TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- SP4042 Series SP4042 Series 3.3V Diode Array RoHS Pb GREEN Description The SP4042 integrates low capacitance steering diodes with a TVS diode to provide 2 channels of protection against lightning induced surge events and ESD. This robust device can safely absorb up to 120A per IEC610004-5 (tP= 2/10μs) without performance degradation and a minimum ±30kV ESD per IEC61000-4-2 international standard. The low loading capacitance makes the SP4042 ideal for protecting Ethernet interfaces. Pinout Features 1 2 3 4 5 GND • ESD, IEC61000-4-2, ±30kV contact, ±30kV air • Low capacitance of 11pF (TYP) per line • L ightning, IEC610004-5 2nd edition, 120A (tP=2/10μs) • Low leakage current of 0.1μA (MAX) at 3.3V • E FT, IEC61000-4-4, 40A (tP=5/50ns) 10 9 8 7 6 Functional Block Diagram Applications • 10/100/1000 Ethernet Interfaces • Customer Premise Equipment (CPE) Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/29/16 • L ead-free and RoHS compliant • Carrier Class Equipment • PBX Systems TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- SP4042 Series Thermal Information Absolute Maximum Ratings Symbol Parameter Value Parameter Units Rating Units -55 to 150 °C Peak Current (tp=8/20μs) 95 A IPP Peak Current (tp=2/10μs) 120 A Maximum Junction Temperature 150 °C PPK Peak Pulse Power (tp=2/10µs) 2500 W Maximum Lead Temperature (Soldering 20-40s) 260 °C TOP Operating Temperature -40 to 85 ºC TSTOR Storage Temperature -55 to 150 °C SP4061 IPP Storage Temperature Range CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions VRWM IR≤1μA, Line to Line Reverse Breakdown Voltage VBR IT=1mA, Line to Line 3.5 V Snap Back Voltage VSB ISB=50mA 2.8 V ILEAK VR=3.3V, Line to Line Reverse Standoff Voltage Reverse Leakage Current Clamp Voltage, Line to GND Clamp Voltage, Line to Line VC ESD Withstand Voltage1 IPP=100A, tp=2/10µs VESD Dynamic Resistance, Line to GND Dynamic Resistance, Line to Line Typ IPP=100A, tp=2/10µs 1 1 Min Diode Capacitance1 Units 3.3 V 0.1 µA 17 22 V 22 25 V IEC61000-4-2 (Contact) ±30 kV IEC61000-4-2 (Air) ±30 kV 2 2 Max 0.05 Ω 0.15 Ω RDYN TLP, tp=100ns CI/O-GND Line to GND, VR=0V, f=1MHz 11 25 pF CI/O-I/O Line to Line, VR=0V, f=1MHz 5.5 12 pF Note: 1 Parameter is guaranteed by design and/or device characterization. 2 Transmission Line Pulse (TLP) test setting : Std.TDR(50Ω),tp=100ns, tr=0.2ns ITLP and VTLP averaging window: star t1=70ns to end t2=80ns Wave Form 2/10µs Clamping Voltage vs. Peak Pulse Crrent (Line to GND) Capacitance vs. Reverse Bias(Line to GND) 29 26 23 20.0 Capacitance (pF) Clamp Voltage (VC) 25.0 15.0 10.0 20 17 14 11 8 5.0 70 80 90 100 Peak Pulse Current-IPP (A) ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/29/16 110 120 5 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 Bias Voltage (V) 2.4 2.7 3 3.3 TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- SP4042 Series Non-Repetitive Peak Pulse Power vs. Pulse Time Positive Transmission Line Pulsing (TLP) Plot (Line to GND) 25 20 10 TLP Current (A) Peak Pulse Power -PPP(kW) 100 1 15 10 5 0.1 0.1 1 10 100 1000 0 0 Peak Pulse Duraon -tP (µs) 2 4 6 TLP Volts (V) 8 10 Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Ramp-do Ramp-down Preheat TS(min) tS time to peak temperature Pre-Plated Frame Copper Alloy Lead Coplanarity 0.004 inches(0.102mm) Substrate material Silicon Body Material Molded Epoxy Flammability UL 94 V-0 Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4.. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Time Part Numbering System SP 4042-02 U T G G= Green TVS Diode Arrays (SPA® Diodes) T= Tape & Reel Series Number of Channels -02= 2 channel Lead Material Revision: 01/29/16 tL °C Product Characteristics Lead Plating Critical Zone TL to TP Ramp-up TL TS(max) 25 Peak Temperature (TP) +0/-5 tP TP Temperature Reflow Condition Package U= µDFN-10 Ordering Information Part Number Package Marking Min. Order Qty. SP4042-02UTG µDFN-10 A2*2 3000 Part Marking System A2 * 2 Number of Product Series Channels A2 = SP4042 Assembly Site TVS Diode Arrays (SPA®® Diodes) Lightning Surge Protection- SP4042 Series Package Dimensions — µDFN-10 Top View A D Package µDFN-10 (2.6x2.6mm) JEDEC MO-229 Millimeters Symbol E A Nom Max Min Nom Max 0.45 0.52 0.55 0.018 0.020 0.022 0.127Ref A3 B Side View 0.10 C 0.005 Ref b 0.17 0.22 0.27 0.006 0.009 0.011 D 2.50 2.60 2.70 0.098 0.102 0.106 0.087 D2 2.10 2.15 2.20 0.083 0.085 E 2.50 2.60 2.70 0.098 0.102 0.106 E2 1.21 1.26 1.31 0.048 0.050 0.052 0.45 0.014 0.50 BSC e A3 Inches Min 0.35 L 0.020 BSC 0.40 0.016 0.018 A Seating Plane 0.05 C C b RECOMMENDED SOLDER PAD 0.10 M C B A Bottom View D2 0.50 0.30 0.48 2.30 2X 0.48 1.32 2.68 C E2 2.23 e Unit: mm Embossed Carrier Tape & Reel Specification — µDFN-10 (2.6x2.6mm) P0 P2 P1 Reel Size:7 inches D0 E A0 F T W D1 K0 B0 Pin 1 Location User Feeding Direction ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 01/29/16 5º MAX 5º MAX Symbol Millimeters A0 2.82 +/- 0.05 B0 2.82 +/- 0.05 D0 Ø1.50 + 0.10 D1 Ø 0.50 + 0.05 E 1.75 +/- 0.10 F 3.50 +/- 0.05 K0 0.76 +/- 0.05 P0 4.00 +/- 0.10 P1 4.00 +/- 0.10 P2 2.00 +/- 0.05 T 0.25 +/- 0.02 W 8.00 + 0.30 /- 0.10