Packaging, Tape and Reel Information

Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
Packaging, Tape and Reel Information
DESCRIPTION
DEVICES PER TUBS
Optocouplers are available in plastic dual-in-line packages
(DIP), SOP packages, and in a surface-mount, gull-wing,
lead bend configuration. Optocouplers purchased in the
DIP configuration are shipped in tubes. Optocouplers
purchased in a gull-wing configuration can be shipped in
tubes or on carrier tape. This section provides stick
specifications, tape and reel specifications, and component
information.
TUBE SPECIFICATIONS
TYPE
UNITS/TUBE
TUBES/BOX
UNITS/BOX
DIP-16
25
40
1000
DIP-4
100
40
4000
DIP-6
50
40
2000
DIP-8
50
40
2000
HV, CNY64
40
50
2000
HV, CNY65
30
35
1050
HV, CNY66
25
35
875



Figure 1 shows the physical dimensions of transparent,
antistatic, plastic shipping tubes. Figure 2 shows tube safety
agency labeling and orientation information.
The following table lists the number of parts per tube.
Dimensions in millimeters
528 ± 0.2
330 ± 0.5
260 ± 0.5
200 ± 0.5
150 ± 0.5
125 ± 0.5
– 1.0
30 ± 0.5
B
VISHAY OPTOSEMICONDUCTOR MADE IN MALAYSIA ANTISTATIC
Detail B
Detail A
A
– 1.0
– 1.0
3 ± 0.5
– 1.0
380 ± 1
0.7 ± 0.5
13 x 10 = 130
12 ± 0.3
B
6.6 ± 0.3
Transparent rigid PVC
2.7 ± 0.2
R
0.
1
6°
4.4 ± 0.3
1.0 14 x
0.
5
11 ± 0.3
R
0.6 ± 0.1
10°
A
// 0.2 B
Detail A
Detail B
5.7 ± 0.15
17996
Section A - B
Not to scale
Fig. 1 - Shipping Tube Specifications for DIP Packages
Rev. 2.2, 06-Oct-11
Document Number: 83714
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
Dimensions in inches (millimeters)
0.46 ± 0.01
(11.5 ± 0.25)
0.344 ± 0.01
(8.6 ± 0.25)
Side view
scale: 4X
0.104 ± 0.01
(2.6 ± 0.25)
0.058 ± 0.008
(1.46 ± 0.19)
0.312 ref.
(7.8 ref.)
0.03 ± 0.005
(0.7 ± 0.13)
0.03 ± 0.01
(0.7 ± 0.25)
Top view
not to scale
ANTISTATIC
VISHAY OPTOSEMICONDUCTOR
4 (100)
22.4 ± 0.04
(558.8 ± 1)
17997
Fig. 2 - Shipping Tube Specifications for SOP Packages
TUBE SPECIFICATIONS FOR DIP AND HIGH ISOLATION VOLTAGE PACKAGES
15912
15915
Fig. 3 - DIP-6 N, G
Rev. 2.2, 06-Oct-11
Fig. 4 - DIP-4, -2, -16 N, G
Document Number: 83714
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
Top cover tape
Embossed carrier
Embossment
17998
15913
Fig. 5 - CNY64
Fig. 7 - Tape and Reel Shipping Medium
REELS
• As shown in figure 4, all reels contain standard areas for
the placement of ESD stickers and labels. Each reel also
has a tape slot in its core. The overall reel dimension is
13". Reels contain 1000 6 or 8 pin gullwing parts and
could have up to three inspection lots
ESD sticker
Tape slot
in core
330
(13")
15914
Fig. 6 - CNY65, 66
Regular, special
or bar code label
TAPE AND REEL SPECIFICATIONS
Surface-mounted devices are packaged in embossed tape
and wound onto 13" molded plastic reels for shipment, to
comply with Electronics Industries Association Standard
EIA-481, revision A, and International Electrotechnical
Commission standard IEC 60286.
17999
Fig. 8 - Tape and Reel Shipping Medium
Leaders and Trailers
The carrier tape and cover tape are not spliced. Both tapes
are one single uninterrupted piece from end to end, as
shown in figure 2. Both ends of the tape have empty pockets
meeting these requirements.
• Trailer end (inside hub of reel) is 200 mm minimum
• Leader end (outside of reel) is 400 mm minimum and
560 mm maximum
• Unfilled leader and trailer pockets are sealed
• Leaders and trailers are taped to tape and hub,
respectively, with masking tape
• All materials are static-dissipative
Rev. 2.2, 06-Oct-11
Document Number: 83714
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SINGLE CHANNEL SOIC8 OPTOCOUPLERS
Dimensions in millimeters (inches)
Selected SOIC8 optocouplers are available in tape and reel
format. To order surface mount IL2XXA optocoupler on tape
and reel, add a suffix “T” after the part number, i.e., IL207AT.
The tape is 12 mm wide on a 33 cm reel. There are
2000 parts per reel. Taped and reeled SOIC8-A
optocouplers conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
Pin 1 and
top of component
1.5 (0.059) min.
2 ± 0.05 (0.079 ± 0.002)
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.35 (0.014)
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
6.4 (0.252)
5.5 (0.216) 12.0 ± 0.3
(0.472 ± 0.012)
3.78 (0.149)
5.25
(0.205)
9.2 (0.36)
8.0 ± 0.1
(0.315 ± 0.004)
0.1 (0.004) max.
Embossment
Center lines
of cavity
18003
1.5 (0.059)
Direction of feed
Fig. 9
TAPE AND REEL PACKAGING FOR DUAL CHANNEL
(1)
SOIC8 OPTOCOUPLERS
Dimensions in millimeters (inches)
Selected dual SOIC8 optocouplers are available in tape and
reel format. To order surface mount ILD2XX optocoupler on
tape and reel, add a suffix “T” after the part number, i.e.,
ILD207T.
Note
(1) Select dual channel devices are available in the shorter SOIC-8
package and will be taped according to the single channel
taping specification

The tape is 16 mm and is wound on a 33 cm reel. There are
2000 parts per reel. Taped and reeled dual SOIC8
optocouplers conform to EIA-481-2 and IEC 60286-3.
Pin 1 and
top of component
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.3 (0.012) max.
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
6.6 (0.26)
7.5 ± 0.05
(0.300 ± 0.002)
16.0 ± 0.3
(0.630 ± 0.012)
3.8 (0.15)
6.35 (0.25)
13.3 (0.523)
8.0 (0.315)
0.1 (0.004) max.
Center lines
of cavity
Embossment
18004
1.5 (0.059)
Direction of feed
Fig. 10
Rev. 2.2, 06-Oct-11
Document Number: 83714
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 7
Dimensions in millimeters
Selected 4 pin optocouplers are available in tape and reel
format. To order a 4 pin optocoupler with option 7 on tape
and reel, add a suffix “T” after the part number,
SFH615A-3X007T.
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 4 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
10 pitch cumulative
tolerance on tape
± 0.2
2 ± 0.1
1.5 + 0.1
4 ± 0.1
0.35 ± 0.05
1.75 ± 0.1
7.5 ± 0.1
16 ± 0.3
5.05 ± 0.1
5.05 ± 0.1
4°
X
X
5°
Typ.
6.51
1.5 + 0.250
10.41 ± 0.1
12 ± 0.1
4.67 ± 0.1
3.71 ± 0.1
Section X-X
21579
R 0.76
Fig. 11
TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 9
Dimensions in millimeters
Selected 4 pin optocouplers are available in tape and reel
format. To order any SFH6xx6 optocoupler on tape and reel,
add suffix “T” after the part number, i.e., SFH6156-3T.
Pin 1 and
top of component
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 4 pin optocouplers
conform to EIA-481-2 and IEC60286-3.
4 ± 0.1
1.5 min.
2 ± 0.05
10 pitch cumulative
tolerance on tape
± 0.2
1.75 ± 0.1
0.3 max.
Top
cover
tape
10.2
7.5 ± 0.05
4.07
16 ± 0.3
5.05
13.3
12
0.1 max.
Center lines
of cavity
Embossment
18005
Ø 1.5
Direction of feed
Fig. 12
Rev. 2.2, 06-Oct-11
Document Number: 83714
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 9, 90° ROTATION
Dimensions in millimeters (inches)
Selected 4 pin optocouplers are available in tape and reel
format. To order any SFH6xx series optocoupler on tape
and reel with this orientation, add suffix “T1” after the part
number, i.e., SFH6156-5T1.
16.00 + 0.30, -0.10
(0.013 (0.0008), -0.0004)
The tape is 16 mm and is wound on a 33 cm reel. There are
2000 parts per reel. Taped and reeled 4 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
(0.157 ± 0.004)
2 ± 0.10
(0.079 ± 0.004)
1.75 ± 0.1
1.5 + 0.10, - 0.00 (0.069 ± 0.004)
(0.59 ± 0.004)
7.5 ± 0.01
(0.295 ± 0.004)
10.36 ± 0.10
0.408 ± 0.004
16 ± 0.3
(0.630 ± 0.012)
10.36 ± 0.10
0.408 ± 0.004
4°
8.0 ± 0.10
(0.315 + 0.004)
1.5 + 0.25, - 0.0
0.059 + 0.001, - 0.0
4.92 ± 0.10
0.194 ± 0.004
18401
Fig. 13
TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 8
Dimensions in millimeters
Selected 4 pin optocouplers are available in tape and reel
format. To order any SFH6xx series optocoupler on tape
and reel, add suffix “T” after the part number, i.e.,
SFH615A-4X018T.
The tape is 24 mm and is wound on a 33 cm reel. There are
2000 parts per reel. Taped and reeled 4 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
1.5 ± 0.1
4 ± 0.1
2 ± 0.1
1.75 ± 0.1
0.35 ± 0.05
11.5 ± 0.1
24 ± 0.3
12.10 ± 0.15
X
4°
8 ± 0.1
4.9 ± 0.35 (1)
X
1.5 + 0.25, - 0.0
8°
21831-1
(1)
4.1 ± 0.1
Section X-X
4.65 ± 0.15 in the case of the VO61X series
R 0.76
Fig. 14
Rev. 2.2, 06-Oct-11
Document Number: 83714
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SMD-6 OPTOCOUPLERS WITH OPTION 7
Dimensions in millimeters
Selected 6 pin optocouplers with option 7 are available in
tape and reel format. To order 6 pin optocoupler with option
7 on tape and reel, add a suffix “T” after the option, i.e.,
CNY17-3X007T.
Pi n 1 and top
of component
0.35
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 6 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
2 ± 0.05
1.5 min.
10 pitch cumulative
tolerance on tape
± 0.2
1.75 ± 0.1
Top
cover
tape
10.4
7.5 ± 0.05
16 ± 0.3
4.57
9
13.3
12
0.1 max.
Embossment
Center lines
of cavity
18006
Ø 1.5
Direction of feed
Fig. 15
TAPE AND REEL PACKAGING FOR SMD-6 OPTOCOUPLERS WITH OPTION 9
Dimensions in millimeters
Selected 6 pin optocouplers with option 9 are available in
tape and reel format. To order 6 pin optocoupler with option
9 on tape and reel, add a suffix “T” after the option, i.e.,
CNY17-3X009T.
Pin 1 and top
of component
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 6 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
1.5 min.
2 ± 0.05
10 pitch cumulative
tolerance on tape
± 0.2
1.75 ± 0.1
0.3 max.
Top
cover
tape
10.35
7.5 ± 0.05
16 ± 0.3
4.09
9.14
13.3
12
0.1 max.
18007
Embossment
Center lines
of cavity
Ø 1.5
Direction of feed
Fig. 16
Rev. 2.2, 06-Oct-11
Document Number: 83714
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SMD-8 OPTOCOUPLERS WITH OPTION 7
Dimensions in millimeters (inches)
Selected 8 pin optocouplers with option 9 are available in
tape and reel format. To order 8 pin optocoupler with option
7 on tape and reel, add a suffix “T” after the option, i.e.,
ILCT6-X007T.
Pin 1 and
top of component
0.35 (0.014)
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 8-pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
1.75 ± 0.1
(0.069 ± 0.004)
Top
cover
tape
10.41 (0.410)
7.5 ± 0.05 16.0 ± 0.3
(0.295 ± 0.002) (0.630 ± 0.012)
4.7 (0.185)
10.21
(0.402)
13.3 (0.523)
12.0 (0.472)
0.1 (0.004) max.
Embossment
Center lines
of cavity
18008
1.5 (0.059)
Direction of feed
Fig. 17
TAPE AND REEL PACKAGING FOR SMD-8 OPTOCOUPLERS WITH OPTION 9
Dimensions in millimeters (inches)
Selected 8-pin optocouplers with option 9 are available in
tape and reel format. To order 8 pin optocoupler with option
9 on tape and reel, add a suffix “T” after the option, i.e.,
ILCT6-X009T.
Pin 1 and
top of component
The tape is 16 mm and is wound on a 33 cm reel. There are
1000 parts per reel. Taped and reeled 8 pin optocouplers
conform to EIA-481-2 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.35 (0.014)
1.75 ± 0.1
(0.069 ± 0.004)
Top
cover
tape
10.2 (0.402)
7.5 ± 0.05 16.0 ± 0.3
(0.295 ± 0.002) (0.630 ± 0.012)
4.17 (0.164)
10.31
(0.406)
13.3 (0.523)
12.0 (0.472)
0.1 (0.004) max.
18009
Embossment
Center lines
of cavity
1.5 (0.059)
Direction of feed
Fig. 18
Rev. 2.2, 06-Oct-11
Document Number: 83714
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SMD-16 OPTOCOUPLERS WITH OPTION 7
Dimensions in millimeters (inches)
Selected 16 pin optocouplers with option 7 are available in
tape and reel format. To order 16 pin optocoupler with
option 7 on tape and reel, add a suffix “T” after the option,
i.e., ILQ-X007T.
Pin 1 and
top of component
The tape is 32 mm and is wound on a 33 cm reel. There are
750 parts per reel. Taped and reeled 16 pin optocouplers
conform to EIA-481 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.35 (0.014) max.
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
10.41 (0.410)
14.2 ± 0.05 32 (1.260)
(0.559 ± 0.002)
4.72 (0.186)
20.29
(0.799)
25.5 (1.004)
16.0 (0.630)
0.1 (0.004) max.
Embossment
18010
Center lines
of cavity
2.0 (0.079)
Direction of feed
Fig. 19
TAPE AND REEL PACKAGING FOR SMD-16 OPTOCOUPLERS WITH OPTION 9
Dimensions in millimeters (inches)
Selected 16-pin optocouplers with option 9 are available in
tape and reel format. To order 16 pin optocoupler with
option 9 on tape and reel, add a suffix “T” after the option,
i.e., ILQ1-X009T.
Pin 1 and
top of component
The tape is 32 mm and is wound on a 33 cm reel. There are
750 parts per reel. Taped and reeled 16 pin optocouplers
conform to EIA-481 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.35 (0.014)
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
10.19 (0.401)
14.2 ± 0.05 32 (1.260)
(0.559 ± 0.002)
4.30 (0.169)
20.24
(0.797)
25.5 (1.004)
16.0 (0.630)
0.1 (0.004) max.
18011
Embossment
Center lines
of cavity
2.0 (0.079)
Direction of feed
Fig. 20
Rev. 2.2, 06-Oct-11
Document Number: 83714
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR SOP-8 OPTOCOUPLERS
Dimensions in millimeters (inches)
Selected 8 pin 2 mm optocouplers are available in tape and
reel format. To order 8 pin 2 mm optocoupler on tape and
reel, add a suffix “T” after the part number.
Pin 1 and
top of component
The tape is 16 mm and is wound on a 33 cm reel. There are
2000 parts per reel. Taped and reeled 8 pin 2 mm
optocouplers conform to EIA-481 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.35 (0.014)
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
9.04 (0.356)
7.5 ± 0.05 16.0 ± 0.3
(0.295 ± 0.002) (0.630 ± 0.012)
2.77 (0.109)
6.05
(0.238)
13.3 (0.523)
12.0 (0.472)
0.1 (0.004) max.
Embossment
Center lines
of cavity
18012
1.5 (0.059)
Direction of feed
Fig. 21
TAPE AND REEL PACKAGING FOR SOT223/10 MINI-COUPLERS
Dimensions in millimeters (inches)
Selected 10 pin mini-couplers are available in tape and reel
format. To order surface mount optocoupler on tape and
reel, add a suffix “T” after the part number.
Pin 1 and
top of component
The tape is 16 mm and is wound on a 33 cm reel. There are
2000 parts per reel. Taped and reeled 10 pin mini-couplers
conform to EIA-481 and IEC 60286-3.
4 ± 0.1
(1.57 ± 0.004)
2 ± 0.05 (0.079 ± 0.002)
1.5 (0.059) min.
10 pitch cumulative
tolerance on tape
± 0.2 (0.008)
0.3 (0.012) max.
Top
cover
tape
1.75 ± 0.1
(0.069 ± 0.004)
7.29 (0.287)
7.5 ± 0.05 16.0 ± 0.3
(0.295 ± 0.002) (0.630 ± 0.012)
2.0 (0.079)
6.76
(0.266)
13.3 (0.523)
12.0 (0.472)
0.1 (0.004) max.
18013
Embossment
Center lines
of cavity
1.5 (0.059)
Direction of feed
Fig. 22
Rev. 2.2, 06-Oct-11
Document Number: 83714
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR TCMT4XXX SERIES
Dimensions in millimeters
2000 pcs/reel
1.75
Ø 1.55
2.6
2
4
0.3
technical drawings
according to DIN
specification
7.5
10.6
16
5°
Ø 1.6
12
7.4
2.2
Direction of pulling out
18427
Fig. 23
TAPE AND REEL PACKAGING FOR TCMT4XXXT0 SERIES
Dimensions in millimeters
2000 pcs/reel
1.75
Ø 1.55
2.6
4
2
0.3
technical drawings
according to DIN
specification
7.5
16
10.6
5°
12
Direction of pulling out
Ø 1.6
7.4
2.2
18427_1
Fig. 24
Rev. 2.2, 06-Oct-11
Document Number: 83714
11
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR TCMT1XXX SERIES
Dimensions in millimeters
Ø 1.55
1.75
technical drawings
according to DIN
specification
2.6
4
2
0.3
7.5
7.4
16
5°
Ø 1.6
2.95
8
2.2
Direction of pulling out
18428
Fig. 25
TAPE AND REEL PACKAGING FOR TCMT1XXXT3 SERIES
Dimensions in millimeters
Ø 1.55
4
2
2.95
2.6
0.3
1.75
technical drawings
according to DIN
specification
Pot cover tape
7.5
13.3
7.4
16
8
20951
Pin 1 and top of
component
2.2
Ø 1.6
Direction of feed
Fig. 26
Rev. 2.2, 06-Oct-11
Document Number: 83714
12
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING FOR TCLT PRODUCT SERIES (both SOP-4L and SOP-4L5)
Dimensions in millimeters
3000 pcs/reel
1.75
Ø 1.55
2.7
4
2
0.3
technical drawings
according to DIN
specification
7.5
10.6
16
5°
Ø 1.6
4.25
8
2.3
18429
Direction of pulling out
Fig. 27
TAPE AND REEL PACKAGING 4 PIN MINIFLAT FOR SFH690ABT, SFH690AT, SFH690BT, SFH690CT
Dimensions in millimeters (inches)
+ 0.3
0.318 - 0.1
(0.0125 ± 0.0012)
2.0 0 ± 0.05
(0.079 ± 0.002)
4.0 0 ± 0.1
(0.157 ± 0.004)
1.50 + 0.1
(0.059 + 0.004)
5.5 0 ± 0.05
+ 0.3
(0.216 ± 0.002) 12.00
- 0.1
+ 0.012
(0.472
)
- 0.004
Typ. 4.30
7.33 ± 0.1
(0.289 ± 0.004)
0.76 (0.030) R
18956
2
1
3
4
1.7 5 ± 0.1
(0.06 9 ± 0.0049)
4°
2.3 6 ± 0.1
(0.09 3 ± 0.004)
2.6 6 ± 0.1
(0.105 ± 0.004)
8°
8.0 0 ± 0.1
(0.315 ± 0.004)
1.50 + 0.25
(0.05 9 + 0.10)
4.7 2 ± 0.1
(0.18 6 ± 0.004)
Fig. 28
Rev. 2.2, 06-Oct-11
Document Number: 83714
13
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging, Tape and Reel Information
www.vishay.com
Vishay Semiconductors
TAPE AND REEL PACKAGING 4 PIN MINIFLAT, 180° ROTATION
Dimensions in millimeters (inches)
Selected 4 pin miniflats are available in tape and reel format
with the part rotated by 180°. To order this version, the
tape and reel suffix “T” is augmented by the numerial “3”
+0.3
0.318 - 0.1
(0.0125 ± 0.0012)
eg. SFH690BT3. The tape is 16 mm and is wound on a
33 cm reel. There are 2000 parts per reel.
2.0 0 ± 0.05
(0.07 9 ± 0.002)
4.0 0 ± 0.1
(0.157 ± 0.004)
1.50 + 0.1
(0.05 9 + 0.004)
5.50 ± 0.05
+ 0.3
(0.216 ± 0.002) 12.00
- 0.1
+ 0.012
(0.472
)
- 0.004
typ. 4.30
7.3 3 ± 0.1
(0.28 9 ± 0.004)
0.76 (0.030) R
18956_1
4
1
1.7 5 ± 0.1
(0.06 9 ± 0.0049)
3
2
4°
2.3 6 ± 0.1
(0.09 3 ± 0.004)
2.66 ± 0.1
(0.105 ± 0.004)
8°
8.00 ± 0.1
(0.315 ± 0.004)
1.50 + 0.25
(0.05 9 + 0.10)
4.7 2 ± 0.1
(0.18 6 ± 0.004)
Fig. 29
Rev. 2.2, 06-Oct-11
Document Number: 83714
14
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000