CLD-DS44 rev 7D Product family data sheet Cree® XLamp® XM-L HVW LEDs Product Description FEATURES Table of contents The Cree XLamp® XM-L High‑Voltage • Binned at 85 °C Characteristics....................................... 2 White • Typical forward voltage of 46 V @ Flux Characteristics............................... 2 44 mA, with Vf binning available Relative Spectral Power Distribution.... 3 (HVW) LED provides the lighting‑class performance and reliability of Cree XLamp LEDs in the standard • Cree-standard XM mechanical Relative Flux vs. Junction XM package. The XM-L HVW LED is an footprint, with electrically neutral Temperature........................................... 3 order of magnitude smaller than other thermal path Electrical Characteristics....................... 4 high-voltage LED arrays, allowing easy • Low thermal resistance: 3.5 °C/W Relative Flux vs. Current........................ 4 implementation • Wide viewing angle: 110° Typical Spatial Distribution.................... 5 lighting applications with smaller, more • Maximum drive current: 125 mA Thermal Design...................................... 5 efficient high-voltage drivers. Among • Maximum junction temperature: Reflow Soldering Characteristics.......... 6 of space-constrained these applications are lamps such as A19, B10, GU10, MR16, PAR30 and E17. 150 °C Notes...................................................... 7 • Unlimited floor life at ≤ 30 ºC/85% RH Mechanical Dimensions........................ 8 • Reflow solderable Tape and Reel......................................... 9 • Available in standard CRI and Packaging............................................. 10 80‑minimum CRI configurations • RoHS-compliant www.cree.com/Xlamp • UL® recognized component (E349212) Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® XM-L HVW LED Characteristics Characteristics Unit Thermal Resistance, junction to solder point °C/W 3.5 degrees 110 mV/°C -35 Viewing Angle (FWHM) Temperature coefficient of voltage Minimum ESD Classification (HBM per Mil-Std-883D) Typical Maximum Class 2 DC Forward Current mA 125 Reverse Current mA 0.1 Forward voltage (@ 44 mA, 85 °C) V LED Junction Temperature °C 46 55 150 Flux Characteristics (TJ = 85 °C) The following table provides several base order codes for XLamp XM-L HVW LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XM-L LED Binning and Labeling document. CCT Range Color Cool White Neutral White Warm White Minimum 5000 K 3700 K 2600 K Maximum 8300 K 5000 K 3700 K Minimum Luminous Flux @ 44 mA Order Code Group Flux (lm) @ 85 °C Flux (lm) @ 25 °C* T3 220 255 XMLHVW-Q0-0000-0000LT351 T4 240 278 XMLHVW-Q0-0000-0000LT451 T5 260 301 XMLHVW-Q0-0000-0000LT551 T2 200 231 XMLHVW-Q0-0000-0000LT2E5 T3 220 255 XMLHVW-Q0-0000-0000LT3E5 T4 240 278 XMLHVW-Q0-0000-0000LT4E5 S6 182 211 XMLHVW-Q0-0000-0000LS6E7 T2 200 231 XMLHVW-Q0-0000-0000LT2E7 T3 220 255 XMLHVW-Q0-0000-0000LT3E7 Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 7). • Typical CRI for Cool White (5000 K – 8300 K CCT) is 68. • Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75. • Typical CRI for Warm White (2600 K – 3700 K CCT) is 82. * Flux values at 25 °C are calculated and for reference only. Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 2 XLamp ® XM-L HVW LED Relative Spectral Power Relative Spectral Power Distribution 100% Relative Radiant Power 80% 60% 5000 K - 8300 K CCT 2600 K - 3700 K CCT 40% 20% 0% 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 44 mA) 120% Relative Luminous Flux 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 3 XLamp ® XM-L HVW LED Electrical Characteristics (TJ = 85 °C) Electrical Characteristics (Tj = 85ºC) 140 Forward Current (mA) 120 100 80 60 40 20 0 40 42 44 46 48 50 52 Forward Voltage (V) Relative Intensity vs. Current (Tj = 85ºC) Relative Flux vs. Current (TJ = 85 °C) Relative Luminous Flux 250% 200% 150% 100% 50% 0% 0 25 50 75 100 125 Forward Current (mA) Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 4 XLamp ® XM-L HVW LED Typical Spatial Radiation Pattern Typical Spatial Distribution 100% Relative Luminous Intensity 80% 60% 40% 20% -90 -70 -50 -30 -10 0% 10 30 50 70 90 Angle (º) Thermal Design Thermal Design 140 Maximum Current (mA) 120 100 80 60 Rj-a = 10 °C/W 40 Rj-a = 15 °C/W Rj-a = 20 °C/W 20 Rj-a = 25 °C/W 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (ºC) Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 5 XLamp ® XM-L HVW LED Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L HVW LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow-soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak Time Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) 65-150 seconds 217 °C 45-90 seconds 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 6 XLamp ® XM-L HVW LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XM-L HVW LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. UL® Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 7 XLamp ® XM-L HVW LED Mechanical Dimensions 6 6 5 Thermal vias, ifNOTICE present, are not shownNOTICE on these drawings. 5 4 4 3 CREE CONFIDENTIAL. THIS PLOT AND THECONFIDENTIAL. INFORMATION THIS PLOT AND THE INFORMATION CREE CONTAINED WITHIN ARE THE PROPRIETARY ANDWITHIN ARE THE PROPRIETARY AND CONTAINED CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED MAY OR DISCLOSED TO ANY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. OF CREE INC. D D 5.00 5.00 REV C 2 1 REVISONS DESCRIPTION REV All measurements are ±.13 mm unlessADDED otherwise B DOME RADIUSindicated. B C 3.095 ±0.2 mm 3.095 ±0.2 mm .50 0.73 5.00 3 2 CHANGED SOLDERPAD AND STENCIL C 4.78 4.78 3.78 3.78 2.78 BY DATE DES DC 10/23/12 ADDED DOM DC 06/16/1 CHANGED SOLDE 2.78 .50 0.73 .50 .50 4.78 5.00 4.7 C R 2.26 R 2.26 Side View Top View Bottom View .25 .50 B .50 .50 .80.50 .25 .80 .50 .80 B 4.78 4.78 4.78 A .50 4.78 2.78 2.78 4.78 4.78 .25 .25 .97 4.78 A RECOMMENDED PCB SOLDER PAD .80 RECOMMENDED STENCIL PATTERN RECOMMENDED PCB SOLDER PAD (HATCHED AREA IS OPENING) Recommended PCB Solder Pad .97 ALL DIMENSIONS ± ARE .13MM UNLESS ALL OTHERWISE NOTED DIMENSIONS ± ARE DRAWN BY DATE DRAWN BY D UNLESS OTHERWISE SPECIFIED UNLESS OTHERWISE SPECIFIED D. CRONIN 08/1/11 D. CRONIN460 DIMENSIONS ARE IN DIMENSIONS ARE IN Dur CHECK DATE CHECK Pho D MILLIMETERS AND AFTER FINISH. MILLIMETERS AND AFTER FINISH. RECOMMENDED STENCIL PATTERN -TOLERANCE UNLESS SPECIFIED: -TOLERANCE UNLESS SPECIFIED: -Fax .XX ± .25 (HATCHED AREA IS OPENING) APPROVEDDATE .XX ± .25 APPROVEDD TITLE .XXX ± .125 .XXX ± .125 ---X° ± .5° X° ± .5° THIRD ANGLE PROJECTION OUTLINE DRAWING, 5050 XML HV THIRD ANGLE PROJECTION MATERIAL MATERIAL FOR SHEET METAL PARTS ONLY Recommended Stencil Pattern (Hatched Area is Open) .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5° 1.6 SURFACE FINISH: 6 6 5 5 4 .13MM UNLESS OTHERWIS 4.78 4 3 -- FOR SHEET METAL PARTS ONLY 1.5 .75DRAWING NO. -2610-00018 .25 FINAL PROTEC X° ± .5° SCALE 1.6 SH 16.000 SURFACE FINISH: -- 3 2 2 1 .X ± SIZE -.XX ± FINAL PROTECTIVE FINISH.XXX C ± Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 8 6 5 4 3 2.00[.079] 4.00[.157] 1 2 REVISIONS NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. DESCRIPTION REV BY DATE APP'D POCKET SIZE Do1.50 P2 +.10 +.0039 .0591 -.00 -.0000 [ ] 1.75[.069] E1 Po Ao - 5.40mm [.213"] Bo - 5.40mm [.213"] Ko - 3.35mm [.132"] 3.0° Tape and Reel 5.50[.217]F 6 12.00[.472] NOMINAL 6 5 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THETHIS PROPRIETARY ANDINFORMATION CREE CONFIDENTIAL. PLOT AND THE CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN AREOF THE PROPRIETARY AND MAY NOT BE COPIED, INFORMATION REPRODUCEDOF ORCREE, DISCLOSED TO PLOT ANY CONFIDENTIAL INC. THIS UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT D XLamp ® XM-L HVW LED 5.40[.213] Bo 4 5 3 4 10.25 All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. OF CREE INC. D D 12.30 [.484] MAX W [.404] E2 2.00[.079] 2.00[.079] P2 1.50[.059] 4.00[.157] D1 4.00[.157] Po 8.00[.315] P +.10 +.0039 Do1.50 .0591 +.0039 -.00 +.10 .0591 -.0000 [] Do1.50 -.00 -.0000 [ ] P2 REV REV 6 C 5 4 C NOTICE TIAL. THIS PLOT AND THE INFORMATION HIN ARE THE PROPRIETARY AND NFORMATION OF CREE, INC. THIS PLOT PIED, REPRODUCED OR DISCLOSED TO ANY PERSON WITHOUTTHE WRITTEN CONSENT 3.0° Ao THIRD ANGLE PROJECTION B REV A UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 X° ± .5 ° SURFACE FINISH: 5 END 8 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) D D. CRONIN A 5.40[.213] 5.40[.213] Bo Bo 3.0° C Loaded Pockets (1000 Lamps) 6 BY DATE DDS 11/8/10 DC 2/26/12 1.50[.059] Phone (919) 313-5300 Fax (919) 313-5558 D1 1.50[.059] D1 DATE 8.00[.315] DATE 8.00[.315] P TITLE P APPROVED BS SIZE FINAL PROTECTIVE FINISH 63 REV. DRAWING NO. A 2402-00011 7.0° SCALE DRAWING SCALE 2 A SHEET 7.0° OF 1 4 3.35[.132] 1.75 3.35[.132] Ko 3 Ko START B 3.35 2 1 2400-00009 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 INDEX QTY ITEM COMMENTS DATE DRAWN BY UNLESS OTHERWISE SPECIFIED 1 1D. CRONIN 2400-00009-CORE C DATE DRAWN BY 4/23/10 UNLESS ARE OTHERWISE SPECIFIED DIMENSIONS IN INCHES CRONIN 4/23/10 2 CHECK 2 D.2400-00009-REEL DATE DIMENSIONS ARE IN INCHES AND AFTER FINISH. CHECK DATE AND AFTERSPECIFIED: FINISH. TOLERANCE UNLESS TOLERANCE .XX ± UNLESS .01 SPECIFIED: APPROVED DATE TITLE ± .01 .XXX .XX ± .005 APPROVED DATE TITLE X° ±.XXX .5± ° .005 THIRD ANGLE PROJECTION MATERIAL X° PARTS ± .5 ° FOR SHEET METAL ONLY THIRD ANGLE PROJECTION MATERIAL FOR.XSHEET METAL PARTS ONLY ± .06 Leader DRAWING NO. SIZE .XX .X ± ±.03 .06 DRAWING NO. SIZE 400mm (min.) of FINAL PROTECTIVE FINISH ± .03 .XXX .XX ± .010 FINAL PROTECTIVE FINISH X° ±.XXX .5± ° .010 empty pockets with SCALE X° ± .5 ° SURFACE FINISH: 63 at least 100mm DRAWINGSCALE SCALE SURFACE FINISH: 63 DRAWING SCALE 12 Ao 4600 Silicon Drive Durham, N.C 27703 4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Phone (919) 313-5300 Fax (919) 313-5558 Fax (919) 313-5558 A XMXM 5050 CARRIER TAPE 5050 CARRIER TAPE 2402-00011 A 2402-00011 A D (40 5sealed by tape empty5 pockets min.) 4 REV. REV. 3 4 2 3 SHEET OF 1OF / 1 SHEET 1 2 1 A 1 /1 B 12.4 +.2 .0 MEASURED AT HUB C C 330 +.25 -.75 16.4 +0.2 .0 MEASURED AT HUB THIRD ANGLE PROJECTION 6 B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 5 4 1.6 3 1.9±.4 DATE DRAWN BY D. CRONIN CHECK 21 ±.4 4600 Silicon Drive Durham, N.C 27703 06/08/10 DATE -- Phone (919) 313-5300 -- Fax (919) 313-5558 A DATE APPROVED -- TITLE 13.1 ±.2 -- MATERIAL -- SIZE FINAL PROTECTIVE FINISH -- SCALE XM LOADING SPEC REV. DRAWING NO. C 2402-00012 SHEET 3.000 2 B OF B 1 /1 1 12.4 +1.0 -.5 MEASURED AT EDGE 60° 60° REVISONS REV A UNLESS OTHERWISE SPECIFIED BY DESCRIPTION DRAWN BY DATE APP'D DATE 4600 Silicon Drive D. CRONIN 09/29/09 DIMENSIONS ARE®INare INCHES Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp registered trademarks and the Cree logo is a trademark Durham, N.C 27703 of AND AFTER FINISH. Phone (919) 313-5300 Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. TOLERANCE UNLESS SPECIFIED: --Fax (919) 313-5558 CHECK THIRD ANGLE PROJECTION B 1 /1 A 6 C APP'D .36[.014] D T .36[.014] T A XM 5050 CARRIER TAPE MATERIAL 5.40[.213] 5.40[.213] Ao ANODE SIDE D 4600 Silicon Drive Durham, N.C 27703 4/23/10 CHECK CATHODE SIDE 4 5 A D DATE DRAWN BY User 3 Feed Direction 4 6 APP'D DATE APP'D 1 10.25 12.30 [.484] 12.30 DESCRIPTION MAX[.484] [.404]10.25 [.404] pocket count Loaded was 750 W MAX E2 WNOTE LARGER E2 AND ANODE MADE CATHODE B CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 B DATE BoBo - - 5.40mm [.213"] 5.40mm [.213"] KoKo - - 3.35mm [.132"] 3.35mm [.132"] 12.00[.472] 12.00[.472] NOMINAL NOMINAL 2 1 BY REVISONS 3.35[.132] Ko 5.40[.213] 6 5.50[.217]F 5.50[.217]F 3 BY POCKET SIZE POCKET SIZE Except as noted, all dimensions in mm. AoAo - - 5.40mm [.213"] 5.40mm [.213"] B 7.0° 1 2 REVISIONS REVISIONS DESCRIPTION DESCRIPTION 1.75[.069] E1 1.75[.069] E1 .36[.014] T Po 2 3 C .XX ± .XXX ± X° ± .01 .005 .5 ° FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 DATE APPROVED -- DATE -- MATERIAL ANTI-STATIC HIPS FINAL PROTECTIVE FINISH 9 REEL, 13" X 12MM, 3 PIECE SNAP TITLE SIZE C DRAWING NO. 2400-00009 REV. A A A XLamp ® XM-L HVW LED Humidity Indicator Card (inside bag) Packaging Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright © 2011-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 10