DATASHEET Rev. A PSME10 SERIES 85~264VAC (125~373VDC) Input Voltage Range 10 Watts, Encapsulated PCB Mount Single Outputs, Isolation Class II Medical AC/DC Switching Power Supplies MEDICAL FEATURES • Isolation Class II • Universal Input Voltage: 85~264VAC or 125~373VDC • Fully Isolated Plastic Case • Green Design, No-Load Power Consumption < 0.3W • Single Outputs • All Using 105°C Long Life Electrolytic Capacitors • Cooling by Free Air Convection • -20°C ~ +70°C Wide Operating Temperature Range • RoHS Compliant • 100% Full Load Burn-in Tested • Energy Star Compliant • Short Circuit, Over Load, Over Voltage, and Brown-out (Low AC • Withstand 2G Vibration Test • 10 Watts Output Power Input Voltage) Protection • UL60601-1, TUV EN60601-1, and IEC60601-1 Medical Approvals DESCRIPTION The PSME10 series of Medical AC/DC switching power supplies provides 10 Watts of continuous output power in a 2.76” x 1.97” x 0.89” encapsulated PCB mountable package. This series consists of 5V, 12V, 15V, and 24VDC output models with a universal input voltage range of 85~264VAC or 125~373VDC. These power supplies are protected against short circuit, over load, over voltage, and brown-out (low AC input voltage) conditions and have an MTBF of 210,200 hours using MIL-HDBK-217F. This series also has UL60601-1, TUV EN60601-1, and IEC60601-1 medical approvals. All models have been 100% full load burn-in tested and are RoHS and Energy Star compliant. 02/06/2013 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 1 of 4 Rev. B PSME10 Series Single Outputs, Isolation Class II 10 Watts, Encapsulated PCB Mount Medical AC/DC Switching Power Supplies SPECIFICATIONS: PSME10 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT SPECIFICATIONS Input Voltage Range TEST CONDITIONS AC Input Voltage Range DC Input Voltage Range Low Line High Line Low Line Inrush Current High Line No Load Power Consumption OUTPUT SPECIFICATIONS Output Voltage Voltage Tolerance Load Regulation Line Regulation Nom 85 125 47 Input Frequency Input Current Min Full Load, Vin = 115VAC Full Load, Vin = 230VAC Cold Start, Vin = 115VAC Cold Start, Vin = 230VAC Max Unit 264 373 63 VAC VDC Hz 0.25 0.15 25 45 A A 0.3 5VDC output model 12V, 15V, & 24VDC output models 5VDC output model 12V, 15V, & 24VDC output models 10% to 100% rated load Low Line to High Line at rated load -3 -1 -0.5 -1 -0.5 0 See Table +5 +1 +0.5 +1 +0.5 10 See Table See Table 25 100 100 25 +0.03 W % % % Output Power W Output Current Ripple & Noise (See Note 1) Low Line Full Load, Vin = 115VAC Hold-Up Time ms High Line Full Load, Vin = 230VAC Setup Time (See Note 3) Full Load, Vin = 115/230VAC ms Rise Time Full Load, Vin = 115/230VAC ms Temperature Coefficient 0~50°C -0.03 %/°C PROTECTION Over Voltage Protection Latch-off mode 115 145 % Over Load Protection Hiccup mode, recovers automatically after fault condition is removed 110 % Short Circuit yes Brown-out (Low AC Input Voltage) yes GENERAL SPECIFICATIONS Efficiency Vin = 230VAC See Table Withstand Voltage (Input to Output) 4000 VAC Isolation Resistance (Input to Output) 500VDC 100 MΩ ENVIRONMENTAL SPECIFICATIONS Operating Temperature With derating (see derating curve) -20 +70 °C Storage Temperature -40 +85 °C Operating Humidity Non-condensing 20 90 % RH Storage Humidity 10 95 % RH Vibration 10~500Hz, 2G 10min/1cycle, period for 60 min each along X, Y, and Z axes Cooling Free air convection MTBF MIL-HDBK-217F 210,200 hours PHYSICAL SPECIFICATIONS Weight Approximately 3.7oz (105g) Dimensions (L x W x H) 2.76 x 1.97 x 0.89 inches (70 x 50 x 22.7 mm) SAFETY & EMC Safety Approvals UL60601-1, TUV EN60601-1, and IEC60601-1 EMI Conduction & Radiation EN55011: 2007+A2: 2007 Class B Harmonic Current EN61000-3-2: 2006 Class A, EN61000-3-3: 1995+A1: 2001+A2: 2005 EMS Immunity EN60601-1-2: 2001+A1: 2006, IEC61000-4-2,3,4,5,6,8,11 light industry level, criteria A 02/06/2013 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 2 of 4 PSME10 Series Single Outputs, Isolation Class II 10 Watts, Encapsulated PCB Mount Medical AC/DC Switching Power Supplies Rev. B MODEL SELECTION TABLE Model Number Input Voltage Range Output Voltage Output Current Ripple & Noise (1) Efficiency Output Power 5 VDC 2A 80mVp-p 77% 10W 12 VDC 0.83A 150mVp-p 79% 10W 15 VDC 0.66A 150mVp-p 80% 10W 24 VDC 0.42A 240mVp-p 82% 10W PSME-10-05 85 ~ 264 VAC or 125 ~ 373 VDC PSME-10-12 PSME-10-15 PSME-10-24 NOTES 1. Ripple & noise is measured at 20MHz bandwidth by using 12" twisted pair-wire terminated with 0.1µF and 47µF capacitors in parallel. 2. Tolerance includes set up tolerance, line regulation, and load regulation. 3. The length of the setup time is measured a first cold start. Turning the power supply ON and OFF very quickly may lead to an increase in the setup time. 4. The power supply is considered a component which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives. BLOCK DIAGRAM RECTIFIERS & FILTER EMI FILTER I/P RECTIFIERS & FILTER POWER SWITCHING PWM CONTROL +V -V DETECTION CIRCUIT DERATING CURVE Load vs Input Voltage Load vs Temperature Ta=25°C 100 100 90 Load (%) Load (%) 80 60 80 70 60 40 50 20 40 -20 0 10 20 30 40 50 60 70 85 100 Ambient Temperature (°C) 02/06/2013 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 110 120 264 Input Voltage (VAC) Page 3 of 4 PSME10 Series Single Outputs, Isolation Class II 10 Watts, Encapsulated PCB Mount Medical AC/DC Switching Power Supplies Rev. B MECHANICAL DRAWING Unit: inches (mm) 2.76 (70) 0.315 (8) BOTTOM VIEW AC/N +V AC/L 0.041 (1.05) 0.89 (22.7) 0.138 (3.5) 1.97 (50) -V 0.295 (7.5) 0.689 (17.5) 0.59 (15) 0.789 (20.04) 2.13 (54) COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 02/06/2013 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 5 Watson Brook Rd. Exeter, NH 03833 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 4 of 4