QS6400 - Altonics

QS6400
Datasheets
64 Poly ADPCM Sound Synthesizer For Mobile Phone.
Version 2.0
Contents
Chapter 1 General Description
Chapter 2 Features
Chapter 3 Block Diagram
3-1 Outline of Block
3-2 Description of blocks
Chapter 4 Pin Rotation and Pin Description
4-1 Pin Rotation
4-2 Pin Descriptions
4-3 Detail Pin Description
Chapter 5 Details of Block
5-1 Register
5-1-1 Register Table
5-1-2 Read and Write Operation
5-1-3 Deatailed Register Description and Usage Each Action.
5-2 FIFO
5-3 D/A Interfacing
5-4 PWM Output
Chapter 6 Application Flow Chart
Chapter 7 Electrical Charateristics and soldering temperature
Chapter 8 SMF Sound Table
Chapter 9 Outline Dimensions and weight
Chapter 10 Marking
1/37
HWA SOUND SOURCE
Chapter 1
Advanced ADPCM SOUND DSP for Mobile
QS6400
General Description
QS6400 is a high quality sound DSP for mobile phones that plays music through a built-in
ADPCM decoder with sound font rom.
QS6400 is equipped with HWASS's QPCM synthesizer,which is capable of generating up to 64 voices
with different tones.
QS6400 can also play two channel wavefiles of differing sampling rates.
Since data in the FIFO buffer is processed on demand, the length of the data(MIDI & WAVE) is not limited,
making QS6400 an excellent platform for applications such as incoming melody distribution service.
The MIDI handler built in to QS6400 can play MIDI data without an extra buffer.
Included is a PWM module for audio out with a maximum output of 400mw at 8Ω load registance(PVDD=4.0V
For earphone use, QS6400 provides a single-ended stereophonic output terminal.
To operate QS6400 to full capability, "Standard MIDI File(SMF) Format 0" is recommended.
Chapter 2
Features
ADPCM synthesizer functions
▶ 64 voices generated at 39kH simultaneously.
▶ Compatible with stereophonic sound generation.
▶ Master Volume control
Individual channel volume / master volume.
▶ Built-in MIDI handler(sequencer)
▶ Equipped with two buffers of 128 bytes FIFO for MIDI play.
▶ Built-in 4 bit or 8 bit ADPCM decorder.
TONE
▶ Supports GENERAL MIDI LITE specification.
GM 128 voices + 47 voices percussion.
Support to control parameters by "BxH xxh"(see the MIDI implementation chart)
▶ Additional 8 timbres to play korean traditional music.
Gayagum/Daegum/Heagum/Teapyoungso/Buk/Ggangary/Jangu/Jing.
▶ Various sampling rate : 8 ~ 39Khz
WAVE
▶ Support to playback ADPCM wavefile(2 Channels)
▶ Separate wave volume control(0~255)
CPU INTERFACING
▶ 1 Wire serial or 14 Wires parallel interfacing can be selected.
2/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
AUDIO OUTPUT
▶ PWM or 16bit DAC output can be selected.
▶ PWM output mode : 400mW when PVDD=4.0V, RL=8Ω
▶ Provides Stereo or Mono output for earphone.
POWER SUPPLY
▶ Includes three power supplies for sub-system
PVDD power supply devoted to PWM block.(3.3 ~ 4.2V)
EVDD power supply devoted to earphone block.(2.7 ~ 3.6V)
VDD is normal power supply.(2.7 ~ 3.6V)
3/37
HWA SOUND SOURCE
Chapter 3
Advanced ADPCM SOUND DSP for Mobile
QS6400
Block Diagram
3-1. Outline of Blocks
D0~D7 WRB
D0~D7
RDB
Register
32 * 8
CSB
A0
CPU & ROM
SMFSMFBuffer
Buffer
128
* 88
128*
FIFO
FIFO
4Mbit Built In
Sound Font ROM
Wave
Wave
Wave
Wave
Buffer
Buffer
Buffer
Buffer
6464*64
8
64***888
FIFO
FIFO
FIFO
FIFO
WAKEB
XIN
XOUT
MIDI IRQB MRSTB
Sound Memory Interface
SMF file
Decorde
r
&
Power
Control
Vibrato & LFO
ADPCM
Wave
Clock
Generater
Digital Filter
Decoder
Mixing & Panning
D/A Interface
EarPhone OUT
SPK out ( PWM L
SPK out ( PWM R )
MUX
MUX
SOUT
Right Left EVDD
PWML( - )
PWML( + )
PWMR( - )
PWMR( + )
(*Wclk)(*Sclk)
4/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
3-2. Descripion of Blocks
Explanations about each block of QS6400 and flows of the signal are as follows.
1) Register Block : QS6400 has registers of 32 x 8 for storing control data.
Built-in 8052 can communicate directly with the register blocks,
which are used to change control values and communicate commands.
23 x 8 registers are used for this purpose.
The extra registers are available to support additional features.
2) SMF FIFO buffer : This FIFO is used in receiving SMF file blocks (128bytes) from Host.
SMF FIFO Buffer has two banks of memory block and each buffer is filled with data
according to REG_IREQ_TYPE (When bit 2 is "1" ) from built- in 8052.
When receiving a data request (IRQB) for the next procedure you should read the
interrupt request type register (REG_IREQ_TYPE) to check which data is required.
3) WAVE FIFO buffer : This FIFO is used in receiving wave data blocks (64 or 128 bytes)
from Host. WAVE FIFO Buffer has four banks of memory block, of 64 bytes each.
The buffer size is determined by user specification (using REG_WAVE_CHAN).
Each bank is filled with wave data accoding to REG_IREQ_TYPE( when bit 1 or bit 0 is "1
If you intend to play high-sampling-rate(up to 22khz) wave files, we recommend
that you use only one wave channel, due to the high transmission rate of data.
In this case, WAVE FIFO Buffer size is preset to 128bytes.
4) Power control : This block is in charge of power management.
You can select whether to enter or wake-up from power down mode.
5) Clock generator : This block is a clock generator for the internal master clock.
QS6400 need the external clock input to operate normally.
6) CPU & ROM : This block describes 8052 micom and 12k bytes program ROM memory.
Built-in 8052 interprets SMF and Wave file.
7) PWM Speaker out : This block converts audio data into PWM format.
It supports stereophonic audio out.
You can also make this output muted.
8) Earphone out : This block converts audio data into single-ended earphone signal.
You should connect poled-capacitor and bypass capacitor.
P38/P39
Earphone_R/L
1uf/10v
104p
5/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
9) D/A interface : This block generates 16bit DAC interfacing out for high quality sound.
If you have an additonal DAC, you can also use this interfacing out.
When you use the DAC OUT mode, earphone out mode is disabled.
10) Sound font : This is an embedded maskrom for GM 128 sound map and 47 percussion.
The sound font built in this device stores the sampling data according to
GM 128 sound map.
Additionally QS6400 has sampling data to support korean traditional music.
6/37
HWA SOUND SOURCE
Chapter 4
Advanced ADPCM SOUND DSP for Mobile
QS6400
Pin Rotation and Descriptions.
4-1. Pin Rotation
7/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
4-2. Pin Descriptions
PIN NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PIN NAME
NC
NC
VSS
VDD
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
WAKEB
WRB
RDB
IRQB
MIDI
CSB
A0
MRSTB
MODE0
MODE1
TEST
XIN
XOUT
VDD
VSS
NC
NC
VSS
PWML(-)
PWMR(-)
PVDD
PWML(+)
PWMR(+)
PVSS
EarPhone_R(*Wclk)
EarPhone_L(*Sclk)
EVDD
I/O
X
X
P
P
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
O
I
I
I
I
I/O
I/O
I
I
I
P
P
X
X
P
O
O
I
O
O
I
O
O
P
DESCRIPTION
No Connect
No Connect
Ground
Power Supply
Serial Data Out for DAC
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
Bidirection DATA BUS
WakeUp Signal(Active Low)
Write Enable
Read Enable
Request Data Block( Active Low )
MIDI IN ( UART )
Chip Select
Register Address or Data Strobe
Master Reset ( Active Low )
LED control port or test mode
Vibrator control port or test mode
Test Mode Select( must be Low)
Master Clock In
MODE0 and MODE1 I/O select
Power Supply
Ground
No Connect
No Connect
Ground
PWM Output Left (-)
PWM Output Right (-)
PWM Power
PWM Output Left (+)
PWM Output Right (+)
PWM Ground
EarPhone out Right or Word Clock for DAC
EarPhone out Left or Serial Clock for DAC
Power for EarPhone
8/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
4-3. Detail pin descriptions.
▶ POWER SUPPLY PINS
VDD ( 4,27 )
These pins are connected to a normal power supplier.
VSS ( 3,28,31 )
These pins are GNDs of power.
PVDD( 34 ), EVDD( 40 ),PVSS (37)
PVDD is VDD for PWM block. It's capable of driving a voltage of MAX 4.2V down to 3.3V.
EVDD is VDD for EarPhone block. Its range covers 3.6V to 2.7V.
PVSS is PWM block GND.
▶ POWER RESET
MRSTB ( 21 )
Reset is accomplished by holding the MRSTB pin low for at least 60 oscillator periods
while the oscillator is running. To ensure proper power-on reset, the MRSTB pin must be
high long enough to allow the oscillator time to start up plus 40 oscillator periods.
RESET plus should be free from glitch noise.
At power-on, the voltage on VDD and MRSTB must come up at the same time for a proper start-up.
After RESET, all registers and internal RAM are initialized to "0x00".
▶ AUDIO INTERFACE
QS6400 supports two kinds of output mode; DAC out or PWM out
There is a register for selecting output mode.
In using PWM mode, you can select Stereo or Mono out. Thus QS6400 can support application
such as high-quality stereo mobile phones.
QS6400 also provides single-ended stereophonic earphone output, showing superb playback quality
through both External speakers and earphones.
You can select these modes using REG_OUT_MODE.
PWML-( 32 ), PWML+( 35 ), PWMR-(33),PWMR+(36)
QS6400 supports Stereo PWM out for the Speaker. This output can be muted if desired.
PWML- and PWMR- are connected to the speaker's minus(-) terminal.
PWML+ and PWMR+ should be connected to the plus(+) terminal.
EarPhone_R(38), EarPhone_L(39)
EarPhone_R and EarPhone_L are single- Ended Stereo EarPhone output modes.
EVDD is prepared to power earphone operation seperately.
Also you can mute PWM output signal by control bit located in REG_OUT_MODE.
WCLK ( *38 ), SCLK ( *39 ), SOUT ( 5 )
If you write data "1xxxxxxxH" to "(Out_Mode)" after reset, DAC mode is enabled and
Earphone out is disabled.
On the other hand, if you need EarPhone out mode, you can choose EarPhone out Mode.
If you want more detailed information, see "Chapter 5-3 D/A interface and
Chapter 5-4 Earphone out".
9/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
▶ CPU INTERFACE
QS6400 provides 1 wire serial interface and 14 wires parallel interface.
These are processed at the same time without extra control commands.
MIDI ( 18 )
Interface for serial MIDI signal. The input signal should be of asynchronous serial type
with no-parity bit and should have one start and stop bit each, thus consisting
of ten total bits. The transfer mode should be MSB first method.
IRQB ( 17 )
Request pin(IRQB) that is activated when QS6400 is ready to receive next packet data block.
After receiving this request, you must read the interrupt request type register(REG_IREQ_TYPE)
which you want. At this time IRQB is cleared.
To play MIDI file you should transfer 128 byte data blocks.
To play wave files, you should transfer 64 or 128 bytes of data.
You can select the data block size by write value to wave channel number register(REG_WAVE_CH
If you take one wave channel, data block size is 128 bytes.
If you want to play two wavefiles simultaneously. the data block should be 128/2 = 64bytes.
WAKEB ( 14 )
WAKEB is to release from Power-Down Mode. A wake operation is accomplished
by holding the WAKEB pin low for a minimum of 70ns period.
After wakeup, all internal registers and RAM buffers are initialized to zero.
A0( 20 )
This pin is used to select between Register Address or Command and Data. If the pin is high,
the data to be written is the Register Address(Index) . Otherwise if the pin is low, the
data to be written is Command or Data.
CSB( 19 )
Chip Select for QS6400. This pin must be low for read and write operation.
D0~D7(6~13)
These are data buses for INDEX and DATA.
We recommend use of COMMON DATA BUS.
▶ EXTRA PINS
XIN ( 25 )
XOUT ( 26 )
This pin determines I/O status of MODE0 and MODE1. When High, MODE0 and MODE1 are set to
input mode. However, in this case either one of MODE0 or MODE1 must be High.
If both are Low, that signals a self diagnostic mode.
When XOUT is Low, MODE0 and MODE1 are used in output mode, with MODE0 and MODE1
each controling the LED and the Vibrator, respectively.
10/37
HWA SOUND SOURCE
Chapter 5
Advanced ADPCM SOUND DSP for Mobile
QS6400
Details of Blocks.
5-1. REGISTER
5-1-1. REGISTER TABLE
Registers
RESERVED
RESERVED
RESERVED
REG_SMF_CTRL
REG_VOLUME
REG_SMF_EOP
REG_PIO_MIDI
REG_WAVE_CHAN
REG_WAV1_CTRL
REG_WAV_VOL
REG_PTR_FIFO
REG_WAV1_SR
REG_WAV2_CTRL
REG_LED_MODE
REG_VIB_MODE
REG_WAV2_SR
REG_LV_CTRL
REG_SMF_BUF
REG_WAV1_BUF
REG_WAV2_BUF
REG_READY_QS
REG_REF_TUNE
REG_OUT_MODE
REG_P_DOWN
REG_EARP_VOL
REG_PWM_CLOCK
REG_IREQ_TYPE
RESERVED
REG_QDSP_MODE
READ_WRITE_BACK
RESERVED
RESERVED
RESERVED
RESERVED
REG_IF_FLAG1
REG_IF_FLAG2
REG_IF_FLAG3
REG_IF_FLAG4
Address
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
1AH
1BH
1CH
1DH
1EH
1FH
20H
21H
22H
23H
24H
25H
R/W
X
X
X
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
R
X
R
R
X
X
X
X
R
R
R
R
Description
Reserved
Reserved
Reserved
SMF play control register (play/stop/etc.)
PWMR and PWML gain control register
End of a packet(128 bytes) register for the SMF
Parallel MIDI interface register
Register to specify number of wave channels to use
Wave channel 1 play control register
Wave volume control register
Pointer register of the SMF fifo for single midi mode
Wave channel 1 sample rate select register
Wave channel 2 play control register
LED mode select register
Vibrator mode select register
wave channel 2 sample rate select register
Led and vibrator on/off control register
SMF packet block buffer register (128bytes )
Wave channel 1 packet block buffer register
Wave channel 2 packet block buffer register
Ready for active of QS6400
Reference Clock Select
Audio output mode select register
Power down mode register
Earphone volume control register
PWM Clock Rate Selector
Interrupt request type register(Read only)
Reserved
Status bit for SMF & WAVE Channel.(Read only)
Read the INDEX to be written before (Read only)
Reserved
Reserved
Reserved
Reserved
Flag1 register to notify 8-registers writing state
Flag2 register to notify 8-registers writing state
Flag3 register to notify 8-registers writing state
Flag4 register to notify 8-registers writing state
11/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
5-1-2. READ AND WRITE OPERATION
Set Address
Read Register
Write Register
WRB
↑
H
↑
RDB
H
↑
H
A0
H
L
L
CSB
L
L
L
D0 ~D7
Set register address to write or read
Read data from QS6400
Write command to QS6400
To write Data or a Command to a register, first set A0 to High and CSB to low.
After writing the Index Address of target register, set both A0 and CSB to low to write
command or data.
● Read Command Flow
Set Register
Read Status
● Write Command Flow
Set Register
Write Data or Command
5-1-3. DETAILED REGISTER DECRIPTIONS AND USEAGES IN EACH ACTION
▶ INITAIL SETUP WHEN POWER ON RESET.
1) RELATED TO DEVICE READY CHECK BETWEEN HOST AND QS6400
REG_READY_QS : 0x14
Data
Description
0x4D
Ready command for ACTION of QS6400
This register relays an initialization signal to the QS6400.
For normal initialization write “0x4D”.
*Warning => This register is also used to test the operation of the chip, and any other
value should not be written to it
REG_QDSP_MODE : 0x1C
Internal operation status of QS6400
Bit 0
H
L
Bit 1
H
L
Bit 2
H
L
Bit 3
H
L
H
Bit 4
L
H
Bit 5
L
H
Bit 6
L
Bit 7
H
L
Ready Wave Channel #1
Busy Wave Channel #1
Ready Wave Channel #2
Busy Wave Channel #2
fade out complete mode by power down
normal mode
midi file play mode
midi file stop mode
not used
reserved
single MIDI protocol FIFO mode
normal FIFO using mode
abnormal wake up mode
normal wake up mode
normal wake up mode
abnormal wake up mode
12/37
HWA SOUND SOURCE
Read and Check
Host
"0x4D" write
Advanced ADPCM SOUND DSP for Mobile
"10xxxxxxB" write
QDSP MODE
REGISTER
READY_QS Read and ready to action
REGISTER
"QS6400"
QS6400
Micom in
QS6400
2) RELATED TO QS6400 INITIAL VALUE
REG_VOLUME : 0x04
DATA
Description
0x00 ~ OxFF
PWMR and PWML gain control
This register adjusts the output gain on Speaker driven by internal amplifier of QS6400.
Valid range is 0~255. User sets this value according to desired output.
REG_WAVE_CHAN : 0x07
DATA
0x00
0x01
Description
Do not use any Wave(ADPCM) decoder channels.
Use one Wave(ADPCM) decoder channel.On request of Wave
Data Packet, 128 bytes must be transferred.
0x02
Use two Wave(ADPCM) decoder channels.On request of
Wave Data Packet, 64 bytes must be transferred.
The number of ADPCM decoder channels to be used during ADPCM wave file playback
is decided by this register. The internal Wave FIFO buffer is utilized differently
depending on this value.
REG_WAV_VOL : 0x09
DATA
Description
0x00 ~ 0xFF
Set Wave Play Volume for Wave Channels
Sets the volume of the ADPCM decoder. Range is 0~255.
REG_EARP_VOL : 0x18
Bit7
Description
1
Earphone Out Left Volume. Range : 0 ~ 127(Bit6 ~ Bit0)
0
Earphone Out Right Volume. Range : 0 ~ 127(Bit6 ~ Bit0)
This register sets earphone out volume.
REG_PWM_CLOCK : 0x19
DATA
Description
0x00
40Mhz for PWM drive clock
0x01
20Mhz for PWM drive clock
Register to select internal clock mode to drive PWM.
13/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
3) AUDIO OUT SELECT REGISTER
REG_OUT_MODE : 0x16
DATA
Bit 7
Description
L
Select PWM for Audio out
H
Select DAC for Audio out
L
Bit 6
Set PWM out Enable
H
Set PWM out Disable(Mute)
Bit 5
Undefined
L
Undefined
H
L
Bit 4
Set Stereo Mode
H
Set Mono Mode
L
Undefined
Bit 3
H
Undefined
Earphone Right Out Enable
L
Bit 2
H
Earphone Right Out Disable(Mute)
L
Earphone Left Out Enable
Bit 1
Earphone Left Out Disable(Mute)
H
Undefined
x
Bit 0
Sets stereo/mono mode of Audio out and also enables/disables mute for each output signal.
4) REFERENCE CLOCK SELECT REGISTER
REG_REF_TUNE : 0x15
This register is used to correct the internal clock that is generated in tandem to the
external reference clock. It has to be set to the correct value according to the clock
frequency received on Xin. A disparage between the frequency of clock value set in this
register and Xin will result in sounds of abnormal pitch and tempo.
Values for each frequency are as follows:
DATA
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Xin Reference Clock
Reference Clock = 13Mhz
Reference Clock = 19.2Mhz
Reference Clock = 26Mhz
Reference Clock = 24Mhz
Reference Clock = 13Mhz
Reference Clock = 19.2Mhz
Reference Clock = 26Mhz
Reference Clock = 24Mhz
Reference Clock = 13Mhz
Reference Clock = 19.68Mhz
Reference Clock = 26Mhz
Reference Clock = 24Mhz
Reference Clock = 13Mhz
Reference Clock = 19.68Mhz
Reference Clock = 26Mhz
Reference Clock = 24Mhz
14/37
HWA SOUND SOURCE
16 ~ 255
Advanced ADPCM SOUND DSP for Mobile
QS6400
Reference Clock = Register Value / 10
ex) Register Value = 16, Reference Clock = 1.6Mhz
Register Value = 21, Reference Clock = 2.1Mhz
Register Value = 96, Reference Clock = 9.6Mhz
▶ RELATED TO PLAY MIDI REGISTER
REG_SMF_CTRL : 0x03
This register controls Standard MIDI File(SMF) playback.
Operations are decided by bits written to this register.
Function
Data
Description
Starts play of SMF.
Playback
0x11
Stops play of SMF.
0x12
0x13
Pauses play of SMF.
Should only be used during playback.
Tempo
FIFO
Key
Shift
0x14
Resumes play of SMF from pause state.
Should only be used when paused.
0x20
Sets Tempo to base tempo, removing any changes
that have been made to the Tempo.
0x21
Tempo increases in steps of 1% against base tempo, to a
maximum of 25%.(Cannot be used while playing an ADPCM
Wave File)
0x22
Tempo decreases in steps of 1% against base tempo, to a
maximum of 25%.(Cannot be used while playing an ADPCM
Wave File)
0x31
Sets mode of MIDI FIFO buffer to be used as a MIDI protocol
input buffer to an external MIDI sequencer.The internal
sequencer of the QS6400 is disabled in this mode.
0x32
Returns to normal mode, canceling use of the MIDI FIFO
buffer as input to an external sequencer.
0x40
Sets key to base key, removing any changes that have been
made to the key.
0x41
Key is increased by one pitch. Can be increased by a
maximum of 12.
0x42
Key is decreased by one pitch. Can be decreased by a
maximum of 12.
*Tempo step up from original tempo value.( Total 50 steps )
-5%
-1%
1%
Tempo down
5%
Tempo up
Original Tempo
15/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
REG_SMF_BUF : 0x11
Write data to this register during SMF data packet transfer.
For a continuous write, just initiate the first write.
This can also be used as a buffer for direct external input of MIDI protocol data.
DATA
Description
SMF DATA
MIDI Packet Data Buffer Write Address( 128Bytes)
After receiving the next data request. you should write the data to this address
in a block of 128 bytes. And then write dummy data to "REG_SMF_EOP" register
to acquire to finish this packet.
REG_SMF_EOP : 0x05
DATA
ANY DATA
Description
Finished MIDI data write.
This register notifies the transfer of a 128 byte data packet is completed upon request
for the next SMF data packet during playback.
It is only used to control SMF data transfer, and is activated by any non-zero value.
REG_IREQ_TYPE : 0x1A
Determines which request has been made when IRQB pin is Low. Reading this register
resets IRQB to High.
DATA
Description
Bit 0
On request of next data packet of Wave channel 2.
Bit 1
On request of next data packet of Wave channel 1.
Bit 2
On request for next data packet of Song File
Bit 3
Reserved
Bit 4
Reserved
Bit 5
When playback of Song File has ended
Bit 6
Start/Stop of Wave channel 2 during playback of Song File.
Bit 7
Start/Stop of Wave channel 1 during playback of Song File.
( H : request active , L : no request )
1st byte in 2nd packet
< Play SMF sequency >
128 Bytes
WRB
REG
DATA
REG_SMF_BUF
SMF DATA
1 Byte
1 Byte
REG_SMF_EOP REG_SMF_CTRL
DUMMY-DATA
0x11
Start MIDI
SMF_DATA
IRQB
<Next data block request>
Check the REG_IREQ_TYPE which bit 2 is "1" and then
write the packet data to be required.
16/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
< Detailed register control to play the SMF file >
- STEP 1-
REG_SMF_BUF(11H) <----
OxXX ; To write the 1st packet data(128bytes).
- STEP 2-
REG_SMF_CTRL(03H) <----
Ox11 ; Start play of the SMF file.
- STEP 3-
REG_SMF_EOP(05H) <----
OxXX ; Write the dummy data for finishing packet data transfer.
packet data writing
process
- STEP 4-
Check "Data Request"
; Next packet reguest(IRQB) from QS6400
- STEP 5-
REG_IREQ_TYPE(1AH
; Read "REG_IREQ_TYPE" and Check if bit 2 is "1"
- STEP 6-
REG_SMF_BUF(11H) <----
OxXX ; To write the 2nd packet data(128bytes).
- STEP 7-
REG_SMF_EOP(05H) <----
OxXX ; Write the dummy data for finishing packet data transfer.
Repeat packet data writing process
.
"
"
"
"
"
"
"
"
"
.
Repeat packet data writing process
- STEP 8-
Check "Data Request"
; Next packet reguest(IRQB) from QS6400
- STEP 9-
REG_IREQ_TYPE(1AH <----
; Read "REG_IREQ_TYPE" and Check if bit 2 is "SET"
- STEP10-
REG_SMF_BUF(11H) <----
OxXX ; Write the last packet data(128bytes).
- STEP11-
REG_SMF_EOP(05H) <----
OxXX ; Write the dummy data for finishing packet data transfer.
Last packet
- STEP 12- Check "Data Request"
; Next packet reguest(IRQB) from QS6400
- STEP 13- REG_IREQ_TYPE(1AH <----
; Read "REG_IREQ_TYPE" and Check if bit 5 is "SET"
Stop the SMF Play
17/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
▶ RELATED TO PLAY WAVE REGISTER
REG_WAV1_CTRL : 0x08
DATA
Description
0x11
Start decode on Wave Channel 1.
0x12
Stop decode on Wave Channel 1
This controls the ADPCM decoder of the first Wave Channel.
REG_WAV1_SR : 0x0B
Sets type of ADPCM decoder channel 1.
Bit7 ~ Bit6
Bit5 ~ Bit4
Bit3 ~ Bit0
ADPCM table Select
Filter Select or Sub
Sampling Rate Select
Sampling Rate
ADPCM table Select
Filter Select or Sub
Sampling Rate
Select
Bit3 ~ Bit0
Sampling Rate
Bit7
Bit6
0
0
1
1
0
1
0
1
Bit5
Bit4
Description
0
0
1
1
0
1
0
1
Without Filter Mode
Filter 1 Mode
Filter 2 Mode
Sub Sampling Mode
Description
Using
Using
Using
Using
ADPCM
ADPCM
ADPCM
ADPCM
table
table
table
table
1
2
3
4
(19T)
(08T)
(04T)
(02T)
Main Sampling Rate
Sub Sampling Rate
0x00 0x01 0x02 0x03 0x04 0x0A 0x0B 0x0C 0x0D 0x0E
22.1K 14.7K 11K 8.82K 4.41K 8K
7K
6K
5K
3.6K
REG_WAV2_CTRL : 0x0C
DATA
Description
0x11
Start decode on Wave Channel 2.
Stop decode on Wave Channel 2
0x12
This controls the ADPCM decoder of the second Wave Channel.
REG_WAV2_SR : 0x0F
Sets type of ADPCM decoder channel 2.
Bit7 ~ Bit6
Bit5 ~ Bit4
Bit3 ~ Bit0
ADPCM table Select
Filter Select or Sub
Sampling Rate Select
Sampling Rate
18/37
HWA SOUND SOURCE
ADPCM table Select
Filter Select or Sub
Sampling Rate
Select
Bit3 ~ Bit0
Sampling Rate
Advanced ADPCM SOUND DSP for Mobile
Bit7
Bit6
0
0
1
1
0
1
0
1
Bit5
Bit4
Description
0
0
1
1
0
1
0
1
Without Filter Mode
Filter 1 Mode
Filter 2 Mode
Sub Sampling Mode
QS6400
Description
Using
Using
Using
Using
ADPCM
ADPCM
ADPCM
ADPCM
table
table
table
table
1
2
3
4
(19T)
(08T)
(04T)
(02T)
Main Sampling Rate
Sub Sampling Rate
0x00 0x01 0x02 0x03 0x04 0x0A 0x0B 0x0C 0x0D 0x0E
22.1K 14.7K 11K 8.82K 4.41K 8K
7K
6K
5K
3.6K
REG_WAV1_BUF : 0x12 & REG_WAV2_BUF : 0x13
DATA
Description
WAVE DATA
Wave#1/2 Packet Data Buffer (**bytes)
**bytes : If you select one-wave channel, you should write packet data of 128 byte.
If you select two-wave channel, you should write packet data of 64 byte.
< Play the wave sequency >
1 Byte
128(64) Bytes
WRB
REG
DATA
0x00 or 01 or 02
"A"
<Next data block request>
Check the REG_IEQ_TYPE which bit 0 or 1 is
"1" and then write required packet DATA
1 Byte
REG_WAV#1/2_BU
WAV_CTRL#1 or 2#
WAVE_DATA
0x11
Start WAVE
WAVE_DATA
IRQB
"A"
: SET number of WAVE channel.
19/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
< Detailed register control for playing the WAVE file "When wave channel is one" >
- STEP 1-
REG_WAV_VOL(09H) <----
Ox00 ~OxFF ; Set Wave volume
- STEP 2-
REG_WAV1_SR(0BH) <----
Ox00 ~ Ox09 ; Set sampling-rate and number of data bit.
- STEP 3-
REG_WAV1_BUF(12H)<----
OxXX ; Write the packet data for playing wave.(128byte)
- STEP 4-
REG_WAV1_CTRL(08H <----
Ox11 ; Start the WAVE file.
- STEP 5-
Check "Data Request"
; Next packet reguest(IRQB) from QS6400
- STEP 6-
REG_IREQ_TYPE(1AH
; Read "REG_IREQ_TYPE" and Check if bit 1 is "SET"
- STEP 7-
REG_WAV1_BUF(12H)<----
OxXX ; Write the 2nd packet data for playing wave.(128byte)
Repeat packet data writing process
.
"
"
"
"
"
"
"
"
"
Repeat packet data writing process
- STEP 8-
Check "Data Request"
; Next packet reguest(IRQB) from QS6400
- STEP 9-
REG_IREQ_TYPE(1AH
; Read "REG_IREQ_TYPE" and Check if bit 1 is "SET"
- STEP10-
REG_WAV1_BUF(12H)<----
- STEP11- REG_WAV1_CTRL(08H<----
OxXX ; Write the last packet data(128bytes). Last packet data
Ox12 ; STOP the WAVE play.
20/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
▶ RELATED TO ONE NOTE MIDI PLAY
REG_PIO_MIDI : 0x06
Description
DATA
MIDI BYTE
Support to input midi data by parallel format
This register is used for direct input of MIDI protocol by the user.
The data is provided by the user and 0~2mSec are required for data read.
This is useful for producing a Key Tone of a specific sound in the GM sound map.
REG_PTR_FIFO : 0x0A
Used to notify the QS6400 on the 256byte buffer offset Address during transfer on a by
MIDI
protocol data basis, using the SMF FIFO buffer.
▶ POWER MANEGEMENT REGISTER
REG_P_DOWN : 0x17
Puts QS6400 in power down mode.
This is also used to stop internal clock generator adjustment.
DATA
0xAA
0x55
0x01
Description
Enters Power Down Mode
Gradually reduces currently operating Polys. (Fade Out)
Stops internal clock adjustment algorithm
▶ GPIO CONTROL REGISTER
REG_LED_MODE : 0x0D
Sets behavior of LED when controlled using MODE0(#22) pin.
Bit7
Bit6 ~ Bit4
Bit3 ~ Bit0
LED blink frequency
(LED_BF)
*Bit7 must be ‘0’. Setting to ‘1’ signals use of register for sound test, so it must be set to
‘0’ for
this register to be used as a control parameter.
Bit7 = ‘1’, Bit6 = ‘0’: Bit5~Bit0 become internal ENV_ATTENUATE.
Bit7 ‘1’ Bit6 ‘1’ Bit5 Bit0 b
i t
l VOL ATTENUATE
* LED operation Mode
0
Bit6
0
0
0
1
1
Bit5
0
1
1
1
1
etc
LED operation mode
Bit4
0
0
1
0
1
Sync. with LED control
Sync. with LED control
Sync. with LED control + Blinking
Reserved Mode
Reserved Mode
Reserved Mode
* LED blink freq.
Blinking Frequency = 100 / ( 4 x LED_BF) Hz
Will not blink if LED_BF is set to “0”.
21/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
REG_VIB_MODE : 0x0E
Sets behavior of Vibrator when controlled using MODE1(#23) pin.
Bit7
Bit6 ~ Bit4
0
Vibrator operation mode
Bit3 ~ Bit0
Vibrator blink frequency
(VIB_BF)
*Bit7 must be ‘0’. Setting to ‘1’ signals use of register for sound test, so it must be set to
‘0’ for
this register to be used as a control parameter.
Bit7 = ‘1’, Bit6 = ‘0’: Bit5~Bit0 become internal PD_ENV_DECAY.
Bit7 ‘1’ Bit6 ‘1’ Bit5 Bit0 b
i t
l MUTE ENV DECAY
* Vibrator operation Mode
Bit6
0
0
0
1
1
Bit5
0
1
1
1
1
etc
Bit4
0
0
1
0
1
Sync. with Vibrator control
Sync. with Vibrator control
Sync. with Vibrator control + Blinking
Reserved Mode
Reserved Mode
Reserved Mode
* Vibrator blink freq.
Blinking Frequency = 100 / ( 4 x VIB_BF) Hz
Will not blink if VIB_BF is set to “0”.
REG_WRITE_BACK : 0x1D
Returns Register Index Number when QS6400 reads a Command or Data that has previously
been
written to some register.
Used to verify that the internal processor has read some specific value that was written.
22/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
5-2. FIFO
QS6400 have two kinds of FIFO to play MIDI and WAVE DATA.
These FIFOs are prepared for receiving the SMF file and Wave data from Host.
Both of them have two banks of memory block and each buffer is filled with data
according to REG_IREQ_TYPE from built- in 8052.
They both have the same address. Address is automatically incremented during operation.
When receiving the data request(IRQB) for next procedure you should read
the REG_IREQ_TYPE register and then send the next data by request type.
< FIFO for MIDI >
*03H
0
1
2
3
4
5
….
122
123
124
125
126
127
*03H
2
3
4
5
….
122
123
124
125
126
127
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
….
….
….
….
58
58
58
58
59
59
59
59
60
60
60
60
61
61
61
61
62
62
62
62
63
63
63
63
0
1
< FIFO for WAVE >
0
1
WAVE_CH#1
0
1
WAVE_CH#2
0
1
0
1
5-3. D/A AND EARPHONE OUTPUT
QS6400 provides switchable audio out mode beteen DAC and EARPHONE.
Using the output-mode register you can select whether audio output is DAC or Earphone.
When using earphone out, the DAC interface is in accessible, because the DAC and
Earphone out pin actually use the same hardware pin.
Earphone Right
enable or disable
Mono
or
"REG_OUT_MODE BIT5"
Stereo
enable or disable
Earphone Left
P38 :*WCLK
or Earphone_right
Sel
P39 :*SCLK
or Earphone_left
"REG_OUT_MODE BIT4"
D/AC Interface
"REG_OUT_MODE BIT6"
enable or disable
P5 :Sout
23/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
5-4. STEREO PWM OUTPUT
QS6400 supports two kinds of speaker out mode, DAC out or PWM out.
In using PWM mode, you should select whether it is Stereo or Mono.
PWM Right
enable or disable
P36 :PWM R(+)
P_CHN
N_CHN
Mono
or
"REG_OUT_MODE BIT7"
P33 :PWM R(-)
Stereo
enable or disable
PWM Left
P35 :PWM L(+)
P_CHN
N_CHN
Sel
P32 :PWM L(-)
"REG_OUT_MODE BIT4"
MUTE
"REG_OUT_MODE BIT6"
Chapter 6 Appplication Flow Chart
[ QS6400 Initialize ]
1) Reset or Wake Up from Power Down Mode
2) Read Register : Value = REG_QDSP_MODE
3) Value == 0x83
4) Write Register : REG_READY_QS = 0x4D
5) Initialize Registers
Write Register : REG_WAVE_CHAN = 0x00
Write Register : REG_OUT_MODE = 0x00
Write Register : REG_PWM_CLOCK = 0x01
Etc.
[Note] If “0x83” is not detected on step 3) for over 300mSec, regard as hardware
failure in QS6400.
24/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
[ QS6400 MIDI File Play Flow ]
1) Initialize Process
2) Command Out : REG_SMF_CTRL = 0x11
3) Set Register Index : REG_SMF_BUF
CNT = 0;
4) Write 1 Byte Data
CNT = CNT + 1;
5) CNT == 128
6) Write Register : REG_SMF_EOP = 0x05
7) IRQB == 0
8) Read Register : Value = REG_IREQ_TYPE
9) Value.5 == 1
10) Value.2 == 1
END
25/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
[ QS6400 WAVE File Play Flow ]
1) Initialize Process
2) Set Wave Channel : REG_WAVE_CHAN =
0x01
Set Sampling Rate : REG_WAV1_SR
3) Command Out : REG_WAV1_CTRL = 0x11
4) Set Register Index : REG_WAV1_BUF
CNT = 0;
5) Write 1 Byte Data
CNT = CNT + 1;
6) CNT == 128
7) IRQB == 0
8) Read Register : Value = REG_IREQ_TYPE
9) End of Wave Data?
10) Value.1 == 1
11) Command Our : REG_WAV1_CTRL = 0x12
26/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
Chapter 7 Eletrical Charateristics and soldering temperature
Absolute maximum range
Item
PVDD terminal power supply voltage
VDD terminal power supply voltage
EVDD terminal power supply voltage
Digital input voltage
Operating ambient temperature
Carrier temperature
Symbol
PVDD
VDD
EVDD
VIND
TOP
TCA
Min
-0.5
-0.5
-5
VSS-0.5
-20
-50
Max
4.5
4.0
4.0
VDD+0.5
85
125
Min
2.7
2.5
2.5
-20
Typ
3
3
3
25
Max
4.2
3.6
3.6
85
Recommended operating condition
Item
Symbol
PVDD operating voltage
PVDD
EVDD operating voltage
EVDD
VDD operating voltage
VDD
TOP
Operating ambient temperature
DC characteristics
Item
Input voltage "H" level
Input voltage "L" level
Output voltage "H" level, IOH = -4m
Output voltage "L" level, IOL = 4m
Earphone VOH , IOH = -16mA
Earphone VOL , IOL = 16mA
PWM VOH , IOH = -100mA
PWM VOH , IOL = 100mA
Input leakage current
Input capacity
AC characteristics
MRSTB,XIN
Item
MRTSB active "L" pulse width
XIN frequecy
XIN rising / falling time
XIN duty
Note : VDD = 3.3V , VSS = 0V
Min
Typ
Max
0.7*VDD
0.3*VDD
2.4
0.4
2.4
0.4
2.4
0.4
-1
1
10
Symbol
VIH
VIL
VOH
VOL
VEOH
VEOL
VPOH
VPOL
IL
CI
Symbol
TRSTW
1/TFREQ
TR/TF
TH/TFREQ
Min
512
2
30
Unit
V
V
V
V
deg. C
deg. C
Unit
V
V
deg. C
Unit
V
V
V
V
V
V
V
V
uA
pF
Note : VDD = 3V±0.3 ,Copacitor load = 50pF
Typ
Max
Unit
*xin
26
Mhz
30
ns
50
70
%
TRSTW
VIH
MSRTB
VIL
TH
TF
VIH
VIL
XIN
TR
TFREQ
27/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
CSB, WRB, RDB, A0, IREQB, D0~D7
Item
Symbol
CSB active "L" pulse width(write)
TCSW
Address setup time
TAS
WRB active "L" pulse width
TWW
Data setup time
TWDS
Data hold time
TWDH
CSB active "L" pulse width(read)
TCSR
Address setup time
TRAS
RDB active "L" pulse width
TRW
Data read access time
TACC
Data hold time
TRDH
IREQB active "L" pulse width
TREQW
QS6400
When XIN = 20Mhz
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
70
ns
50
ns
us
Min
120
10
100
30
5
120
10
100
10
1.6
A0
TCSW
TCSW
CSB
TAS
TWW
TAS
TWW
WRB
TWDS
TWDS
TWDH
D0~D7
Invalid
Index Valid
TWDH
Invalid
Data Valid
Timing of Write Operation
A0
TCSW
TCSR
CSB
TAS
TWW
WRB
TRAS
TRW
RDB
TWDS
TWDH
D0~D7
Invalid
Index Valid
Invalid
TACC
TRDH
Data Valid
Timing of Read Operation
28/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
BCLK
WCLK
MSB
LSB
MSB
LSB
SDATA
BCLK,WCLK,SDATA
When XIN = 20Mhz
Item
Symbol
Min
Typ
Max
Unit
BCLK 1/Freq time
TBLK
820
ns
WCLK 1/Freq time
TWLK
26
us
SDATA 1/Freq time
TWW
100
ns
Power consumption
Min
Item
VDD section ( without speaker )
Typ
Max
20
Unit
mA
Power consumption 8Ω load and 360mW out
200
mA
Power down mode
10
uA
TOP =-20~85°C
Note : PVDD=VDD = 3.3V
Soldering temperature
Item
Soldering temperature
Min
Typ
Max
-5
235
5
Unit
℃
29/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
Chapter 8 SMF Sound Table
1) GM LITE SOUND TABLE
PC#
1
2
3
Piano
4
5
ChPercu
ssion
Organ
Guita
r
Bass
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
CCO
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tone name
Acoustic Grand Piano
Daegum
Brigh Acoustic Piano
Taepyoungso
Electric Grand Piano
Haegum
Honkey tonk Piano
Gayagum
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Celesta
Glockenspiel
Music Box
Vibraphone
Marinba
Xylophone
Tubular Bells
Dulcimer
Drawbar Organ
Percussive Organ
Rock Organ
Church Organ
Reed Organ
Accordion
Harmonica
Tango Accordion
Acoustic Guitar (nylon)
Acoustic Guitar (steel)
Electric Guitar (jazz)
Electric Guitar (clean)
Electric Guitar (muted)
Overdriven Guitar
Distortion Guitar
Guitar harmonics
Acoustic Bass
Electric Bass (finger)
Electric Bass (pick)
Bass
String
/
Orche
stra
Emsemble
Brass
Reed
Pipe
PC#
CCO
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tone name
Fretless Bass
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Violin
Viola
Cello
Contrabass
Tremolo Stings
Pizzicato Strings
Orchestral Harp
Timpani
String Ensemble 1
String Ensemble 2
SynthStrings 1
SynthStrings 2
Choir Aashs
Voice Oohs
Synth Voice
Orchestra Hit
Trumpet
Trombone
Tuba
Muted Trumpet
French Hom
Brass Section
SynthBrass 1
SynthBrass 2
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Hom
Bassoon
Clarinet
Piccolo
Flute
Recorder
continude next page
30/37
HWA SOUND SOURCE
PC#
76
77
Pipe
78
79
80
81
82
83
Synth 84
lead
85
86
87
88
89
90
91
Synth 92
pad
93
94
95
96
97
98
99
Synth 100
SFX 101
102
103
104
105
106
107
Ethni 108
c
109
110
111
112
113
Percu
114
ssive
115
CCO
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Advanced ADPCM SOUND DSP for Mobile
Tone name
PC#
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Lead 1 (square)
Lead 2 (sawtooth)
Lead 3 (calliope)
Lead 4 (chiff)
Lead 5 (charang)
Lead 6 (voice)
Lead 7(fifths)
Lead 8(bass + lead)
Pad 1 (new age)
Pad 2 (warm)
Pad 3 (polysynth)
Pad 4 (choir)
Pad 5 (bowed)
Pad 6 (metallic)
Pad 7 (halo)
Pad 8 (sweep)
FX 1 (rain)
FX 2 (soundtrack)
FX3 (crystal)
FX 4 (atmosphere)
FX 5 (brightness)
FX 6 (goblins)
FX7 (echoes)
FX 8 (sci-fi)
Sitar
Banjo
Shamisen
Koto
Kalimba
Bag pipe
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
116
117
Percu
118
ssive
119
120
121
122
123
124
SFX
125
126
127
128
CCO
0
0
0
0
0
0
0
0
0
0
0
0
0
QS6400
Tone name
Woodblock
Taiko Drum
Melodic Tom
Synth Drum
Reverse Cymbol
Guitar Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
PC# :
CC0 :
31/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
2) Percussion Map( Channel 10 PC#1 )
Note
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
PC#1:STANDARD Set
Kick Drum 2/Jazz BD2
Kick Drum 1/Jazz BD1
Side Stick
Snare Drum 1
Hand Clap
Snare Drum 2
Low Tom 2
Closed Hi-hat
[EXC1]
Low Tom 1
Pedai Hi-hat
[EXC1]
Mid Tom 2
Open Hi-hat
[EXC1]
Mid Tom 1
High Tom 2
Cymbal 1
High Tom 1
Ride Cymbal 1
Chinese Cymbal
Ride Bell
Tambourine
Splash Cymbal
Cowbell
Crash Cymbal 2
Vibra - slap
Ride Cymbal 2
High Bongo
Low Bongo
Mute High Conga
Open High Conga
Low Conga
High Timbale
Low Conga
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
High Agogo
Low Agogo
Cabasa
Maracas
Short Hi Whistle [EXC2]
Long Low Whistle [EXC2]
Short Guiro
[EXC3]
Long Guiro
[EXC3]
Claves
High Wood Block
Low Wood Block
Mute Cuica
[EXC4]
Open Cuica
[EXC4]
Mute Triangle
[EXC5]
Open Triangle
[EXC5]
-
32/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
Percussion Map( Channel 10 PC#2 )
Note
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
PC#2:HWASS Set
Muted Ggangary
Ggangary
Jing
Muted Jing
Jangu
Muted Jangu
BUK
Muted Jangu
Kick Drum 2/Jazz BD2
Kick Drum 1/Jazz BD1
Side Stick
Snare Drum 1
Hand Clap
Snare Drum 2
Low Tom 2
Closed Hi-hat
[EXC1]
Low Tom 1
Pedai Hi-hat
[EXC1]
Mid Tom 2
Open Hi-hat
[EXC1]
Mid Tom 1
High Tom 2
Cymbal 1
High Tom 1
Ride Cymbal 1
Chinese Cymbal
Ride Bell
Tambourine
Splash Cymbal
Cowbell
Crash Cymbal 2
Vibra - slap
Ride Cymbal 2
High Bongo
Low Bongo
Mute High Conga
Open High Conga
Low Conga
High Timbale
Low Conga
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
High Agogo
Low Agogo
Cabasa
Maracas
Short Hi Whistle [EXC2]
Long Low Whistle [EXC2]
Short Guiro
[EXC3]
Long Guiro
[EXC3]
Claves
High Wood Block
Low Wood Block
Mute Cuica
[EXC4]
Open Cuica
[EXC4]
Mute Triangle
[EXC5]
Open Triangle
[EXC5]
ed Ggangary
Ggangary
Jing
uted Jing
Jangu
ted Jangu
BUK
ted Jangu
33/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
MIDI Implementation Chart
Recognized
Function
Transmitted
Remarks
default
X
1~16
Channel
Changed
X
1~16 Each
Mode
Default
X
Mode 1*
X
21 ~108
Basic
Note number
Velocity
ON
X
O
Velocity
OFF
X
O
After Touch
Key's
X
X
After Touch
Chn's
X
X
X
O
0,32
X
O
Bank Selection
1
X
O
Modulation
6,38
X
O
Data entry(100,101 Only)
Pitch Bender
Control Change
Program
System
Common
7
X
O
Volume
10
X
O
Panpot
11
X
O
Expression
64
X
O
Sustain
66
X
X
Soft
67
X
X
Sustanuto
100,101
X
O
RPN LSB MSB(00,00 Only)
120
X
O
All sound off
121
X
O
Reset all controller
123
X
O
All note off
Change
X
0-127
Exclusive
X
X
Song position
X
X
Song selection
X
X
Tune
X
X
Mode 1* : Omni ON / Poly ON
34/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
Chapter 9 Outline Dimensions
35/37
HWA SOUND SOURCE
Advanced ADPCM SOUND DSP for Mobile
QS6400
Chapter 10 Marking
- Part_number =QS6400
- Datecode = Year/Numbers of week
ex) Production day = 2003/1/07
QS6400
"0302"
36/37
History of Revision.
Date
03-03-31
Change of Contents
-
Revision Number
Ver 1.0
03-09-01
Revision the "Chapter 5-1 Register Table"
-
04-03-30
Added the "Chapter 5-1 Register Table and Detail"
Ver 2.0
37/37