Load cell with amplifier DLRx L002 Features • Voltage (DLRU) or current output (DLRI) • Compact dimensions • For compression • Protection class IP 65 • Stainless steel Technical Data Standard capacities 0...500 N 0...1000 N 0...2000 N Output signal at FSR DLRU 0...10 V DLRI 4...20 mA Linearity Hysteresis 0,5% FS 0,5% FS 0...5000 N 0...10000 N < 0,1% FS Zero balance DLRU < 5 mV DLRI < 8 µA Reset-Input active Reset-Input inactive Reset-Pulse Reset time 5...33 VDC < 2 mA < 1 VDC > 1 ms < 5 ms Switching frequency 1000 Hz Signal polarity DLRU unipolar (compression +10 V) DLRI unipolar (compression 20 mA) Noise DLRU (0...5 kHz) < 5 mVpp DLRI (0...5 kHz) < 8 µApp < ±0,02% /K Bridge resistance Full bridge 350 Ω Isolation resistance > 3 GΩ Excitation DLRU 18...33 V DLRI 14...33 V Supply current DLRU < 60 mA DLRI < 90 mA – static load – dynamic load Breaking load 200% FS 100% FS 320% FS Protection class IP 65 FS = Full scale output 2.14 1.4542 .B CO/CL10 Cable length < 0,15% FS (after 30 min. with FS) Temperature effect span < ±0,03% /K Load cell material DLR P L002. Non-repeatability Temperature effect zero 5 m, shielded, PUR, (between amplifier and sensor) Order Code Creep error Compensated 0...+70 ˚C temperature range Operating temperature -20...+70 ˚C range Storage temperature range -40...+85 ˚C Technical Data Cable CL10 10 m cable length (5 m standard) Load transmission CO Compression (see drawing) Measuring range 150 210 220 250 310 0...500 N 0...1000 N 0...2000 N 0...5000 N 0...10000 N Combined error B 0,3% Connection 14C 5-pin connector series M12 x 1 Output U Voltage output 0...10 V I Current output 4...20 mA Accessories (not included in delivery) Cable between the amplifier and the control unit. Series 713 Connector female, control side, 5-pin, Part No. 10135462 M12 x 1 Connector female with cable, control side, 5-pin ESG 34CH0200G 5-pin (shielded) 2 m, PUR, (Part No. 11046264) ESG 34CH0500G 5-pin (shielded) 5 m, PUR, (Part No. 11046266) ESG 34CH1000G 5-pin (shielded) 10 m, PUR, (Part No. 10155587) www.baumer.com DLRx L002 Dimensions (mm) Load cell Amplifier DABx AD2T + ø 11 SR60 14 29 29 9 Connector S35A, 4-pin 14 M12 x1 4 26 9 30 27 30 27 4 40 40 SR60 M12 x1 ø 11 62,5 79 79 45° M5 x 6M5 / 8x(4x) 6 / 8 (4x) 45° 62,5 4 fixing screws M5, strength class 10.9 Installation torque 9 Nm ø 40 47 ø 40 ø 55 ø 47 ø 55 Electrical Connection DLRU DLRI 14C 14C Bridge Circuit EXC.+ 4 5 3 4 5 3 1 2 1 2 SIG.+ SIG.- Pin Pin 1 +VS 1 +VS 2 -VOUT 2 n.c. 3 GND 3 GND 4 +VOUT 4 +lOUT 5 Reset 5 Reset Housing EXC.- Housing Wiring DLRU DLRI 1 +VS F 1 +VS F 18 - 33VDC 3 GND 2 n.c. 2 -VOUT 4 +VOUT U 5 Reset 14 - 33VDC 3 GND RL 4 +IOUT ±10 V I 5 – 33 VDC www.baumer.com 5 Reset RL 4 – 20 mA 5 – 33 VDC 2.15 26 2