastructure Bandwidth Ibias @ (IREF1&2 + IB1&2) IC @ (IC1 + IC2) VCC/VBias RTH Application Circuits Typical 700 Max. Unit 2400 MHz mA mA V °C/W 33 680 5.0 7.9 Absolute Maximum Ratings Parameter Operating Case Temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power *external matching circuit: refer to the page 4 to 19. BeRex Rating -40 to +85 -55 to +155 +200 Unit °C °C °C +6 2000 23 V mA dBm *Operation of this device above any of these parameters may result in permanent damage. ●website: www.berex.com ● email: [email protected] 1 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Pin Configuration Pin No. Label 1 IREF1 4,5 RF IN 6 VCC1 11,12,13 RF OUT/VCC2 16 VB2 19 IREF2 20 VB1 2,3,7,8,9,10,14, GND 15,17,18 Backside Paddle V-I Characteristics GND BeRex Evaluation Board Figure about the reference position of components BMT332 BeRex ●website: www.berex.com ● email: [email protected] 2 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Typical Device Data Preliminary Datasheet S-parameters (Vcc & VBias = +5V, Icq=680mA, Ta=25°C) BeRex S-Parameter (Vcc & VBias = +5V, Icq = 680mA, Ta= 25 °C, calibrated to device leads) Freq [MHz] S11 [Mag] S11 [Ang] S21 [Mag] S21 [Ang] S12 [Mag] S12 [Ang] S22 [Mag] S22 [Ang] 100 500 1000 1500 2000 2500 3000 3500 0.913 0.619 0.701 0.784 0.826 0.877 0.856 0.863 173.761 171.121 -177.176 177.684 174.821 167.581 164.082 160.570 24.816 26.921 15.441 10.073 5.629 2.533 0.614 0.198 32.166 -92.025 -178.364 107.582 28.494 -60.751 -113.048 -148.521 0.003 0.001 0.002 0.001 0.001 0.002 0.003 0.002 79.828 -44.058 59.383 119.430 52.589 52.748 73.959 48.291 0.801 0.869 0.879 0.895 0.901 0.909 0.876 0.800 -178.428 -176.093 -177.489 179.724 177.048 174.926 171.808 161.758 4000 0.868 160.252 0.085 179.517 0.004 44.770 0.607 121.233 ●website: www.berex.com ● email: [email protected] 3 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 850 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A 68pF 1nF N/A 3.3pF 100pF 5pF N/A 10pF 100pF 1uF 100pF 1nF 10uF 5.6nH 22nH 22nH 100 Ω Tantalum R2 0603 270 Ω ±5% PCB Diagram High Q Tantalum Coil ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 20 Object L1 C8 C10 C3 C6 C4 Distance 8.0mm 5.3mm 9.0mm 7.2mm 2.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘10pF(251R14S100JV4, EIA 0603) of Johanson Technology. 3. You could change C7 from 100 pF to 0 Ω or a line if you have other DC block front of BMT332. BeRex ●website: www.berex.com ● email: [email protected] 4 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 5 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 6 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 1750 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 N/A 1nF 1nF N/A 1nF 2pF 0Ω 3.3pF 2.7pF 4.3pF 3.9pF 1uF 100pF 1nF 10uF N/A 12nH 22nH 100 Ω R2 0603 270 Ω PCB Diagram ±5% High Q Tantalum Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C2 Distance 5.5mm 4.4mm 2.8mm 7.2mm 2.0mm 1.0mm 10.6mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘4.3pF(251R14S4R3BV4, EIA 0603) of Johanson Technology. 3.C7 : Non-critical 0 Ω. BeRex ●website: www.berex.com ● email: [email protected] 7 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 8 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 9 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 1850 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 N/A 1nF 1nF N/A 1nF 3pF 0Ω 3.3pF 2.7pF 4.3pF 3.9pF 1uF 100pF 1nF 10uF N/A 12nH 12nH 100 Ω R2 0603 270 Ω PCB Diagram ±5% High Q Tantalum Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C2 Distance 5.0mm 3.5mm 2.5mm 5.5mm 2.0mm 1.0mm 10.6mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘4.3pF(251R14S4R3BV4, EIA 0603) of Johanson Technology. 3.C7 : Non-critical 0 Ω. BeRex ●website: www.berex.com ● email: [email protected] 10 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 11 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 12 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 1960 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 N/A 1nF 1nF N/A 1nF 2pF 0Ω 3.3pF 2.7pF 4.3pF 3.9pF 1uF 100pF 1nF 10uF N/A 12nH 12nH 100 Ω R2 0603 270 Ω PCB Diagram ±5% High Q Tantalum Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C2 Distance 5.0mm 3.1mm 2.0mm 5.0mm 2.0mm 1.0mm 10.6mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘4.3pF(251R14S4R3BV4, EIA 0603) of Johanson Technology. 3.C7 : Non-critical 0 Ω. BeRex ●website: www.berex.com ● email: [email protected] 13 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 14 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 15 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 2140 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A 1nF 1nF 1nF 3pF 0Ω 3pF 2.7pF 3.9pF 4.3pF 1uF 100pF 1nF 10uF N/A 12nH 10nH 100 Ω Tantalum R2 0603 270 Ω ±5% PCB Diagram ±5% High Q Tantalum Coil ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C4 Distance 4.1mm 2.2mm 1.8mm 3.0mm 2.0mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘3.9pF(251R14S3R9BV4, EIA 0603) of Johanson Technology. 3.C7 : Non-critical 0 Ω. BeRex ●website: www.berex.com ● email: [email protected] 16 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier BeRex 35 30 Po [dBm] 25 20 15 10 Pout 5 Gain PAE 0 -10 -8 -6 -4 -2 0 2 4 6 45 40 35 30 25 20 15 10 5 0 PAE[%] Preliminary Datasheet Typical Performance 8 10 Pin [dBm] ●website: www.berex.com ● email: [email protected] 17 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 18 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 2350 MHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A N/A 0.75pF 1nF 1nF 0Ω 2.2pF 2.7pF 3.3pF 22pF 1uF 100pF 1nF 10uF N/A 15nH 10nH 100 Ω Tantalum R2 0603 270 Ω ±5% PCB Diagram ±5% High Q Tantalum Coil ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C6 C5 C4 Distance 3.6mm 0.6mm 1.3mm 2.0mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used ‘3.3pF(251R14S3R3BV4, EIA 0603) of Johanson Technology. 3.C7 : Non-critical 0 Ω. BeRex ●website: www.berex.com ● email: [email protected] 19 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 20 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 21 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Package Outline Dimension BeRex ●website: www.berex.com ● email: [email protected] 22 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Suggested PCB Land Pattern and PAD Layout BeRex • Notes 1. Use 1 oz. copper minimum for top and bottom layer metal. 2. A heatsink underneath the area of the PCB for the mounted device is required for proper thermal operation. 3. Ground / thermal vias are critical for the proper performance of this device. Vias should use a 0.5 mm(A) diameter drill and have a final plated thru diameter of 0.3 mm(B). ●website: www.berex.com ● email: [email protected] 23 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Tape & Reel Preliminary Datasheet QFN 5x5 Packaging information : Tape width(mm) : 12 Reel Size (inches) : 7 Device Cavity Pitch(mm) : 8 Devices Per Reel : 1000 Lead plating finish 100% Tin Matte finish (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns.) BeRex ●website: www.berex.com ● email: [email protected] 24 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C BMT332 700-2400 MHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Package Marking YY = Year, WW = Working Week, XX = Wafer No. MSL / ESD Rating ESD Rating: Class 1C Value: Passes ≥ 1000V to < 2000 V Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114B ESD Rating: Class C3 Value: Passes >1000V Test: Charged Device Model (CDM) Standard: JEDEC Standard JESD22-C101F MSL Rating: Standard: Level 1 at +260°C convection reflow JEDEC Standard J-STD-020 NATO CAGE code: 2 BeRex N 9 6 F ●website: www.berex.com ● email: [email protected] 25 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2013 BeRex Rev. C