Test Procedure for the LC75843UGA Evaluation Board (LC75843UGAGEVB) 1. Recommended Test Setup Power Supply Oscilloscope CH1 CH2 CH3 CH4 Jump socket For example, CH1 : COM1 CH2 : S5 CH3 : S28 CH4 : S2/P2 Figure 1. LC75843UGAGEVB Recommended Test Setup 2. Test Equipment Table 1. Required Equipment Equipment Efficiency Power supply Oscilloscope 10V, 0.5A 4 channel 3. Test Procedure (1) Connect the test setup as shown in figure 1. (2) Insert the jump sockets of the JP5V, JPGND, JPINH, JPCE, JPCL, JPDI, JPUP, JPP1, JPP2, JPP3 and JPP4, and remove the jump sockets of the DT0, DT1, JP38K and JP300K. (3) The power supply of the evaluation board is turned on by moving “POWER” switch to the “ON” position. (The red monitor LED of the “POW” turns on) (4) An automatic demonstration mode is selected by moving “DEMO mode” switch to the “9” position. Table 2. Setting Contents of the “DEMO mode” Rotary Switch DEMO mode 0 1 2 3 4 3/14/2014 Demonstration item LCD display contents LED control contents all OFF test all ON test LCD display test (1) LCD display test (2) Segment test All LED turn off the light. All LED turn on the light. All LED turn off the light. All LED turn off the light. LED does on in turn. When COM1 is on, LED turn on the light. Any PWM duty are selected by the switches from W0 to W5. (LED1 to LED3 can set same duty) Any PWM duty are selected by the switches from W0 to W5. (LED1 to LED3 can set each duty) 5 Common test 6 LED(PWM) test (1) All segments are off. All segments are on. The LCD displays a “01234”. The LCD displays a “AbcdE”. The LCD segment displays on in turn. LCD segment corresponding to same COM are all on. The LCD displays a “PWM_1” and a PWM duty value. 7 LED(PWM) test (2) The LCD displays a “PWM_2” and a PWM channel number. 8 Demonstration (1) 9 Demonstration (2) LCD number display count ups every 1sec. The LCD displays a “ AUTO” and a PWM duty value. -1- LED does on in turn every 1sec. PWM duty changes every 100msec. www.onsemi.com (5) Set the following switches. About the setting contents details of the switch, refer to User's Manual. Table 3. Setting Contents of the Toggle Switch Switches PF0 to PF3 FC0 to FC3 P1 EXF OC SC BU W0 to W5 Functions Contents which are set The PWM output waveform frame frequency is 195 PWM output waveform frame frequency select. [Hz] by moving “PF0, PF1, PF2, PF3” switch to the “L(0), L(0), L(0), L(0)” position. The common/segment output waveform frame Common/Segment output waveform frame frequency frequency is 97 [Hz] by moving “FC0, FC1, FC2, select. FC3” switch to the “L(0), H(1), L(0), H(1)” position. L(0) : Low level output mode General-purpose output port (S1/P1) function select. H(1) : High level output / Clock output mode External clock operating frequency mode select at L(0) : 300kHz input operating mode OC=H(1). H(1) : 38kHz input operating mode L(0) : Internal oscillator clock operating mode Fundamental clock operating mode select. H(1) : External clock operating mode L(0) : Normal display mode Display on/off select. H(1) : All segments are OFF display mode L(0) : Normal mode Power saving mode select. H(1) : Power saving mode When switch of the “DEMO mode” is set to “9”, duty of the PWM output waveform is automatically set, PWM output waveform duty select. therefore switches of the “Wo to W5” are set to “L(0), L(0), L(0), L(0), L(0), L(0)” position. (6) The CCB serial data are transferred from a controller circuit to LCD driver IC by pushing the “Command Set” switch. (The green monitor LEDs of the “BUSY” and “INH” turns on) (7) The customer can confirm the movement of the LCD display and LED brightness adjustment by the automatic demonstration. Then, the customer can confirm the waveform of the common outputs (COM1 to COM4), segment outputs (S5 to S24, S28) and general-purpose port outputs (P1 to P4). (The green monitor LED of the “SEND” flashes quickly) For example, when the DEMO mode is “9” • The green monitor LED of the “SEND” flashes quickly. • The customer can confirm that a “AUTO” characters and a PWM duty value are displayed to LCD. to • The customer can confirm that LEDs from P1 to P4 change brightly gradually. 3/14/2014 -2- www.onsemi.com