Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Overview Applications The R46 Series is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V–0. For worldwide use in electromagnetic interference (EMI) suppression in across-the-line applications requiring X2 safety classification. Intended for use in situations where capacitor failure would not result in exposure to electric shock. Not for use in "series with mains" type applications. Benefits • • • • • • • • • • • • Approvals: ENEC, UL, cUL Class X2 (IEC 60384-14) Rated voltage: 275 VAC 50/60 Hz Capacitance range: 0.01 – 1 µF Lead spacing: 10.0 – 22.5 mm Capacitance tolerance: ±20%, ±10% Climatic category: 40/125/56, IEC 60068–1 Tape and reel in accordance with IEC 60286–2 RoHS Compliant and lead-free terminations Operating temperature range of -40˚C to +125˚C 100% screening factory test at 2,200 VDC/1,500 VAC Self-healing properties Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Part Number System R46 K N 3220 00 H1 M Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance The last three digits represent significant figures. The first digit specifies number of zeros to be added. See Ordering Options Table H = High Temperature H1 H2 H3 H4 X2, Metallized Polypropylene K = 275 F = 10.0 I = 15.0 N = 22.5 K = ±10% M = ±20% One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 1 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Ordering Options Table Lead Spacing Nominal (mm) Lead Length (mm) Lead and Packaging Code 4 +2/-0 H0= 18.5 +/-0.5 00 DQ Tape & Reel (Large Reel) H0= 18.5 +/-0.5 CK Bulk (Bag) – Short Leads 2.7 +0.5/-0 JA Bulk (Bag) – Short Leads 3.5 +0.5/-0 JB Bulk (Bag) – Short Leads 4.0 +0.5/-0 JE Bulk (Bag) – Short Leads 3.2 +0.3/-0.2 JH Bulk (Bag) – Long Leads 18 +1/-1 JM Bulk (Bag) – Long Leads 30 +5/-0 40 Bulk (Bag) – Long Leads 25 +2/-1 50 Bulk (Bag) – Insulated Rigid Leads 30 +5/-0 (sp 8+2/-2) 51 Bulk (Bag) – Insulated Flexible Leads 150 +5/-5 (sp 8+2/-2) 52 Type of Leads and Packaging Standard Lead and Packaging Options Bulk (Bag) – Short Leads Ammo Pack Other Lead and Packaging Options 10, 15, 22.5 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 2 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Dimensions – Millimeters Loose Insulated Rigid Leads Insulated Flexible Leads 0.5 mm2 FRONT VIEW SIDE VIEW FRONT VIEW SIDE VIEW FRONT VIEW SIDE VIEW L B L B L B H H d H LL B H d L 8 ±2 8 ±2 d p 150 ±5 35 +0/-5 p d Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 +/-0.4 5.0 6.0 5.0 6.0 6.0 7.5 7.5 8.5 9.0 10.0 11.0 13.0 6.0 7.0 10.0 11.0 13.0 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 11.0 12.0 11.0 12.0 17.5 13.5 18.5 14.5 12.5 16.0 19.0 12.0 15.0 16.0 18.5 20.0 22.0 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 +0.2 +0.2 +0.3 +0.3 +0.3 +0.5 +0.5 +0.5 +0.5 +0.5 +0.5 +0.5 +0.3 +0.3 +0.3 +0.3 +0.3 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 +/-0.05 Note: See Ordering Options Table for lead length (LL/H 0) options. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 3 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Performance Characteristics Dielectric Plates Winding Leads Protection Polypropylene film Metal layer deposited by evaporation under vacuum Non-inductive type Tinned wire Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. Related documents IEC 60384-14, EN 60384-14 Rated Voltage (VR) 275 VAC (50/60 Hz), 560 VDC Capacitance Range 0.010 µF to 1 µF Capacitance Values E6 series (IEC 60063) measured @ 1 kHz and +20 ±1°C Capacitance Tolerance Temperature Range Climatic Category Approvals Dissipation Factor (tanδ) Test Voltage Between Terminals ±10%, ±20% -40ºC to +125°C 40/125/56 IEC 60068-1 ENEC, UL, cUL ≤ 0.1% (0.06%*) @ 1kHz , +25°C ±5°C (* typical value) The 100% screening factory test is carried out at 2,200 VDC/1,500 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Measured at +25°C ±5°C, according to IEC 60384–2 Minimum Values Between Terminals Insulation Resistance Voltage Charge Voltage Charge Time C ≤ 0.33 μF C > 0.33 μF 1 min ≥ 1 • 10 MΩ ( ≥ 5 • 105 MΩ )* * typical value ≥ 30,000 MΩ • µF ( ≥ 150,000 MΩ • µF )* * typical value 5 100 VDC In DC Applications Recommended voltage ≤ 560 VDC Impedance Graph © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 4 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Environmental Test Data Test IEC Publication Procedure Endurance EN/IEC 60384–14 Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068–2–29 Test Eb 1,000 bumps at 390 m/s2 Change of Temperature IEC 60068–2–14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384–14 VR + 20 surge pulses at 2.5 kV (pulse every 5 seconds) Passive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 Needle flame test Damp Heat Steady State IEC 60068–2–78 Test Cab 1.25 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature +40°C and 93% RH, 56 days Approvals Mark Specification File Number EN/IEC 60384-14 V4413 UL 60384-14 and CAN/CSA E60384-14 (310VAC) E97797 Environmental Compliance All KEMET EMI capacitors are RoHS Compliant. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 5 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Table 1 – Ratings & Part Number Reference Capacitance Value (µF) Dimensions in mm B H L Lead Spacing (p) dV/dt (V/µs) New KEMET Part Number Legacy Part Number 0.010 0.015 0.022 0.033 0.047 0.068 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.15 0.15 0.22 0.22 0.22 0.22 0.33 0.33 0.33 0.47 0.15 0.22 0.33 0.47 0.68 1.0 5.0 5.0 5.0 5.0 6.0 6.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 9.0 7.5 8.5 6.0 9.0 7.5 10.0 7.5 13.0 11.0 6.0 6.0 7.0 10.0 11.0 13.0 11.0 11.0 11.0 11.0 12.0 12.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 17.5 12.5 13.5 14.5 17.5 12.5 18.5 16.0 18.5 12.0 19.0 15.0 15.0 16.0 18.5 20.0 22.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 500 500 500 500 500 500 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 200 200 200 200 200 200 46KF2100(1)H1(2) 46KF2150(1)H1(2) 46KF2220(1)H1(2) 46KF2330(1)H1(2) 46KF2470(1)H1(2) 46KF2680(1)H1(3) 46KI2100(1)H1(2) 46KI2150(1)H1(2) 46KI2220(1)H1(2) 46KI2330(1)H1(2) 46KI2470(1)H1(2) 46KI2680(1)H1(2) 46KI3100(1)H1(2) 46KI3150(1)H2(2) 46KI3150(1)H3(2) 46KI3150(1)H1(2) 46KI3220(1)H1(2) 46KI3220(1)H2(3) 46KI3220(1)H3(3) 46KI3220(1)H4(2) 46KI3330(1)H1(3) 46KI3330(1)H2(3) 46KI3330(1)H3(3) 46KI3470(1)H1(3) 46KN3150(1)H1(2) 46KN3220(1)H1(2) 46KN3330(1)H1(2) 46KN3470(1)H1(2) 46KN3680(1)H1(2) 46KN4100(1)H1(2) R46KF2100(1)H1(2) R46KF2150(1)H1(2) R46KF2220(1)H1(2) R46KF2330(1)H1(2) R46KF2470(1)H1(2) R46KF2680(1)H1(3) R46KI2100(1)H1(2) R46KI2150(1)H1(2) R46KI2220(1)H1(2) R46KI2330(1)H1(2) R46KI2470(1)H1(2) R46KI2680(1)H1(2) R46KI3100(1)H1(2) R46KI3150(1)H2(2) R46KI3150(1)H3(2) R46KI3150(1)H1(2) R46KI3220(1)H1(2) R46KI3220(1)H2(3) R46KI3220(1)H3(3) R46KI3220(1)H4(2) R46KI3330(1)H1(3) R46KI3330(1)H2(3) R46KI3330(1)H3(3) R46KI3470(1)H1(3) R46KN3150(1)H1(2) R46KN3220(1)H1(2) R46KN3330(1)H1(2) R46KN3470(1)H1(2) R46KN3680(1)H1(2) R46KN4100(1)H1(2) Capacitance Value (µF) B (mm) H (mm) L (mm) Lead Spacing (p) dV/dt (V/µs) New KEMET Part Number Legacy Part Number (1) Insert lead and packaging code. See Ordering Options Table for available options. (2) M = ±20%, K = ±10% (3) M = ±20% (only available tolerance). © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 6 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221ºC for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170ºC). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert throughhole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Manual Soldering Recommendations Wave Soldering Recommendations 300 Following is the recommendation for manual soldering with a soldering iron. 2+3s max 260°C 250 First wave Temperature (°C) Recommended Soldering Temperature Soldering iron bit temperature (deg C) 400 350 300 250 Second wave 200 Cooling ΔT <150°C Preheating 150 ca 2°C/s ca 3.5°C/s typical Tpreheat 100 ca 5°C/s 115°C max 100°C Typical 200 50 150 100 0 0 50 40 80 120 160 200 240 Time (s) 0 0 1 2 3 4 5 6 7 8 Soldering time (sec) The soldering iron tip temperature should be set at 350°C (+10°C maximum) with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 7 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Soldering Process cont'd Wave Soldering Recommendations cont'd 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch Pitch ≤ 10 mm = 15 mm > 15 mm ≤ 15 mm > 15 mm Polyester 130°C 130°C 130°C 270°C 270°C Polypropylene 100°C 110°C 130°C 260°C 270°C Paper 130°C 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 8 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Construction Single-sided Metallized Polypropylene Film (First Layer) Molded Plastic Case Detailed Cross Section Molded Plastic Case Self-Extinguishing Resin Single-sided Metallized Polypropylene Film (Second Layer) Margin Margin Metal Contact Layer Metal Contact Layer Margin FILM WINDING SCHEME OPTIONS Leads Single-sided Metallized Polypropylene Film Double-side Winding Scheme Single-sided Metallized Polypropylene Film 1 Section Single-sided Metallized Polypropylene Film Double-sided Metallized Polyester Carrier Film 2 Sections Single-sided Metallized Polypropylene Film 3 Sections 1 Section Single-sided Metallized Polypropylene Film 4 Sections © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Metallized Impregnated Paper Metallized Polyphenylene Sulfide Film (SMR) Polyprop Film Diel Double-sided Metallized Polyester Carrier Film Polyprop Film Diel 3 Sections F3006_R46_X2_275_125C • 5/13/2015 9 Poly Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Marking Lead Spacing 10 mm FRONT TOP Capacitance Tolerance Series, Dielectric Code, Safety Class, Self Healing Approval Marks Manufacturer’s Logo Capacitance, Rated Voltage IEC Climatic Category Date Code Passive Flammability Category Manufacturing Plant Lead Spacing 15 mm, 22.5 mm (small case sizes) FRONT TOP Capacitance Tolerance Series, Dielectric Code, Safety Class, Self Healing Approval Marks Manufacturer’s Logo Capacitance, Rated Voltage IEC Climatic Category Date Code Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 Manufacturing Plant Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm FRONT TOP Series Approval Marks Dielectric Code Safety Class Self Healing Manufacturer’s Logo Capacitance, Capacitance Tolerance, Rated Voltage IEC Climatic Category QA Number © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Passive Flammability Category F3006_R46_X2_275_125C • 5/13/2015 Date Code Manufacturing Plant 10 IEC Climatic Category Date Code Manufacturing Plant Metallized Polypropylene Film EMI Suppression Capacitors Passive Flammability Category: B for volume ≥ 1750 mm3 R46 Series, Class X2, 275 VAC, 125ºC C for volume < 1750 mm3 Marking cont'd Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm FRONT TOP Series Approval Marks Dielectric Code Safety Class Self Healing Manufacturer’s Logo Capacitance, Capacitance Tolerance, Rated Voltage IEC Climatic Category QA Number Passive Flammability Category Manufacturing Plant Date Code Manufacturing Date Code (IEC 60062) Y = Year, Z = Month Year Code Month Code 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 M N P R S T U V W X A B C D E F H J K L M January February March April May June July August September October November December 1 2 3 4 5 6 7 8 9 O N D © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 11 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Packaging Quantities Lead Spacing Thickness (mm) (mm) Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads Standard Reel ø 355 mm Large Reel ø 500 mm Ammo Taped 10 5 6 11 12 13 13 1300 1000 1500 1200 600 500 1250 1000 800 680 15 5 6 6 7.5 7.5 8.5 11 12 17.5 13.5 18.5 14.5 18 18 18 18 18 18 2000 1750 1000 1000 900 1000 1000 900 700 700 500 500 600 500 500 350 – 300 1250 1000 1000 800 800 700 800 680 680 500 500 440 9 10 11 13 12.5 16 19 12 18 18 18 18 1000 750 450 750 520 500 350 490 270 300 – 200 650 600 500 480 410 380 340 280 6 7 10 11 13 15 16 18.5 20 22 26.5 26.5 26.5 26.5 26.5 805 700 396 360 300 500 500 300 250 200 – – – – – 700 550 350 350 300 464 380 235 217 – 22.5 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 12 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Lead Taping & Packaging (IEC 60286–2) Figure 1 Lead Spacing 10 mm Figure 2 Lead Spacing 15 mm Figure 3 Lead Spacing 22.5 – 27.5 mm P W2 P2 P h h W W0 W1 H0 ød P1 P0 F D0 t P1 P2 Taping Specification Dimensions (mm) Description Symbol 10 Fig. 1 Lead Space 15 22.5 Fig. 2 Fig. 3 27.5 Fig. 3 Tol. Lead wire diameter d 0.6 0.6-0.8 0.8 0.8 ±0.05 Taping lead space P 25.4 25.4 38.1 38.1 ±1 Feedholeleadspace* P0 12.7 12.7 12.7 12.7 ±0.2** Centering of the lead wire P1 7.7 5.2 7.8 5.3 ±0.7 Centering of the body P2 12.7 12.7 19.05 19.05 ±1.3 Leadspacing(pitch)*** F 10 15 22.5 27.5 +0.6/-0.1 Component alignment ∆h 0 0 0 0 ±2 Height of component from tape center H 0**** 18.5 18.5 18.5 18.5 ±0.5 Carrier tape width W 18 18 18 18 +1/-0.5 Hold down tape width W0 9 10 10 10 Minimum Hole position W1 9 9 9 9 ±0.5 Hold down tape position W2 3 3 3 3 Maximum Feed hole diameter D0 4 4 4 4 ±0.2 t 0.7 0.7 0.7 0.7 ±0.2 Tape thickness * Also available in 15 mm. ** Max 1 mm on 20 lead spaces. *** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request. **** H0 = 16.5 mm available upon request. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 13 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Lead Taping & Packaging (IEC 60286–2) cont'd Ammo Specifications Dimensions (mm) H W T 360 340 59 H T W Reel Specifications Reel Size Standard Large Dimensions (mm) D H W 355 500 30 25 55 Maximum D H W © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 14 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC KEMET Corporation World Headquarters Europe Asia Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel: 389-2-55-14-623 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Harlow, United Kingdom Tel: 44-1279-460122 Taipei, Taiwan Tel: 886-2-27528585 Espoo, Finland Tel: 358-9-5406-5000 Southeast Asia Singapore Tel: 65-6701-8033 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 Central Novi, MI Tel: 248-306-9353 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 15 Metallized Polypropylene Film EMI Suppression Capacitors R46 Series, Class X2, 275 VAC, 125ºC Disclaimer Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3006_R46_X2_275_125C • 5/13/2015 16