Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Overview Applications The R79 Series is constructed of metallized polypropylene film with radial leads of tinned wire. The radial leads are electrically welded to the metal layer on the ends of the capacitor winding. The capacitor is encapsulated with a self-extinguishing thermosetting resin in a box material meeting the UL 94V–0 requirements. Typical applications include timing, oscillator circuits, high frequency coupling and decoupling applications. Not suitable for across-the-line application (see Suppressor Capacitors). Benefits • Voltage range: 160 – 630 VDC • Capacitance range: 0.001 – 0.22 µF • Lead Spacing: 5 mm • Capacitance tolerance: ±5%, ±10%, ±20% • Climatic category: 55/105/56 IEC 60068-1 • Operating temperature range of -55˚C to +105˚C • RoHS compliance and lead-free terminations • Tape and reel packaging in accordance with IEC 60286–2 •Self-healing Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Part Number System R79 Series Metallized Polypropylene G C Rated Voltage (VDC) Lead Spacing (mm) G = 160 I = 250 M = 400 P = 630 C=5 2390 Capacitance Code (pF) The last three digits represent significant figures. The first digit specifies the total number of zeros to be added. AA 40 Packaging Internal Use See Ordering Options Table 40 45 K Capacitance Tolerance H = 2.5% J = ±5% K = ±10% One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 1 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Ordering Options Table Lead Spacing Nominal (mm) Type of Leads and Packaging Lead Length (mm) Lead and Packaging Code 4 +1.5/-0 H0=18.5 +/- 0.5 AA DQ H0=18.5 +/- 0.5 10 +/- 1 4.0 +0.5/-0 3.2 +0.3/-0.2 17 +1/-2 CK JC JE JH Z3 Standard Lead and Packaging Options Bulk (Bag)–Short Leads Ammo Pack Other Lead and Packaging Options 5 Tape &Reel (Standard Reel) Bulk (Bag)–Short Leads Bulk (Bag)–Short Leads Bulk (Bag)–Short Leads Bulk (Bag)–Long Leads Dimensions – Millimeters FRONT VIEW SIDE VIEW L B H d 0.5 LL p p B H L d Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 5.0 5.0 5.0 5.0 5.0 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 3.5 4.5 5.0 6.0 7.2 +0.1 +0.1 +0.1 +0.1 +0.1 7.5 9.5 10.0 11.0 13.0 +0.1 +0.1 +0.1 +0.1 +0.1 7.2 7.2 7.2 7.2 7.2 +0.2 +0.3 +0.3 +0.3 +0.3 0.6 0.6 0.6 0.6 0.6 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 Note: See Ordering Options Table for lead length (LL/Ho) options. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 2 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Performance Characteristics Dielectric Plates Winding Leads Protection Related Documents Polypropylene film Metal layer deposited by evaporation under vacuum Non-inductive type Tinned wire Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. IEC 60384-16 Rated Voltage VR (VDC) 160 250 400 630 Rated Voltage VR (VAC) 70 160 200 220 Capacitance Range (µF) 0.039 – 0.22 0.012 – 0.15 0.0039 – 0.047 0.001 – 0.018 Capacitance Values Capacitance Tolerance Operating Temperature Range Rated Temperature TR Voltage Derating E12 series (IEC 60063) measured @ 1 kHz and +20 ±1°C ±2.5%, ±5%, ±10% -55°C to +105°C +85°C Above +85°C DC and AC voltage derating is 1.25%/°C 55/105/56 IEC 60068-1 Climatic Category Average relative humidity ≤ 75% RH = 95% for 30 days per year RH = 85% for further days limited by average value per year Test Voltage Capacitance Drift Maximum Pulse Steepness Temperature Coefficient Self Inductance 1.6 x VR VDC for 2 seconds (between terminations) @ +25°C ±5°C Maximum 0.5% after a 2 year storage period at a temperature of +10°C to +40°C and a relative humidity of 40% to 60% dV/dt according to Table 1. For peak to peak voltages lower than rated voltage (Vpp <VR), the specified dv/dt can be multiplied by the factor VR /Vpp -(200 ±100) ppm/°C at 1 kHz Approximately 6 nH. Max 1 nH per 1 mm lead and capacitor length. Maximum Values @ 25°C ±5°C Dissipation Factor tanδ Frequency C ≤ 0.1 μF C > 1 µF 1 kHz 0.06% 0.06% 10 kHz 0.10% 0.10% 100 kHz 0.30% - Measured @ +25°C ±5°C, 100 VDC 60 seconds Insulation Resistance Minimum Values Between Terminals All Capacitance Values ≥ 100,000 MΩ ( ≥ 500,000 MΩ ) * * typical value © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 3 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Maximum Voltage (Vrms) vs. Frequency (Sinusoidal Waveform/Th ≤ 40ºC) 160Vdc / 70Vac Vrms [V] 1000 100 100 10 1 250Vdc / 160Vac Vrms [V] 1000 10 0.068 µF p=5 0.1 µF p=5 0.22 µF p=5 1 0.1 1 Vrms [V] 1000 f [kHz] 10 100 1000 400Vdc / 200Vac 0.1 f [kHz] 1 10 100 1000 100 1000 630Vdc / 220Vac Vrms [V] 1000 100 100 10 1 0.022 µF p=5 0.047 µF p=5 0.1 µF p=5 10 4700 pF p=5 0.015µF p=5 0.047µF p=5 0.1 1 f [kHz] 10 100 1000 1 2200 pF p=5 4700 pF p=5 0.01 µF p=5 0.1 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com f [kHz] 10 F3107_R79 • 5/29/2015 4 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Maximum Current (Irms) vs. Frequency (Sinusoidal Waveform/Th ≤ 40ºC) Irms [A] Irms [A] 160Vdc / 70Vac 100 10 10 1 1 0.068 µF p=5 0.1 µF p=5 0.22 µF p=5 0.1 0.01 0.1 1 Irms [A] f [kHz] 10 100 0.022 µF p=5 0.047 µF p=5 0.1 µF p=5 0.1 1000 0.01 0.1 1 Irms [A] 400Vdc / 200Vac 100 250Vdc / 160Vac 100 10 1 1 0.1 10 1000 0.1 4700 pF p=5 0.015 µF p=5 0.047 µF p=5 0.01 100 630Vdc / 220Vac 100 10 f [kHz] 0.1 1 f [kHz] 10 100 2200 pF p=5 4700 pF p=5 0.01 µF p=5 1000 0.01 0.1 1 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com f [kHz] 10 100 1000 F3107_R79 • 5/29/2015 5 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Environmental Test Data Damp Heat, Steady State Test Test Conditions: Temperature: Relative humidity (RH): Test duration: Endurance Test +40°C ± 2°C 93% ± 2% 56 days Performances │Δ C/C│ ≤ 3%, Δ tanδ ≤ 0.001 @ 1 kHz IR after test ≥ 50% of initial limit Test Conditions Temperature: Voltage applied: Test duration: Resistance to Soldering Heat Test +85°C ±2°C 1.25 x VR (DC) 2,000 hours Performances │Δ C/C│ ≤ 3%, Δ tanδ ≤ 0.001 @10 kHz IR after test ≥ 50% of initial limit Test Conditions Solder bath temperature: Dipping time (with heat screen): 260°C ±5°C 10 seconds ±1 second Performances │Δ C/C│ ≤ 2%, Δ tanδ ≤ 0.001 @10 kHz for C ≤ 1µF IR after test ≥ initial limit Environmental Compliance All KEMET pulse capacitors are RoHS Compliant. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 6 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Table 1 – Ratings & Part Number Reference VDC VAC Capacitance Value (µF) 160 160 160 160 160 160 160 160 160 160 250 250 250 250 250 250 250 250 250 250 250 250 250 250 400 400 400 400 400 400 400 400 400 400 400 400 400 400 630 630 630 630 630 630 630 630 630 630 630 630 630 630 630 630 70 70 70 70 70 70 70 70 70 70 160 160 160 160 160 160 160 160 160 160 160 160 160 160 200 200 200 200 200 200 200 200 200 200 200 200 200 200 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.0039 0.0047 0.0056 0.0068 0.0082 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.006 0.007 0.008 0.010 0.012 0.015 0.018 VDC VAC Capacitance Value (µF) Dimensions in mm B H L Lead Spacing (p) dV/dt (V/µs) Max K0 (V2/µs) New KEMET Part Number Legacy Part Number 3.5 4.5 4.5 4.5 5.0 5.0 6.0 6.0 7.2 7.2 3.5 3.5 3.5 3.5 3.5 3.5 4.5 4.5 4.5 5.0 6.0 6.0 7.2 7.2 3.5 3.5 3.5 3.5 3.5 3.5 4.5 4.5 5.0 5.0 6.0 6.0 7.2 7.2 3.5 3.5 3.5 3.5 3.5 3.5 3.5 4.5 4.5 4.5 5.0 5.0 6.0 6.0 7.2 7.2 7.5 9.5 9.5 9.5 10.0 10.0 11.0 11.0 13.0 13.0 7.5 7.5 7.5 7.5 7.5 7.5 9.5 9.5 9.5 10.0 11.0 11.0 13.0 13.0 7.5 7.5 7.5 7.5 7.5 7.5 9.5 9.5 10.0 10.0 11.0 11.0 13.0 13.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 9.5 9.5 9.5 10.0 10.0 11.0 11.0 13.0 13.0 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 100 100 100 100 100 100 100 100 100 100 250 250 250 250 250 250 250 250 250 250 250 250 250 250 400 400 400 400 400 400 400 400 400 400 400 400 400 400 500 500 500 500 500 500 500 600 600 600 600 600 600 600 600 600 32,000 32,000 32,000 32,000 32,000 32,000 32,000 32,000 32,000 32,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 125,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 320,000 630,000 630,000 630,000 630,000 630,000 630,000 630,000 756,000 756,000 756,000 756,000 756,000 756,000 756,000 756,000 756,000 79GC2390(1)40(2) 79GC2470(1)40(2) 79GC2560(1)40(2) 79GC2680(1)40(2) 79GC2820(1)40(2) 79GC3100(1)40(2) 79GC3120(1)40(2) 79GC3150(1)40(2) 79GC3180(1)40(2) 79GC3220(1)40(2) 79IC2120(1)45(2) 79IC2150(1)45(2) 79IC2180(1)45(2) 79IC2220(1)45(2) 79IC2270(1)45(2) 79IC2330(1)40(2) 79IC2390(1)40(2) 79IC2470(1)40(2) 79IC2560(1)40(2) 79IC2680(1)40(2) 79IC2820(1)40(2) 79IC3100(1)40(2) 79IC3120(1)40(2) 79IC3150(1)40(2) 79MC1390(1)40(2) 79MC1470(1)40(2) 79MC1560(1)40(2) 79MC1680(1)40(2) 79MC1820(1)40(2) 79MC2100(1)40(2) 79MC2120(1)40(2) 79MC2150(1)40(2) 79MC2180(1)40(2) 79MC2220(1)40(2) 79MC2270(1)40(2) 79MC2330(1)40(2) 79MC2390(1)40(2) 79MC2470(1)40(2) 79PC1100(1)40(2) 79PC1120(1)40(2) 79PC1150(1)40(2) 79PC1180(1)40(2) 79PC1220(1)40(2) 79PC1270(1)40(2) 79PC1330(1)40(2) 79PC1390(1)40(2) 79PC1470(1)40(2) 79PC1560(1)40(2) 79PC1680(1)40(2) 79PC1820(1)40(2) 79PC2100(1)40(2) 79PC2120(1)40(2) 79PC2150(1)40(2) 79PC2180(1)40(2) R79GC2390(1)40(2) R79GC2470(1)40(2) R79GC2560(1)40(2) R79GC2680(1)40(2) R79GC2820(1)40(2) R79GC3100(1)40(2) R79GC3120(1)40(2) R79GC3150(1)40(2) R79GC3180(1)40(2) R79GC3220(1)40(2) R79IC2120(1)45(2) R79IC2150(1)45(2) R79IC2180(1)45(2) R79IC2220(1)45(2) R79IC2270(1)45(2) R79IC2330(1)40(2) R79IC2390(1)40(2) R79IC2470(1)40(2) R79IC2560(1)40(2) R79IC2680(1)40(2) R79IC2820(1)40(2) R79IC3100(1)40(2) R79IC3120(1)40(2) R79IC3150(1)40(2) R79MC1390(1)40(2) R79MC1470(1)40(2) R79MC1560(1)40(2) R79MC1680(1)40(2) R79MC1820(1)40(2) R79MC2100(1)40(2) R79MC2120(1)40(2) R79MC2150(1)40(2) R79MC2180(1)40(2) R79MC2220(1)40(2) R79MC2270(1)40(2) R79MC2330(1)40(2) R79MC2390(1)40(2) R79MC2470(1)40(2) R79PC1100(1)40(2) R79PC1120(1)40(2) R79PC1150(1)40(2) R79PC1180(1)40(2) R79PC1220(1)40(2) R79PC1270(1)40(2) R79PC1330(1)40(2) R79PC1390(1)40(2) R79PC1470(1)40(2) R79PC1560(1)40(2) R79PC1680(1)40(2) R79PC1820(1)40(2) R79PC2100(1)40(2) R79PC2120(1)40(2) R79PC2150(1)40(2) R79PC2180(1)40(2) B (mm) H (mm) L (mm) Lead Spacing (p) dV/dt (V/µs) Max K0 (V2 /µs) New KEMET Part Number Legacy Part Number (1) Insert lead and packaging code. See Ordering Options Table for available options. (2) J = 5%, K = 10%, M = 20% © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 7 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221ºC for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170ºC). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert throughhole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Manual Soldering Recommendations Wave Soldering Recommendations 300 Following is the recommendation for manual soldering with a soldering iron. 2+3s max 260°C 250 First wave Temperature (°C) Recommended Soldering Temperature Soldering iron bit temperature (deg C) 400 350 300 250 Second wave 200 Cooling ΔT <150°C Preheating 150 ca 2°C/s ca 3.5°C/s typical Tpreheat 100 ca 5°C/s 115°C max 100°C Typical 200 50 150 100 0 0 50 40 80 120 160 200 240 Time (s) 0 0 1 2 3 4 5 6 7 8 Soldering time (sec) The soldering iron tip temperature should be set at 350°C (+10°C maximum) with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 8 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Soldering Process cont'd Wave Soldering Recommendations cont'd 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch Pitch ≤ 10 mm = 15 mm > 15 mm ≤ 15 mm > 15 mm Polyester 130°C 130°C 130°C 270°C 270°C Polypropylene 100°C 110°C 130°C 260°C 270°C Paper 130°C 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 9 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Construction Wound Single-sided Metallized Polypropylene Film (First Layer) Molded Plastic Case Single-sided Metallized Polypropylene Film (Second Layer) Detailed Cross Section Molded Plastic Case Self-Extinguishing Resin Margin Margin Metal Contact Layer Metal Contact Layer Margin FILM WINDING SCHEME OPTIONS Leads Single-sided Metallized Polypropylene Film Double-side Winding Scheme Single-sided Metallized Polypropylene Film 1 Section Single-sided Metallized Polypropylene Film 2 Sections Single-sided Metallized Polypropylene Film 3 Sections Double-sided Metallized Polyester Carrier Film Polyprop Film Diel 1 Section Single-sided Metallized Polypropylene Film 4 Sections © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Metallized Impregnated Paper Metallized Polyphenylene Sulfide Film (SMR) Double-sided Metallized Polyester Carrier Film Polyprop Film Diel 3 Sections F3107_R79 • 5/29/2015 10 Poly Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Marking FRONT TOP Series Capacitance Capacitance Tolerance Voltage Code Packaging Quantities Lead Spacing Thickness (mm) Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads Standard Reel ø 355 mm 5 3.5 4.5 5.0 6.0 7.2 7.5 9.5 10 11 13 7.2 7.2 7.2 7.2 7.2 2,000 1,500 1,000 2,000 1,500 3,000 2,000 1,500 1,000 750 1,800 1,400 1,200 1,000 800 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Large Reel ø 500 mm Ammo Taped 2,500 1,900 1,700 1,400 1,150 F3107_R79 • 5/29/2015 11 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Lead Taping & Packaging (IEC 60286–2) Lead Spacing 5 mm Taping Specification Description Dimensions (mm) Symbol Lead Spacing 5 Tolerance Lead wire diameter d 0.5 ±0.05 Taping lead space P 12.7 ±1 Feed hole lead space P0 12.7 ±0.2** Centering of the lead wire P1 3.85 ±0.7 Centering of the body P2 6.35 ±1.3 Lead spacing F 5 +0.6/-0.1 Component alignment Dh 0 ±2 Height of component from tape center H 0* 18.5 ±0.5 Carrier tape width W 18 +1/-0.5 Hold down tape width W0 6 Minimum Hole position W1 9 ±0.5 Hold down tape position W2 3 Maximum Feed hole diameter D0 4 ±0.2 t 0.7 ±0.2 Tape thickness *H0 = 16.5 mm is available upon request. **Maximum 1 mm on 20 lead spacing. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 12 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Lead Taping & Packaging (IEC 60286–2) cont'd Ammo Specifications Dimensions (mm) H W T 360* 340 59 H * Lower dimension available upon request (Maximum 295 mm) T Reel Specifications W Dimensions (mm) D H W 355 30 55 Maximum D Manufacturing Date Code (IEC–60062) H Y = Year, Z = Month Year 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 Code M N P R S T U V W X A B C D E F H J K L M Month January February March April May June July August September October November December Code 1 2 3 4 5 6 7 8 9 O N D © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com W F3107_R79 • 5/29/2015 13 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications KEMET Corporation World Headquarters Europe Asia Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel: 389-2-55-14-623 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Wyboston, United Kingdom Tel: 44-1480-273082 Taipei, Taiwan Tel: 886-2-27528585 Espoo, Finland Tel: 358-9-5406-5000 Southeast Asia Singapore Tel: 65-6701-8033 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 Central Novi, MI Tel: 248-994-1030 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 14 Film Capacitors – Polypropylene Pulse/High Frequency Capacitors R79 Series Single Metallized Polypropylene Film, Radial, 5 mm Lead Spacing, Multipurpose Applications Disclaimer Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3107_R79 • 5/29/2015 15