LTR A B C D E F G H REVISIONS DESCRIPTION Page 5 - Paragraph 3.4.y, changed insulation resistance requirements. Page 6 - TABLE I, changed measurement frequencies for insertion loss at -55°C and +125°C. Page 7 - Paragraph 6.4, changed vendor style numbers. Pages 3 and 4 - Dimensional changes. Page 5 - Paragraph 3.7, changed manufacturer eligibility requirement. Page 6 - TABLE I, changed insertion loss limits on several dash numbers. Changed dc resistance and voltage drops on -017 through -019. Page 8 - Added another suggested source of supply. Added suggested source of supply. Editorial changes throughout. Page 2 - Changed PIN to include case finish option. Paragraph 3.1.3, added case finish options; prohibited use of pure tin as a case finish. Page 7 - Added paragraph to explain prohibition of pure tin; added supersession table. Editorial changes throughout. Editorial changes throughout. Removed a source of supply. Editorial changes throughout. Editorial changes throughout DATE APPROVED 9 Jan 85 Ivan R. Jones 25 Aug 87 David E. Moore 4 Jun 90 14 Nov 91 David E. Moore David E. Moore 2 May 94 David E. Moore 22 Aug 2000 14 Sep 2005 2 Dec 2010 K. A. Cottongim K. A. Cottongim M. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES Source control drawing REV H H H H H H H H H PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH Original date of drawing CHECKED BY 11 Sep 84 David E. Moore TITLE FILTERS AND CAPACITORS, RADIO FREQUENCY/ ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED APPROVED BY Randy Larson SIZE A REV AMSC N/A CODE IDENT. NO. DWG NO. 14933 H 84083 PAGE 1 OF 9 59GP-2011-E04 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-28861 describe the requirements for radio frequency/electromagnetic interference suppression, hermetically sealed filters and capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 84083 | | | Drawing number XXX | | | Dash number (see table I) * | | | Case finish (see 3.1.3) (NOTE: The PIN has been revised with revision E of this drawing to include a case finish option (see 3.1.3). For supersession data, see 6.7). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.3). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-28861 - Filters and Capacitors, Radio Frequency/Electromagnetic Interference Suppression, General Specification for DEPARTMENT OF DEFENSE STANDARDS MIL-STD-220 - Method of Insertion Loss Measurement. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise stated herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28861 and herein. 3.1.1 Terminals. Terminals shall be solderable and in accordance with figure 1. 3.1.2 Case dimensions. The case dimensions shall be in accordance with figure 1. 3.1.3 Finish. The case and lead finish shall be T (tin-lead plated), S (silver plated), or G (gold plated), in accordance with MIL-PRF-28861. (NOTE: Pure tin finish is prohibited after 4 November 1994 (see 6.2). Pure tin is prohibited as specified in MIL-PRF-28861. Finish T, tin-lead plating, shall have a minimum lead content of 3 percent.) DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 2 MOUNTING HARDWARE CIRCUIT DIAGRAMS FIGURE 1. Case and hardware dimensions and circuit diagrams. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 3 PIN 84083- L dimension max Weight (grams) maximum 001* 002* 003* 004* 005* 006* 007* 008* 009* 010* 011* 012* 013* 014* 015* 016* 017* 018* 019* .700 1.060 " " " " " " " " " 1.205 " " " " 1.400 " " 18.0 20.0 " " " " " " " " " 29.0 " " " " " " " Inches .005 .007 .010 .015 .020 .022 .062 .093 mm 0.12 0.17 0.25 0.38 0.50 0.55 1.57 2.36 Inches .120 .125 .250 .290 .312 .3125 .375 .420 mm 3.04 3.17 6.35 7.36 7.92 7.93 9.52 10.66 Inches .440 .620 .690 .700 1.060 1.205 1.400 mm 11.17 15.74 17.52 17.78 26.92 30.60 35.56 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagram is for information only. 4. All filters shall be supplied with mounting hardware (hex nut and lockwasher). Mounting hardware shall be furnished with the same finish as the filter case. 5. Terminal identification (non-symmetrical filters): The case shall be marked at the threaded end of the filter, with the symbol "C" or the symbol "L", as follows, or the circuit diagram shall be marked on the case. Circuit L1 - - - - - - - L2 - - - - - - - - Symbol C L 6. Imperfect thread or undercut optional .062 inch (1.57 mm) maximum. 7. One imperfect thread allowed .035 inch (0.89 mm) maximum. 8. Recommended mounting torque: 60 ounce-inches ± 4 ounce-inch. FIGURE 1. Case and hardware dimensions and circuit diagrams - Continued. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 4 3.1.4 Weight. The maximum weight shall be as specified on figure 1. 3.2 Operating temperature range. The operating temperature range shall be -55°C to +125°C. 3.3 Temperature rise. The temperature rise shall be +25°C maximum. 3.4 Electrical characteristics. 3.4.1 Rated voltage. The rated voltage shall be +125 volts ac at maximum rated frequency and 300 volts dc. 3.4.2 Rated current. The rated current shall be in accordance with table I. 3.4.3 Rated frequency. The rated frequency shall be dc to 400 Hz. 3.4.4 Insertion loss. The insertion loss shall be in accordance with table I. 3.4.5 Voltage and temperature limits of capacitance. +15, -40 percent. 3.4.6 DC resistance. The dc resistance shall be in accordance with table I. 3.4.7 Insulation resistance. a. At +25°C: 1,000 megohms minimum. b. At +125°C: 100 megohms minimum. 3.4.8 Voltage drop. The voltage drop shall be as specified in table I. 3.4.9 Capacitance to ground. Capacitance to ground shall be as specified in table I. 3.5 Environmental and mechanical requirements. The environmental and mechanical requirements shall be in accordance with MIL-PRF-28861 for class B, hermetically sealed filters. 3.6 Product assurance level. Level B only. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285 except the PIN shall be as specified in 1.2 with the manufacturer's name or code, date code, voltage rating, current rating, and terminal identification. 3.8 Manufacturer eligibility. To be eligible for listing as a suggested source of supply, a manufacturer shall be listed on the MIL-PRF-28861 Qualified Products List for at least one part or, perform first article inspection in accordance with the MIL-PRF-28861 qualification inspection requirements for class B. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.11 Workmanship. Filters and capacitors shall be processed in such a manner as to be uniform in quality and shall be free from cold soldering, corrosion, pits, dents, cracks, rough sharp edges, misalignments, and other defects that will affect life, serviceability, or appearance. Cracks in glass seals are not allowed, however, minor meniscus crazing is acceptable. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 5 TABLE I. Electrical characteristics. PIN 84083- Circuit Maximum rated current (A) Capacitance -0, +100 percent (µF) 15 Maximum voltage drop MaxMinimum insertion loss (dB) in accordance with MIL-STD-220 1/ 2/ imum dc At +25°C At -55°C and +125°C resistance 50 100 150 300 1 10 100 1 50 100 150 300 1 10 100 1 (ohms) kHz kHz kHz kHz MH MH MH GHz kHz kHz kHz kHz MHz MHz MHz GHz z z z (volts ac rms) (volts dc) .30 .14 .12 .008 7 13 16 22 32 46 58 70 5 11 14 20 30 44 56 70 0.5 .30 .47 .165 .33 13 23 28 40 60 60 70 70 11 21 26 38 58 58 70 70 1.0 .30 .47 .15 .15 6 18 24 37 56 60 70 70 4 16 22 35 54 58 70 70 3.0 .30 .32 .078 .026 7 13 17 24 42 70 70 70 5 11 15 22 40 70 70 70 5.0 .30 .21 .065 .013 7 13 16 22 34 68 70 70 5 11 14 20 32 66 70 70 10.0 .30 .12 .08 .008 7 13 16 20 30 56 70 70 5 11 14 18 28 54 70 70 001* C 002* L1 003* L2 004* L1 005* L2 006* L1 007* L2 008* L1 009* L2 010* L1 011* L2 012* Pi 0.5 .36 .47 .165 .33 14 34 44 62 80 80 80 80 12 32 42 60 80 80 80 80 013* Pi 1.0 .36 .47 .15 .15 --- 26 37 56 80 80 80 80 --- 24 35 54 80 80 80 80 014* Pi 3.0 .36 .32 .078 .026 --- --- 18 40 70 80 80 80 --- --- 16 38 68 80 80 80 015* Pi 5.0 .36 .21 .065 .013 --- --- --- 25 60 80 80 80 --- --- --- 23 58 80 80 80 016* Pi 10.0 .36 .12 .08 .008 --- --- --- --- 50 80 80 80 --- --- --- --- 48 80 80 80 017* T 1.0 .30 .22 .07 .07 6 13 18 28 58 70 70 70 4 11 16 26 56 70 70 70 018* T 2.0 .30 .32 .10 .05 6 12 16 22 37 70 70 70 4 10 14 20 35 70 70 70 019* T 4.0 .30 .22 .12 .03 6 12 16 20 34 70 70 70 4 10 14 18 32 70 70 70 1/ Insertion loss measurements shall be made under full load over the frequency range of 100 kHz to 10 MHz. Insertion loss measurements above and below this frequency range shall be under no load. 2/ The insertion loss requirements between any two adjacent specified frequencies shall be that of the lower of the two frequencies in order to accommodate resonant dips. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 6 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of MIL-PRF-28861. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certification of compliance with group B requirements in lieu of performing group B tests (see 6.3c). 5. PACKAGING 5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activity within the Military Department or Defense Agency, or within the military services’ system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Filters conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28861, this drawing becomes obsolete and will not be used for new design. The QPL-28861 product shall be the preferred item for all applications. 6.2 Tin plated finish. Pure tin is prohibited since it may result in tin whisker growth. The use of alloys with tin content greater than 97 percent may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coating of Tin). 6.3 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. d. Requirements for notification of change of product to acquiring activity, if applicable. e. Requirements for packaging and packing (see 5.1). 6.4 Replaceability. Filters covered by this drawing will replace the same commercial device covered by contractor-prepared specification or drawing. 6.5 Cataloging information. Dash number 001* shall be cataloged under FSC 5910 as a feed-through ceramic capacitor. Dash numbers 002* through 019* shall be cataloged under FSC 5915 as radio frequency interference filters. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 7 6.6 Users of record. Military and industry users of his drawing should inform DLA Land and Maritime when a system application requires configuration control. DLA Land and Maritime-VA will maintain a record of users and this list will be used for coordination and distribution of changes to this drawing. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, PO Box 3990, Columbus, OH 43218-3990, by e-mail to [email protected], or by telephone (614) 692-4709. 6.7 Supersession data. Table II provides a list of supersession data from previous revisions to the superseding PIN of revision E and later. The superseding PIN indicates only the "T" case finish since that was the only case finish available prior to revision E. TABLE II. Supersession data. Superseded PIN 84083001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 Superseding PIN 84083001T 002T 003T 004T 005T 006T 007T 008T 009T 010T 011T 012T 013T 014T 015T 016T 017T 018T 019T DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 8 6.8 Approved sources of supply. The approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime-VAT, PO Box 3990, Columbus, OH 43218-3990, by e-mail to [email protected], or by telephone (614) 692-4709. DSCC drawing 84083- 1/ Vendor CAGE number 001* 002* 003* 004* 005* 006* 007* 008* 009* 010* 011* 012* 013* 014* 015* 016* 017* 018* 019* 33095 " " " " " " " " " " " " " " " " " " 001* 002* 003* 004* 005* 006* 007* 008* 009* 010* 011* 012* 013* 014* 015* 016* 017* 018* 019* 66230 " " " " " " " " " " " " " " " " " " Vendor name and address Similar vendor type 1/ Vendor CAGE number Vendor name and address Similar vendor type 1/ Spectrum Control, Incorporated 2185 West Eighth Street Erie, PA 16505 54-310-041 51-320-150 51-320-151 51-320-152 51-320-153 51-320-154 51-320-155 51-320-156 51-320-157 51-320-158 51-320-159 51-321-392 51-321-393 51-321-394 51-321-395 51-321-396 51-321-664 51-321-665 51-321-666 59942 " " " " " " " " " " " " " " " " " " AVX Filters Corporation 11144 Penrose Street Unit 5 Sun Valley, CA 91352 JD1LB-304M* JD2LB-R07M* JD2LB-S07M* JD2LB-R08M* JD2LB-S08M* JD2LB-R10M* JD2LB-S10M* JD2LB-R11M* JD2LB-S11M* JD2LB-R12M* JD2LB-S12M* JD3LB-P07M* JD3LB-P08M* JD3LB-P10M* JD3LB-P11M* JD3LB-P12M* JD4LB-T08M* JD4LB-T09M* JD4LB-T16M* Pacific Aerospace and Electronics Incorporated Filter Division 434 Olds Station Road Wenatchee, WA 98801 3148-9083-100B*C 3342-9083-100B*C 3242-9083-100B*C 3343-9083-100B*C 3243-9083-100B*C 3344-9083-100B*C 3244-9083-100B*C 3345-9083-100B*C 3245-9083-100B*C 3346-9083-100B*C 3246-9083-100B*C 3442-9083-100B*C 3443-9083-100B*C 3444-9083-100B*C 3445-9083-100B*C 3446-9083-100B*C 3543-9083-100B*C 3549-9083-100B*C 3540-9083-100B*C Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER, SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84083 REV H PAGE 9