KBL400 - KBL410 SILICON BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 4.0 Amperes KBL 0.77 (19.56) 0.73 (18.54) FEATURES : * * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Ideal for printed circuit board Pb / RoHS Free 0.825 (20.95) 0.605 (15.36) + AC AC 1.0 (25.4) MIN. 1.1 (27.94) MIN. 0.052 (1.32) 0.048 (1.22) MECHANICAL DATA : * Case : Molded plastic * Epoxy : UL94V-O rate flame retardant * Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 5.15 grams 0.085 (2.16) 0.065 (1.65) 0.265 (6.73 ) 0.235 (5.97) 0.200 (5.08) 0.190 (4.82) Dimensions in inches and ( millimeter ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL KBL 400 KBL 401 KBL 402 KBL 404 KBL 406 KBL 408 KBL 410 UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage RATING VRMS 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 V Maximum Average Forward Current Tc=50°C IF(AV) 4.0 A IFSM 200 A I2t 166 A2S Maximum Forward Voltage per Diode at IF = 4 A VF 1.1 V Maximum DC Reverse Current Ta = 25 °C IR 10 µA at Rated DC Blocking Voltage Ta = 100 °C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Rating for fusing ( t < 8.3 ms. ) Typical Thermal Resistance ( Note 1 ) Operating Junction Temperature Range Storage Temperature Range IR(H) 1.0 mA RθJA 10 °C/W TJ - 50 to + 150 °C TSTG - 50 to + 150 °C Note : 1 ) Thermal resistance from Junction to Ambient with units mounted on a 3" X 3" X 0.11" THK ( 7.5cm X 7.5cm X 0.3cm ) Cu. plate. Page 1 of 2 Rev. 02 : March 24, 2005 RATING AND CHARACTERISTIC CURVES ( KBL400 - KBL410 ) FIG.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 200 Mounted on 3" X 3" X 0.11" THK ( 7.5cm X 7.5cm X 0.3cm ) Cu. plate. 3.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 4.0 2.0 1.0 175 150 TJ = 55 °C 125 100 75 50 8.3 ms SINGLE HALF SINE WAVE JEDEC METHOD 25 60 Hz, Resistive or inductive load. 0 0 0 25 50 75 100 125 150 175 1 CASE TEMPERATURE, ( °C) 4 6 10 20 40 60 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FIG.3 - TYPICAL FORWARD CHARACTERISTICS PER DIODE 100 FORWARD CURRENT, AMPERES 2 NUMBER OF CYCLES AT 60Hz Pulse Width = 300 µs 1 % Duty Cycle 10 1.0 TJ = 25 °C 0.1 10 TJ = 100 °C 1.0 TJ = 25 °C 0.1 0.0 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0.4 06 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 02 : March 24, 2005