ispMACH 4000 V/B/C/ZC/ZE Product Family

Lattice ispMACH 4000 V/B/C/ZC/ZE Product Family Qualification Summary
Lattice Document # 25 -105900
October 2012
© 2012 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are listed at www.latticesemi.com/legal. All other
brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change
without notice.
www.latticesemi.com
Dear Customer,
Welcome to the Lattice Semiconductor Corp. ispMACH® 4000 Product Family Qualification
Report. This report reflects our continued commitment to product quality and reliability. The
information in this report is drawn from an extensive qualification program of the wafer technology
and packaging assembly processes used to manufacture our products. The program adheres to
JEDEC and Automotive Industry standards for qualification of the technology and device
packaging. This program ensures you only receive product that meets the most demanding
requirements for Quality and Reliability.
The information contained in this document is extensive, and represents the entire qualification
effort for this device family. Our goal is to provide this information to support your decision
making process, and to facilitate the selection and use of our products.
As always, your feedback is valuable to Lattice. Our goal is to continuously improve our systems,
including the generation of this report and the data included. Please feel free to forward your
comments and suggestions to your local Lattice representative. We will use that feedback carefully
and wisely in our effort to maximize customer satisfaction.
Sincerely,
Michael J. Gariepy
VP Corporate and Customer Quality
LATTICE SEMICONDUCTOR CORP.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
2
1.0 INTRODUCTION .................................................................................................................................................. 5
Table 1.1 Lattice ispMACH 4000 V/B/C Product Family Attributes ........................................................................................... 5
Table 1.2 Lattice ispMACH 4000ZC Product Family Attributes ................................................................................................ 6
Table 1.3 Lattice ispMACH 4000ZE Product Family Attributes ................................................................................................. 6
Table 1.4 Lattice Automotive LA-ispMACH 4000V Product Family Attributes .......................................................................... 7
Table 1.5 Lattice Automotive LA-ispMACH 4000ZC Product Family Attributes........................................................................ 8
2.0 LATTICE PRODUCT QUALIFICATION PROGRAM .......................................................................................... 9
Figure 2.1: ispMACH 4000 Product Qualification Process Flow ............................................................................................ 10
Table 2.2: Standard Qualification Testing ................................................................................................................................ 12
3.0 QUALIFICATION DATA FOR EE9 PROCESS TECHNOLOGY ...................................................................... 13
3.1 EE9 PRODUCT FAMILY LIFE DATA ............................................................................................................................................ 14
Table 3.1.1: EE9 Product Family HTOL Results ...................................................................................................................... 14
Table 3.1.2: EE9 Product Family LTOL Results ....................................................................................................................... 16
3.2 ISPMACH 4000 PRODUCT FAMILY HIGH TEMPERATURE DATA RETENTION (HTRX) ............................................................... 17
Table 3.2.1: EE9 High Temperature Data Retention Results .................................................................................................... 17
3.3 ISPMACH 4000 PRODUCT FAMILY ENDURANCE CYCLING DATA .............................................................................................. 18
Table 3.3.1: EE9 Endurance Cycling Results ........................................................................................................................... 18
........................................................................................................................................................................................................ 18
3.4 ISPMACH 4000 PRODUCT FAMILY – ESD AND LATCH UP DATA (COMMERCIAL/INDUSTRIAL): ............................................... 19
Table 3.4.1 ispMACH 4000 ESD-HBM Data (Commercial/Industrial):................................................................................... 19
Table 3.4.3 ispMACH 4000 ESD-CDM Data (Commercial/Industrial): .................................................................................. 20
Table 3.4.5 ispMACH4000 I/O Latch Up Data (Commercial/Industrial): ................................................................................ 21
Table 3.4.6 ispMACH4000 V-Supply (Over Voltage) Latch Up Data (Commercial/Industrial):.............................................. 22
3.5 LA-ISPMACH 4000V/Z PRODUCT FAMILY – ESD AND LATCH UP DATA (AUTMOTIVE): ......................................................... 23
Table 3.4.2 LA-ispMACH 4000 ESD-HBM Data (Autmotive): ................................................................................................. 23
Table 3.4.4 LA-ispMACH 4000 ESD-CDM Data (Autmotive): ................................................................................................. 23
Table 3.4.7 LA-ispMACH4000 I/O Latch Up Data (Autmotive): .............................................................................................. 24
4.0 PACKAGE QUALIFICATION DATA FOR ISPMACH 4000 FAMILIES ............................................................ 25
Table 4.1 ispMACH 4000 Product-Package Qualification-By-Extension Matrix ..................................................................... 25
Table 4.2 LA-ispMACH 4000 (Automotive) Product-Package Qualification-By-Extension Matrix ......................................... 26
Table 4.3 ispMACH 4000ZE Copper (Cu) Bond Wire Product-Package Qualification-By-Extension Matrix ......................... 26
4.1 ISPMACH 4000 PRODUCT FAMILY SURFACE MOUNT PRECONDITIONING TESTING ................................................................... 27
Table 4.1.1 Surface Mount Precondition Data .......................................................................................................................... 27
4.2 ISPMACH 4000 PRODUCT FAMILY TEMPERATURE CYCLING DATA .......................................................................................... 30
Table 4.2.1: Temperature Cycling Data .................................................................................................................................... 30
4.3 ISPMACH 4000 PRODUCT FAMILY UNBIASED HAST DATA ..................................................................................................... 32
Table 4.3.1: Unbiased HAST Data ............................................................................................................................................ 32
4.4 ISPMACH 4000 PRODUCT FAMILY THB: BIASED HAST DATA ................................................................................................ 34
Table 4.4.1: Biased HAST Data ................................................................................................................................................ 34
4.5 ISPMACH 4000 PRODUCT FAMILY HIGH TEMPERATURE STORAGE LIFE (HTSL)...................................................................... 36
Table 3.2.2: High Temperature Storage Life Results ................................................................................................................ 36
5.0 ISPMACH 4000 PROCESS RELIABILITY WAFER LEVEL REVIEW ............................................................. 37
Table 5.1 – Wafer Level Reliability Results for Seiko EE9 (180nm) Process Technology ........................................................ 37
Table 5.2 – Wafer Level Reliability Results for UMC EE9 (180nm) Process Technology ........................................................ 38
6.0 ISPMACH 4000V/B/C/ZC/ZE SOFT ERROR RATE DATA .............................................................................. 39
7.0 ISPMACH 4000 PACKAGE ASSEMBLY INTEGRITY TESTS......................................................................... 40
7.1 WIRE BOND SHEAR TEST........................................................................................................................................................... 40
7.2 WIRE BOND PULL ...................................................................................................................................................................... 40
7.3 SOLDERABILITY ......................................................................................................................................................................... 40
7.4 PHYSICAL DIMENSIONS ............................................................................................................................................................. 40
7.5 SOLDER BALL SHEAR ................................................................................................................................................................ 40
8.0 ISPMACH 4000 ADDITIONAL FAMILY DATA ................................................................................................. 41
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
3
Table 8.1: ispMACH 4000 Package Assembly Data – csBGA/ ftBGA ...................................................................................... 41
Table 8.2: ispMACH 4000 Package Assembly Data – Au-Wire TQFP ..................................................................................... 42
Table 8.3: ispMACH 4000 Package Assembly Data – Cu-Wire TQFP..................................................................................... 43
9.0 REVISION HISTORY ......................................................................................................................................... 44
Table 9.1: Lattice ispMACH 4000 V/B/C/ZC/ZE Product Family Qualification Summary revisions ........................... 44
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
4
1.0 INTRODUCTION
The ispMACH 4000 Product Family offers a SuperFAST CPLD solution. The ispMACH 4000 Family includes
3.3, 2.5, 1.8 volt power supply, and 1.8- volt zero power versions, designated ispMACH 4000V, ispMACH
4000B, ispMACH 4000C, ispMACH 4000ZC and ispMACH 4000ZE devices respectively. The ispMACH
4000V/B/C/ZC/ZE Product Family offers densities ranging from 32 to 512 macrocells.
The ispMACH 4000V/B/C/ZC/ZE product families are built on Lattice Semiconductor’s 3.3V/2.5V/1.8V EE9
process. EE9 is a shallow trench isolated 0.18um Leff CMOS process with Electrically Erasable cell (E2 cell)
modules. This process uses five, planarized metal interconnect layers and single layer polysilicon.
The ispMACH 4000V/B/C/ZC product family was initially built at United Microelectronics Company (UMC).
The Lattice ispMACH 4256 device was the initial product released to production in May 2001. The additional
foundry, Seiko Epson, was released in July 2003. In 2002, Lattice Semiconductor introduced the extended
temperature grade, -40 to 130°C junction (TJ), ispMACH 4000V/ ZC products (V = 3.3V, Z = zero power, 1.8
V).
This report details the reliability qualification results of the initial ispMACH 4000V/B/C/ZC/ZE product
introduction built at Seiko Epson and United Microelectronics Company (UMC). To verify product reliability,
Lattice Semiconductor maintains an active Early Life and Inherent Life Reliability Monitor program on the
ispMACH 4000 products. Lattice Semiconductor publishes the Reliability Monitor Data quarterly.
Table 1.1 Lattice ispMACH 4000 V/B/C Product Family Attributes
Macrocells
I/O + Dedicated
Inputs
tPD (ns)
tS (ns)
tCO (ns)
fMAX (MHz)
Supply Voltages
(V)
Fabrication Site
Process
Technology
Die Size
(W x L x T)
Die Metallization
Die Interconnect
Dielectric
Pins/Package
ispMACH
4032V/B/C
32
30+2/32+4
2.5
1.8
2.2
400
3.3/2.5/1.8V
ispMACH
4064V/B/C
64
30+2/32+4/64+
10
2.5
1.8
2.2
400
3.3/2.5/1.8V
Seiko Epson /
UMC Taiwan
Seiko Epson /
UMC Taiwan
ispMACH
4128V/B/C
128
64+10/92+4/
96+4
2.7
1.8
2.7
333
3.3/2.5/1.8V
Seiko Epson /
UMC Taiwan
ispMACH
4256V/B/C
256
64+10/96+14/
128+4/160+4
3.0
2.0
2.7
322
3.3/2.5/1.8V
Seiko Epson /
UMC Taiwan
ispMACH
4384V/B/C
384
128+4/192+4
ispMACH
4512V/B/C
512
128+4/208+4
3.5
2.0
2.7
322
3.3/2.5/1.8V
3.5
2.0
2.7
322
3.3/2.5/1.8V
Seiko Epson /
UMC Taiwan
Seiko Epson /
UMC Taiwan
EE9 180nm
(E2 cell)
EE9 180nm (E2
cell)
EE9 180nm
(E2 cell)
EE9 180nm (E2
cell)
EE9 180nm (E2
cell)
EE9 180nm (E2
cell)
1770 x 1910 x
330-381 (um)
Al – 0.5% Cu
Plasmaenhanced
TEOS
44 TQFP
48 TQFP
2530 x 2330 x
330-381 (um)
Al – 0.5% Cu
Plasmaenhanced TEOS
3280 x 3150 x
330-381 (um)
Al – 0.5% Cu
Plasmaenhanced
TEOS
3530 x 4180 x
330-381 (um)
Al – 0.5% Cu
Plasma-enhanced
TEOS
5300 x 5000 x
330-381 (um)
Al – 0.5% Cu
Plasmaenhanced TEOS
5400 x 5500 x
330-381 (um)
Al – 0.5% Cu
Plasmaenhanced TEOS
100 TQFP
128 TQFP
144 TQFP1
100 TQFP
176 TQFP
256
ftBGA/fpBGA3
176 TQFP
256
ftBGA/fpBGA3
44 TQFP
48 TQFP
100 TQFP
144 TQFP1
176 TQFP
256
ftBGA²/fpBGA2, 3
1. 3.3V (4000V) only.
2. 128-I/O and 160-I/O configurations.
3. Use 256 ftBGA package for all new designs. Refer to PCN#14A-07 for 256 fpBGA package discontinuance.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
5
Table 1.2 Lattice ispMACH 4000ZC Product Family Attributes
Macrocells
I/O + Dedicated Inputs
tPD (ns)
tS (ns)
tCO (ns)
fMAX (MHz)
Supply Voltages (V)
Max, Standby Icc (µA)
Fabrication Site
Process Technology
Die Size
(W x L x T)
Die Metallization
Die Interconnect
Dielectric
Pins/Package
ispMACH
4032ZC
32
32+4/32+4
3.5
2.2
3.0
267
1.8
20
Seiko Epson /
UMC Taiwan
EE9 180nm (E2 cell)
1770 x 1910 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
48 TQFP
56 csBGA
ispMACH
4064ZC
64
32+4/32+12/
64+10/64+10
3.7
2.5
3.2
250
1.8
25
Seiko Epson /
UMC Taiwan
EE9 180nm (E2 cell)
2490 x 1960 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
ispMACH
4064ZC
128
64+10/96+4
4.2
2.7
3.5
220
1.8
35
Seiko Epson /
UMC Taiwan
EE9 180nm (E2 cell)
2490 x 1960 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
48 TQFP
56 csBGA
100 TQFP
132 csBGA
100 TQFP
132 csBGA
ispMACH
4256ZC
256
64+10/96+6/
128+4
4.5
2.9
3.8
200
1.8
55
Seiko Epson /
UMC Taiwan
EE9 180nm (E2 cell)
3530 x 4180 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
100 TQFP
132 csBGA
176 TQFP
Table 1.3 Lattice ispMACH 4000ZE Product Family Attributes
tPD (ns)
tS (ns)
tCO (ns)
fMAX (MHz)
Supply Voltages (V)
Fabrication Site
4.4
2.2
3.0
260
1.8V
Seiko Epson /
UMC Taiwan
ispMACH
4064ZE
64
32+4/48+4/48+4
64+10/64+10
4.7
2.5
3.2
241
1.8V
Seiko Epson /
UMC Taiwan
Process Technology
Die Size
(W x L x T)
Die Metallization
Die Interconnect
Dielectric
Pins/Packages
(Lead-Free only)
EE9 180nm (E2 cell)
1770 x 1910 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
EE9 180nm (E2 cell)
2490 x 1960 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
48 TQFP
64 csBGA
48 TQFP
64 csBGA
64 ucBGA
100 TQFP
Macrocells
I/O + Dedicated Inputs
ispMACH
4032ZE
32
32+4/32+4
144 csBGA
ispMACH
4128ZE
128
64+10/96+4/96+4/ 96+4
5.8
2.9
3.8
200
1.8V
Seiko Epson
ispMACH
4256ZE
256
64+10/96+14/
108+4
5.8
2.9
3.8
200
1.8V
Seiko Epson
EE9 180nm (E2 cell)
3280 x 3150 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
EE9 180nm (E2 cell)
3530 x 4180 x 330-381
(um)
Al – 0.5% Cu
Plasma-enhanced TEOS
100 TQFP
132 ucBGA
144 TQFP
144 csBGA
100 TQFP
144 TQFP
144 csBGA
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
6
Lattice offers automotive version of ispMACH 4000 family. This high performance LA-ispMACH 4000V
automotive family offers a SuperFAST 3.3 volt CPLD solution that is tested and qualified to the AEC-Q100
standard.
The LA-ispMACH 4000ZC automotive family combines high speed and low power with the flexibility needed
for ease of design. With its robust Global Routing Pool and Output Routing Pool, this family delivers excellent
First-Time-Fit, timing predictability, routing, pin-out retention and density migration.
The LA-ispMACH 4000V automotive family offers densities ranging from 32 to 128 macrocells. There are
multiple density-I/O combinations in Thin Quad Flat Pack (TQFP) packages ranging from 44 to 144 pins. Table
1.4 shows the macrocell, package and I/O options, along with other key parameters.
Table 1.4 Lattice Automotive LA-ispMACH 4000V Product Family Attributes
Macrocells
I/O + Dedicated Inputs
tPD (ns)
tS (ns)
tCO (ns)
fMAX (MHz)
Supply Voltage (V)
Fabrication Site
Process Technology
Die Size (W x L x T)
Die Metallization
Die Interconnect Dielectric
Pins/Package
(Lead-Free Only)
LA-ispMACH
4032V
32
30+2/32+4
7.5
4.5
4.5
168
3.3V
Seiko Epson
EE9 180nm (E2 cell)
1770 x 1910 x 330-381 (um)
Al – 0.5% Cu
Plasma-enhanced TEOS
44 TQFP
48 TQFP
LA-ispMACH
4064V
64
30+2/32+4/64+10
7.5
4.5
4.5
168
3.3V
Seiko Epson
EE9 180nm (E2 cell)
2490 x 1960 x 330-381 (um)
Al – 0.5% Cu
Plasma-enhanced TEOS
44 TQFP
48 TQFP
100 TQFP
LA-ispMACH
4128V
128
64+10/92+4/96+4
7.5
4.5
4.5
168
3.3V
Seiko Epson
EE9 180nm (E2 cell)
3280 x 3150 x 330-381 (um)
Al – 0.5% Cu
Plasma-enhanced TEOS
100 TQFP
128 TQFP
144 TQFP
The LA-ispMACH 4000V automotive family has enhanced system integration capabilities. It supports 3.3V
supply voltages and 3.3V, 2.5V and 1.8V interface voltages. Additionally, inputs can be safely driven up to 5.5V
when an I/O bank is configured for 3.3V operation, making this family 5V tolerant. The LA-ispMACH 4000V
also offers enhanced I/O features such as slew rate control, PCI compatibility, bus-keeper latches, pull-up
resistors, pull-down resistors, open drain outputs and hot socketing. The LA-ispMACH 4000V automotive
family is in-system programmable through the IEEE Standard 1532 interface. IEEE Standard 1149.1 boundary
scan testing capability also allows product testing on automated test equipment.
The LA-ispMACH 4000ZC automotive family shares most of the same traits as the LA-ispMACH4000V
family. The exception is that the Supply Voltage is 1.8V which categorizes this part as Low-Power. The LAispMACH 4000ZC automotive family offers densities ranging from 32 to 128 macrocells. There are multiple
density-I/O combinations in Thin Quad Flat Pack (TQFP) packages ranging from 44 to 144 pins. Table 1.5
shows the macrocell, package and I/O options, along with other key parameters.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
7
Table 1.5 Lattice Automotive LA-ispMACH 4000ZC Product Family Attributes
LA-ispMACH
4032ZC
32
LA-ispMACH
4064ZC
64
LA-ispMACH
4128ZC
128
32+4
32+4/64+10
64+10
tPD (ns)
7.5
7.5
7.5
tS (ns)
4.5
4.5
4.5
tCO (ns)
4.5
4.5
4.5
Macrocells
I/O + Dedicated Inputs
fMAX (MHz)
168
168
168
Supply Voltage (V)
1.8V
1.8V
1.8V
Seiko Epson
Seiko Epson
Seiko Epson
Process Technology
EE9 180nm (E2 cell)
EE9 180nm (E2 cell)
EE9 180nm (E2 cell)
Die Size (W x L x T)
1770 x 1910 x 330-381 (um)
2490 x 1960 x 330-381 (um)
3280 x 3150 x 330-381 (um)
Al – 0.5% Cu
Al – 0.5% Cu
Al – 0.5% Cu
Plasma-enhanced TEOS
Plasma-enhanced TEOS
48 TQFP
100 TQFP
Plasma-enhanced TEOS
Fabrication Site
Die Metallization
Die Interconnect Dielectric
Pins/Package
(Lead-Free Only)
48 TQFP
100 TQFP
The LA-ispMACH 4000V/ZC automotive family is built on the 0.18 um EE9 Electrically Erasable (E2 cell
based) CMOS process at Seiko Epson and assembled at Amkor Technology, Korea and Advance Semiconductor
Engineering, Malaysia (ASEM) in Pb-free TQFP packages. This report includes the automotive reliability
qualification and device characterization results of the initial Lattice Automotive LA4000V/ZC Product Family
introduction.
This report summarizes the qualification results for all Lattice ispMACH 4000V/B/C/ZC/ZE and LAispMACH4000V/ZC products as ofJuly 2011.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
8
2.0 LATTICE PRODUCT QUALIFICATION PROGRAM
Lattice Semiconductor Corp. maintains a comprehensive reliability qualification program to assure that
each product achieves its reliability goals. After initial qualification, the continued high reliability of
Lattice products is assured through ongoing monitor programs as described in Reliability Monitor
Program Procedure (Doc. #70-101667). All product qualification plans are generated in conformance
with Lattice Semiconductor’s Qualification Procedure (Doc. #70-100164) with failure analysis
performed in conformance with Lattice Semiconductor’s Failure Analysis Procedure (Doc. #70100166). Both documents are referenced in Lattice Semiconductor’s Quality Assurance Manual,
which can be obtained upon request from a Lattice Semiconductor sales office. Figure 2.1 shows the
Product Qualification Process Flow.
If failures occur during qualification, an 8 Discipline (8D) process is used to find root cause and
eliminate the failure mode from the design, materials, or process. The effectiveness of any fix or
change is validated through additional testing as required. Final testing results are reported in the
qualification reports.
Failure rates in this reliability report are expressed in FITS. Due to the very low failure rate of
integrated circuits, it is convenient to refer to failures in a population during a period of 109 device
hours; one failure in 109 device hours is defined as one FIT.
Product families are qualified based upon the requirements outlined in Tables 2.2. In general, Lattice
Semiconductor follows the current Joint Electron Device Engineering Council (JEDEC) and Military
Standard testing methods. Lattice automotive products are qualified and characterized to the
Automotive Electronics Council (AEC) testing requirements and methods. Product family
qualification will include products with a wide range of circuit densities, package types, and package
lead counts. Major changes to products, processes, or vendors require additional qualification before
implementation.
The ispMACH 4000V/B/C/ZC/ZE and LA-ispMACH 4000V/ZC product families are built on Lattice
Semiconductor’s 1.8V/2.5V/3.3V EE9 process. EE9 is a shallow trench isolated 0.18um Leff CMOS
process with Electrically Erasable cell (E2 cell) modules. This process uses five, planarized metal
interconnect layers and single layer polysilicon.
Lattice Semiconductor maintains a regular reliability monitor program. The current Lattice Reliability
Monitor Report can be found at www.latticesemi.com/lit/docs/qa/product_reliability_monitor.pdf .
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
9
Figure 2.1: ispMACH 4000 Product Qualification Process Flow
Qualification
Plan Request










Determine
Generic
Qualification
Type
New Foundry Technology
Process Change
Foundry Transfer
New Product Family
Add Product to Family
Design Change
New Package Technology
Package Materials Change
Assembly Transfer
Expand Die or Package Size
Automotive or
Commercial?
Automotive
AEC-Q100
Standard
Qualification
Requirements
Commercial /
Industrial
JESD47
Standard
Qualification
Check for
Customer Specific
Requirements
Generate FMEA:
Risk Management
& Lessons Learned
Generate
Qualification Plan
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
10
Approved
Qualification Plan
Qualifiable
Material Review
Commercial
Automotive
Automotive
or
Commercial?
Commercial
Room Temperature
Pre-stress testing
& data logging
Automotive
3-Temperature
Pre-stress testing
& data logging
JEDEC standard based reliability stressing
Room Temperature
Post-stress testing
& data logging
3-Temperature
Post-stress testing
& data logging
Qualification
Failures?
Failure
Analysis
Qualification
Report
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
11
Table 2.2: Standard Qualification Testing
TEST
STANDARD
TEST CONDITIONS
High Temperature
Operating Life
HTOL
Lattice Procedure
# 87-101943,
MIL-STD-883,
Method 1005.8,
JESD22-A10
125° C,
Maximum operating Vcc,
168, 500, 1000, 2000 hrs.
High Temp Data
Retention
HTRX
ispMACH-4000
LA-ispMACH-4000
Lattice Procedure
# 87-101925,
JESD22-A117
ispMACH-4000
LA-ispMACH-4000
High Temp Storage Lattice Procedure
Life
# 87-101925,
HTSL
JESD22-A103
Endurance Program/Erase
Cycling
Flash based
Products
ESD HBM
ESD CDM
Latch Up
Resistance
LU
ispMACH-4000
LA-ispMACH-4000
Lattice Procedure,
# 70-104633
JESD22-A117
ispMACH-4000
LA-ispMACH-4000
Lattice Procedure
# 70-100844,
MIL-STD-883, Method
3015.7
JESD22-A114
Lattice Procedure
# 70-100844,
JESD22-C101
Lattice Procedure
# 70-101570,
JESD78
Surface Mount Pre- Lattice Procedure
conditioning
# 70-103467,
SMPC
IPC/JEDEC
J-STD-020D.1
JESD-A113
Temperature
Cycling
TC
Unbiased HAST
UHAST
CPLD/FPGA - MSL 3
Lattice Procedure
#70-101568,
MIL-STD- 883, Method
1010, Condition B
JESD22-A104
Lattice Procedure
# 70-104285
JESD22-A118
SAMPLE SIZE PERFORMED ON
(Typ)
77/lot
Design, Foundry
2-3 lots
Process, Package
Qualification
Preconditioned with 100
read/write cycles
150° C,
Maximum operating Vcc,
168, 500, 1000, 2000 hrs.
100/lot
2-3 lots
Design, Foundry
Process, Package
Qualification
Preconditioned with 100
read/write cycles
150° C, at 168, 500, 1000,
2000 hours.
Program/Erase
devices to 10,000 cycles
E2 Cell Products
Flash based Products
77/lot
2-3 lots
Design, Foundry
Process, Package
Qualification
10/lot
Design, Foundry
2-3 lots typical Process, Package
Qualification
Program/Erase devices to
10X cycles of data sheet
specification
Human Body Model
3 parts/lot
Design, Foundry Process
(HBM) sweep to 2000 volts 1-3 lots typical
– (130nm and older)
Charged Device model
(CDM) sweep to 1000 volts
(130nm and older)
±100 ma on I/O's,
Vcc +50% on Power
Supplies. (Max operating
temp.)
10 Temp cycles,
24 hr 125° C Bake
192hr. 30/60 Soak
3 SMT simulation cycles
3 parts/lot
Design, Foundry Process
1-3 lots typical
6 parts/lot
Design, Foundry Process
1-3 lots typical
All units going Plastic Packages only
into
Temp Cycling,
UHAST,
BHAST,
85/85
(1000 cycles) Repeatedly
cycled between -55° C and
+125° C in an air
environment
45 parts/lot
2-3 lots
Design, Foundry
Process, Package
Qualification
96 hrs, 130 C, or
264 hrs 110 C, and
85% Relative Humidity
45 parts/lot
2-3 lots
Foundry Process,
Package Qualification
Plastic Packages only
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
12
TEST
STANDARD
Moisture Resistance Lattice Procedure
Temperature
# 70-101571,
Humidity Bias
JESD22-A101
85/85
THBS
or
Biased HAST
BHAST
JESD22-A110
TEST CONDITIONS
SAMPLE SIZE PERFORMED ON
(Typ)
Biased to maximum
45 devices/lot Design, Foundry
operating Vcc, 85° C, 85%
2-3 lots
Process, Package
Relative Humidity,
Qualification
1000 hours
Plastic Packages only
or
Biased to maximum
operating Vcc,
96 hrs, 130 C,
85% Relative Humidity
or
Biased to maximum
operating Vcc,
264 hrs 110 C, and
85% Relative Humidity
Measure all dimensions
listed on the case outline.
Physical
Dimensions
Lattice Procedure
# 70-100211,
MIL-STD- 883 Method
2016 or applicable LSC
case outline drawings
Wire Bond Strength Lattice Procedure
Per package type
# 70-100220
Solderability
Lattice Procedure
# 70-100212,
MIL-STD-883, Method
2003
Steam Pre-conditioning
4-8 hours. Solder dip
at 245°C+5°C
5 devices
Package Qualification
15 devices per Design, Foundry
pkg. per year Process, Package
Qualification
22 leads/
All packages except
3 devices/
BGAs
Package family
3.0 QUALIFICATION DATA FOR EE9 PROCESS TECHNOLOGY
The ispMACH 4000V/B/C/ZC/ZE product family is built on Lattice Semiconductor’s EE9 180nm
E2CMOS process technology. The ispMACH 4000V/B/C/ZC product family was initially built at
United Microelectronics Company (UMC). The Lattice ispMACH 4256 device was the initial product
released to production in May 2001. The additional foundry, Seiko Epson, was released in July 2003.
The LA-ispMACH 4000V/ZC automotive family was qualified for automotive applications using the
Stress Test Qualification for Integrated Circuits, AEC-Q100-Rev-F, test requirements and methods.
The LA-ispMACH 4000V/ZC automotive family operates over the Automotive Grade 1 (-400C to
+1250C) ambient operation temperature range. All low and high temperature test read-outs were
performed at the Grade 1 temperature extremes.
Product Family: ispMACH 4000V/B/C/ZC/ZE, LA-ispMACH 4000V/ZC
Packages offered: csBGA, ftBGA, fpBGA, ucBGA and TQFP
Process Technology Node: 180nm
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
13
3.1 EE9 Product Family Life Data
High Temperature Operating Life (HTOL) Test
The High Temperature Operating Life test is used to thermally accelerate those wear out and failure
mechanisms that would occur as a result of operating the device continuously in a system application.
Consistent with JEDEC JESD22-A108 “Temperature, Bias, and Operating Life”, a pattern specifically
designed to exercise the maximum amount of circuitry is programmed into the device and this pattern
is continuously exercised at specified voltages as described in test conditions for each device type.
EE9 Life Test (HTOL) Conditions:
Stress Duration: 48, 168, 500, 1000, 2000 hours.
Temperature: 125°C
Stress Voltage ispMACH 4000V/B/C/ZC/ZE: VCC=1.95V
Stress Voltage LA-ispMACH 4000V: VCC=3.6V/ VCCIO=3.6V
Stress Voltage LA-ispMACH 4000ZC: VCC=2.0V / VCCIO=3.6V
Preconditioned with 1000 read/write cycles
Method: Lattice Document # 87-101943 and JESD22-A108C
Table 3.1.1: EE9 Product Family HTOL Results
77
168 Hrs
Result
0
500 Hrs
Result
0
Lot #2
77
0
0
0
Seiko
Lot #1
77
0
0
0
77,000
Seiko
Lot #2
77
0
0
0
77,000
LC4064ZC
Seiko
Lot #1
77
0
0
0
77,000
LC4064ZC
Seiko
Lot #2
77
0
0
0
77,000
0
0
76,000*
Product Name
Foundry
Lot #
Qty
LC4032ZC
Seiko
Lot #1
LC4032ZC
Seiko
LC4032ZE
LC4032ZE
LC4064ZE
Seiko
Lot #1
48 Hrs
Result
77
1
A
B
1000 Hrs 2000 Hrs
Result
Result
0
0
0
0
Cumulative
Hours
154,000
154,000
LC4064ZE
Seiko
Lot #2
77
0
1
LC4128
Seiko
Lot #1
77
0
0
0
0
76,000*
154,000
LC4128
Seiko
Lot #2
77
0
0
0
0
154,000
LC4256
Seiko
Lot #1
77
0
0
0
0
154,000
LC4256
Seiko
Lot #2
64
0
0
0
0
128,000
LC4256
Seiko
Lot #3
129
0
0
0
0
258,000
LC4256
Seiko
Lot #4
120
0
0
0
0
240,000
LC4256
Seiko
Lot #5
120
0
0
0
0
240,000
LC4032
UMC
Lot#1
77
0
0
0
0
154,000
LC4032ZC
UMC
Lot#1
77
0
0
0
0
154,000
LC4064
UMC
Lot#1
77
0
0
0
0
154,000
LC4064
UMC
Lot#2
77
0
0
0
0
154,000
LC4128
UMC
Lot#1
77
0
0
0
0
154,000
LC4256
UMC
Lot#1
174
0
0
0
0
0
174,000
C
LC4256
UMC
Lot#2A
169
1
LC4256
UMC
Lot#2B
186
0
0
372,000
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
14
Product Name
Foundry
Lot #
Qty
48 Hrs
Result
LC4256
UMC
Lot#2C
179
168 Hrs
Result
0
LC4256
UMC
Lot#3
173
0
LC4256
UMC
Lot#4
83
0
0
0
0
166,000
LC4256
UMC
Lot#5
90
0
0
0
0
180,000
LC4256
UMC
Lot#6
90
0
0
0
LC4384
UMC
Lot#1
77
0
0
0
0
154,000
LC4512
UMC
Lot#1
77
0
0
0
0
154,000
LC4512
UMC
Lot#2
77
0
0
0
0
154,000
LA4064V
Seiko
Lot#1
77
0
0
0
77,000
LA4064V
Seiko
Lot#2
77
0
0
0
77,000
LA4064V
Seiko
Lot#3
78
0
0
0
77,000
LA4064V
Seiko
Lot#1
80
0
0
0
80,000
LA4064V
Seiko
Lot#2
80
0
0
0
80,000
LA4064V
Seiko
Lot#3
79
0
0
0
79,000
LA4064ZC
Seiko
Lot#4
128
0
0
0
128,000
LA4064ZC
Seiko
Lot#5
130
0
0
0
130,000
LA4032ZC
Seiko
Lot#1
793
0
LA4032ZC
Seiko
Lot#2
799
0
LA4032ZC
Seiko
Lot#3
802
0
LA4032V
Seiko
Lot#1
798
0
LA4032V
Seiko
Lot#2
800
0
LA4032V
Seiko
Lot#3
798
0
LC4032ZE
UMC
Lot#1
800
0
LC4032ZE
UMC
Lot#2
744
0
LC4064ZE
UMC
Lot#3
730
0
A: 1* unit failed for EOS. FAR#1376
B: 1* unit failed for EOS. FAR#1376
500 Hrs
Result
0
1000 Hrs 2000 Hrs
Result
Result
0
Cumulative
Hours
179,000
90,000
FIT Rate Assumptions:
Tjstress=125C, Tjref=55C, Activation Energy = 0.5eV
* EOS units discounted from cumulative hours.
C: 1 unit failed ELFR. Root cause unknown.
EE9 Cumulative HTOL Device Hours = 5,613,360
EE9 Cumulative HTOL Sample Size = 1 / 3,426
EE9 FIT Rate = 16 FIT
EE9 Seiko Cumulative HTOL Device Hours = 3,053,920
EE9 Seiko HTOL Sample Size = 0 / 2,008
EE9 Seiko FIT Rate = 13 FIT
EE9 UMC Cumulative HTOL Device Hours = 2,559,440
EE9 UMC HTOL Sample Size = 1 / 1,418
EE9 UMC FIT Rate = 35 FIT
EE9 ELFR (48 or 168 Hrs) Cumulative Results = 1 / 10,833
EE9 UMC ELFR (48 or 168 Hrs) Results = 1 / 4,034
EE9 Seiko ELFR (48 or 168 Hrs) Results = 0 / 6,838
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
15
Low Temperature Operating Life (LTOL) Test
The Low Temperature Operating Life test is used to accelerate gain onto the floating gate due to hot
electron effects. A pattern specifically designed to exercise the maximum amount of circuitry is
programmed into the device and this pattern is continuously exercised at 1.95V and -55°C.
EE9 Life Test (LTOL) Conditions:
Stress Duration: 168, 500, 1000 hours.
Temperature: -55°C
Stress Voltage ispMACH 4000: VCC=1.95V
Preconditioned with 1000 read/write cycles
Method: Lattice Document # 87-101943 and JESD22-A108C
Table 3.1.2: EE9 Product Family LTOL Results
Product Name
LC4256
Foundry
UMC
Lot #
Qty
168 Hrs
Result
500 Hrs
Result
Lot #2
45
0
0
1000 Hrs Cumulative
Result
Hours
0
45000
EE9 Cumulative LTOL Failure Rate = 0 / 45
EE9 Cumulative LTOL Device Hours = 45,000
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
16
3.2 ispMACH 4000 Product Family High Temperature Data Retention (HTRX)
High Temperature Data Retention (HTRX)
The High Temperature Data Retention test measures the Electrically Erasable cell (E2 cell) reliability
while the High Temperature Operating Life test is structured to measure functional operating circuitry
failure mechanisms. The High Temperature Data Retention test is specifically designed to accelerate
charge gain on to or charge loss off of the floating gates in the device's array. Since the charge on
these gates determines the actual pattern and function of the device, this test is a measure of the
reliability of the device in retaining programmed information. In High Temperature Data Retention,
the E2 cell reliability is determined by monitoring the cell margin after biased static operation at
150°C. All cells in all arrays are life tested in both programmed and erased states.
EE9 Data Retention (HTRX) Conditions:
Stress Duration: 168, 500, 1000, 2000 hours.
Temperature: 150°C
Stress Voltage ispMACH 4000: VCC = 1.95V
Stress Voltage LA-ispMACH 4064V: VCC = 3.6V
Method: Lattice Document # 87-101925 and JESD22-A103C / JESD22-A117A
Table 3.2.1: EE9 High Temperature Data Retention Results
Product Name
Foundry
Lot #
Qty
168 Hrs
Result
500 Hrs
Result
1000 Hrs 2000 Hrs Cumulative
Result
Result
Hours
LC4128
Seiko
Lot #1
40
0
0
0
0
80,000
LC4128
Seiko
Lot #2
40
0
0
0
0
80,000
LC4256
Seiko
Lot #1
45
0
0
0
0
90,000
LC4256
Seiko
Lot #3
110
0
0
0
0
220,000
LC4256
Seiko
Lot #4
90
0
0
0
0
180,000
LC4256
Seiko
Lot #5
90
0
0
0
0
180,000
LC4256
UMC
Lot #1
90
0
0
45,000
LC4256
UMC
Lot #2
90
0
0
45,000
LC4256
UMC
Lot #3
90
0
0
45,000
LC4256
UMC
Lot #4
90
0
0
45,000
LC4256
UMC
Lot #5
90
0
0
0
90,000
LC4256
UMC
Lot #6
90
0
0
0
90,000
LC4256
UMC
Lot #1
90
0
0
0
90,000
LA4064V
Seiko
Lot #1
79
0
0
0
79,000
LA4064V
Seiko
Lot #2
79
0
0
0
79,000
LA4064V
Seiko
Lot #3
80
0
0
0
80,000
EE9 Cumulative HTRX Failure Rate = 0 / 1,283
EE9 Cumulative HTRX Device Hours = 1,518,000
EE9 Seiko HTRX Results = 0 / 653
EE9 UMC HTRX Results = 0 / 630
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
17
3.3 ispMACH 4000 Product Family Endurance Cycling Data
Endurance testing measures the durability of the device through programming and erase cycles.
Endurance testing consists of repeatedly programming and erasing all cells in the array at 25°C to
simulate programming cycles the user would perform. This test evaluates the integrity of the thin
tunnel oxide through which current passes to program the floating gate in each cell of the array.
EE9 Endurance Cycling Test Conditions:
Stress Duration: 1K, 2K, 3K, 5K, 10K Cycles
Temperature: 25°C
Stress Voltage ispMACH 4000: VCC = 1.8V
Method: Lattice Document # 70-104633 and JESD22-A117A
Table 3.3.1: EE9 Endurance Cycling Results
1K CYC 2K CYC
Result
Result
0
0
3K CYC 5K CYC 10K CYC Cumulative
Result
Result
Result Device Cycles
0
0
0
120,000
Product Name
Foundry
Lot #
Qty
LC4256
Seiko
Lot #3
12
LC4256
Seiko
Lot #4
10
0
0
0
0
0
100,000
LC4256
Seiko
Lot #5
10
0
0
0
0
0
100,000
LC4256
UMC
Lot #1
29
0
0
0
0
0
290,000
LC4256
UMC
Lot #2
23
0
0
0
0
0
230,000
LC4256
UMC
Lot #5
10
0
0
0
0
0
100,000
LC4256
UMC
Lot #6
10
0
0
0
0
0
100,000
LC4256
UMC
Lot #1
10
0
0
0
0
0
100,000
LC4256
UMC
Lot #2
10
0
0
0
0
0
100,000
EE9 Cumulative EE Cell Endurance Failure Rate = 0 / 124
EE9 Cumulative EE Cell Endurance Device Cycles = 1,240,000
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
18
3.4 ispMACH 4000 Product Family – ESD and Latch UP Data (Commercial/Industrial):
Electrostatic Discharge-Human Body Model (Commercial/Industrial):
ispMACH 4000 product family was tested per the JESD22-A114E Electrostatic Discharge (ESD)
Sensitivity Testing Human Body Model (HBM) procedure and Lattice Procedure # 70-100844.
All units were tested at 250C prior to reliability stress and after reliability stress. No failures were
observed within the passing classification.
Table 3.4.1 ispMACH 4000 ESD-HBM Data (Commercial/Industrial):
Device
LC4032B-TN44
LC4032V-TN44
LC4032ZC-TN44
LC4032ZE-TN48
LC4032ZE-MN64
LC4064B-TN44
LC4064V-TN44
LC4064ZE-TN48
LC4064ZE- MN64
LC4064B-TN100
LC4064V-TN100
LC4064ZC-TN100
LC4064ZE-TN100B
LC4064ZE-TCN100C
LC4128ZC-TN100
LC4128ZE-TN100B
LC4128ZE-TCN100C
LC4128C-TN128
LC4128ZE-TN144B
LC4128ZE-TCN144C
LC4128ZE-MN144
LC4128ZE-TN144D
LC4128ZE-MN144D
LC4256ZE-TN100
LC4256ZE-TN100B
LC4256ZE-MN144
LC4256ZE-TN144B
LC4256ZE-TCN144C
LC4256B-FN256
LC4256V-FN256
LC4384B-FN256
LC4384V-FN256
LC4512B-FN256
LC4512V-FN256
LC4512B-FT256
LC4512V-FT256
HBM Passing Voltage
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 VA
> 2000 VA
> 2000 V
> 2000 V
> 2000 V
> 2000 VA
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 1500 V
> 1600 V
> 1800 V
> 1800 V
> 1900 V
> 1900 V
> 1900 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
> 2000 V
JEDEC HBM Classification
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 1C
Class 1C
Class 1C
Class 1C
Class 1C
Class 1C
Class 1C
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
HBM classification for Commercial/Industrial products, per JESD22-A114
A: LC4064ZE from UMC >2000V for all pins, all lot #s. LC4064ZE from Seiko with Inspection lot # x122xxxx or later meet >2000V for all pins.
LC4064ZE from Seiko with Inspection lot # x121xxxx or earlier pass all HBM test conditions of >2000V except for the following combinations, which
pass >700V: Positive Vcc to Vss, negative Vss to Vcc, and negative IOs to Vcc.
B: LC4064ZE- TN100, LC4128ZE-TN100 and LC4128ZE-TN144 and LC4256ZE-TCN144 from Seiko+UTAC: include 0.8mil diameter Au bond wire.
C: LC4064ZE-TCN100, LC4128ZE-TCN100, LC4128ZE-TCN144 and LC4256ZE-TCN144 bill-of-materials include Cu bond wires.
D: LC4128ZE-TN144/MN144, data is on UMC silicon.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
19
Electrostatic Discharge-Charged Device Model (Commercial/Industrial):
ispMACH4000 product family was tested per the JESD22-C101D, Field-Induced Charged-Device
Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components
procedure and Lattice Procedure # 70-100844.
All units were tested at 25oC prior to reliability stress and after reliability stress. No failures were
observed within the passing classification.
Table 3.4.3 ispMACH 4000 ESD-CDM Data (Commercial/Industrial):
Device
LC4032B-TN44
LC4032V-TN44
LC4032ZC-TN44
LC4032ZE-TN48
LC4032ZE-MN64
LC4064B-TN44
LC4064V-TN44
LC4064ZE-TN48
LC4064ZE-MN64
LC4064V-TN100
LC4064B-TN100
LC4064ZC-TN100
LC4064ZE-TN100B
LC4064ZE-TCN100C
LC4128ZC-TN100
LC4128ZE-TN100B
LC4128ZE-TCN100C
LC4128C-TN128
LC4128ZE-TN144B
LC4128ZE-TN144D
LC4128ZE-TCN144C
LC4128ZE-MN144
LC4256ZE-TN100
LC4256ZE-TN100B
LC4256ZE-MN144
LC4256ZE-TN144B
LC4256ZE-TCN144C
LC4256B-FN256
LC4256V-FN256
LC4384B-FN256
LC4384V-FN256
LC4512B-FN256
LC4512V-FN256
LC4512B-FT256
CDM Passing Voltage
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 1000V
> 900V
> 900V
> 1000V
> 900V
> 1000V
> 750V
> 700V
> 900V
> 800V
> 1000V
> 900V
> 1000V
> 700V
> 800V
> 750V
> 750V
> 750V
> 750V
> 600V
> 600V
> 650V
> 650V
JEDEC CDM Classification
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class IV
Class III
Class III
Class IV
Class III
Class IV
Class III
Class III
Class III
Class III
Class IV
Class III
Class IV
Class III
Class III
Class III
Class III
Class III
Class III
Class III
Class III
Class III
Class III
CDM classification for Commercial/Industrial products, per JESD22-C101
B: LC4064ZE- TN100, LC4128ZE-TN100 and LC4128ZE-TN144 and LC4256ZE-TCN144 from Seiko+UTAC: include 0.8mil diameter Au bond wire.
C: LC4064ZE-TCN100, LC4128ZE-TCN100, LC4128ZE-TCN144 and LC4256ZE-TCN144 bill-of-materials include Cu bond wires.
D: LC4128ZE-TN144, data is on UMC silicon.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
20
Latch-Up (Commercial/Industrial):
ispMACH 4000 product family was tested per the JEDEC EIA/JESD78A IC Latch-up Test procedure
and Lattice Procedure # 70-101570.
All units were tested at 25oC prior to reliability stress and after reliability stress. No failures were
observed within the passing classification.
Earlier latch-up testing at Lattice was hardware limited to room temperature testing. Additionally,
maximum-rated ambient temperature latch-up testing is generally considered to be approximately 2X
worse than the trigger values found at room temperature. In order to guard band our room temperature
IO latch-up testing the standard was 4X, or +/- 400mA trigger current. Therefore, the previous Lattice
I/O LU standard was >400mA at room temperature, while the present standard is >100mA at
maximum-rated ambient temperature.
Table 3.4.5 ispMACH4000 I/O Latch Up Data (Commercial/Industrial):
Device
LC4032B-TN44
LC4032V-TN44
LC4032ZC-TN44
LC4032ZE-TN48
LC4064B-TN44
LC4064V-TN44
LC4064B-TN100
LC4064V-TN100
LC4064ZC-TN100
LC4064ZE-TN100B
LC4064ZE-TCN100C
LC4128ZE-TN100B
LC4128ZE-TCN100C
LC4128ZC-TN100
LC4128C-TN128
LC4128ZE-TN144B
LC4128ZE-TN144D
LC4128ZE-MN144D
LC4128ZE-TCN144C
LC4256ZE-TN100B
LC4256ZE-TN144B
LC4256ZE-TCN144C
LC4256ZE-TN144
LC4256B-FN256
LC4256V-FN256
LC4384B-FN256
LC4384V-FN256
LC4512B-FN256
LC4512V-FN256
LC4512B-FT256
LC4512V-FT256
I/O Latch-up Results
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 100mA @ 125°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 400mA @ 25°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
+/- 100mA @ 125°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 400mA @ 25°C
+/- 100mA @ 125°C
+/- 100mA @ 125°C
+/- 100mA @ 105°C
+/- 100mA @ 105°C
Jedec/JESD78 Latch-up Level
Class I, Level B
Class I, Level B
Class I, Level B
Class II, Level A
Class I, Level B
Class I, Level B
Class II, Level A
Class II, Level A
Class I, Level B
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class I, Level B
Class I, Level B
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Class I, Level B
Class I, Level B
Class I, Level B
Class I, Level B
Class II, Level A
Class II, Level A
Class II, Level A
Class II, Level A
Latch up classification for Commercial/Industrial products, per JESD78
B: LC4064ZE- TN100, LC4128ZE-TN100 and LC4128ZE-TN144 and LC4256ZE-TCN144 from Seiko+UTAC: include 0.8mil diameter Au bond wire.
C: LC4064ZE-TCN100, LC4128ZE-TCN100, LC4128ZE-TCN144 and LC4256ZE-TCN144 bill-of-materials include Cu bond wires.
D: LC4128ZE-TN144/MN144, data is on UMC silicon.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
21
Table 3.4.6 ispMACH4000 V-Supply (Over Voltage) Latch Up Data
(Commercial/Industrial):
Device
V-supply Over-Voltage LU
Jedec/JESD78 Latch-up Level
LC4032ZE-TN48
> 1.5X V-supply @ 125°C
Class II
LC4064V-TN100
> 1.5X V-supply @ 105°C
Class II
LC4064B-TN100
> 1.5X V-supply @ 105°C
Class II
LC4064ZE-TN100B
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
LC4128ZE-TN144
B
> 1.5X V-supply @ 105°C
Class II
LC4128ZE-TN144
D
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
> 1.5X V-supply @ 105°C
Class II
LC4064ZE-TCN100
LC4128ZE-TN100
C
B
LC4128ZE-TCN100C
LC4128ZE-MN144
D
LC4128ZE-TCN144C
LC4256ZE-TN100
B
LC4256ZE-TN144
B
LC4256ZE-TCN144
C
> 1.5X V-supply @ 105°C
Class II
LC4256B-FN256
> 1.5X V-supply @ 125°C
Class II
LC4256V-FN256
> 1.5X V-supply @ 125°C
Class II
LC4384B-FN256
> 1.5X V-supply @ 125°C
Class II
LC4384V-FN256
> 1.5X V-supply @ 125°C
Class II
LC4512B-FN256
> 1.5X V-supply @ 125°C
Class II
LC4512V-FN256
> 1.5X V-supply @ 125°C
Class II
LC4512B-FT256
> 1.5X V-supply @ 105°C
Class II
LC4512V-FT256
> 1.5X V-supply @ 105°C
Class II
Latch up classification for Commercial/Industrial products, per JESD78
B: LC4064ZE- TN100, LC4128ZE-TN100 and LC4128ZE-TN144 and LC4256ZE-TCN144 from Seiko+UTAC: include 0.8mil diameter Au bond wire.
C: LC4064ZE-TCN100, LC4128ZE-TCN100, LC4128ZE-TCN144 and LC4256ZE-TCN144 bill-of-materials include Cu bond wires.
D: LC4128ZE-TN144/MN144, data is on UMC silicon.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
22
3.5 LA-ispMACH 4000V/Z Product Family – ESD and Latch UP Data (Automotive):
LA-ispMACH4000V Automotive Grade product family was tested and classified per the AEC-Q100002-Rev-D Human Body Model (HBM) Electrostatic Discharge (ESD) Test criteria and the JESD22A114C.01 Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) procedure.
All units were tested at 25oC and +125oC prior to reliability stress and after reliability stress. No
failures were observed within the passing classification.
Table 3.4.2 LA-ispMACH 4000 ESD-HBM Data (Automotive):
Device
HBM Passing Voltage
AEC-Q100-002 HBM Classification
LA4032V-TN44
> 2000 V
H2
LA4032ZC-TN48
> 2000 V
H2
LA4064V-TN100
> 2000 V
H2
LA4064ZC-TN100
> 2000 V
H2
LA4128V-TN100
> 2000 V
H2
LA4128ZC-TN100
> 2000 V
H2
LA4128V-TN144
> 2000 V
H2
HBM classification for Automotive products, per AEC-Q100-002-Rev-D
LA-ispMACH4000 Automotive Grade product family was tested and Classified per the AEC-Q100011-Rev-B, Charge Device Model (CDM) Electrostatic Discharge Test criteria and the JESD22C101C, Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand
Thresholds of Microelectronic Components procedure.
All units were tested at 25oC and +125oC prior to reliability stress and after reliability stress. No
failures were observed within the passing classification.
Table 3.4.4 LA-ispMACH 4000 ESD-CDM Data (Automotive):
Device
CDM Passing Voltage
AEC-Q100-011 Classification
LA4032V-TN44
> 1000V
C5
LA4032ZC-TN48
> 1000V
C5
LA4064V-TN100
> 1000V
C5
LA4064ZC-TN100
> 1000V
C5
LA4128V-TN100
> 750V
C4
LA4128ZC-TN100
> 750V
C4
LA4128V-TN144
> 750V
C4
CDM classification for Commercial/Industrial products, per AEC-Q100-011
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
23
LA-ispMACH4000V/ZC Automotive Grade product family was tested per the AEC-Q100-004-Rev-C,
IC Latch-up Test criteria and JEDEC EIA/JESD78 IC Latch-up Test procedure.
All units were tested at 25oC and +125oC prior to reliability stress and after reliability stress. No
failures were observed within the passing classification.
Table 3.4.7 LA-ispMACH4000 I/O Latch Up Data (Automotive):
Device
I/O Latch-up Results
Jedec/JESD78 Latch-up Level
LA4032V-TN44
+/- 100mA @ 125°C
Class II, Level A
LA4032ZC-TN48
+/- 100mA @ 125°C
Class II, Level A
LA4064V-TN100
+/- 100mA @ 125°C
Class II, Level A
LA4064ZC-TN100
+/- 100mA @ 125°C
Class II, Level A
LA4128V-TN100
+/- 100mA @ 125°C
Class II, Level A
LA4128ZC-TN100
+/- 100mA @ 125°C
Class II, Level A
LA4128V-TN144
+/- 100mA @ 125°C
Class II, Level A
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
24
4.0 PACKAGE QUALIFICATION DATA FOR ispMACH 4000 FAMILIES
The ispMACH 4000 product family is offered in ftBGA, csBGA, and TQFP packages. To cover the
range of die in the largest package types for this product family, different package and die
combinations were chosen as the generic qualification vehicles for all the package qualification tests
including, Temperature Cycling (T/C), Un-biased HAST (UHAST)and Biased HAST (BHAST).
Mechanical evaluation tests include Scanning Acoustic Tomography (SAT) and visual inspection.
The generation and use of generic data is applied across a family of products or packages emanating
from one base wafer foundry or assembly process is a Family Qualification, or Qualification By
Extension. For the package stresses BHAST and UHAST, these are considered generic for a given
Package Technology. T/C is considered generic up to an evaluated die size + package size + 10%, for a
given Package Technology. Surface Mount Pre-Conditioning (SMPC) is considered generic up to an
evaluated Peak Reflow temperature, for a given Package Technology. The following tables
demonstrate the package qualification matrix.
Table 4.1 ispMACH 4000 Product-Package Qualification-By-Extension Matrix
Product
LC4512V/B/C
LC4384V/B/C
LC4256V/B/C/
ZC/ZE
LC4128V/B/C/
ZC/ZE
LC4064V/B/C/
ZC/ZE
LC4032V/B/C/
ZC/ZE
Stress
Test
SMPC
T/C
BHAST
UHAST
* HTSL
SMPC
T/C
BHAST
UHAST
* HTSL
SMPC
T/C
BHAST
UHAST
* HTSL
SMPC
T/C
BHAST
UHAST
* HTSL
SMPC
T/C
BHAST
UHAST
* HTSL
SMPC
T/C
BHAST
UHAST
* HTSL
ASEM / ATK / UNISEM /UTAC Au-Wire Leaded Packages
44TQFP
48TQFP
100TQFP
128TQFP
144TQFP
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
MSL3
1k cyc
96 hrs
96 hrs
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
MSL3
1k cyc
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
MSL3
1k cyc
By Ext
By Ext
By Ext
Package
not
offered
176TQFP
MSL3
1k cyc
By Ext
By Ext
By Ext
MSL3
1k cyc
By Ext
By Ext
By Ext
MSL3
1k cyc
96 hrs
96 hrs
1k hrs
MSL3
1k cyc
By Ext
By Ext
By Ext
MSL3
1k cyc
96 hrs
96 hrs
1k hrs
MSL3
1k cyc
96 hrs
96 hrs
1k hrs
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
ASEM
ASEM / ATP /
UNISEM / UTAC
ASEM /
UTAC
64ucBGA
56csBGA
132csBGA
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
MSL3
1k cyc
By Ext
96 hrs
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
MSL3
1k cyc
96 hrs
96 hrs
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
256ftBGA
MSL3
1k cyc
96 hrs
96 hrs
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
ASEM /
ATP
** 256fpBGA
*
MSL3
1k cyc
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
By Ext
1k hrs
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
Package
not
offered
* Package HTSL stress run as HTRX (data retention). Both stresses are 1000 hour 150°C bakes.
** Package no longer offered. Use 256 ftBGA for all new designs. Refer to PCN#14A-07 for 256 fpBGA package discontinuance.
Note: All packages are qualified by an extension from the largest package and largest die in that package technology.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
25
Table 4.2 LA-ispMACH 4000 (Automotive) Product-Package Qualification-By-Extension
Matrix
ASEM / ATK Au-Wire Wire Leaded Packages
Product
Stress Test
44-TQFP
TN44
48-TQFP
TN48
100-TQFP
TN100
128-TQFP
TN128
SMPC
T/C
“V/ZC”
“V”
Package not
Package not
LA4128V/ZC
BHAST
Qualified by
Qualified by
offered
offered
extension
extension
UHAST
HTSL
SMPC
“V/ZC”
T/C
“V”
“V/ZC”
Qualified by
Package not
LA4064V/ZC
BHAST
Qualified by
Qualified by
extension
offered
extension
extension
UHAST
HTSL
1k hours
SMPC
T/C
“V”
“V/ZC”
Package not
Package not
LA4032V/ZC
BHAST
Qualified by
Qualified by
offered
offered
extension
extension
UHAST
HTSL
Note: All packages are qualified by an extension from the largest package and largest die in that package technology.
144-TQFP
TN144
MSL3/260C
1k cycles
96 hours
96 hours
By extension
Package not
offered
Package not
offered
Table 4.3 ispMACH 4000ZE Copper (Cu) Bond Wire Product-Package Qualification-ByExtension Matrix
ASEM / UTAC Cu-Wire Leaded Packages
Product
LC4256ZE
LC4128ZE
LC4064ZE
Stress Test
SMPC
T/C
BHAST
UHAST
HTSL
SMPC
T/C
BHAST
UHAST
HTSL
SMPC
T/C
BHAST
UHAST
HTSL
44-TQFP
TCN44
48-TQFP
TCN48
100-TQFP
TCN100
144-TQFP
TCN144
Package not
offered
Package not
offered
Qualified by
extension
MSL3/260C
1k cycles
96 hours
96 hours
1k hours
Package not
offered
Package not
offered
Qualified by
extension
Qualified by
extension
Qualified by
extension
Qualified by
extension
Package not
offered
Package not
offered
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
26
4.1 ispMACH 4000 Product Family Surface Mount Preconditioning Testing
The Surface Mount Preconditioning (SMPC) Test is used to model the surface mount assembly
conditions during component solder processing. All devices stressed through Temperature Cycling,
Un-biased HAST and Biased HAST were preconditioned. This preconditioning is consistent with
JEDEC JESD22-A113 “Preconditioning Procedures of Plastic Surface Mount Devices Prior to
Reliability Testing”, Moisture Sensitivity Level 3(MSL3) package moisture sensitivity and dry-pack
storage requirements.
Surface Mount Preconditioning (MSL3)
(10 Temperature Cycles between -55°C and 125°C, 24 hours bake @ 125°C, 30°C/60% RH, soak 192
hours, 225/245/250/260 °C Reflow Simulation, 3 passes) performed before all EE9 package tests.
MSL3 Packages: TQFP, fpBGA, ftBGA, csBGA, ucBGA
Surface Mount Preconditioning (MSL2)
(10 Temperature Cycles between -55°C and 125°C, 24 hours bake @ 125°C, 85°C/60% RH, soak 168
hours, 260°C Reflow Simulation, 3 passes) performed before all EE9 package tests.
MSL2 Packages: csBGA
Method: Lattice Procedure # 70-103467, J-STD-020 and JESD22-A113
Table 4.1.1 Surface Mount Precondition Data
Product Name
Package
Assembly
Site
Lot
Number
LC4032ZC
48 TQFP
Amkor
Lot #1
47
0
260°C
LC4032ZC
48 TQFP
Amkor
Lot #2
47
0
260°C
LC4032ZE
48 TQFP
Amkor
Lot #1
45
0
260°C
LC4032ZE
48 TQFP
Amkor
Lot #2
45
0
260°C
LC4064ZC
100 TQFP
Amkor
Lot #1
45
0
260°C
LC4064ZC
100 TQFP
Amkor
Lot #2
45
0
260°C
LC4064ZE
64 ucBGA
ASEM
Lot #1
154
0
260°C
LC4064ZE
64 ucBGA
ASEM
Lot #2
154
0
260°C
LC4128
128 TQFP
Amkor
Lot #1
45
0
260°C
LC4128
128 TQFP
Amkor
Lot #2
45
0
260°C
LC4256
176 TQFP
Amkor
Lot #1
135
0
260°C
LC4256
176 TQFP
Amkor
Lot #2
135
0
260°C
LC4256
176 TQFP
Amkor
Lot #3
135
0
260°C
LC4032
44 TQFP
ASEM
Lot #1
45
0
260°C
LC4064
44 TQFP
Amkor
Lot #1
45
0
260°C
LC4064
100 TQFP
Amkor
Lot #2
45
0
260°C
LC4128
128 TQFP
Amkor
Lot #1
45
0
260°C
LC4256
176 TQFP
Amkor
Lot #1
141
0
260°C
LC4256
176 TQFP
Amkor
Lot #2
141
0
260°C
LC4256
176 TQFP
Amkor
Lot #3
141
0
260°C
LC4256
256 fpBGA
Amkor
Lot #1
45
0
260°C
LC4384
176 TQFP
Amkor
Lot #1
45
0
260°C
Quantity # of Fails
Reflow
Temperature
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
27
Product Name
Package
Assembly
Site
Lot
Number
LC4512
176 TQFP
Amkor
Lot #1
45
0
260°C
LC4512
176 TQFP
Amkor
Lot #2
45
0
260°C
LC4256
132 csBGA
ASEM
Lot #1
100
0
240°C
LC4256
132 csBGA
ASEM
Lot #2
100
0
240°C
LC4256
132 csBGA
ASEM
Lot #3
100
0
240°C
LC4256
132 csBGA
ASEM
Lot #1
50
0
260°C
LC4256
132 csBGA
ASEM
Lot #2
50
0
260°C
LC4256
132 csBGA
Quantity # of Fails
Reflow
Temperature
ASEM
Lot #3
50
0
260°C
132 csBGA
A
ASEM
Lot #1
50
0
260°C
LC4256
132 csBGA
A
ASEM
Lot #2
50
0
260°C
LC4512
176 TQFP
ASEM
Lot #1
150
0
260°C
LC4512
176 TQFP
ASEM
Lot #2
150
0
260°C
LC4512
176 TQFP
ASEM
Lot #3
150
0
260°C
LC4512
176 TQFP
Amkor
Lot #1
150
0
260°C
LC4512
176 TQFP
Amkor
Lot #2
150
0
260°C
LC4512
176 TQFP
Amkor
Lot #3
150
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #1
120
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #2
120
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #3
120
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #4
167
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #5
167
0
260°C
LC45256ZC
132 csBGA
UNISEM
Lot #6
167
0
260°C
LC4064
44 TQFP
UNISEM
Lot #1
145
0
260°C
LC4064
44 TQFP
UNISEM
Lot #2
145
0
260°C
LC4064
44 TQFP
UNISEM
Lot #3
145
0
260°C
LC4512
176 TQFP
UNISEM
Lot #1
99
0
260°C
LC4512
176 TQFP
UNISEM
Lot #2
98
0
260°C
LC4512
176 TQFP
LC4256
UNISEM
Lot #3
75
0
260°C
256 ftBGA
C
ASEM
Lot #1
45
0
260°C
256 ftBGA
C
ASEM
Lot #2
45
0
260°C
256 ftBGA
C
ASEM
Lot #1
77
1
256 ftBGA
C
ASEM
Lot #2
77
0
260°C
256 ftBGA
C
UTAC
Lot #1
199
0
260°C
256 ftBGA
C
UTAC
Lot #2
199
0
260°C
isplSI 5384VE
256 ftBGA
C
UTAC
Lot #3
231
0
260°C
LA4128V
144 TQFP
ASEM
Lot #1
234
0
260°C
LA4128V
144 TQFP
ASEM
Lot #2
231
0
260°C
LA4128V
144 TQFP
ASEM
Lot #3
234
0
260°C
LA4128V
144 TQFP
Amkor
Lot #1
81
0
260°C
LA4128V
144 TQFP
Amkor
Lot #2
82
0
260°C
LCMXO2280
LCMXO2280
ispLSI 5384VE
isplSI 5384VE
isplSI 5384VE
isplSI 5384VE
B
260°C
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
28
Product Name
Package
Assembly
Site
Lot
Number
LA4128V
144 TQFP
Amkor
Lot #3
78
0
260°C
LA4128V
144 TQFP
Amkor
Lot #4
162
0
260°C
LA4128V
144 TQFP
Amkor
Lot #5
200
0
260°C
LA4128V
144 TQFP
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
Quantity # of Fails
Reflow
Temperature
Amkor
Lot #6
200
0
260°C
TN 144
D
UTAC
Lot #1
319
0
260°C
TN 144
D
UTAC
Lot #2
319
0
260°C
TN 144
D
UTAC
Lot #3
319
0
260°C
TCN 144
E
UTAC
Lot #1
319
0
260°C
TCN 144
E
UTAC
Lot #2
319
0
260°C
TCN 144
E
UTAC
Lot #3
319
0
260°C
A: MSL-2 packages
Cumulative SMPC Failure Rate = 1 / 9,167
B: Functional failure after SMPC CAR# 2700
C: The LCMXO2280 and ispLSI 5384VE were the qualification vehicles for ASEM & UTAC 256 ftBGA packages.
The other ASEM & UTAC Mach4K 256 ftBGA packages are qualified by extension.
D: The LC4256ZE, TN144 bill-of-materials includes 0.8mil Gold (Au) bond wires.
E: The LC4256ZE, TCN144 bill-of-materials includes 0.8mil Copper (Cu) bond wires.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
29
4.2 ispMACH 4000 Product Family Temperature Cycling Data
The Temperature Cycling test is used to accelerate those failures resulting from mechanical stresses
induced by differential thermal expansion of adjacent films, layers and metallurgical interfaces in the
die and package. Devices are tested at 25°C after exposure to repeated cycling between -55°C and
+125°C in an air environment consistent with JEDEC JESD22-A104 “Temperature Cycling”,
Condition B temperature cycling requirements. Prior to Temperature Cycling testing, all devices are
subjected to Surface Mount Preconditioning.
MSL3 Packages: TQFP, fpBGA, ftBGA, csBGA, ucBGA
Stress Duration: 1000 cycles
Stress Conditions: Temperature cycling between -55°C to 125°C
Method: Lattice Procedure # 70-101568 and JESD22-A104C
Table 4.2.1: Temperature Cycling Data
48 TQFP
Assembly
Site
Amkor
Lot
Number
Lot #1
47
250
Cycles
0
500
Cycles
0
1000
Cycles
0
48 TQFP
Amkor
Lot #2
47
0
0
0
LC4032ZE
48 TQFP
Amkor
Lot #1
45
0
0
0
LC4032ZE
48 TQFP
LC4064ZC
10 TQFP
Amkor
Lot #2
45
0
0
0
Amkor
Lot #1
45
0
0
0
LC4064ZC
LC4064ZE
100 TQFP
Amkor
Lot #2
45
0
0
0
64 ucBGA
ASEM
Lot #1
77
0
0
0
LC4064ZE
64 ucBGA
ASEM
Lot #2
77
0
0
0
LC4128
128 TQFP
Amkor
Lot #1
45
0
0
0
LC4128
128 TQFP
Amkor
Lot #2
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #1
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #2
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #3
45
0
0
0
LC4032
44 TQFP
Amkor
Lot #1
45
0
0
0
LC4064
100 TQFP
Amkor
Lot #2
45
0
0
0
LC4128
128 TQFP
Amkor
Lot #1
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #1
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #2
45
0
0
0
LC4256
176 TQFP
Amkor
Lot #3
45
0
0
0
LC4256
256 fpBGA
Amkor
Lot #1
45
0
0
0
LC4384
176 TQFP
Amkor
Lot #1
45
0
0
0
LC4512
176 TQFP
Amkor
Lot #1
45
0
0
0
LC4512
176 TQFP
Amkor
Lot #2
45
0
0
0
LC4256
132 csBGA
ASEM
Lot #1
50
0
0
0
LC4256
132 csBGA
ASEM
Lot #2
50
0
0
0
LC4256
132 csBGA
ASEM
Lot #3
48
0
0
0
LC4256
132 csBGA
ASEM
Lot #1
48
0
0
0
LC4256
132 csBGA
ASEM
Lot #2
50
0
0
0
LC4256
132 csBGA
ASEM
Lot #3
50
0
0
0
LC4256
132 csBGAA
ASEM
Lot #1
50
0
0
0
LC4256
A
ASEM
Lot #2
50
0
0
0
Product Name
Package
LC4032ZC
LC4032ZC
132 csBGA
Quantity
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
30
176 TQFP
Assembly
Site
ASEM
Lot
Number
Lot #1
50
250
Cycles
0
500
Cycles
0
1000
Cycles
0
LC4512
176 TQFP
ASEM
LC4512
176 TQFP
ASEM
Lot #2
50
0
0
0
Lot #3
50
0
0
0
LC4512
176 TQFP
Amkor
Lot #1
45
0
0
0
LC4512
LC4512
176 TQFP
Amkor
Lot #2
45
0
0
0
176 TQFP
Amkor
Lot #3
45
0
0
0
LC45256ZC
132 csBGA
UNISEM
Lot #1
120
0
0
0
LC45256ZC
132 csBGA
UNISEM
Lot #2
120
0
0
0
LC45256ZC
132 csBGA
UNISEM
Lot #3
120
0
0
0
LC4064
44 TQFP
UNISEM
Lot #1
45
0
0
0
LC4064
44 TQFP
UNISEM
Lot #2
45
0
0
0
LC4064
44 TQFP
UNISEM
Lot #3
45
0
0
0
LC4512
176 TQFP
UNISEM
Lot #1
50
0
0
0
LC4512
176 TQFP
UNISEM
Lot #2
49
0
0
0
Product Name
Package
LC4512
Quantity
LC4512
176 TQFP
UNISEM
Lot #3
45
0
0
0
LCMXO2280
256 ftBGAB
ASEM
Lot #1
45
0
0
0
LCMXO2280
256 ftBGA
B
ASEM
Lot #2
45
0
0
0
ispLSI 5384VE
256 ftBGAB
ASEM
Lot #1
76
0
0
0
isplSI 5384VE
256 ftBGA
B
ASEM
Lot #2
77
0
0
0
isplSI 5384VE
256 ftBGA
B
UTAC
Lot #1
77
0
0
0
isplSI 5384VE
256 ftBGAB
UTAC
Lot #2
77
0
0
0
isplSI 5384VE
256 ftBGA
B
UTAC
Lot #3
77
0
0
0
LA4128V
144 TQFP
ASEM
Lot #1
77
0
0
0
LA4128V
144 TQFP
ASEM
Lot #2
77
0
0
0
LA4128V
144 TQFP
ASEM
Lot #3
77
0
0
0
LA4128V
144 TQFP
Amkor
Lot #1
81
0
0
0
LA4128V
144 TQFP
Amkor
Lot #2
82
0
0
0
LA4128V
144 TQFP
Amkor
Lot #3
78
0
0
0
TN 144
C
UTAC
Lot #1
83
0
0
0
LC4256ZE
TN 144
C
UTAC
Lot #2
83
0
0
0
LC4256ZE
TN 144C
UTAC
Lot #3
83
0
0
0
LC4256ZE
TCN 144
D
UTAC
Lot #1
83
0
0
0
LC4256ZE
TCN 144D
UTAC
Lot #2
83
0
0
0
LC4256ZE
D
UTAC
Lot #3
83
0
0
0
LC4256ZE
A: MSL-2 packages
TCN 144
Cumulative Temp Cycle Failure Rate = 0 / 3,867
B: The LCMXO2280 and ispLSI 5384VE were the qualification vehicles for ASEM & UTAC 256 ftBGA packages.
The other ASEM & UTAC Mach4K 256 ftBGA packages are qualified by extension.
C: The LC4256ZE, TN144 bill-of-materials includes 0.8mil Gold (Au) bond wires.
D: The LC4256ZE, TCN144 bill-of-materials includes 0.8mil Copper (Cu) bond wires.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
31
4.3 ispMACH 4000 Product Family Unbiased HAST Data
Unbiased Highly Accelerated Stress Test (HAST) testing uses both pressure and temperature to
accelerate penetration of moisture into the package and to the die surface. The Unbiased HAST test is
designed to detect ionic contaminants present within the package or on the die surface, which can
cause chemical corrosion. Consistent JEDEC JESD22-A118, “Accelerated Moisture Resistance Unbiased HAST,” for which the conditions are 96 hour exposure at 130°C and 85% relative humidity.
Prior to Unbiased HAST testing, all devices are subjected to Surface Mount Preconditioning.
MSL3 Packages: TQFP, fpBGA, ftBGA, csBGA, ucBGA
Stress Duration: 96 Hrs
Stress Conditions: 130°C, 15psig, 85% RH
Method: Lattice Procedure # 70-104285 and JESD22-A118
Table 4.3.1: Unbiased HAST Data
Product Name
Package
Assembly
Site
Lot
Number
Quantity
# of
Fails
Stress
Duration
LC4064ZE
64 ucBGA
ASEM
Lot #1
77
0
96 Hrs
LC4064ZE
64 ucBGA
ASEM
Lot #2
77
0
96 Hrs
LC4256
176 TQFP
ASEM
Lot #1
45
0
96 Hrs
LC4256
176 TQFP
ASEM
Lot #2
45
0
96 Hrs
LC4256
176 TQFP
ASEM
Lot #3
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #1
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #2
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #3
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #4
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #5
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #6
45
0
96 Hrs
LC4512
176 TQFP
Amkor
Lot #1
45
0
96 Hrs
LC4512
176 TQFP
Amkor
Lot #2
45
0
96 Hrs
LC4512
176 TQFP
Amkor
Lot #3
45
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #1
50
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #2
50
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #3
50
0
96 Hrs
LC4512
176 TQFP
UNISEM
Lot #1
49
0
96 Hrs
LC4512
176 TQFP
UNISEM
Lot #2
49
0
96 Hrs
LC4512
176 TQFP
UNISEM
Lot #3
30
0
96 Hrs
256 ftBGA
A
UTAC
Lot #1
77
0
96 Hrs
256 ftBGA
A
UTAC
Lot #2
77
0
96 Hrs
isplSI 5384VE
256 ftBGA
A
UTAC
Lot #3
77
0
96 Hrs
LA4128V
144 TQFP
ASEM
Lot #1
77
0
96 Hrs
LA4128V
144 TQFP
ASEM
Lot #2
75
0
96 Hrs
LA4128V
144 TQFP
ASEM
Lot #3
77
0
96 Hrs
LA4128V
144 TQFP
Amkor
Lot #4
81
0
96 Hrs
LA4128V
144 TQFP
Amkor
Lot #5
100
0
96 Hrs
isplSI 5384VE
isplSI 5384VE
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
32
Product Name
Package
Assembly
Site
Lot
Number
Quantity
# of
Fails
Stress
Duration
LA4128V
144 TQFP
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
Amkor
Lot #6
100
0
96 Hrs
TN 144
B
UTAC
Lot #1
77
0
96 Hrs
TN 144
B
UTAC
Lot #2
77
0
96 Hrs
TN 144
B
UTAC
Lot #3
77
0
96 Hrs
TCN 144
C
UTAC
Lot #1
77
0
96 Hrs
TCN 144
C
UTAC
Lot #2
77
0
96 Hrs
TCN 144
C
UTAC
Lot #3
77
0
96 Hrs
Cumulative Unbiased HAST failure Rate = 0 / 2,175
A: The LCMXO2280 and ispLSI 5384VE were the qualification vehicles for ASEM & UTAC 256 ftBGA packages.
The other ASEM & UTAC Mach4K 256 ftBGA packages are qualified by extension.
B: The LC4256ZE, TN144 bill-of-materials includes 0.8mil Gold (Au) bond wires.
C: The LC4256ZE, TCN144 bill-of-materials includes 0.8mil Copper (Cu) bond wires.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
33
4.4 ispMACH 4000 Product Family THB: Biased HAST Data
Highly Accelerated Stress Test (HAST) testing uses both pressure and temperature to accelerate
penetration of moisture into the package and to the die surface. The Biased HAST test is used to
accelerate threshold shifts in the MOS device associated with moisture diffusion into the gate oxide
region as well as electrochemical corrosion mechanisms within the device package. Consistent with
JEDEC JESD A110-B “Highly-Accelerated Temperature and Humidity Stress Test (HAST)”, the
biased HAST conditions are with Vcc bias and alternate pin biasing in an ambient of 130°C and 85%
relative humidity. Prior to Biased HAST testing, all devices are subjected to Surface Mount
Preconditioning.
MSL3 Packages: TQFP, fpBGA, ftBGA, csBGA, ucBGA
Stress Conditions: Vcc= 1.95V/ 3.6V, 130°C / 85% RH, 15 psig
Stress Duration: 96 hours
Method: Lattice Procedure # 70-101571 and JESD22-A101B
Table 4.4.1: Biased HAST Data
Product Name
Package
Assembly
Site
Lot
Number
Quantity
# of
Fails
Stress
Duration
LC4256
176 TQFP
Amkor
Lot #1
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #2
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #3
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #1
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #2
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #3
45
0
96 Hrs
LC4256
132 csBGA
ASEM
Lot #1
45
0
96 Hrs
LC4256
132 csBGA
ASEM
Lot #2
45
0
96 Hrs
LC4256
132 csBGA
ASEM
Lot #3
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #1
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #2
45
0
96 Hrs
LC4256
176 TQFP
Amkor
Lot #3
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #4
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #5
45
0
96 Hrs
LC45256ZC
132 csBGA
UNISEM
Lot #6
45
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #1
50
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #2
50
0
96 Hrs
LC4064
44 TQFP
UNISEM
Lot #3
50
0
96 Hrs
256 ftBGA
B
UTAC
Lot #1
45
0
96 Hrs
256 ftBGA
B
UTAC
Lot #2
45
0
96 Hrs
isplSI 5384VE
256 ftBGA
B
LA4128V
LA4128V
isplSI 5384VE
isplSI 5384VE
A
UTAC
Lot #3
77
1
96 Hrs
144 TQFP
ASEM
Lot #1
80
0
96 Hrs
144 TQFP
ASEM
Lot #2
77
0
96 Hrs
LA4128V
144 TQFP
ASEM
Lot #3
80
0
96 Hrs
LA4128V
144 TQFP
Amkor
Lot #4
81
0
96 Hrs
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
34
Product Name
Package
Assembly
Site
Lot
Number
Quantity
# of
Fails
Stress
Duration
LA4128V
144 TQFP
Amkor
Lot #5
100
0
96 Hrs
LA4128V
144 TQFP
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
Amkor
Lot #6
100
0
96 Hrs
TN 144
C
UTAC
Lot #1
77
0
96 Hrs
TN 144
C
UTAC
Lot #2
77
0
96 Hrs
TN 144
C
UTAC
Lot #3
77
0
96 Hrs
TCN 144
D
UTAC
Lot #1
77
0
96 Hrs
TCN 144
D
UTAC
Lot #2
77
0
96 Hrs
TCN 144
D
UTAC
Lot #3
77
0
96 Hrs
Cumulative BHAST failure Rate EE9 = 1 / 1,972
A: Failed for open. CAR # 2699
B: The LCMXO2280 and ispLSI 5384VE were the qualification vehicles for ASEM & UTAC 256 ftBGA packages.
The other ASEM & UTAC Mach4K 256 ftBGA packages are qualified by extension.
C: The LC4256ZE, TN144 bill-of-materials includes 0.8mil Gold (Au) bond wires.
D: The LC4256ZE, TCN144 bill-of-materials includes 0.8mil Copper (Cu) bond wires.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
35
4.5 ispMACH 4000 Product Family High Temperature Storage Life (HTSL)
High Temperature storage test is typically used to determine the effect of time and temperature, under
storage conditions, for thermally activated failure mechanisms of solid state electronic devices. Units
were stressed per JESD22-A103C, High Temperature Storage Life. For the original ispMACH 4000
non-volatile based products, the HTRX and HTSL stress and test conditions condition were the same.
Therefore in many cases the HTSL test was covered by HTRX. Prior to HTSL testing, all devices are
subjected to Surface Mount Preconditioning.
The High Temperature Storage Life units were stressed at 150°C.
High Temperature Storage Life (HTSL) Conditions:
Stress Duration: 168, 500, 1000, 1500 hours.
Temperature: 150°C
Method: Lattice Document # 87-101925 and JESD22-A103C / JESD22-A117A
Table 3.2.2: High Temperature Storage Life Results
Product Name
Package
Assembler
Lot #
Qty
168 Hrs
Result
500 Hrs
Result
LA4064V
100 TQFP
ASEM
Lot #1
78
0
0
0
78,000
LA4064V
100 TQFP
ASEM
Lot #2
77
0
0
0
77,000
LA4064V
100 TQFP
ASEM
Lot #3
78
0
0
0
78,000
LA4064V
100 TQFP
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
LC4256ZE
1000 Hrs 1500 Hrs Cumulative
Result
Result
Hours
Amkor
Lot #2
79
0
0
0
TN 144
A
0
118,500
UTAC
Lot #1
83
0
0
0
83,000
TN 144
A
UTAC
Lot #2
83
0
0
0
83,000
TN 144
A
UTAC
Lot #3
83
0
0
0
83,000
TCN 144
B
UTAC
Lot #1
77
0
0
0
77,000
TCN 144
B
UTAC
Lot #2
77
0
0
0
77,000
TCN 144
B
UTAC
Lot #3
77
0
0
0
77,000
EE9 Cumulative HTSL Failure Rate = 0 / 792
EE9 Cumulative HTSL Device Hours = 831,500
A: The LC4256ZE, TN144 bill-of-materials includes 0.8mil Gold (Au) bond wires.
B: The LC4256ZE, TCN144 bill-of-materials includes 0.8mil Copper (Cu) bond wires.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
36
5.0 ispMACH 4000 Process Reliability Wafer Level Review
Several key fabrication process related parameters have been identified by the foundry that would
affect the Reliability of the End-Product. These parameters are tested during the Development Phase of
the Technology. Passing data (a 10yr lifetime at the reliability junction temperature) must be obtained
for three lots minimum for each parameter before release to production. Normal operating conditions
are defined in the Electrical Design Rules (EDR). These parameters are:
Hot Carrier Immunity (HCI): Effect is a reduction in transistor Idsat. Worst case is low temperature.
Time Dependent Dielectric Breakdown (TDDB): Transistor and capacitor oxide shorts or leakage.
Negative Bias Temperature Instability (NBTI): Symptom is a shift in Vth (also a reduction in Idsat).
Electromigration Lifetime (EML): Symptom is opens within, or shorts between, metal conductors.
Stress Migration (SM): Symptom is a void (open) in a metal Via due to microvoid coalescence. SM
is not an issue for the EE9 BEOL (etched Al lines, W plug Vias, SiO IMD).
Table 5.1 – Wafer Level Reliability Results for Seiko EE9 (180nm) Process Technology
Device
delta Ids
Celsius
Vgstress
Vds
TTF
LVN
-10%
25
Vd/2
2
5 lots>23yr
TDDB
Device
Celsius
Vg
Area
0.1% TTF
LVPwell
130
2
8000um²
5 lots>133yr
EML
Layer
Celsius
delta R
Jmax
M1
130
20%
M2
130
20%
M3
130
20%
M4
130
20%
M5
130
20%
.573mA/um²
.705mA/um²
.705mA/um²
.705mA/um²
1.233mA/um²
0.1%TTF
4 lots>41yr
4 lots>32yr
4
lots>33yr
4
lots>16yr
5 lots>15yr
HCI
Note: Reliability life times are based on listed temperature and used conditions. Detailed WLR test conditions are available upon request.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
37
Table 5.2 – Wafer Level Reliability Results for UMC EE9 (180nm) Process Technology
HCI
TDDB
EML
Device
delta Ids
Celsius
Vgstress
Vds
TTF
LVN
-10%
25
Vd/2
2
12
lots>15yr
LVP
-10%
25
0
-2
6
lots>1200yr
HVN
-10%
25
Vd/2
3.6
6
lots>28yr
Device
Celsius
Vg
Area
LVPwell
130
2
8000um²
0.1% TTF
6 lots>110000yr
LVNwell
130
-2
8000um²
6
lots>2300yr
HVPwell
130
3.6
8000um²
6
lots>76yr
6 lots>70yr
Layer
Celsius
delta R
Jmax
M1
130
+20%
M2
130
+20%
M3
130
+20%
M4
130
+20%
M5
130
+20%
.573mA/um²
.705mA/um²
.705mA/um²
.705mA/um²
1.233mA/um²
0.1%TTF
7 lots>70yr
6 lots>77yr
4
lots>65yr
4
lots>173yr
3
lots>316yr
HVNwell
130
-3.6
8000um²
Note: Reliability life times are based on listed temperature and used conditions. Detailed WLR test conditions are available upon request.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
38
6.0 ispMACH 4000V/B/C/ZC/ZE Soft Error Rate Data
Soft Error Rate (SER) testing is conducted to characterize the sensitivity of EECPLD storage and
device registered logic elements to High Energy Neutron and Alpha Particle radiation. Charge induced
by the impact of these particles can collect at sensitive nodes in the device, and result in changes in the
internal electrical states of the device. While these changes do not cause physical damage to the device,
they can cause a logical error in device operation.
All testing conforms to JEDEC JESD-89.
Table 6.1 ispMACH 4000 MEASURED FITs / Mb
Stress / Structure
Neutron
Alpha
REGISTERED LOGIC
0.6
N/A
EECLPD
0
0
Note: Detailed SER data is available upon request.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
39
7.0 ispMACH 4000 PACKAGE ASSEMBLY INTEGRITY TESTS
7.1 Wire Bond Shear Test
This procedure is used to measure the wire bond strength at the ball joints. Thirty bonds from a
minimum of five devices were used for Wire Bond Shear.
WIRE BOND SHEAR TEST RESULTS: All observations > 15 grams for TQFP and fTBGA.
The average measured bond shear results for TQFP were Cpk of > 3.7 and Ppk of > 3.7.
The average measured bond shear results for 256 ball ftBGA were Cpk of > 3.5 and Ppk of > 3.5
7.2 Wire Bond Pull
This procedure is used to measure the wire bond strength at the ball joints and stitch bonds.
For products evaluation thirty bonds from a minimum of five devices were used for and Wire Bond
Pull. Test conditions for these tests were 6 grams minimum for 1.0 mil gold wire
WIRE BOND PULL RESULTS: All observations >6 grams for TQFP and ftbGA packages tested.
The average measured wire bond pull results for TQFP were Cpk of > 2.0 and Ppk of > 2.1.
The average measured wire bond pull results for 256 ball ftBGA were Cpk of > 2.4 and Ppk of > 2.4.
7.3 Solderability
This procedure is used to evaluate the solderability of device terminals normally joined by a soldering
operation. An accelerated aging test is included in this test method, which simulates natural aging
under a combination of various storage conditions that have deleterious effects. Units are exposed to a
8 hour steam preconditioning followed a flux exposure for 7 seconds and a dip in Pb-free solder alloy
@ 245 °C ± 5°C for 5 seconds. Minimum of 22 leads from 3 devices per lot were tested with zero
failure acceptance.
No failures were observed for ispMACH 4000 devices in TQFP packages. All the tested units passed.
There was less than 5% pitting and dewetting on the solder covered area.
7.4 Physical Dimensions
Devices were measured using the appropriate Lattice Semiconductor case outline drawings.
The 10 devices of TQFP from 3 different lots were measured with no failures found. The calculated
Cpk on this small sample is Cpk > 9.6.
The 10 devices 256 ftBGA from 3 different lots were measured with no failures found. The calculated
Cpk on this small sample is Cpk > 2.0.
7.5 Solder Ball Shear
For the 256 ball ftBGA ten devices from three lots were tested. All units were exposed to two surface
mount reflow simulations. The 256 ball ftBGA package use a 0.40 mm barrier metal diameter. All ball
shear observations were > 800 grams. The average measured ball shear results for 256 ball ftBGA
packages post reflow stress were Cpk of >2.0.
Note: Mach4K 256 ftBGA packages are qualified by extension from MachXO and ispLSI devices.
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
40
8.0 ispMACH 4000 ADDITIONAL FAMILY DATA
Table 8.1: ispMACH 4000 Package Assembly Data – csBGA/ ftBGA
Package
Attributes /
Assembly Sites
Die Family
(Product Line)
Fabrication
Process
Technology
Package
Assemble Site
Package Type
Ball Counts
Die Preparation/
Singulation
Die Attach
Material
Mold Compound
Supplier/ID
Wire Bond
Material
Wire Bond
Methods
Substrate
Material
L/F Plating or
BGA Ball
Lead Finish
Marking
ASEM
Amkor
UNISEM
UTAC
ispMACH 4000
ispMACH 4000
ispMACH 4000
ispMACH 4000
EE9
(180nm CMOS)
EE9
(180nm CMOS)
EE9
(180nm CMOS)
Malaysia
Philippines
Singapore
Singapore
csBGA/ucBGA/
ftBGA
56/64/132/144/
256
csBGA/caBGA/
ftBGA
csBGA
csBGA/ftBGA
56/132/256/324
56/132
56/132/256
wafer saw, full cut
wafer saw, full cut
wafer saw, full cut
wafer saw, full cut
Ablebond 2100
Series
Sumitomo / G770
Series
Ablebond 2300
Series
Sumitomo / G770
Series
Ablebond 2100
Series
Sumitomo / G760
Series
Ablebond 2300
Series
Sumitomo / G770
Series
Gold (Au)
Gold (Au)
Gold (Au)
Gold (Au)
Thermosonic Ball
Thermosonic Ball
Thermosonic Ball
Thermosonic Ball
Bismaleimide
Triazine HL83X
Series
Sn96.5/Ag3.0/
Cu0.5
SnAgCu solder
ball
Bismaleimide
Triazine HL83X
Series
Sn95.5/Ag4.0/
Cu0.5
SnAgCu solder
ball
Bismaleimide
Triazine HL83X
Series
Sn96.5/Ag3.0/
Cu0.5
SnAgCu solder
ball
Bismaleimide
Triazine HL83X
Series
Sn95.5/Ag4.0/
Cu0.5
SnAgCu solder
ball
Laser
Laser
Laser
Laser
EE9
(180nm CMOS)
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
41
Table 8.2: ispMACH 4000 Package Assembly Data – Au-Wire TQFP
Package
Attributes /
Assembly Sites
Die Family
(Product Line)
Fabrication
Process
Technology
Package Assembly
Site
Package
Type
Pin
Count
Die Preparation/
Singulation
Die Attach
Material
Mold Compound
Supplier/ID
Wire Bond
Material
Wire Bond
Methods
Lead frame
Material
Lead Finish
Marking
ASEM
Amkor
UNISEM
UTAC
ispMACH 4000
ispMACH 4000
ispMACH 4000
ispMACH
4000ZE
EE9
(180nm CMOS)
EE9
(180nm CMOS)
EE9
(180nm CMOS)
EE9
(180nm CMOS)
Malaysia
Korea
Singapore
Singapore
TQFP
TQFP
TQFP
TQFP
44/48/100/144/176
44/48/100/144/176
44/48/100/128/144
100/144
wafer saw, full cut wafer saw, full cut wafer saw, full cut wafer saw, full cut
Ablebond 3230
Ablebond 3230
CRM1076NS
Ablebond 3230
Hitachi 9220HF
Series
KTMC 5700TQ
Series
Sumitomo G700
Series
CEL9510HF10-U
Gold (Au)
Gold (Au)
Gold (Au)
0.8mil Gold (Au)
Thermosonic Ball
Thermosonic Ball
Thermosonic
Bball
Thermosonic
Bball
Cu Alloy
Cu Alloy
Cu Alloy
Cu Alloy
Matte Sn
(annealed)
Matte Sn
(annealed)
Matte Sn
(annealed)
Matte Sn
(annealed)
Laser
Laser
Laser
Laser
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
42
Table 8.3: ispMACH 4000 Package Assembly Data – Cu-Wire TQFP
Package Attributes / Assembly Sites
Die Family (Product Line)
Fabrication Process Technology
Package Assembly Site
Package Type
Pin Count
Die Preparation/ Singulation
Die Attach Material
Mold Compound Supplier/ID
UTAC
ispMACH 4000ZE
EE9 (180nm CMOS)
Singapore
TQFP
100/144
wafer saw, full cut
Ablebond 3230
CEL8240HF10G
Wire Bond Material
0.8mil Copper (Cu)
Wire Bond Methods
Thermosonic Bball
Lead frame Material
Cu Alloy
Lead Finish
Marking
Matte Sn (annealed)
Laser
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
43
9.0 Revision History
Table 9.1: Lattice ispMACH 4000 V/B/C/ZC/ZE Product Family Qualification Summary revisions
Date
July 2003
Revision
A
Section
--3.1 HTOL &
4.0 Package
July 2008
B
August 2009
C
Whole
document
May 2011
July 2011
D
E
3.4 ESD/LU
3.1 HTOL
November
2011
F
4.0 Package
Qual Data
October 2012
G
3.4 ESD/LU
Change Summary
Initial document release.
Added Seiko LC4032ZE & LC4064ZE qual data
to this Product Family Qual Summary
New qualification summary reporting format. Also
added UMC and Seiko foundry WLR; SER data;
ESD/LU; and Package assembly integrity & BOM
Updated Seiko LC4064ZE HBM-ESD data
Added UMC LC4032ZE & LC4064ZE ELFR data
Added UTAC package qual for LC4000ZE:
TN144 bill-of-materials includes 0.8mil Gold (Au)
bond wires; and TCN144 bill-of-materials
includes 0.8mil Copper (Cu) bond wires.
Added UMC LC4128ZE HBM, CDM & LU data
Lattice Semiconductor Corporation
5555 NE Moore Court
Hillsboro, Oregon 97124 U.S.A.
Telephone: (503) 268-8000, FAX: (503) 268-8556
www.latticesemi.com
© 2012 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are listed at
www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The
specifications and information herein are subject to change without notice.
www.latticesemi.com
Lattice Semiconductor Corporation Doc. #25-105900 Rev. G
44