R41

Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC
(Automotive Grade)
Overview
Applications
The R41 Series is constructed of metallized polypropylene film
encapsulated with self-extinguishing resin in a box of material
meeting the requirements of UL 94 V–0.
For use in electromagnetic interference (EMI) suppression filter in "line-to-ground" and "across-the-line" applications requiring Y2 /
X1 safety classification. Suitable for use in situations where failure
of the capacitor could lead to danger of electric shock. Not for use
in "series with mains" type applications.
Automotive Grade devices are available (up to 22.5 mm Lead
Spacing) and meet the demanding Automotive Electronics
Council's AEC–Q200 qualification requirements.
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
Approvals: ENEC, UL, cUL, CQC
Class Y2 / X1 (IEC 60384-14)
Rated voltage: 300 VAC 50/60 Hz
Capacitance range: 0.001 – 1 µF
Lead spacing: 10 – 37.5 mm
Capacitance tolerance: ±20%, ±10%
Climatic category: 40/110/56, IEC 60068–1
Tape and reel in accordance with IEC 60286–2
RoHS Compliant and lead-free terminations
Operating temperature range of −40˚C to +110˚C
100% screening factory test at 5,000 VDC/2,500 VAC
Self-healing properties
Automotive (AEC–Q200) grades available up to
22.5 mm Lead Spacing
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Part Number System
R41
3
I
2330
00
M1
M
Series
Rated Voltage
(VAC)
Lead Spacing
(mm)
Capacitance Code
(pF)
Packaging
Internal Use
Capacitance
Tolerance
See Ordering
Options Table
00
M1
Y2, Metallized
Polypropylene
3 = 300
F = 10.0
I = 15.0
N = 22.5
R = 27.5
W = 37.5
The last three digits
represent significant
figures. The first
digit specifies
number of zeros to
be added.
K = ±10%
M = ±20%
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
1
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Ordering Options Table
Lead Spacing
Nominal (mm)
Lead Length
(mm)
Lead and
Packaging Code
4 +2/-0
H0= 18.5 +/-0.5
00
DQ
Tape & Reel (Large Reel)
H0= 18.5 +/-0.5
CK
Bulk (Bag) – Short Leads
3.5 +0.5/-0
JB
Bulk (Bag) – Short Leads
4.0 +0.5/-0
JE
Bulk (Bag) – Short Leads
3.2 +0.3/-0.2
JH
Bulk (Bag) – Long Leads
18 +1/-1
JM
Bulk (Bag) – Long Leads
30 +5/-0
40
Bulk (Bag) – Long Leads
25 +2/-1
50
4 +2/-0
H0= 18.5 +/-0.5
00
CK
30 +5/-0
25 +2/-1
40
50
4 +2/-0
00
30 +5/-0
25 +2/-1
40
50
Type of Leads and Packaging
Standard Lead and Packaging Options
Bulk (Bag) – Short Leads
Ammo Pack
Other Lead and Packaging Options
10,
15,
22.5
Standard Lead and Packaging Options
27.5
Bulk (Bag) – Short Leads
Tape & Reel (Large Reel)
Other Lead and Packaging Options
Bulk (Bag) – Long Leads
Bulk (Bag) – Long Leads
Standard Lead and Packaging Options
Bulk (Bag) – Short Leads
37.5
Other Lead and Packaging Options
Bulk (Bag) – Long Leads
Bulk (Bag) – Long Leads
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
2
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Dimensions – Millimeters
FRONT VIEW
SIDE VIEW
L
B
H
d
LL
p
p
B
H
L
d
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
10.0
10.0
10.0
15.0
15.0
15.0
15.0
15.0
22.5
22.5
22.5
22.5
22.5
27.5
27.5
27.5
37.5
37.5
37.5
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
+/-0.4
4.0
5.0
6.0
5.0
6.0
7.5
8.5
11.0
6.0
7.0
8.5
10.0
13.0
13.0
14.0
18.0
13.0
16.0
20.0
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.3
+0.3
+0.3
9.0
11.0
12.0
11.0
12.0
13.5
14.5
19.0
15.0
16.0
17.0
18.5
22.0
22.0
28.0
33.0
24.0
28.5
40.0
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
13.0
13.0
13.0
18.0
18.0
18.0
18.0
18.0
26.5
26.5
26.5
26.5
26.5
32.0
32.0
32.0
41.5
41.5
41.5
+0.2
+0.2
+0.2
+0.3
+0.3
+0.5
+0.5
+0.5
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
+/-0.05
Note: See Ordering Options Table for lead length (LL/H0) options.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
3
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Performance Characteristics
Dielectric
Plates
Winding
Leads
Protection
Polypropylene film
Metal layer deposited by evaporation under vacuum
Non-inductive type
Tinned wire
Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94.
Related documents
IEC 60384-14, EN 60384-14
Rated Voltage (VR)
300 VAC (50/60 Hz), 1,000 VDC
Capacitance Range
0.0010 µF to 1 µF
Capacitance Values
E6 series (IEC 60063)
Capacitance Tolerance
Temperature Range
Climatic Category
±10%, ±20%
−40ºC to +110°C
40/110/56 IEC 60068-1
Storage time: ≤ 24 months from the date marked on the label package
Average relative humidity per year ≤ 70%
Storage Conditions
RH ≤ 85% for 30 days randomly distributed throughout the year
Dew is absent
Temperature: −40 to 80°C (see "Maximum Humidity in Storage Conditions" graph below)
Approvals
ENEC, UL, cUL, CQC
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
4
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Performance Characteristics cont'd
Dissipation Factor (tanδ)
Test Voltage Between Terminals
≤ 0.3% (0.2%*) at 1kHz , +25°C ±5°C (* typical value)
The 100% screening factory test is carried out at 5,000 VDC/2,500 VAC. The voltage level is selected to meet the
requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not
permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures.
Measured at +25°C ±5°C, according to IEC 60384–2
Insulation Resistance
Minimum Values Between Terminals
Voltage Charge
Voltage Charge Time
C ≤ 0.33 μF
C > 0.33 μF
1 min
≥ 1 • 105 MΩ
( ≥ 5 • 105 MΩ )*
≥ 30,000 MΩ • µF
( ≥ 150,000 MΩ • µF )*
100 VDC
In DC Applications
Recommended voltage ≤ 1,000 VDC
* Typical value
Qualification
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test
methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional
information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.
Impedance Graph
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
5
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Environmental Test Data
Test
IEC Publication
Procedure
Endurance
EN/IEC 60384–14
Vibration
IEC 60068–2–6 Test Fc
3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2
Bump
IEC 60068–2–29 Test Eb
1,000 bumps at 390 m/s2
Change of Temperature
IEC 60068–2–14 Test Na
Upper and lower rated temperature 5 cycles
Active Flammability
IEC 60384–14
VR + 20 surge pulses at 5 kV (pulse every 5 seconds)
Passive Flammability
IEC 60384–14
IEC 60384–1, IEC 60695–11–5 Needle flame test
Damp Heat Steady State
IEC 60068–2–78 Test Cab
1.7 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second,
1,000 hours at upper rated temperature
+40°C and 93% RH, 56 days
Approvals
Mark
Specification
File Number
EN/IEC 60384-14
V4160
UL 60384-14 and
CAN/CSA E60384-14
(300 VAC)
E97797
IEC 60384-14
CQC13001087758
CQC13001101264
CQC14001116018
CQC14001116611
Environmental Compliance
All KEMET EMI capacitors are RoHS Compliant.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
6
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Table 1 – Ratings & Part Number Reference
Dimensions in mm
Capacitance
Value (µF)
L
Lead Spacing
(p)
dV/dt
(V/µs)
New KEMET
Part Number
B
H
Legacy Part Number
0.0010
0.0015
0.0022
0.0033
0.0047
0.0068
0.0033
0.0047
0.0068
0.010
0.015
0.022
0.033
0.047
0.068
0.047
0.068
0.068
0.10
0.15
0.22
0.22
0.33
0.47 0.68
0.47
0.68
1.0
4.0
4.0
4.0
4.0
5.0
6.0
5.0
5.0
5.0
5.0
5.0
6.0
7.5
8.5
11.0
6.0
6.0
7.0
8.5
10.0
13.0
13.0
14.0
18.0
18.0
13.0
16.0
20.0
9.0
9.0
9.0
9.0
11.0
12.0
11.0
11.0
11.0
11.0
11.0
12.0
13.5
14.5
19.0
15.0
15.0
16.0
17.0
18.5
22.0
22.0
28.0
33.0
33.0
24.0
28.5
40.0
13.0
13.0
13.0
13.0
13.0
13.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
26.5
26.5
26.5
26.5
26.5
26.5
32.0
32.0
32.0
32.0
41.5
41.5
41.5
10.0
10.0
10.0
10.0
10.0
10.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
22.5
22.5
22.5
22.5
22.5
22.5
27.5
27.5
27.5
27.5
37.5
37.5
37.5
800
800
800
800
800
800
600
600
600
600
600
600
600
600
600
500
500
500
500
500
500
400
400
400
400
300
300
300
413F1100(1)00(2)
413F1150(1)00(2)
413F1220(1)00(2)
413F1330(1)M1(2)
413F1470(1)M1(2)
413F1680(1)00(3)
413I1330(1)00(2)
413I1470(1)00(2)
413I1680(1)00(2)
413I2100(1)00(2)
413I2150(1)M1(2)
413I2220(1)M1(2)
413I2330(1)M1(2)
413I2470(1)M1(2)
413I2680(1)00(2)
413N2470(1)00(2)
413N2680(1)M1(3)
413N2680(1)00(2)
413N3100(1)M1(2)
413N3150(1)M1(2)
413N3220(1)00(2)
413R3220(1)00(2)
413R3330(1)00(2)
413R3470(1)00(2)
413R3680(1)00(2)
413W 3470(1)00(2)
413W 3680(1)00(2)
413W 4100(1)00(2)
R413F1100(1)00(2)
R413F1150(1)00(2)
R413F1220(1)00(2)
R413F1330(1)M1(2)
R413F1470(1)M1(2)
R413F1680(1)00(3)
R413I1330(1)00(2)
R413I1470(1)00(2)
R413I1680(1)00(2)
R413I2100(1)00(2)
R413I2150(1)M1(2)
R413I2220(1)M1(2)
R413I2330(1)M1(2)
R413I2470(1)M1(2)
R413I2680(1)00(2)
R413N2470(1)00(2)
R413N2680(1)M1(3)
R413N2680(1)00(2)
R413N3100(1)M1(2)
R413N3150(1)M1(2)
R413N3220(1)00(2)
R413R3220(1)00(2)
R413R3330(1)00(2)
R413R3470(1)00(2)
R413R3680(1)00(2)
R413W 3470(1)00(2)
R413W 3680(1)00(2)
R413W 4100(1)00(2)
Capacitance Value (µF)
B (mm)
H (mm)
L (mm)
Lead
Spacing (p)
dV/dt (V/µs)
New KEMET
Part Number
Legacy Part Number
(1) Insert lead and packaging code. See Ordering Options Table for available options.
(2) M = ±20%, K = ±10%
(3) M = ±20% (only available tolerance).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
7
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Soldering Process
The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has
increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221ºC for the new alloys. As a result, the heat stress
to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene
capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170ºC). Wave soldering can be destructive, especially
for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The
recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve
from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1.
Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the
recommended limits may result to degradation or permanent damage to the capacitors.
Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert throughhole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole
components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the
capacitor surface temperature to return to a normal temperature before the second soldering cycle.
Manual Soldering Recommendations
Wave Soldering Recommendations
300
Following is the recommendation for manual
soldering with a soldering iron.
2+3s max
260°C
250
First wave
Temperature (°C)
Recommended Soldering Temperature
Soldering iron bit temperature (deg C)
400
350
300
250
Second wave
200
Cooling
ΔT <150°C
Preheating
150
ca 2°C/s
ca 3.5°C/s typical
Tpreheat
100
ca 5°C/s
115°C max
100°C
Typical
200
50
150
100
0
0
50
40
80
120
160
200
240
Time (s)
0
0
1
2
3
4
5
6
7
8
Soldering time (sec)
The soldering iron tip temperature should be set
at 350°C (+10°C maximum) with the soldering
duration not to exceed more than 3 seconds.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
8
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Soldering Process cont'd
Wave Soldering Recommendations cont'd
1. The table indicates the maximum set-up temperature of the soldering process
Figure 1
Dielectric
Film Material
Maximum Preheat
Temperature
Maximum
Peak Soldering
Temperature
Capacitor Capacitor Capacitor Capacitor Capacitor
Pitch
Pitch
Pitch
Pitch
Pitch
≤ 10 mm = 15 mm > 15 mm ≤ 15 mm > 15 mm
Polyester
130°C
130°C
130°C
270°C
270°C
Polypropylene
100°C
110°C
130°C
260°C
270°C
Paper
130°C
130°C
140°C
270°C
270°C
Polyphenylene
Sulphide
150°C
150°C
160°C
270°C
270°C
2. The maximum temperature measured inside the capacitor:
Set the temperature so that inside the element the maximum temperature is below the limit:
Dielectric Film Material
Maximum temperature
measured inside the element
Polyester
160°C
Polypropylene
110°C
Paper
160°C
Polyphenylene
sulphide
160°C
Temperature monitored inside the capacitor.
Selective Soldering Recommendations
Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be
soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is
over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected
components, and pressed against the lower surface of the board to solder the components.
The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead
of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than
in double wave flow soldering, and great care must be taken so that the parts are not overheated.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
9
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Construction
2 Sections
Molded Plastic
Case
Single-sided Metallized
Polypropylene Film
(First Layer)
Detailed Cross Section
Molded Plastic
Case
Self-Extinguishing
Resin
Single-sided Metallized
Polypropylene Film
(Second Layer)
Margin
Margin
Metal Contact
Layer
Metal Contact
Layer
FILM WINDINGMargin
SCHEME OPTIONS
Leads
etallized Polypropylene Film
Double-sided Metallized Polyester Film
Winding Scheme
sided
zed
pylene
m
Single-sided
Metallized
Polypropylene
Film
Double-sided
Metallized
Polyester Carrier
Film
Single-sided
Metallized
Polypropylene
Film
4 Sections
Double-sided
Metallized
Polyester Carrier
Film
Polypropylene
Film Dielectric
Double-sided
Metallized
Polyester Carrier
Film
3 Sections
©Metallized
KEMET Electronics
Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Polyphenylene
Sulfide Film (SMR)
2 Sections
1 Section
2 Sections
sided
zed
pylene
m
Polypropylene
Film Dielectric
Double-sided
Metallized
Polyester Carrier
Film
4 Sections
F3100_R41_Y2_300 • 6/9/2016
Polypropylene Film/Foil
10
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Marking
Lead Spacing 10 mm
FRONT
TOP
Capacitance Tolerance
Series,
Dielectric Code,
Safety Class,
Self Healing
Approval
Marks
Manufacturer’s
Logo
Capacitance,
Rated Voltage
IEC Climatic
Category
Date Code
Passive Flammability
Category
Manufacturing
Plant
Lead Spacing 15 mm, 22.5 mm (small case sizes)
FRONT
TOP
Capacitance Tolerance
Series,
Dielectric Code,
Safety Class,
Self Healing
Approval
Marks
Manufacturer’s
Logo
Capacitance,
Rated Voltage
IEC Climatic
Category
Date Code
Passive Flammability Category:
B for volume ≥ 1750 mm3
C for volume < 1750 mm3
Manufacturing
Plant
Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm
FRONT
TOP
Series
Approval
Marks
Dielectric
Code
Safety
Class
Self
Healing
Manufacturer’s
Logo
Capacitance,
Capacitance
Tolerance,
Rated Voltage
IEC Climatic
Category
QA Number
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Passive
Flammability
Category
F3100_R41_Y2_300 • 6/9/2016
Date Code
Manufacturing
Plant
11
IEC Climatic
Category
Date Code
Manufacturing
Plant
Metallized Polypropylene Film EMI
Suppression
Capacitors
Passive
Flammability
Category:
B
for
volume
≥
1750
mm3
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive
Grade)
C for volume < 1750 mm3
Marking cont'd
Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm
FRONT
TOP
Series
Approval
Marks
Dielectric
Code
Safety
Class
Self
Healing
Manufacturer’s
Logo
Capacitance,
Capacitance
Tolerance,
Rated Voltage
IEC Climatic
Category
QA Number
Passive
Flammability
Category
Manufacturing
Plant
Date Code
Manufacturing Date Code (IEC 60062)
Y = Year, Z = Month
Year
Code
Month
Code
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
M
N
P
R
S
T
U
V
W
X
A
B
C
D
E
F
H
J
K
L
M
January
February
March
April
May
June
July
August
September
October
November
December
1
2
3
4
5
6
7
8
9
O
N
D
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
12
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Packaging Quantities
Height
(mm)
Length
(mm)
Bulk
Short Leads
Bulk
Long Leads
Standard
Reel
ø 355 mm
Large Reel
ø 500 mm
Ammo
Taped
10
4.0
5.0
6.0
9.0
11.0
12.0
13.0
13.0
13.0
2000
1300
1000
1800
1500
1200
750
600
500
1500
1250
1000
1000
800
680
15
5.0
6.0
7.5
8.5
11.0
11.0
12.0
13.5
14.5
19.0
18.0
18.0
18.0
18.0
18.0
2000
1750
1000
1000
450
1000
900
700
500
350
600
500
350
300
–
1250
1000
800
700
500
800
680
500
440
340
22.5
6.0
7.0
8.5
10.0
13.0
15.0
16.0
17.0
18.5
22.0
26.5
26.5
26.5
26.5
26.5
805
700
468
396
300
500
500
300
300
200
–
–
–
–
–
700
550
450
350
300
464
380
280
235
–
27.5
13.0
14.0
18.0
22.0
28.0
33.0
32.0
32.0
32.0
480
352
256
288
176
128
–
–
–
300
–
–
–
–
–
37.5
13.0
16.0
20.0
24.0
28.5
40.0
41.5
41.5
41.5
360
216
126
216
108
84
–
–
–
–
–
–
–
–
–
Lead Spacing Thickness
(mm)
(mm)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
13
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Lead Taping & Packaging (IEC 60286–2)
Figure 1
Lead Spacing 10 mm
Figure 2
Lead Spacing 15 mm
Figure 3
Lead Spacing 22.5 – 27.5 mm
P
W2
P2
P
h
h
W
W0
W1
H0
ød
P1 P0
F
D0
t
P1
P2
Taping Specification
Dimensions (mm)
Description
Symbol
10
Fig. 1
Lead Space
15
22.5
Fig. 2
Fig. 3
27.5
Fig. 3
Tol.
Lead wire diameter
d
0.6
0.6-0.8
0.8
0.8
±0.05
Taping lead space
P
25.4
25.4
38.1
38.1
±1
Feedholeleadspace*
P0
12.7
12.7
12.7
12.7
±0.2**
Centering of the lead wire
P1
7.7
5.2
7.8
5.3
±0.7
Centering of the body
P2
12.7
12.7
19.05
19.05
±1.3
Leadspacing(pitch)***
F
10
15
22.5
27.5
+0.6/-0.1
Component alignment
∆h
0
0
0
0
±2
Height of component
from tape center
H 0****
18.5
18.5
18.5
18.5
±0.5
Carrier tape width
W
18
18
18
18
+1/-0.5
Hold down tape width
W0
9
10
10
10
Minimum
Hole position
W1
9
9
9
9
±0.5
Hold down tape position
W2
3
3
3
3
Maximum
Feed hole diameter
D0
4
4
4
4
±0.2
t
0.7
0.7
0.7
0.7
±0.2
Tape thickness
* Also available in 15 mm.
** Max 1 mm on 20 lead spaces.
*** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request.
**** H0 = 16.5 mm available upon request.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
14
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Lead Taping & Packaging (IEC 60286–2) cont'd
Ammo Specifications
Dimensions (mm)
H
W
T
360
340
59
H
T
W
Reel Specifications
Reel Size
Standard
Large
Dimensions (mm)
D
H
W
355
500
30
25
55 Maximum
D
H
W
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
15
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Skopje, Macedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Wyboston, United Kingdom
Tel: 44-1480-273082
Taipei, Taiwan
Tel: 886-2-27528585
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
2835 KEMET Way
Simpsonville, SC 29681
Northeast
Wilmington, MA
Tel: 978-658-1663
Southeast
Lake Mary, FL
Tel: 407-855-8886
Central
Novi, MI
Tel: 248-994-1030
Beijing, China
Tel: 86-10-5877-1075
Shanghai, China
Tel: 86-21-6447-0707
Seoul, South Korea
Tel: 82-2-6294-0550
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Irving, TX
Tel: 972-915-6041
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
16
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class Y2, 300 VAC, 110ºC (Automotive Grade)
Disclaimer
Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare
notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F3100_R41_Y2_300 • 6/9/2016
17