Issue Date:
2010-02-12
Page 1 of 6
Report Reference #
E135493-A10-UL
2014-07-17
UL TEST REPORT AND PROCEDURE
Standard:
Certification Type:
CCN:
Product:
Model:
UL 60950-1, 2nd Edition, 2011-12-19 (Information Technology
Equipment - Safety - Part 1: General Requirements)
CSA C22.2 No. 60950-1-07, 2nd Edition, 2011-12 (Information
Technology Equipment - Safety - Part 1: General Requirements)
Component Recognition
QQGQ2, QQGQ8 (Power Supplies for Information Technology
Equipment Including Electrical Business Equipment)
DC/DC Converter
Half PRM Model ViP01wwxHy
Half PRM2 Model PRMbbbcdddefffxzz
See Enclosure Miscellaneous for model suffix details.
Input:45Vdc (38-55)
Output: 48 Vdc
Power: 250W Max.
Rating:
Applicant Name and Address:
VICOR CORP
25 FRONTAGE RD
ANDOVER MA 01810-5499
UNITED STATES
This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the
above referenced Standards. The products have been found to comply with the requirements covering the category and the products are
judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on
such products which comply with this Test Report and any other applicable requirements of UL LLC ('UL') in accordance with the FollowUp Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up
Service under the indicated Test Procedure.
The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.
UL authorizes the applicant to reproduce the latest pages of the referenced Test Report consisting of the first page of the Specific
Technical Criteria through to the end of the Conditions of Acceptability.
Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL.
Prepared by:
Gerard Soprych
Reviewed by: Daniel Pirozzi
Copyright © 2014
Issue Date:
2010-02-12
Page 2 of 6
Report Reference #
E135493-A10-UL
2014-07-17
Supporting Documentation
The following documents located at the beginning of this Procedure supplement the requirements of this Test
Report:
A. Authorization - The Authorization page may include additional Factory Identification Code markings.
B. Generic Inspection Instructions i. Part AC details important information which may be applicable to products covered by this Procedure.
Products described in this Test Report must comply with any applicable items listed unless otherwise
stated in the body of this Test Report.
ii. Part AE details any requirements which may be applicable to all products covered by this Procedure.
Products described in this Test Report must comply with any applicable items listed unless otherwise
stated in the body of each Test Report.
iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical
standard used to investigate these products. Products are permitted to bear only the Certification
Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report.
Product Description
The half size VI Chip PRM is a non-isolating DC-DC front end Pre-Regulator Module that is designed to be
used with a VI Chip VTM to make a complete regulated DC-DC converter. The PRM DC-DC converters are
designed for building-in and the input is intended to be derived from a TNV-2, SELV, or other non-hazardous
secondary circuit.
Model Differences
See Miscellaneous Enclosure for model nomenclature.
Issue Date:
2010-02-12
Page 3 of 6
Report Reference #
E135493-A10-UL
2014-07-17
Technical Considerations
Equipment mobility : for building-in
Connection to the mains : N/A
Operating condition : continuous
Access location : N/A
Over voltage category (OVC) : OVC II
Mains supply tolerance (%) or absolute mains supply values : N/A
Tested for IT power systems : No
IT testing, phase-phase voltage (V) : -
Class of equipment : Class III (supplied by SELV)
Considered current rating of protective device as part of the building installation (A) : 10
Pollution degree (PD) : PD 2
IP protection class : IP X0
Altitude of operation (m) : 5000
Altitude of test laboratory (m) : less than 2000
Mass of equipment (kg) : 0.0065
The product was submitted and evaluated for use at the maximum ambient temperature (Tma)
permitted by the manufacturer’s specification of: max. case temperature of 100°C
Engineering Conditions of Acceptability
For use only in or with complete equipment where the acceptability of the combination is determined by UL
LLC. When installed in an end-product, consideration must be given to the following:
Max Temperature: Keep the maximum case temperature of the VI Chip at 100°C or less.
The Half PRM is a non-isolating device. The output can be considered SELV if the input is SELV with
the exception of the VIZ0050. The output of the VIZ0050 can exceed the SELV limits under a fault
condition but does not exceed the limits of TNV-2 circuits..
Fusing requirements: The Half PRM Series of DC-DC converters were evaluated with Littelfuse
Nano² Fuse rated 10A.
The output of the VIZ0050 may be considered TNV-2 or external circuitry may be added and
evaluated in the end product in order to provide output over voltage protection and compliance with
the limits of SELV circuits.
The following secondary output circuits are SELV: 48Vdc
The power supply terminals and/or connectors are: Not investigated for field wiring
The investigated Pollution Degree is: 2
The following end-product enclosures are required: Fire , Mechanical
The following secondary output circuits are at non-hazardous energy levels: outputs greater than
240W
Issue Date:
2010-02-12
Page 4 of 6
Report Reference #
2014-07-17
VI Chip Half PRM Family Tree Model: ViP01wwxHy
Example #1, VIP0101THJ
V = Constant
i=
I
M
PRM Type
Standard PRM
Military PRM
P01 = Constant
ww = defines electrical ratings
Model
Vin Nom (range)
00
45 Vdc (38-55)
01
45 Vdc (38-55)
02
45 Vdc (38-55)
x=
T
M
Product Grade
Telecom
Military
Vout
0-55 Vdc
0-55 Vdc
0-55 Vdc
Pout
200 W
200 W
200 W
Feedback Style
Remote Sense
Remote Sense
Adaptive Loop
Temp Range
-40 - 100 C
-55 - 100 C
H = Constant for Half VIC Package Size
y=
J
T
Lead Designator
J-Lead
Through-Hole
Customer Special Model numbers
Customer Special
Model Numbers
VIZ0050, VIZ0050x (see license conditions)
x = revision, any letter A through Z, non-safety related
Equivalent Standard
Model Numbers
VIP0101THJ
E135493-A10-UL
Issue Date:
2010-02-12
Page 5 of 6
Report Reference #
2014-07-17
VI Chip Half PRM2 Family Tree Model: PRMbbbcdddefffxzz
Example: PRM48BH480T200A00
PRM = Constant
PRM Family (Pre-regulator Module)
PRM Standard version
MPRM Mil-COTS version
bbb = 48B
Input Voltage
48A
48B
48D
48J
Nominal (range)
48 Vdc (36-75)
48 Vdc (38-55)
48 Vdc (38-60)
48 Vdc (42-55)
c= H
Package Size and lead designator
Half VI Chip J-Lead
H
ddd = 480
Output Voltage Designator (range)
48.0 Vdc (5-55)
480
e= T
Product Grade
T
M
-40 to 125C
-55 to 125C
fff = 200
Output Power Designator (can be any three digits from 100 to 250) non-inclusive
list of examples below
100W
100
200W
200
250W
250
x= A
Revision (non-safety related)
Any alphanumeric character
x
zz = 00
Customer reference (non-safety related)
Any alphanumeric character
zz
E135493-A10-UL
Issue Date:
2010-02-12
Page 6 of 6
Report Reference #
2014-07-17
Half Size Customer Configured PRM2 Model Number: PRMxyaa-zzzzzz
Example: PRM2A03-123456
PRM = Constant
PRM Family (Pre-regulator Module)
x=2
Controller Revision, 0 through 9 (non-safety related)
y=A
Product Revision, A through Z (non-safety related)
aa = 03
Hardware Configuration, max ratings, actual ratings may be less
HW Configuration
Vin (Vdc)
Vout (Vdc)
03 = full size narrow range
48Vdc (38-55)
48 Vdc (20-55)
04 = full size wide range
48Vdc (36-75)
48 Vdc (20-55)
Pout (W)
250W
200W
zzzzzz = 123456
Any 6 digit numeric combination, customer specific configuration, non-safety related, J-Lead
or Through-Hole, T or M grade, and Feedback Style
E135493-A10-UL