DATA SHEET SKY65364-21: 900 MHz Transmit/Receive Front-End Module Applications Automated meter reading Advanced metering infrastructure Digital Control 3 Control Logic VPC ISM systems PA Range extender Matching Network Harmonic Filter Features TX ANT Transmit output power > +30 dBm Harmonic Filter Matching Network High-efficiency PA Matching Network LNA RXO Bias Analog power control RX1 Receive path NF <2.1 dB PA bypass mode RX2 RBIAS 203189E-001 Figure 1. SKY65364-21 Functional Block Diagram LNA low-current mode with external resistor LNA bypass mode Description Integrated control logic The Skyworks SKY65364-21 is a high-performance, transmit/receive (T/R) front-end module (FEM). The device provides a complete T/R chain with T/R switches. Internal RF match and bias circuits All RF ports internally DC blocked Shutdown mode Small footprint, MCM (28-pin, 6 x 6 mm) package (MSL3, 260 C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. The device transmit chain features +30 dBm output power and a 40 percent power-added efficiency (PAE). The device receive chain features a low-noise amplifier (LNA) with a 1.5 dB noise figure (NF) and 15 dB gain. The cascaded NF and gain, taking into account the 0.5 dB insertion loss transmit/receive antenna switch, are 2.1 dB and 14.5 dB, respectively, which makes the SKY65364-21 ideal for medium power microwave links such as 900 MHz Industrial, Scientific, and Medical (ISM) band applications. The module also has a shutdown mode, PA bypass mode, and LNA bypass mode to minimize power consumption. The device is mounted in a 28-pin, 6 x 6 mm Multi-Chip Module (MCM) surface-mount technology (SMT) package, which allows for a highly manufacturable low-cost solution. A functional block diagram of the SKY65364-21 is shown in Figure 1. The device package and pinout for the 28-pin MCM are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 1 GND VCC_TX3 VCC_TX2 VCC_TX1 VDD2 27 26 25 24 23 21 GND EN 3 20 TX BYP 4 19 GND VPC 5 18 RXO GND 6 17 VCC_RX ANT 7 16 VDD1 GND 8 15 GND 9 10 11 12 13 14 RBIAS 2 RX2 GND GND 22 GND TR 28 RX1 1 GND GND GND DATA SHEET • SKY65364-21: T/R FRONT-END MODULE 203189E-002 Figure 2. Figure 1. SKY65364-21 Pinout (Top View) Table 1. SKY65364-21 Signal Descriptions Pin Name Description Pin Name Description 1 GND Ground 15 GND Ground 2 TR Digital control input: transmit/receive mode 16 VDD1 3.3 V power supply 3 EN Digital control input: shutdown mode 17 VCC_RX 3.3 V power supply 4 BYP Digital control input: bypass mode 18 RXO Receive output 5 VPC Transmit output power adjustment 19 GND Ground 6 GND Ground 20 TX Transmit path input port. Internally matched to 50 Ω. 7 ANT Antenna switch common port. Internally matched to 50 Ω. 21 GND Ground 8 GND Ground 22 GND Ground 9 GND Ground 23 VDD2 3.6 V power supply 10 RX1 Receive arm of antenna switch. Internally matched to 50 Ω. 24 VCC_TX1 3.6 V power supply 11 GND Ground 25 VCC_TX2 3.6 V power supply 12 GND Ground 26 VCC_TX3 3.6 V power supply 13 RX2 LNA and bypass switch output port. Internally matched to 50 Ω. 27 GND Ground 14 RBIAS LNA bias setting resistor 28 GND Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Technical Description Receive Path The SKY65364-21 consists of a complete T/R chain with T/R switches contained in the module. A single-pole, triple-throw (SP3T) switch selects between the receive, transmit, and transmit bypass paths. The module has a shut-down mode to minimize power consumption. The receive path contains an LNA with bypass switch. The LNA impedance matching networks are internal to the module and have been optimized for a low NF while maintaining good return losses into a 50 Ω source and load impedance. The receive arm of the SP3T switch and the LNA input are connected to module pins to allow an external filter to be inserted into the receive path. Three digital input pins (EN, TR, and BYP) are used to select between transmit, transmit bypass, receive, receive bypass, or shutdown mode. Transmit Path The transmit path contains a Power Amplifier (PA) optimized for saturated performance. The PA output is internally matched for optimum output power and efficiency into a 50 Ω load impedance. The PA output is passed through an harmonic filter before being fed through the SP3T switch. The PA input provides a good return loss into a 50 Ω source impedance. Transmit output power is controlled by the VPC pin, which is normally set to 2.25 V DC voltage. The nominal DC input impedance into the VPC pin is 50 kΩ. Operation Mode Control The five SKY65364-21 operating modes are controlled by the three digital pins TR, EN, and BYP (pins 2, 3, and 4, respectively). The control logic truth is provided in Table 2. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY65364-21 are provided in Table 3. Recommended operating conditions are specified in Table 4. Electrical specifications are provided in Tables 5, 6, and 7. Table 2. SKY65364-21 Operating Modes Truth Table1 Control Voltage Internal States TR (Pin 2) EN (Pin 3) BYP (Pin 4) PA LNA LNA Bypass Switch T/R Switch PA Bypass Switch Transmit 1 1 0 On Off Open PA PA Transmit bypass 1 1 1 Off Off Open PA bypass PA bypass Receive 0 1 0 Off On Open RX1 Open Receive Bypass 0 1 1 Off Off Through RX1 Open Shutdown2 X 0 X Off Off Open Open Open Operating Mode 1 See Table 4 for logic 0 and 1 characteristics. “X” = don’t care state, defined as a valid state of logic 1 or 0. 2 In the high state, EN, TR, and BYP have an input current of 33 μA due to an internal 100 kΩ pulldown resistance. For the lowest leakage current, the high state is not recommended for TR and BYP when the device is in shutdown mode (EN = 0). Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 3 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Table 3. SKY65364-21 Absolute Maximum Ratings1 Parameter Symbol Minimum Maximum Units –0.3 +5.0 V 20 mA –0.3 +6.0 V 1.6 A LNA supply voltage VCC_RX LNA supply current ICC_RX PA supply voltage VCC_TX1/2/3 PA supply current ICC_TX Digital supply voltage VDD1 –0.5 +5.5 V Digital supply voltage VDD2 –0.5 +5.5 V Digital control voltage (EN, TR, BYP) VCTL –0.5 VDD1 + 0.3 V Transmit output power control voltage VPC –0.3 +5.0 V Receive RF input power (RX2) PIN_RX2 +5 dBm Receive bypass RF input power (RX2) PIN_RX2_BYP +18 dBm Receive RF input power (ANT) PIN_ANT +33 dBm Transmit RF input power PIN_TX +15 dBm +20 dBm +85 °C Transmit RF input power, bypass mode PIN_TX_BYP Operating case temperature (Note 2) TC –40 Storage temperature TSTG –55 +150 °C Junction temperature TJ +150 °C T/R port load VSWR in transmit mode VSWR 10:1 – 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. 2 Nominal thermal resistance, junction to case, is 18 °C/W. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industrystandard ESD handling precautions should be used at all times. Table 4. SKY65364-21 Recommended Operating Conditions Parameter Symbol Minimum Transmit frequency range f Receive frequency range f 900 LNA supply voltage VCC_RX 3.00 Digital supply voltage VDD1 VDD2 PA supply voltage Digital input voltage, logic 1 (EN, TR, BYP) Digital input voltage, logic 0 (EN, TR, BYP) Typical 890 Maximum Units 960 MHz 960 MHz 3.30 3.45 V 3.00 VCC_RX VCC_RX V 3.40 VCC_TX1/2/3 3.80 V VCC_TX1/2/3 3.40 3.60 3.80 V VIH 2.8 VDD1 V VIL 0 0.7 V Transmit output power control voltage VPC 0 Receive RF input power (RX2) PIN_RX2 Transmit RF input power (TX) PIN_TX Transmit duty cycle 2.25 +12 2.50 V –15 dBm +13 dBm 50 % Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Table 5. SKY65364-21 DC Electrical Specifications1 (VCC_RX = VDD1 = 3.3 V, VCC_TX1/2/3 = VDD2 = 3.6 V, TC = 25 C, RBIAS = 0 Ω, No RF Input Power, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Quiescent current, receive mode2 IQ_RX 12 mA Quiescent current, receive bypass mode2 IQ_BYP 80 μA VDD1 quiescent current, transmit mode IQ_VDD1 22 VCC_TX1/2/3 quiescent current, transmit mode IQ_TX TC = 25 °C, VCC_TX1/2/3 = 3.6 V, VCC_RX = 3.3 V 18 VCC_TX1/2/3 operating current, transmit mode IOP_TX PIN = +12 dBm 680 VDD1 quiescent current, transmit bypass mode3 IDD1 VCC_TX1/2/3 quiescent current, transmit bypass mode3 IQ_TXB VCC_RX quiescent current, shutdown mode3 VCC_TX1/2/3 quiescent current, shudown mode3 Digital input current, logic 13 Digital input current, logic 03 30 mA mA 750 mA 50 μA 4 μA IQ_SD_RX 0.5 μA IQ_SD_TX 0.005 μA IIH 33 μA IIL 0 μA 1 Performance is guaranteed only under the conditions listed in this table. Modes are established as indicated in Table 2. 2 Total current drawn from VCC_RX and VDD1 supplies. 3 Not production tested. Table 6. SKY65364-21 Electrical Specifications: Receive and Receive Bypass Mode1 (1 of 2) (VCC_RX = VDD1 = 3.3 V, VCC_TX1/2/3 = VDD2 = 3.6 V, TC = 25 C, f = 900 to 960 MHz, 50 Ω Source and Load Impedance, CW Input, RBIAS = 0 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Receive Mode: RX2 to Receive Output Path Small signal gain G Noise figure NF 15 TC = 25 °C, VCC_RX = 3.3 V 1.5 dB 2.1 dB Noise figure variation over temperature NFTEMP 1 dB input compression point (Note 2) IP1dB 1 dB gain compression ±0.15 dB –10 dBm Third order input intercept point (Note 2) IIP3 PIN = –30 dBm/tone, 200 kHz spacing Input return loss |S11| –3 0 dBm 12 15 dB Output return loss |S22| 8 Reverse isolation |S12| 12 dB 20 dB Transition time (Note 2) t 0.5 μs Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 5 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Table 6. SKY65364-21 Electrical Specifications: Receive and Receive Bypass Mode1 (2 of 2) (VCC_RX = VDD1 = 3.3 V, VCC_TX1/2/3 = VDD2 = 3.6 V, TC = 25 C, f = 900 to 960 MHz, 50 Ω Source and Load Impedance, CW Input, RBIAS = 0 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max 3 5 Units Receive Bypass Mode: RX2 to Receive Output Path Insertion loss IL 1 dB input compression point2 IP1dB 1 dB gain compression Third order input intercept point2 IIP3 PIN = 0 dBm/tone, 200 kHz spacing Input return loss +15 |S11| 10 Output return loss |S22| 10 Transition time2 t dB dBm +27 dBm 18 dB 18 dB 0.5 μs Receive and Receive Bypass Mode: ANT to RX1 Path Insertion loss IL 0.5 1 dB input compression point2 IP1dBANT 1 dB gain compression Third order input intercept point2 IIP3ANT PIN = +10 dBm/tone, 200 kHz spacing Input return loss |S11| 14 Output return loss |S22| 14 Transition time2 t +24 1.0 +30 dBm +47 dBm 19 dB 19 dB 3.0 μs 1 Performance is guaranteed only under the conditions listed in this table. Modes are established as indicated in Table 2. 2 Not production tested. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 dB May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Table 7. SKY65364-21 Electrical Specifications: Transmit Mode1 (VCC_RX = VDD1 = 3.3 V, VCC_TX1/2/3 = VDD2 = 3.6 V, PIN = +12 dBm, VPC = 2.25 V, TC = 25 C, f = 890 to 960 MHz, 50 Ω Source and Load Impedance, CW Input, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units TX to ANT Path Output power2 +30 dBm Output power variation over supply voltage POUT TC = 25 °C TC = 25 °C, VCC_TX1/2/3 = 3.6 V +29.5 ±0.4 dB Output power variation over temperature VCC_TX1/2/3 = 3.6 V ±0.3 dB Output power control PCTL VPC = 0 V to 2.25 V3 Small signal transmit PA gain4 GTX PRF input @ –30 dBm Power-added efficiency PAE 2nd harmonic 2fo –50 dBc 3rd to 10th harmonic5 3fo to 10fo –50 dBc Input return loss |S11| 10 dB Output return loss |S22| 8 dB Non-harmonic spurious4 PSPUR Power on time4 t 4.4 Insertion loss IL 1.5 1 dB input compression point4 IP1dB Third order input intercept point4 IIP3 PIN = +10 dBm/tone, 200 kHz spacing +47 2nd harmonic 2fo PIN = +12 dBm –90 –40 dBc –90 –40 dBc 40 47 dB 16 dB 40 VSWR 10:1, all phases % –50 dBm μs TX to ANT Path, Transmit Bypass Mode rd +24 2.5 +30 dB dBm dBm 3 harmonic 3fo PIN = +12 dBm Transmit bypass path rejection R2FO @ 2fo (1780 MHz to 1920 MHz) 27 36 dB R3FO @ 3fo (2670 MHz to 2880 MHz) 32 36 dB 10 dB Input return loss |S11| Output return loss |S22| 10 dB Transition time4 t 3.4 μs ANT to RX1 Path Isolation |S21| 25 35 dB |S21| 25 35 dB ANT to RX1 Path, Transmit Bypass Mode Isolation 1 Performance is guaranteed only under the conditions listed in this table. Modes are established as indicated in Table 2. 2 Output power rated at the antenna output. PA output power is actually 1.5 dB higher or +32 dBm for a POUT of +30.5 dBm. 3 Output power control is the difference between the output power at VPC = 2.25 V and VPC = 0 V. 4 Not production tested. 5 Only the 2nd to 5th harmonics have been production tested. The 6th to 10th harmonics are characterized only. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 7 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Evaluation Board Description Package and Handling Information The SKY65364-21 Evaluation Board is used to test the performance of the SKY65364-21 T/R FEM. A typical application schematic diagram is provided in Figure 3. An Evaluation Board schematic diagram is provided in Figure 4. An assembly drawing for the Evaluation Board is shown in Figure 5, and the layer detail is provided in Figure 6. Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY65364-21 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Package Dimensions The footprint drawing and package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 3.6 V 220 pF 6 4.7 nF 1 μF 7 8 VDD2 VCC_TX1 VCC_TX2 GND EN GND GND TX BYP GND VPC RXO GND VCC_RX ANT VDD1 GND 9 10 11 12 13 1 μF 23 RBIAS 5 24 RX2 Receive Bypass Mode Digital Input Transmit Output Power Adjust 25 GND 4 TR VCC_TX3 3 26 GND Shutdown Mode Digital Input 27 RX1 2 GND GND 1 GND 28 Transmit/Receive Digital Input 1 nF GND 22 21 50 Ω Line 20 Transmit Input 19 50 Ω Line 18 Receive Output 17 3.3 V 16 220 pF 1 uF 15 14 0Ω Antenna 50 Ω Line Antenna Switch Receive LNA and Bypass Switch Output 50 Ω Line 203189E-003 Figure 3. SKY65364-21 Typical Application Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE 14 13 12 11 10 9 8 7 6 5 4 3 2 VCC_RX GND GND VCC_TX1_SENSE VCC_TX1 GND GND VCC_TX23 VCC_TX23_SENSE GND TR EN BYP VPC DCH1 Header 1 C28 10 μF C27 220 μF R8 DNI C12 10 μF C1 DNI C7 10 nF C2 4.7 nF C8 4.7 nF L3 0Ω L4 0Ω C24 DNI C26 1 μF Antenna 6 L5 0Ω J1 50 Ω Line 7 8 C19 DNI Antenna Switch Receive J2 C25 DNI N/C VCC_TX1 VCC_TX2 23 GND GND EN TX N/C GND VPC RX GND N/C ANT VDD1 GND C20 DNI 9 10 11 12 13 N/C 5 TR 24 N/C R9 0Ω 25 GND 4 26 GND 3 GND GND 2 27 GND 28 1 C10 DNI VCC_TX3 C22 DNI R10 DNI C15 DNI C5 220 pF C23 DNI C21 DNI C16 DNI C11 1 μF GND L2 0Ω C17 DNI C6 1 nF C9 4.7 nF N/C L1 0Ω C18 DNI R7 0Ω GND 22 21 Transmit Input 19 J4 50 Ω Line 18 Receive Output 17 16 C3 220 pF C4 1 uF 15 R5 0Ω 14 50 Ω Line J5 50 Ω Line 20 50 Ω Line J3 LNA and Bypass Switch Output Notes: Some component labels may be different from the corresponding component symbol shown here. Component values, however, are accurate as of the date of this data sheet. PCB Recommendations: Metal Layer 1 = RF traces + control lines. Core thickness between top RF layer and ground plane is critical. Metal Layer 2 = Solid ground plane. No traces routing. Metal Layer 3 and 4 = Control lines + VCC traces (no VCC plane). Pour copper on each layer connected to the ground plane. Use VCC traces in a star distribution pattern. Always use 4 layers. 203189E-004 Figure 4. SKY65364-21 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 9 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE 203189E-005 Figure 5. SKY65364-21 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Layer 1: Top – Metal Layer 3: Ground Layer 2: Ground Layer 4: Solid Ground Plane 203189E-006 Figure 6. SKY65364-21 Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 11 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE 0.5 0.4 0.05 0.05 0.15 Stencil aperture size for center ground pads should be 80% to 100% (by area) of the solder mask opening of the package. 6.3 0.8 0.9 Stencil and Metallization 8X 0.062 Package Outline Solder Mask Opening 6.3 16X 0.875 SMT Pad Detail Scale: 2X 6X This Rotation 6X Rotated 180° 6X Rotated 90° CW 6X Rotated 90° CCW Package Outline 8X 0.063 16X 0.875 Stencil Aperture Top View 6.4 3.875 0.9 0.8 0.05 0.05 0.15 0.85 0.75 Package Outline 6.4 3.875 Stencil and Metallization Package Outline Solder Mask Opening SMT Pad Detail Scale: 2X 1X This Rotation 1X Rotated 180° Solder Mask Opening Top View (6.3) (1.5) Pin 28 0.25 Typ. Pin 1 The cross-hatched area represents the merger of the center ground pad +12 individual I/O ground pads. All I/O ground pads should have at least one via connected to internal ground planes for optimum electrical performance. 0.9 0.8 Package Outline (10X 0.75 Pitch) (6.3) 0 4X 0.375 (1.2) 0.05 0.05 0.75 0.85 0.15 4X 1.125 4X 1.875 Stencil and Metallization 2X 2.750 Package Outline Solder Mask Opening Metallization Top View 2X 2.750 4X 1.813 4X 1.088 0 4X 0.363 (10X 0.725 Pitch) Thermal Via Array. ∅0.3 mm on 0.6 mm pitch. Additional vias in common ground pad will improve thermal and electrical performance. NOTE: thermal vias should be tented and filled with solder mask, 30-35 μm Cu plating recommended. SMT Pad Detail Scale: 2X 1X This Rotation 1X Rotated 180° 203189E-007 All measurements are in millimeters Figure 7. SKY65364-21 Footprint Drawing and Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F DATA SHEET • SKY65364-21: T/R FRONT-END MODULE ∅1.50 ± 0.10 0.25 ± 0.02 (T) 4.00 ± 0.10 2.00 ± 0.10 1.75 ± 0.10 6.35 ± 0.10 (Bo) A A B 1.30 ± 0.10 (Ko) 12.00 ± 0.20 B 5.50 ± 0.10 Pin 1 Indicator ∅1.55 ± 0.05 8.00 ± 0.10 B 6.35 ± 0.10 (Ao) Notes: 1. 2. 3. 4. 5. Carrier tape: black conductive polycarbonate or polystyrene. Cover tape material: transparent conductive PSA. Cover tape size: 9.3 mm width. All dimensions are in millimeters. ESD-surface resistivity is ≤1 x 1010 Ohms/square per EIA, JEDEC TNR Specification. A 203189E-008 Figure 8. SKY65364-21 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203189F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 24, 2016 13 DATA SHEET • SKY65364-21: T/R FRONT-END MODULE Ordering Information Model Name SKY65364-21: T/R Front-End Module Manufacturing Part Number SKY65364-21 Evaluation Board Part Number SKY65364-21-EK1 Copyright © 2012, 2014-2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 May 24, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203189F