BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Device Features Preliminary Datasheet +5V/550mA at operating bias condition Gain = 25.5 dB @ 2.65 GHz P1dB = 33.5 dBm @ 2.65GHz LTE 10M ACLR = 22.7dBm Output Power at -50dBc @ 2.65GHz Intergrated interstage matching Lead-free/Green/RoHS-compliant QFN5x5 SMT package Product Description Typical Performance1 The BMT333 is a high dynamic range twostage power amplifier housed in a leadfree/green/RoHS compliant 5x5mm QFN package. The BMT333 uses a high reliability InGaP/GaAs HBT process technology. The BMT333 is designed for use where high linearity and gain are required. The BMT333 is able to deliver over 22 dBm output power from 1.8 to 2.7GHz while maintaining superior ACLR performance with a few external matching components. All devices are 100% RF/DC screened. Applications Parameter Frequency 1.8 2.35 Unit 2.55 2.65 GHz Gain 29.7 27.4 26.2 25.5 dB S11 -23.4 -25.8 -23.1 -19.3 dB -12.4 -19.8 -17.0 -18.7 dB OIP3 P1dB 45.1 32.9 50 34.1 48.3 33.3 48.2 33.5 dBm dBm LTE 10M ACLR 22.0 23.5 23.0 22.7 dBm WCDMA ACLR 22.9 5.9 24.4 5.3 23.9 5.0 23.7 5.1 dBm dB S22 2 Noise Figure 1 Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω 2 OIP3 _ measured on two tones with a output power 23dBm/ tone , F2—F1 = 1 MHz.. Base station/Repeaters Infrastructure/Small Cell *ACLR Channel Power measured at -50dBc. Commercial/Industrial/Military wireless system - WCDMA set-up: 3GPP WCDMA, TM1+64DPCH, +5MHz offset, PAR 9.78 at 0.01% Prob. - LTE set-up: 3GPP LTE, FDD E-TM3.1, 10MHz BW, ±5MHz offset, PAR 9.75 @0.01% Prob. Min. LTE / WCDMA /CDMA Wireless Infrastructure Application Circuits Bandwidth Ibias @ (IREF1&2 + IB1&2) IC @ (IC1 + IC2) VCC/Vbias RTH Typical Max. Unit 2.7 GHz mA mA V °C/W 1.8 27 550 5.0 8.7 Absolute Maximum Ratings Parameter Operating Case Temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power Rating -40 to +85 -55 to +155 +200 Unit °C °C °C +6 2 20 V A dBm *Operation of this device above any of these parameters may result in permanent damage. BeRex ●website: www.berex.com ● email: [email protected] 1 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Pin Configuration Pin No. Label 1 IREF1 4,5 RF IN 6 VCC1 11,12,13 RF OUT/VCC2 16 VB2 19 IREF2 20 VB1 2,3,7,8,9,10,14, 15,17,18 Backside Paddle V-I Characteristics GND GND BeRex Evaluation Board Figure about the reference position of components BeRex ●website: www.berex.com ● email: [email protected] 2 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Typical Device Data Preliminary Datasheet S-parameters (Vcc & VBias = +5V, Icq=550mA, Ta=25°C) BeRex S-Parameter (Vcc & VBias = +5V, Icq = 550mA, Ta= 25 °C, calibrated to device leads) Freq [GHz] S11 [Mag] S11 [Ang] S21 [Mag] S21 [Ang] S12 [Mag] S12 [Ang] S22 [Mag] S22 [Ang] 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 0.823 0.829 0.829 0.837 0.840 0.839 0.834 0.834 0.834 0.833 48.909 39.208 29.005 19.120 9.645 0.350 -8.866 -17.528 -26.175 -34.246 8.999 8.410 7.873 7.499 7.353 7.422 7.175 6.794 6.401 5.948 -14.544 -31.779 -48.880 -65.053 -81.298 -101.020 -122.701 -143.783 -164.426 174.823 0.002 0.003 0.002 0.001 0.002 0.004 0.003 0.003 0.002 0.002 -47.886 -54.191 -46.186 -44.098 -103.445 -80.766 -106.587 -39.239 -150.204 -71.305 0.851 0.851 0.855 0.846 0.846 0.843 0.839 0.838 0.833 0.832 56.153 47.807 39.252 30.329 21.294 12.643 3.550 -5.571 -15.217 -25.071 ●website: www.berex.com ● email: [email protected] 3 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 1.8 GHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A 680pF 1nF 1nF N/A 0Ω 2.5pF N/A 4.3pF 3.9pF 1uF 100pF 1nF 10uF 2.2nH 39nH 39nH 150 Ω R2 0603 270 Ω PCB Diagram Tantalum COG/NPO Jumper High Q Cap Tantalum High Q Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 19 Pin 20 Object L1 C8 C10 C3 C5 C4 Distance 1.4mm 3.4mm 2.6mm 6.0mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used 4.3pF(251R14S4R3BV4, EIA 0603) of Johanson Technology. 3.C7 are just jumpers as 0Ω BeRex ●website: www.berex.com ● email: [email protected] 4 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 5 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 6 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 2.35 GHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A 680pF 1nF 1nF 27pF 0Ω 1.2pF 1.2pF 3.3pF 10pF 1nF 100pF 1nF 10uF N/A 0Ω 18nH 150 Ω R2 0603 270 Ω PCB Diagram Tantalum COG/NPO COG/NPO Jumper High Q Cap Tantalum Jumper High Q Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C4 Distance 4.0mm 3.0mm 1.2mm 6.2mm 5.0mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used 3.3pF(251R14S3R3BV4, EIA 0603) of Johanson Technology. 3.C7 & L2 are just jumpers as 0Ω BeRex ●website: www.berex.com ● email: [email protected] 7 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 8 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 9 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 2.55 GHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF 1nF 680pF N/A 1nF 27pF 0Ω 1.0pF 1.5pF 3.0pF 10pF 1nF 100pF 1nF 10uF N/A 0Ω 18nH 150 Ω R2 0603 270 Ω PCB Diagram Tantalum COG/NPO COG/NPO Jumper High Q Cap Tantalum Jumper High Q Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C4 Distance 4.1mm 2.2mm 1.8mm 3.0mm 2.0mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used 3.0pF(251R14S3R0BV4, EIA 0603) of Johanson Technology. 3.C7 & L2 are just jumpers as 0Ω BeRex ●website: www.berex.com ● email: [email protected] 10 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 11 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 12 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Application Circuit: 2.65 GHz Preliminary Datasheet Schematic Diagram BOM Marks C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 L1 L2 L3 R1 1206 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 0603 1206 0603 0603 1008 0603 10uF N/A 680pF 1nF 1nF 27pF 0Ω 1.0pF 1.2pF 3.0pF 10pF 1nF 100pF 1nF 10uF N/A 0Ω 18nH 150 Ω R2 0603 270 Ω PCB Diagram Tantalum COG/NPO COG/NPO Jumper High Q Cap Tantalum Jumper High Q Coil ±5% ±5% Notice Below information is subject to change as conditions of the substrate. Reference Input pin Input pin Output pin Pin 16 Pin 16 Pin 19 Pin 20 Object C8 C9 C10 C3 C6 C5 C4 Distance 3.6mm 2.8mm 0.8mm 6.2mm 2.2mm 1.0mm 5.0mm 1. Pin 16 & 20 is used for Vce of the inner bias circuit. To eliminate bias line resonance you need above 10mm transmission line and adjust the position of C2, C3, C4 ,C5 and C6. Also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. C10 : We recommend High-Q capacitor for better output power performance. In this document we used 3.0pF(251R14S3R0BV4, EIA 0603) of Johanson Technology. 3.C7 & L2 are just jumpers as 0Ω BeRex ●website: www.berex.com ● email: [email protected] 13 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 14 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Typical Performance BeRex 3GPP WCDMA TM1 +64DPCH 1FA 3GPP LTE E-TM3.1 10MHz 3GPP WCDMA TM1 +64DPCH 4FA 3GPP LTE E-TM3.1 20MHz ●website: www.berex.com ● email: [email protected] 15 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Package Outline Dimension BeRex ●website: www.berex.com ● email: [email protected] 16 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet Suggested PCB Land Pattern and PAD Layout • Notes 1. Use 1 oz. copper minimum for top and bottom layer metal. 2. A heatsink underneath the area of the PCB for the mounted device is required for proper thermal operation. 3. Ground / thermal vias are critical for the proper performance of this device. Vias should use a 0.5 mm(A) diameter drill and have a final plated thru diameter of 0.3 mm(B). Package Marking YY = Year, WW = Working Week, XX = Wafer No. BeRex ●website: www.berex.com ● email: [email protected] 17 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Tape & Reel Preliminary Datasheet QFN 5x5 Packaging information : Tape width(mm) : 12 Reel Size (inches) : 7 Device Cavity Pitch(mm) : 8 Devices Per Reel : 1000 Lead plating finish 100% Tin Matte finish (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns.) BeRex ●website: www.berex.com ● email: [email protected] 18 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A BMT333 1.8-2.7 GHz 2W High Linearity 5V 2-Stage Power Amplifier Preliminary Datasheet MSL / ESD Rating ESD Rating: Class 1C Value: Passes ≥ 1000V to < 2000 V Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114B ESD Rating: Class C3 Value: Passes >1000V Test: Charged Device Model (CDM) Standard: JEDEC Standard JESD22-C101F MSL Rating: Level 1 at +260°C convection reflow Standard: JEDEC Standard J-STD-020 NATO CAGE code: BeRex 2 N 9 6 F ●website: www.berex.com ● email: [email protected] 19 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2014 BeRex Rev. A