HMC397


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC397
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC397
v03.0109
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
2
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Typical Applications
Features
An excellent cascadable 50 Ohm
Gain Block or LO Driver for:
Gain: 15 dB
• Microwave & VSAT Radios
Stable Gain Over Temperature
• Test Equipment
50 Ohm I/O’s
• Military EW, ECM, C3I
Small Size: 0.38 x 0.58 x 0.1 mm
P1dB Output Power: +15 dBm
• Space Telecom
Functional Diagram
General Description
The HMC397 die is a GaAs InGaP Heterojunction
Bipolar Transistor (HBT) Gain Block MMIC DC to
10 GHz amplifier. This amplifier can be used as either
a cascadable 50 Ohm gain stage or to drive the
LO of HMC mixers with up to +16 dBm output power.
The HMC397 offers 15 dB of gain and an output
IP3 of +32 dBm while requiring only 56 mA from a
+5V supply. The Darlington feedback pair used results in reduced sensitivity to normal process
variations and yields excellent gain stability over
temperature while requiring a minimal number of
external bias components. The HMC397 can easily
be integrated into Multi-Chip-Modules (MCMs) due
to its small (0.22mm2) size. All data is with the chip
in a 50 Ohm test fixture connected via 0.025mm
(1 mil) diameter wire bonds of minimal length 0.5mm
(20 mils).
Electrical Specifi cations, Vs= +5 V, Rbias= 22 Ohm, TA = +25° C
Parameter
Min.
Typ.
Max.
Gain
15
14
12
dB
dB
dB
Gain Variation Over Temperature
DC - 3.0 GHz
3.0 - 7.0 GHz
7.0 - 10.0 GHz
0.004
0.015
0.02
dB/ °C
dB/ °C
dB/ °C
Input Return Loss
DC - 3.0 GHz
3.0 - 10.0 GHz
15
14
dB
dB
Output Return Loss
DC - 3.0 GHz
3.0 - 10.0 GHz
15
13
dB
dB
Reverse Isolation
DC - 7.0 GHz
7.0 - 10.0 GHz
18
16
dB
dB
Output Power for 1 dB Compression (P1dB)
DC - 3.0 GHz
3.0 - 7.0 GHz
7.0 - 10.0 GHz
15
13
10
dBm
dBm
dBm
Output Third Order Intercept (IP3)
DC - 3.0 GHz
3.0 - 7.0 GHz
7.0 - 10.0 GHz
30
24
22
dBm
dBm
dBm
Noise Figure
DC - 7.0 GHz
7.0 - 10.0 GHz
4.5
6
dB
dB
56
mA
Supply Current (Icq)
Note: Data taken with broadband bias tee on device output.
2 - 14
Units
DC - 3.0 GHz
3.0 - 7.0 GHz
7.0 - 10.0 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC397
v03.0109
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Gain & Return Loss
Gain vs. Temperature
2
20
20
10
5
S21
S11
0
S22
-5
-10
14
+25 C
+85 C
-55 C
11
8
-15
5
-20
0
1
2
3
4
5
6
7
8
9
0
10
2
4
Input Return Loss vs. Temperature
8
10
Output Return Loss vs. Temperature
0
0
+25 C
+85 C
-55 C
-5
RETURN LOSS (dB)
RETURN LOSS (dB)
6
FREQUENCY (GHz)
FREQUENCY (GHz)
-10
-15
-20
+25 C
+85 C
-55 C
-5
-10
-15
-20
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
FREQUENCY (GHz)
4
5
6
7
8
9
10
9
10
FREQUENCY (GHz)
Noise Figure vs. Temperature
Reverse Isolation vs. Temperature
0
10
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
17
GAIN (dB)
RESPONSE (dB)
15
8
NOISE FIGURE (dB)
REVERSE ISOLATION (dB)
9
-5
+25 C
+85 C
-55 C
-10
-15
-20
+25 C
+85 C
-55 C
7
6
5
4
3
2
1
-25
0
0
1
2
3
4
5
6
FREQUENCY (GHz)
7
8
9
10
1
2
3
4
5
6
7
8
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 15
HMC397
v03.0109
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Output P1dB vs. Temperature
16
16
Psat (dBm)
P1dB (dBm)
20
12
8
+25 C
+85 C
-55 C
4
+25 C
+85 C
-55 C
8
0
0
2
4
6
8
10
0
2
FREQUENCY (GHz)
Power Compression @ 1 GHz
6
8
10
Power Compression @ 7 GHz
20
Pout (dBm), GAIN (dB), PAE (%)
20
15
10
5
0
Pout
Gain
PAE
-5
-10
-20
-16
-12
-8
-4
0
4
15
10
5
0
Pout
Gain
PAE
-5
-10
-20 -18 -16 -14 -12 -10 -8
8
INPUT POWER (dBm)
+25 C
+85 C
-55 C
14
10
2
4
6
FREQUENCY (GHz)
-2
0
2
4
6
8
10
80
40
35
60
30
25
40
20
15
10
5
Gain
P1dB
Psat
IP3
Icq
0
0
4.5
20
4.75
5
5.25
Vs(V)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5.5
Icq (mA)
22
GAIN (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
26
0
-4
Gain, Power, Output IP3 & Supply
Current vs. Supply Voltage @ 1 GHz
34
18
-6
INPUT POWER (dBm)
Output IP3 vs. Temperature
IP3 (dBm)
4
FREQUENCY (GHz)
30
2 - 16
12
4
0
Pout (dBm), GAIN (dB), PAE (%)
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
2
Psat vs. Temperature
20
HMC397
v03.0109
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Absolute Maximum Ratings
+7 Vdc
RF Input Power (RFIN)(Vcc = +5 Vdc)
+10 dBm
Junction Temperature
150 °C
Continuous Pdiss (T= 85 °C)
(derate 5.21 mW/°C above 85 °C)
0.339 W
Thermal Resistance
(junction to die bottom)
192 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
2
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. ALL DIMENSIONS IN INCHES [MILLIMETERS]
2. DIE THICKNESS IS 0.004 (0.100) BACKSIDE IS GROUND
3. BOND PADS ARE 0.004 (0.100) SQUARE
4. BACKSIDE METALLIZATION: GOLD
5. BOND PAD METALLIZATION: GOLD
Die Packaging Information [1]
Standard
Alternate
GP-3 (Gel Pack)
[2]
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
Collector Bias Voltage (Vcc)
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 17
HMC397
v03.0109
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Pad Descriptions
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
2
Pad Number
Function
Description
Interface Schematic
1
RFIN
This pin is DC coupled.
An off chip DC blocking capacitor is required.
2
RFOUT
RF output and DC Bias for the output stage.
Die
Bottom
GND
Die bottom must be connected to RF/DC ground.
Application Circuit
Note:
1. Select Rbias to achieve Icq using equation below,
Rbias > 22 Ohm.
2. External blocking capacitors are required on
RFIN and RFOUT.
Icq = Vs - 3.9
Rbias
Recommended Component Values
Frequency (MHz)
Component
50
2 - 18
1000
3000
7000
L1
270 nH
56 nH
8.2 nH
2.2 nH
C1, C2
0.01 μF
100 pF
100 pF
100 pF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC397
v03.0109
InGaP HBT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Assembly Diagram
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag
for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
DRIVER & GAIN BLOCK AMPLIFIERS - CHIP
2
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The
mounting surface should be clean and fl at.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 19