TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SP1026 Series SP1026 Series 15pF 30kV Bidirectional Discrete TVS RoHS Pb GREEN Description Zener diodes fabricated in a proprietary silicon avalanche technology protect each I/O pin to provide a high level of protection for electronic equipment that may experience destructive electrostatic discharges (ESD). These robust diodes can safely absorb repetitive ESD strikes at ±30kV (contact discharge, IEC 61000-4-2) without performance degradation. Additionally, each diode can safely dissipate 5A of 8/20µs surge current (IEC61000-4-5) with very low clamping voltages. Features Pinout Pin 1 Pin 2 • ESD, IEC61000-4-2, ±30kV contact, ±30kV air • Low leakage current of 0.5µA (MAX) at 5V • EFT, IEC61000-4-4, 40A (5/50ns) • Space efficient 0201 footprint) • Lightning, IEC61000-4-5 2nd edition, 5A (8/20µs) • Halogen free, Lead free and RoHS compliant Applications Functional Block Diagram • Mobile phones 1 • Smart phones • Portable navigation devices • Smart watches • Portable medical devices • Tablets Application Example Keypads I/O Controller P1 2 P2 Outside World P3 IC P4 Case GND SP1026 (x4) Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. ©2015 Littelfuse, Inc. ©2016 Specifications are subject to change without notice. Revision: 03/09/16 SP1007 Series TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SP1026 Series Absolute Maximum Ratings Symbol Parameter Value Units 5 A Operating Temperature -40 to 125 °C Storage Temperature -55 to 150 °C IPP Peak Pulse Current (tp=8/20μs) TOP TSTOR CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Thermal Information Parameter Rating Units -55 to 150 °C Maximum Junction Temperature 150 °C Maximum Lead Temperature (Soldering 30s) 260 °C Storage Temperature Range Electrical Characteristics (TOP=25ºC) Parameter Symbol Reverse Standoff Voltage VRWM Test Conditions Min Typ Max Units 6.0 V 0.5 μA Breakdown Voltage VBR IR=1mA (Pin 1 to 2) 7.8 Leakage Current ILEAK VR=5V 0.1 Ipp=1A, tp=8/20µs (Pin 1 to 2) 12.0 V Ipp=2A, tp=8/20µs (Pin 1 to 2) 13.4 V Clamp Voltage1 VC Dynamic Resistance RDYN ESD Withstand Voltage1 Diode Capacitance1 VESD (VC2 - VC1) / (IPP2 - IPP1) V 1.4 Ω IEC61000-4-2 (Contact Discharge) ±30 kV IEC61000-4-2 (Air Discharge) ±30 kV CD Reverse Bias=0V 15 pF Reverse Bias=2.5V 12 pF Note: 1 Parameter is guaranteed by design and/or device characterization. Capacitance vs. Reverse Bias Insertion Loss (S21) I/O to GND 0 Attenuation (dB) Capacitance (pF) 20 15 10 5 0 -10 -15 -20 -25 -30 0 0.5 1 1.5 2 2.5 3 3.5 Bias Voltage (V) ©2015 Littelfuse, Inc. ©2016 Specifications are subject to change without notice. Revision: 03/09/16 -5 4 4.5 5 10 100 1000 Frequency (MHz) SP1007 Series TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SP1026 Series Clamping Voltage vs. IPP Transmission Line Pulsing(TLP) Plot 20 20 16 15 14 TLP Current (A) Clamp Voltage (VC) 18 12 10 8 10 6 5 4 2 0 0 1 2 3 4 5 0 5 10 15 20 25 TLP Voltage (V) Peak Pulse Current-IPP (A) 8/20μS Pulse Waveform 110% 100% 90% Percent of IPP 80% 70% 60% 50% 40% 30% 20% 10% 0% 0.0 5.0 10.0 15.0 20.0 25.0 30.0 Time (μs) Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/09/16 tP TP Temperature Reflow Condition Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-do Ramp-down Preheat TS(min) 25 tS time to peak temperature Time SP1007 Series TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SP1026 Series Product Characteristics Lead Plating Matte Tin or Pre-Plated Frame Lead Material Copper Alloy Lead Coplanarity 0.004 inches(0.102mm) Substrate material Silicon Body Material Molded Epoxy Flammability UL 94 V-0 Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. Package Dimensions — μDFN-2 (0201) Package μDFN-2 (0201) JEDEC Symbol TOP VIEW SIDE VIEW 0.32 Pin2 Pin1 0.14 BOTTOM VIEW 0.24 0.32 Inches Min Max Min Max A 0.23 0.33 0.009 0.013 A1 0.00 0.05 0.000 0.002 A2 0.24 MO-236 Millimeters 0.10 REF 0.004 REF b 0.18 0.30 0.007 0.012 D 0.55 0.65 0.022 0.026 E 0.25 0.35 0.010 0.014 L1 0.12 0.24 0.005 0.009 L2 0.12 0.23 0.005 0.009 K1 0.165 REF 0.006 REF SOLDERING PATTERN Part Numbering System Ordering Information SP 1026 – 01 U T G TVS Diode Arrays (SPA® Diodes) Series Number of Channels G= Green Part Number Package Marking Min. Order Qty. SP1026-01UTG μDFN-2 I I 15000 T= Tape & Reel Package U: μDFN-2 Part Marking System ©2015 Littelfuse, Inc. ©2016 Specifications are subject to change without notice. Revision: 03/09/16 SP1007 Series TVS Diode Arrays (SPA®® Diodes) General Purpose ESD Protection - SP1026 Series Embossed Carrier Tape & Reel Specification — μDFN-2 P0 P1 P2 D0 Symbol E F W 0.20 ± 0.05 T 0º MAX A0 K0 ©2015 Littelfuse, Inc. ©2016 Specifications are subject to change without notice. Revision: 03/09/16 0º MAX B0 Millimetres Inches Min Max Min Max A0 0.33 0.40 0.013 0.016 B0 0.63 0.70 0.025 0.028 D0 1.40 1.60 0.055 0.063 E 1.65 1.85 0.065 0.073 F 3.45 3.55 0.136 0.140 K0 0.30 0.39 0.012 0.015 P0 1.90 2.10 0.075 0.083 P1 1.95 2.05 0.077 0.081 P2 3.90 4.10 0.154 0.161 T 0.13 0.25 0.005 0.010 W 7.90 8.30 0.311 0.327 SP1007 Series