Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors ® Type 725M Orange Drop Metallized Polypropylene Film Capacitors Features • Radial-lead • Pressed profile, compact size • Non-inductively wound • Very low ESR/ESL • Self-healing properties Specifications Capacitance Range: .01 to 4.7µF Capacitance Tolerance: ±5%, ±10% (other tolerances available upon request) Voltage Ratings: 160 to 630 Volts D-C 100 to 250 Volts A-C Operating Temperature Range: -55°C to +85°C (at full voltage) Voltage Derating: At +105°C, 50% of +85°C rating. Dissipation Factor: 0.1% Maximum @ 1 KHz, +25°C (contact us for additional details on specific capacitance and voltage ratings.) Corona Start Voltage (typical): 160 VDC units: 250 Volts RMS 250 VDC units: 275 Volts RMS 400 VDC units: 300 Volts RMS 630 VDC units: 325 Volts RMS Insulation Resistance: At +25°C: 200,000 M for C 0.5 µF 100,000 M-µF for C > 0.5 µF At +85°C: 10,000 M for C 0.5 µF 5,000 M-µF for C > 0.5 µF Pulse Rise Time (dV/dt): See standard ratings table. dV/dt rating is in Volts/µsec. Encapsulation: Conformal coating of orange, flame retardant epoxy. Meets UL94V-0 specifications. Lead Wire: Tinned copper-clad steel, .032 (0.8) diameter, #20 AWG. Dielectric/Construction: Metallized Polypropylene film, single section design. Non-inductively wound. Dimensions in inches, metric (mm) in parenthesis. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors Ordering/Part Number Information 725M 334 9 2 J B 3 (XXXX) A suffix may be added by the factory to denote special construction. Lead Length 1 = 0.187 (4.7) ± 0.030 (0.8) 2 = 0.250 (6.4) ± 0.030 (0.8) 3 = 1.250 (32) Minimum Custom lead lengths available upon request. Terminal A = Straight Lead B,F = Hairpin Crimp G = Hockey Stick Crimp Case Code See Standard Sizes/Ratings Table D-C Voltage Rating 1 = 160 VDC 2 = 250 VDC 4 = 400 VDC 6 = 630 VDC Capacitance Tolerance 9 = ±10%; 5 = ±5% Capacitance Expressed in Picofarads. The first two digits are the significant figures, the third is the number of zeros following. (i.e. 334 = 330000 pF = .33 µF) CDE Type Number Identifies the basic capacitor design. Standard Marking Format Sample Marking on unit CDE725M250V 334K 9910 Description CDE 725M 250V 334K 9910 - CDE Electronics identification - Type number D-C Voltage rating, Volts - Capacitance and tolerance code - Weekly date code (i.e. 10th week of 1999) Tolerance codes per EIA Standards J K ±5% ±10% CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors Standard Lead Styles TERMINAL B,F TERMINAL A TERMINAL G Standard Lead Spacings CASE CODE N J R L Term. A 0.394 (10.0) 0.590 (15.0) 0.886 (22.5) 1.083 (27.5) Term. B 0.394 (10.0) 0.590 (15.0) 0.886 (22.5) 1.083 (27.5) Term. F 0.295 0.394 0.590 0.886 (7.5) (10.0) (15.0) (22.5) Term. G 0.197 (5.0) 0.295 (7.5) 0.394 (10.0) 0.590 (15.0) CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors Type 725M Standard Sizes/Ratings Value (µF) 1 Part Number LMAX T MAX H MAX dV/dt Value Volts/µsec (µF) 160 VDC / 100 VAC* 1 Part Number LM AX TM AX HM A X dV/dt Volts/µsec 250 VDC / 160 VAC* 0.1 0.12 0.15 0.18 725M10491N 725M12491N 725M15491N 725M18491N .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .21 (5.3) .26 (6.6) .22 (5.9) .24 (6.1) .39 (9.9) .43 (10.9) .49 (12.4) .51 (13.0) 55 64 73 79 0.22 0.25 0.27 0.3 0.33 0.39 0.43 0.47 0.5 0.56 0.62 0.68 725M22491J 725M25491J 725M27491J 725M30491J 725M33491J 725M39491J 725M43491J 725M47491J 725M50491J 725M56491J 725M62491J 725M68491J .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .20 (5.1) .21 (5.3) .21 (5.3) .22 (5.6) .23 (5.8) .25 (6.4) .26 (6.6) .28 (7.1) .28 (7.1) .30 (7.6) .32 (8.1) .33 (8.4) .46 (11.7) .48 (12.2) .48 (12.2) .49 (12.4) .50 (12.7) .52 (13.2) .54 (13.7) .55 (14.0) .56 (14.2) .57 (14.5) .59 (15.0) .60 (15.2) 30 33 35 37 38 41 42 43 44 45 46 47 0.75 0.82 0.9 1.0 1.2 1.5 1.8 2.0 2.2 725M75491R 725M82491R 725M90491R 725M10591R 725M12591R 725M15591R 725M18591R 725M20591R 725M22591R 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) .27 (6.9) .28 (7.1) .29 (7.4) .31 (7.9) .34 (8.6) .38 (9.7) .42 (10.7) .44 (11.2) .44 (11.2) .54 (13.7) .55 (14.0) .57 (14.5) .58 (14.7) .61 (15.5) .65 (16.5) .69 (17.5) .72 (18.3) .78 (19.8) 25 26 27 27 28 29 30 30 30 2.5 2.7 3.0 3.3 3.6 3.9 4.3 4.7 725M25591L 725M27591L 725M30591L 725M33591L 725M36591L 725M39591L 725M43591L 725M47591L 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) .44 (11.2) .46 (11.7) .48 (12.2) .51 (13.0) .53 (13.5) .52 (13.2) .55 (14.0) .58 (14.7) .71 (18.0) .73 (18.5) .76 (19.3) .78 (19.8) .81 (21.6) .87 (22.1) .90 (22.9) .92 (23.4) 24 24 24 24 24 24 25 25 0.056 0.062 0.068 0.075 0.082 0.09 0.1 0.12 0.15 725M56392N 725M62392N 725M68392N 725M75392N 725M82392N 725M90392N 725M10492N 725M12492N 725M15492N .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .21 (5.3) .21 (5.3) .22 (5.6) .21 (5.3) .22 (5.6) .23 (5.8) .24 (6.1) .26 (6.6) .29 (7.4) .35 (8.9) .38 (9.7) .39 (9.9) .42 (10.7) .43 (10.9) .44 (11.2) .45 (11.4) .47 (11.9) .50 (12.7) 54 61 68 73 77 83 88 95 103 0.18 0.22 0.25 0.27 0.3 0.33 0.39 0.43 725M18492J 725M22492J 725M25492J 725M27492J 725M30492J 725M33492J 725M39492J 725M43492J .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .21 (5.3) .23 (5.8) .25 (6.4) .26 (6.6) .27 (6.9) .28 (7.1) .31 (7.9) .32 (8.1) .48 (12.2) .50 (12.7) .52 (13.2) .53 (13.5) .54 (13.7) .55 (14.0) .58 (14.7) .60 (15.2) 42 46 48 50 51 53 55 56 0.47 0.5 0.56 0.62 0.68 0.75 0.82 0.9 1.0 1.2 725M47492R 725N50492R 725M56492R 725M62492R 725M68492R 725M75492R 725M82492R 725M90492R 725M10592R 725M12592R 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) .26 (6.6) .27 (6.9) .28 (7.1) .30 (7.6) .29 (7.4) .31 (7.9) .32 (8.1) .34 (8.6) .36 (9.1) .39 (9.9) .53 (13.5) .54 (13.7) .56 (14.2) .57 (14.5) .63 (16.0) .64 (16.3) .66 (16.8) .67 (17.0) .69 (17.5) .73 (18.5) 30 30 31 32 33 33 34 34 35 36 1.5 1.8 2.0 2.2 2.5 2.7 3.0 3.3 725M15592L 725M18592L 725M20592L 725M22592L 725M25592L 725M27592L 725M30592L 725M33592L 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) .39 (9.9) .43 (10.9) .45 (11.4) .48 (12.2) .51 (13.0) .53 (13.5) .57 (14.5) .60 (15.2) .73 (18.5) .77 (19.6) .79 (20.1) .82 (20.8) .85 (21.6) .88 (22.4) .91 (23.1) .94 (23.9) 28 29 29 29 29 29 30 30 * 60 Hz., RMS 1 To complete part number for specific tolerance, terminal style and lead length please refer to Ordering/Part Number Information page. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors Type 725M Standard Sizes/Ratings Value (µF) Part Number1 LM AX TM AX H MAX dV/dt Volts/µsec Value 1 (µF) Part Number 400 VDC / 220 VAC* L MAX T MAX dV/dt H MAX Volts/µsec 630 VDC / 250 VAC* 0.027 0.033 0.039 0.043 0.047 0.05 0.056 0.062 0.068 0.075 0.082 0.09 725M27394N 725M33394N 725M39394N 725M43394N 725M47394N 725M50394N 725M56394N 725M62394N 725M68394N 725M75394N 725M82394N 725M90394N .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .21 (5.3) .21 (5.3) .23 (5.8) .24 (6.1) .24 (6.1) .25 (6.4) .27 (6.9) .28 (7.1) .27 (6.9) .28 (7.1) .29 (7.4) .31 (7.9) .36 (9.1) .42 (10.7) .43 (10.9) .44 (11.2) .45 (11.4) .46 (11.7) .47(11.9) .49 (12.4) .54 (13.7) .55 (14.0) .57(14.5) .58 (14.7) 90 110 124 132 138 142 149 155 159 164 166 171 0.1 0.12 0.15 0.18 0.22 0.25 0.27 0.3 725M10494J 725M12494J 725M15494J 725M18494J 725M22494J 725M25494J 725M27494J 725M30494J .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .22 (5.6) .24 (6.1) .27 (6.9) .29 (7.4) .32 (8.1) .34 (8.6) .36 (9.1) .38 (9.7) .49 (12.4) .51 (13.0) .54 (13.7) .56 (14.2) .60 (15.2) .62 (15.7) .63 (16.0) .65 (16.5) 61 66 72 75 78 80 81 82 0.33 0.39 0.43 0.47 0.5 0.56 0.62 0.68 0.75 0.82 0.9 725M33494R 725M39494R 725M43494R 725M47494R 725M50494R 725M56494R 725M62494R 725M68494R 725M75494R 725M82494R 725M90494R 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) .30 (7.6) .33 (8.4) .34 (8.6) .36 (9.1) .37 (9.4) .39 (9.9) .41 (10.4) .41 (10.4) .43 (10.9) .45 (11.4) .47 (11.9) .57 (14.5) .60 (15.2) .62 (15.7) .63 (16.0) .64 (16.3) .67 (17.0) .69 (17.5) .75(19.1) .77 (19.6) .79 (20.1) .81 (20.6) 43 45 46 46 47 48 48 48 49 49 1.0 1.2 1.5 725M105941 725M12594L 725M15594L 1.23 (31.2) .44 (11.2) .78 (19.8) 1.23 (31.2) .48 (12.2) .82 (20.8) 1.23 (31.2) .54 (13.7) .89 (22.6) 38 39 39 50 0.01 0.012 0.015 0.018 0.022 0.025 0.027 0.033 0.039 0.043 0.047 0.05 0.056 0.062 725M10396N 725M12396N 725M15396N 725M18396N 725M22396N 725M25396N 725M27396N 725M33396N 725M39396N 725M43396N 725M47396N 725M50396N 725M56396N 725M62396N .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .52 (13.2) .21 (5.3) .23 (5.8) .23 (5.8) .25 (6.4) .27 (6.9) .29 (7.4) .27 (6.9) .30 (7.6) .33 (8.4) .35 (8.9) .36 (9.1) .37 (9.4) .40 (10.2) .42 (10.7) .35 (8.9) .37 (9.4) .43 (10.9) .45 (11.4) .48 (12.2) .49 (12.4) .55 (14.0) .58 (14.7) .60 (15.2) .62 (15.7) .64 (16.3) .65 (16.1) .67 (17.0) .69 (17.5) 161 196 232 256 279 291 297 312 322 328 332 335 340 344 0.068 0.075 0.082 0.09 0.1 0.12 0.15 725M68396J 725M75396J 725M82396J 725M90396J 725M10496J 725M12496J 725M15496J .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .73 (18.5) .27 (6.9) .28 (7.1) .30 (7.6) .31 (7.9) .33 (8.4) .36 (9.1) .40 (10.2) .54 (13.7) .56 (14.2) .57 (14.5) .58 (14.7) .60 (15.2) .63 (16.0) .68 (17.3) 115 118 120 123 125 129 133 0.18 0.22 0.25 0.27 0.3 0.33 0.39 0.43 0.47 0.5 725M18496R 725M22496R 725M25496R 725M27496R 725M30496R 725M33496R 725M39496R 725M43496R 725M47496R 725M50496R 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) 1.03 (26.2) .33 (8.4) .34 (8.6) .36 (9.1) .38 (9.7) .40 (10.2) .42 (10.7) .46 (11.7) .48 (12.2) .51 (13.0) .52 (13.2) .60 (15.2) .67 (17.0) .70 (17.8) .71 (18.0) .74 (18.8) .76 (19.3) .80 (20.3) .82 (20.8) .85 (21.6) .87 (22.1) 68 70 72 72 73 74 75 75 76 76 0.56 0.62 0.68 0.75 725M56496L 725M62496L 725M68496L 725M75496L 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) 1.23 (31.2) .48 (12.2) .51 (13.0) .54 (13.7) .57 (14.5) .82 (20.8) .85 (21.6) .88 (22.4) .91 (23.1) 58 58 59 59 * 60 Hz., RMS 1 To complete part number for specific tolerance, terminal style and lead length please refer to Ordering/Part Number Information page CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors RMS Voltage vs. Frequency @ +85°C, in still air CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors RMS Voltage vs. Frequency @ +85°C, in still air CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type 725M, Orange Drop®, Metallized Polypropylene Film Capacitors General Specifications ® The Type 725M Orange Drop is designed and manufactured for operation in a wide range of demanding environments and applications. Type 725M capacitors are wound from the most reliable metallized polypropylene film available and are protected by a rugged conformal coating of orange epoxy. They may be operated up to +105°C with proper derating. The 725M series is an ideal choice for a variety of commercial and industrial electronic applications, from power supplies and amplifiers, to inverters and lighting ballasts. The 725M series is constructed of the highest quality polypropylene film with a vacuum deposited metal electrode. Metallized film offers specific clearing/ self-healing characteristics that remove a fault or short in the dielectric film by vaporizing the metal electrode surrounding the defect and isolating the area. Operating Temperature Range: The standard operating temperature range for polypropylene film is -55°C to +85°C. The 725M may be operated at full voltage within this temperature range. The 725M may be operated up to +105°C provided the DC working voltage is reduced to 50% of the +85°C rating (full rating). For more specific details regarding operation above +85°C please contact our application engineering department. The maximum operating temperature for the 725M series is +105°C. Dielectric Withstanding Voltage: Units shall withstand a DC potential of 150% of rated voltage applied between terminals for not more than 2 minutes. AC Voltage Applications: The A-C component of the 725M's voltage rating has been specified to assure that corona will not be encountered when the capacitor is operated within the noted specifications. We encourage you to contact us if you have any concerns about operating voltage, temperature limits, etc. DC Voltage Life Test: 500 hours at +85°C at 125% of rated voltage. After test; capacitance shall not have changed by more than ±5% of initial value, insulation resistance shall not have decreased by more than 50% of initial requirement and dissipation factor shall not have increased to more than 0.1%. In addition, there should be no open or short circuits, and no sign of visible damage. AC Voltage Life Test: Minimum of 500 hours at +85°C at 60 Hz. AC test voltage applied at 110% of AC rating. After test, capacitance shall not have changed by more than 3%, insulation resistance shall not have decreased by more than 50% of initial requirement, and dissipation factor shall not have changed by more than 0.03%. Measurements made at 1 KHz. Additional Notes: While it is not possible to list every detail of testing that we perform or every combination of capacitance value, tolerance, etc. that is available, we strongly encourage you to please contact us with your specific requirements. Thank you. Lead Bend Test: After 3 consecutive 180° bends. No damage. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 AC Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. 4