Cree® XLamp® XB-G High‑Voltage White LEDs PRODUCT DESCRIPTION FEATURES Table of Contents Built on Cree’s SC³ Technology® Platform, • Binned @ 85 °C & 44 mA Characteristics........................................ 2 XB-G High‑Voltage White • Available in 80-minimum CRI Flux Characteristics................................ 2 (HVW) LED is optimized to lower cost for • 200 mA maximum drive current Relative Spectral Power Distribution..... 3 high-lumen, omnidirectional replacement • 22.5 V typical forward voltage Electrical Characteristics........................ 3 @ 85 °C, 44 mA Relative Flux vs. Current......................... 4 the XLamp ® lamps. The XB-G HVW LED delivers high efficacy in the small XB footprint and • Wide viewing angle: 140° Typical Spatial Distribution..................... 4 enables smaller and more efficient driver • Reflow solderable - JEDEC Thermal Design....................................... 5 J-STD‑020C compatible Reflow Soldering Characteristics........... 6 Unlimited floor life at Notes....................................................... 7 ≤ 30 °C/85% RH Mechanical Dimensions......................... 8 • Electrically neutral thermal path Tape and Reel.......................................... 9 • RoHS‑compliant Packaging.............................................. 10 • UL® recognized component circuits than standard-voltage LEDs. In addition, the XB-G LED has a wider • light distribution that can improve the omnidirectionality of ENERGY STAR replacement lamps. ® www.cree.com/Xlamp (E349212) Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 CLD-DS72 Rev 2C Product family data sheet XLamp ® XB-G HVW LED Characteristics Characteristics Unit Thermal resistance, junction to solder point °C/W 5.5 degrees 140 mV/°C -16 Viewing angle (FWHM) Temperature coefficient of voltage Minimum ESD classification (HBM per Mil-Std-883D) Typical Maximum Class 2 DC forward current mA 200 Reverse voltage V -0.1 Forward voltage (@ 44 mA, 85 °C) V LED junction temperature °C 22.5 25 150 Flux Characteristics (TJ = 85 °C) The following table provides several base order codes for XLamp XB-G HVW LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XB LED Family Binning and Labeling document. Minimum Luminous Flux @ 44 mA CCT Range Color Minimum 80 CRI Minimum 2700 K Maximum 3000 K Calculated Minimum Luminous Flux (lm)** Order Code Group Flux (lm) @ 85 °C Flux (lm) @ 25 °C* 66 mA 100 mA Q5 107 120 153 216 XBGHVW-H0-0000-00000HDE7 Q4 100 112 143 202 XBGHVW-H0-0000-00000HCF8 Q3 93.9 105 134 190 XBGHVW-H0-0000-00000HBE8 Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 7). • Minimum CRI for 80 CRI Minimum is 80. * Flux values @ 25 °C are calculated and are for reference only. ** Calculated flux values at 66 mA and 100 mA are for 85 °C and are for reference only. Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 2 XLamp ® XB-G HVW LED Relative Spectral Power - XB-G tall dome Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 60 2700 K - 3600 K CCT 40 20 0 380 430 480 530 580 630 680 730 780 23.5 24.0 24.5 25.0 Wavelength (nm) Electrical Characteristics (TJ = 85 °C) Electrical Characteristics (Tj = 85ºC) - XB-G tall dome 200 175 Forward Current (mA) 150 125 100 75 50 25 0 21.0 21.5 22.0 22.5 23.0 Forward Voltage (V) Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 3 XLamp ® XB-G HVW LED Relative Intensity vs. Current (Tj = 85ºC) - XB-G tall dome Relative Flux vs. Current (TJ = 85 °C) 350 Relative Luminous Flux (%) 300 250 200 150 100 50 0 0 25 50 75 100 125 150 175 200 Forward Current (mA) Typical Spatial Radiation Pattern - XB-G tall dome Typical Spatial Distribution Relative Luminous Intensity (%) 100 80 60 40 20 -90 -70 -50 -30 -10 0 10 30 50 70 90 Angle (º) Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 4 XLamp ® XB-G HVW LED Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end Thermal Design product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and talloptical dome characteristics. 250 Maximum Current (mA) 200 150 100 Rj-a = 10°C/W Rj-a = 15°C/W 50 Rj-a = 20°C/W Rj-a = 25°C/W 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (ºC) Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 5 XLamp ® XB-G HVW LED Reflow Soldering Characteristics In testing, Cree has found XLamp XB-G HVW LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak IPC/JEDEC J-STD-020C Time Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) 65-150 seconds 217 °C 45-90 seconds 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 6 XLamp ® XB-G HVW LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XB-G HVW LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. UL® Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. Vision Advisory WARNING: Do not look at exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 7 XLamp ® XB-G HVW LED 6 6 5 5 4 4 OTICE NOTICE AL. NFIDENTIAL. THIS PLOTTHIS ANDPLOT THE INFORMATION AND THE INFORMATION NED N ARE WITHIN THE PROPRIETARY ARE THE PROPRIETARY AND AND ENTIAL ORMATION INFORMATION OF CREE, INC. OF CREE, THIS PLOT INC. THIS PLOT ED, T BE REPRODUCED COPIED, REPRODUCED OR DISCLOSED OR DISCLOSED TO ANY TO ANY ERSON ORIZEDWITHOUT PERSON THE WRITTEN WITHOUT THE CONSENT WRITTEN CONSENT 6 5 INC. Thermal vias, if present, 6areNOTICE not shown on these drawings. 5 CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT ANDOF THE INFORMATION CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY MAY NOT BE COPIED, REPRODUCED ORAND DISCLOSED TO ANY CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT UNAUTHORIZED PERSONOF WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, OF CREE INC. REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. 3 2 Mechanical Dimensions 4 4 2 REVISONS REV B C D LENS IN PLACE B PUT LARGERPUT LARGER LENS IN PLACE ADJUSTED C ADJUSTED HEIGHT 3 HEIGHT D ADJUSTED HEIGHT 3ADJUSTED HEIGHT R DESCRIPTION DESCRIPTION 0.82 0.46 0.82 REV B C D 1.14 1.14 ANODE 2.2 ±0.1 mm REVISONS REV All measurements are ±.13 mm unless otherwise indicated. 2.2 ±0.1 mm D B C D 0.46 D 1.14 2.2 0.82 2.2 ±0.1 mm ±0.1 mm 2.45 2.45 90° 90° 0.94 0.94 90° 2.45 90° 2.45 0.2 0.36 0.2 2.45 2.45 C 0.73 0.73 0.33 0.33 0.94 0.36 0.94 0.92 0.92 C Top View 0.36 0.82 0.43 0.82 0.46 0.43 0.43 0.85 0.85 0.43 0.36 0.43 0.43 0.82 0.43 0.82 0.46 0.46 0.28 B 2.34 B 2.27 0.28 1.17 2.34 0.36 0.36 0.36 2.34 2.34 0.28 0.28 0.92 0.92 0.36 A 6 1.14 2.27 1.14 2.27 DATE DRAWN BY DRAWN BYDATE UNLESS OTHERWISE UNLESS OTHERWISE SPECIFIED SPECIFIED D. CRONIN 05/14/13 DIMENSIONSDIMENSIONS ARE IN D. CRONIN ARE IN 05/14/13 CHECK CHECK DATE DATE MILLIMETERS MILLIMETERS AND AFTER FINISH. AND AFTER FINISH. TOLERANCE TOLERANCE UNLESS SPECIFIED: UNLESS SPECIFIED: .XX ± .25 .XX ± APPROVED .25 DATE DATE APPROVED TITLE TITLE .XXX ± .125.XXX ± .125 2.27 0.28 X° ± .5° X° ± .5° THIRD ANGLE THIRD PROJECTION ANGLE PROJECTION XBE/XBG OUTLIN XBE UNLESS OTHERWIS MATERIAL 2.27 FOR SHEET METAL FOR SHEET PARTS METAL ONLYPARTSMATERIAL ONLY DIMENSIONS AR D ± 1.5 .X ± 1.5 UNLESS OTHERWISE SPEC MILLIMETERS AND RECOMMENDED.XSTENCIL PATTERN DRAWING D NA SIZE SIZE .XX ± .75 .XX ± .75 DIMENSIONS ARE IN TOLERANCE UNLES .XXX ± .25 .XXX ± .25 FINAL PROTECTIVE FINAL PROTECTIVE FINISH FINISH 2610-00 MILLIMETERS AND FC RECOMMENDED STENCIL PATTERN C CAFTER .XX ± .25 X° ± .5° X° ± .5° TOLERANCE UNLESS .XXX ±SPEC .12 SCALE 1.6 1.6 .XX ±SCALE SURFACE FINISH: SURFACE FINISH: 31.000 31.000 X°.25 ± .5°A Recommended Stencil Pattern THIRD ANGLE PROJECTION .XXX .125 FOR±±SHEET 3 3 2 2 X° .5° METAL THIRD ANGLE PROJECTION .X ±PARTS 1.5M FOR SHEET METAL .XX ± .75 .X ± .XXX 1.5 ± .25 .XX ± X°.75 ± .5° .XXX ± .25 1.6F X°SURFACE ± .5° FINISH: 1.6 4 3 SURFACE FINISH: 0.28 RECOMMENDED STENCIL PATTERN RECOMMENDED STENCIL PATTERN 0.280.28 0.36 2.34 2.34 RECOMMENDED PCB SOLDER PAD Recommended PCB Solder 5 RECOMMENDED 5 4 PCB SOLDER PAD Pad 6 6 2.27 1.17 1.17 0.28 2.27 0.28 2.34 0.28 0.28 0.36 0.28 RECOMMENDED PCB SOLDERPCB PADSOLDER RECOMMENDED PAD 0.36 0.36 A 1.14 0.28 0.36 0.92 2.27 2.34 1.14 1.17 0.92 0.2 0.85 0.46 0.36 0.36 0.2 Bottom 0.73View 0.73 0.85 0.43 0.36 Side View 2.45 2.45 0.28 6 3 4 5 5 4 3 Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 8 6 DETAIL B SCALE 2 : 1 5 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 3 2 1 REVISONS REV DESCRIPTION BY Released DC 10/23/11 JL ADDED CATHODE AND ANODE NOTE DC 2/26/12 A B DATE APP'D DC HVW LED XLamp XB-G ® CHANGED POCKET DIMS AND TOLERANCES C 8/3/12 D D Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. All dimensions in mm Tolerance unless specified: .xx ± .25, .xxx ± .125, x° ± C.5° 1.50 +.10/-.00 C 1.75 ±.10 4.00 ±.10 CATHODE SIDE 2.00 ±.10 B B 2.60+/-0.1mm 4° 1.5±.1 4.0±.1 8.0±.1 1.75±.10 12.00 Nominal 12.30 Max 10.25 ±.10 Cathode Side ANODE SIDE .30 ± .10 8.00 ±.10 B 2.5±.1 B 5.50 ±.10 1.00 ± .10 +.3 12.0 .0 Anode Side SECTION B-B (denoted by + and circle) 2.05 +/-0.1 2.60 +/-0.1 REFERENCE VENDOR PART NUMBER 020246 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° DATE DRAWN BY User Feed Direction A END THIRD ANGLE PROJECTION Notes: 1. 10 sprocket hole pitch cumulative tolerance ± 0.2mm FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° D. CRONIN DATE APPROVED DATE 5 Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) 4 Loaded Pockets (1,000 Lamps) Phone (919) 313-5300 START TITLE SIZE FINAL PROTECTIVE FINISH SCALE 3 Fax (919) 313-5558 A Carrier Tape, 2525 HEW MATERIAL SURFACE FINISH: 1.6 6 4600 Silicon Drive Durham, N.C 27703 10/23/11 CHECK C REV. DRAWING NO. 4.000 2 2402-00020 SHEET C OF 1 /1 1 Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction Cover Tape Pocket Tape 13mm 7" Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 9 XLamp ® XB-G HVW LED Packaging Unpackaged Reel Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Code, Quantity, Reel ID Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Packaged Reel Patent Label Label with Customer Order Label with Cree Order Code, Code, Qty, Reel ID, PO # Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Patent Label (on bottom of box) Copyright © 2013-2015 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp®, EasyWhite® and SC³ Technology® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. 10