SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - SMA Pb e3 RoHS Description SIDACtor® SMA Series are designed to protect baseband equipment such as phones, faxes, modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards. Features and Benefits • Low voltage overshoot • Low on-state voltage Agency Approvals Agency • Fails short circuit when surged in excess of ratings • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133080 • Low capacitance • 2nd level interconnect is Pb-free per IPC/ JEDEC J-STD-609A.01 Applicable Global Standards Schematic Symbol Additional Information • TIA-968-A* • IEC 61000-4-5* • TIA-968-B* • YD/T 1082 • ITU K.20/21 Enhanced Level* • YD/T 993 • YD/T 950 • ITU K.20/21 Basic Level • GR 1089 Inter-building* Datasheet • GR 1089 Intra-building * Line impedance required to pass operationally Samples Resources Electrical Characteristics Part Number Marking P0080S1ALRP P0220S1ALRP P0300S1ALRP P1800S1ALRP P2300S1ALRP P2600S1ALRP P3100S1ALRP P3500S1ALRP P0080S1BLRP P0220S1BLRP P0300S1BLRP P1800S1BLRP P2300S1BLRP P2600S1BLRP P3100S1BLRP P3500S1BLRP P-8A P22A P03A P18A P23A P26A P31A P35A P-8B P22B P03B P18B P23B P26B P31B P35A VDRM @lDRM=5µA VS @100V/µs IH IS IT V min V max mA min mA max A max 6 15 25 170 190 220 275 320 6 15 25 170 190 220 275 320 25 32 40 220 260 300 350 400 25 32 40 220 260 300 350 400 50 50 50 150 150 150 150 150 50 50 50 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps Capacitance @1MHz, 2V bias V max pF min pF max 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 25 10 10 10 10 10 10 10 20 10 10 10 10 10 10 10 35 30 30 30 30 30 30 30 35 30 30 30 30 30 30 30 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/15 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Series Surge Ratings IPP 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 ITSM 50/60 Hz di/dt A min A min A min A min A min A min A min A min A min A min Amps/µs max A 20 150 150 90 50 75 75 50 75 20 500 B - 250 250 90 60 75 75 55 75 25 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W DO-214AC V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 8 6 25 °C 4 2 IH (TC = 25ºC) IH 10 Ratio of Percent of VS Change – % 2.0 14 12 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/15 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/15 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Marking Part Numbering P xxx 0 S1 x L RP Pxxx xxxxx REEL PACK TYPE P = SIDACtor RoHS COMPLIANT MEDIAN VOLTAGE CONSTRUCTION VARIABLE Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP RATING A = A rating B = B rating PACKAGE TYPE Dimensions DO-214AC (SMA) Dimensions C A B H D F E G J K L I Inches Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.177 3.990 4.500 Package Type S1 0.100 0.110 2.540 2.790 0.078 0.090 1.980 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.194 0.208 4.930 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Description Packing Options Quantity Added Suffix Industry Standard DO-214AC Tape & Reel Pack 12mm/13” tape 5000 RP EIA-481 0.157 (4.0) 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/15 Dimensions are in inches (and millimeters). Direction of Feed Max C (all dimensions in mm) Tape and Reel Specification — DO-214AC Min D Solder Pads Packing Options Millimeters