DTA150A-H SERIES 140~150 Watts, Desktop AC/DC Power Supplies Rev D FEATURES • Class I • Single Outputs Available Ranging from 12V to 52V • RoHS Compliant • No Load Power Consumption < 150mW • Power Factor > 0.95 @ 115VAC • Over Voltage, Over Load, and Short Circuit • 90~264 VAC Input Voltage Range • 89% High Efficiency Protection • Meets CEC, ERP, EISA Efficiency Level VI • AC Inlet: IEC-320-C14 Inlet • 100% Burn-in and Hi-pot Tested • 140~150 Watts Output Power Requirements • UL60950-1, CSA C22.2-No.60950-1, TUV EN60950-1, CB IEC60950-1 Safety Approvals DESCRIPTION Size: 6.69 x 3.35 x 1.73 inches (780g) 170.0 x 85.0 x 44.0 mm Weight: 1.72 lbs The DTA150A-H series of Class I AC/DC desktop power supplies provides up to 150 Watts output power in a 6.69 x 3.35 x 1.73 inch package. This series consists of single output models ranging from 12VDC to 48VDC with a 90~264VAC input voltage range and an IEC320-C14 AC inlet connector. These supplies also feature no load power consumption <150mW, power factor > 0.95 at 115VAC, and 89% typical efficiency. These supplies are protected against short circuit, over voltage, and over load conditions and have UL60950-1, CSA C22.2-No.60950-1, TUV EN60950-1, and CB IEC60950-1 safety approvals. All models are CEC/Energy Star Level VI compliant. This series has been 100% burn-in and hi-pot tested. MODEL SELECTION TABLE Model Number Input Voltage Range Output Voltage (1) Output Current Min Max Output Power Ripple & Noise (2) Output Regulation DTA-140A-1Y120H 12 VDC 0A 11.67A 140W 240mVp-p ±5% DTA-150A-1Y160H 16 VDC 0A 9.38A 150W 320mVp-p ±5% 19 VDC 0A 7.90A 150W 380mVp-p ±5% DTA-150A-1Y240H 24 VDC 0A 6.25A 150W 480mVp-p ±3% DTA-150A-1Y360H 36 VDC 0A 4.17A 150W 480mVp-p ±3% DTA-150A-1Y480H 48 VDC 0A 3.13A 150W 480mVp-p ±3% DTA-150A-1Y190H 90 - 264 VAC 07/09/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797 website: www.wallindustries.com • e-mail: [email protected] Page 1 of 4 Rev D DTA150A-H SERIES 140~150 Watts, Desktop AC/DC Power Supplies TECHNICAL SPECIFICATIONS: DTA150A-H SERIES All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS INPUT SPECIFICATIONS Input Voltage Range Input Frequency Input Current (rms) Inrush Current Min 90 47 90VAC and full load 264VAC and full load 115VAC, cold start, 25°C 230VAC, cold start, 25°C No Load Power Consumption Power Factor Correction 115VAC and full load 230VAC and full load Typ Max Unit 264 63 2.5 1.25 75 150 500 VAC Hz A Apeak mW 0.95 0.90 OUTPUT SPECIFICATIONS Output Voltage Output Regulation See Table See Table Output Power Output Current Minimum Load See Table See Table 0 Ripple & Noise (20MHz BW) Hold-up Time PROTECTION Over Voltage Protection Over Load Protection Short Circuit Protection GENERAL SPECIFICATIONS Efficiency Measured at 20MHz limited bandwidth and with a 10µF electrolytic capacitor and a 0.1µF ceramic capacitor in parallel across the output 115VAC and full load @Average Load, 115VAC/230VAC For 4 seconds Isolation Resistance 500VDC Primary to Secondary Primary to Frame Ground Primary to Secondary Primary to Frame Ground ENVIRONMENTAL SPECIFICATIONS Operating Ambient Temperature Derating linearly 2.5% per °C from 41°C to +60°C Storage Temperature Range Humidity MTBF Full load and 25°C ambient temperature PHYSICAL SPECIFICATIONS AC Inlet Output Connector 12VDC ~ 24VDC output models Output Cable (Standard) 36VDC ~ 48VDC output models Weight Dimensions (L x W x H) SAFETY & EMC Safety Approvals EMC Standards See Table 16 ms Shutdown and latch-off, AC recycle Automatic Recovery Automatic Recovery automatic recovery Dielectric Withstand Voltage % 89 4242 2121 20 20 0 -10 10 140,000 % VDC MΩ +60 +85 90 °C °C % hours IEC-320-C14 Several options available See mechanical drawing See mechanical drawing 1.72 lbs (780g) 6.69 x 3.35 x 1.73 inch (170.0 x 85.0 x 44.0 mm) UL60950-1, CSA C22.2-No.60950-1, TUV EN60950-1, CB IEC60950-1 FCC Class B, CISPR22 Class B, EN55022 Class B, CE NOTES 1. Other output voltages are available: 140W for 12~24VDC, 150W for 15~26VDC, 33~39VDC, and 44~52VDC. Please call factory for ordering details. 2. Ripple & noise is measured at 20MHz limited bandwidth and with a 10µF electrolytic capacitor and a 0.1µF ceramic capacitor in parallel across the output. 3. Several output connectors available; please call factory for ordering details. 07/09/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797 website: www.wallindustries.com • e-mail: [email protected] Page 2 of 4 Rev D DTA150A-H SERIES 140~150 Watts, Desktop AC/DC Power Supplies DERATING CURVE MECHANICAL DRAWING Notes: 1. 2. 3. 4. AC Inlet: IEC320-C14 Plastic Case Color: Black Tolerance: ±0.5mm Unit=mm Standard Output Cable 1. 2. 3. AWM 1571 #14 AWG/ 1C + SHIELDING, UL 80ºC 30V VW-1, 1050 mm. (12-24V) AWM 1185 #16 AWG/ 1C + SHIELDING, UL 80ºC 300V VW-1, 1050 mm. (36-48V) Depends on Customers Requirements 07/09/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797 website: www.wallindustries.com • e-mail: [email protected] Page 3 of 4 Rev D DTA150A-H SERIES 140~150 Watts, Desktop AC/DC Power Supplies COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 07/09/2014 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 37 Industrial Drive Exeter, NH 03833 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797 website: www.wallindustries.com • e-mail: [email protected] Page 4 of 4