VTM™ Current Multiplier VTM48MP010T135AA0 Sine Amplitude Converter™ (SAC™) Features Product Ratings • 48 Vdc to 1 Vdc 135 A current multiplier ■■Operating from standard 48 V or 24 V PRM™ regulators ■■Up to 60 Volts DC input VIN = 0 to 60 V IOUT = 135 A (nom) VOUT = 0 to 1.25 V (no load) K = 1/48 Product Description ■■K of 1/48 provides up to 135 A DC output current • High efficiency (>94%) reduces system power consumption • High density (1948 A/in3) • Vicor’s 1323 ChiP package enables low impedance interconnect to system board • Provides enable / disable control, internal temperature monitoring, internal current monitoring The Vicor’s 1323 ChiP VTM current multiplier is a high efficiency (>94%) Sine Amplitude Converter™ (SAC™) operating from a 0 to 60 Vdc primary bus to deliver a 0 to 1.25 Vdc low voltage output. The Sine Amplitude Converter offers a low AC impedance beyond the bandwidth of most downstream regulators; therefore capacitance normally at the load can be located at the input to the Sine Amplitude Converter. Since the K factor of the VTM48MP010T135AA0 is 1/48, the capacitance value can be reduced by a factor of 2304, resulting in savings of board area, materials and total system cost. The VTM48MP010T135AA0 is provided in Vicor’s 1323 ChiP package compatible with standard pick-and-place assembly processes. The co-molded ChiP package provides enhanced thermal management due to a large thermal interface area and superior thermal conductivity. The high conversion efficiency of the VTM48MP010T135AA0 increases overall system efficiency and lowers operating costs compared to conventional approaches. • ZVS / ZCS resonant Sine Amplitude Converter topology • Parallel up to 10 modules Typical Applications The VTM48MP010T135AA0 enables the utilization of Factorized Power Architecture™ which provides efficiency and size benefits by lowering conversion and distribution losses and promoting high density point of load conversion. • Computing and Telecom Systems ■■Optimized for the Intel VR12.5 Processor Specification • Automated Test Equipment • High Density Power Supplies • Communications Systems vicorpower.com 800 927.9474 VTM48MP010T135AA0 Pin Configuration TOP VIEW 1 2 +OUT A A +OUT -OUT B B -OUT +OUT C C +OUT -OUT D D -OUT +OUT E E +OUT -OUT F F EN G G TM VCC H H CM +IN I I -OUT -IN 1323 device Pin Numbering and Descriptions Pin Number Signal Name Type A1, A2 C1, C2 E1, E2 +OUT OUTPUT POWER Positive output terminal B1, B2 D1, D2 F1, F2 -OUT OUTPUT POWER RETURN Negative output terminal G1 EN INPUT To disable VTM in system G2 TM OUTPUT H1 VCC INPUT H2 CM OUTPUT Current monitor I1 +IN INPUT POWER Positive input terminal I2 -IN INPUT POWER RETURN Negative input terminal Function Temperature monitor and Power Good Flag Power train controller supply vicorpower.com 800 927.9474 VTM48MP010T135AA0 Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor’s product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Vicor’s Standard Terms and Conditions All sales are subject to Vicor’s Standard Terms and Conditions of Sale, which are available on Vicor’s webpage or upon request. Product Warranty In Vicor’s standard terms and conditions of sale, Vicor warrants that its products are free from non-conformity to its Standard Specifications (the “Express Limited Warranty”). This warranty is extended only to the original Buyer for the period expiring two (2) years after the date of shipment and is not transferable. UNLESS OTHERWISE EXPRESSLY STATED IN A WRITTEN SALES AGREEMENT SIGNED BY A DULY AUTHORIZED VICOR SIGNATORY, VICOR DISCLAIMS ALL REPRESENTATIONS, LIABILITIES, AND WARRANTIES OF ANY KIND (WHETHER ARISING BY IMPLICATION OR BY OPERATION OF LAW) WITH RESPECT TO THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT, OR ANY OTHER MATTER. This warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, or storage. Vicor shall not be liable for collateral or consequential damage. Vicor disclaims any and all liability arising out of the application or use of any product or circuit and assumes no liability for applications assistance or buyer product design. Buyers are responsible for their products and applications using Vicor products and components. Prior to using or distributing any products that include Vicor components, buyers should provide adequate design, testing and operating safeguards. Vicor will repair or replace defective products in accordance with its own best judgment. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty. Life Support Policy VICOR’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor’s Intellectual Property Department. The products described on this data sheet are protected by the following U.S. Patents Numbers: 5,945,130; 6,403,009; 6,710,257; 6,911,848; 6,930,893; 6,934,166; 6,940,013; 6,969,909; 7,038,917; 7,145,186; 7,166,898; 7,187,263; Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 email Customer Service: [email protected] Technical Support: [email protected] vicorpower.com 800 927.9474