Application Note 4 NJG1108HA8 WLAN/WiMAX Application 4. 2.3~2.7GHz BAND APPLICATION 4-1 SUMMARY The characteristics of 2.3~2.7GHz band has evaluated as follows. The evaluation circuit structure and measured data are reviewed. 4-2-1 MEASURED DATA1 (DC) General conditions: VDD=VINV=2.7V, Ta=+25°C, Zs=Zl=50Ω Parameter Symbol Conditions Measurement Unit data Operating Voltage VDD 2.7 V Inverter Voltage VINV 2.7 V Control Voltage (High) VCTL(H) 1.85 V Control Voltage (Low) VCTL(L) 0 V 2.01 mA 0 uA Operating current IDD1 RF OFF, VCTL=1.85V Operating current IDD2 RF OFF, VCTL=0V Inverter current IINV1 RF OFF, VCTL=1.85V 28.7 uA Inverter current IINV2 RF OFF, VCTL=0V 7.9 uA Control current ICTL RF OFF, VCTL=1.85V 5.7 uA 4-2-2 MEASURED DATA2 (RF) General conditions: VDD=VINV=2.7V, VCTL=1.85V, fRF=2500MHz, Ta=+25°C, Zs=Zl=50Ω Measurement Unit Parameter Symbol Conditions data Small signal gain Gain Gain flatness Gflat Noise figure NF Pin at 1dB compression point Output 3rd order intercept point Input 3rd order intercept point fRF=2300~2700MHz Exclude PCB, Connector Losses (0.10dB) P-1dB(IN) OIP3 IIP3 f1=fRF, f2=fRF+100kHz, Pin=-30dBm f1=fRF, f2=fRF+100kHz, Pin=-30dBm 15.5 dB 1.2 dB 1.51 dB -11.4 dBm +17.8 dBm +2.1 dBm RF Input port VSWR VSWRi 1.72 RF Output port VSWR VSWRo 1.81 1 Application Note 4 NJG1108HA8 4-3 APPLICATION CIRCUIT (Top View) 3 GND L2 3.3nH RFOUT RFIN RF IN L4 5.6nH 4 C1 100pF RF OUT 2 L1 10nH L3 2.7nH C2 1000pF Bias Circuit GND VDD=2.7V VINV Logic Circuit 5 VINV=2.7V 1 C3 1000pF 6 VCTL VCTL=0V or 1.85V 4-4 PCB DESIGN (Top View) Parts List Parts ID L1~L4 VDD C1~C3 C2 L2 RF IN L1 Comment MURATA (LQP03T Series) MURATA (GRM03 Series) L3 L4 C1 RF OUT C3 VCTL VINV PCB (FR-4): t=0.2mm MICROSTRIP LINE WIDTH =0.4mm (Z0=50Ω) PCB SIZE=17.0mm x 17.0mm 2 Application Note 4 NJG1108HA8 4-5-1 Typical Characteristics Condition: Ta=+25oC, VDD=VINV=2.7V, VCTL=1.85V, Zs=Zl=50Ω S11, S22 S21, S12 VSWR Zin, Zout 3 Application Note 4 NJG1108HA8 4-5-2 Typical Characteristics S11, S22 (f=50MHz~20GHz) S21, S12 (f=50MHz~20GHz) k factor vs. frequency (VDD=VINV=2.7V, VCTL=1.85V) 20 k factor 15 10 5 0 0 5 10 15 20 frequency (GHz) 4 Application Note 4 NJG1108HA8 4-5-3 Typical Characteristics Gain, IDD vs. Pin Pout vs. Pin (VDD=VINV=2.7V, VCTL=1.85V, fRF=2450MHz) (VDD=VINV=2.7V, VCTL=1.85V, fRF=2450MHz) 20 5 18 Pout Gain (dB) -5 -10 -15 P-1dB(IN)=-11.4dBm -20 -30 -20 -10 0 5 14 IDD 12 3 8 2 4 -40 0 -30 -20 Pout, IM3 vs. Pin 10 OIP3, IIP3 vs. frequency 22 14 20 Pout 18 -20 OIP3 (dBm) Pout, IM3 (dBm) 0 (VDD=VINV=2.7V, VCTL=1.85V, df=100kHz, Pin=-30dBm) 20 -40 IM3 12 OIP3 10 16 8 14 6 12 IIP3 4 10 2 8 0 IIP3=+2.3dBm -80 -100 -40 -10 Pin (dBm) (VDD=VINV=2.7V, VCTL=1.85V, fRF=2450+2450.1MHz) -60 1 P-1dB(IN)=-11.4dBm Pin (dBm) 0 4 10 6 10 6 IIP3 (dBm) Pout (dBm) 7 Gain 16 0 -25 -40 8 IDD (mA) 10 -30 -20 -10 Pin (dBm) 0 10 6 2.38 2.4 2.42 2.44 2.46 2.48 2.5 -2 2.52 frequency (GHz) 5 Application Note 4 NJG1108HA8 4-5-4 Typical Characteristics NJG1108HA8 Gain,Isolation vs. frequency NJG1108HA8 Return Loss vs. frequency (f=1~4GHz) 30 10 -10 20 Gain (dB) Gain 0 -20 -10 -30 -20 -40 Reverse Isolation -30 -50 -40 1.5 2 2.5 3 3.5 (f=1~4GHz) 10 Output Return Loss 0 -10 Input Return Loss -20 -30 -60 1 Return Loss (dB) 0 Reverse Isolation (dB) 20 1 4 1.5 2 2.5 3 3.5 4 frequency (GHz) frequency (GHz) NJG1108HA8 Gain,NF vs. frequency (f=2.5~2.7GHz) 18 4.0 17 3.5 Gain (dB) 3.0 Gain 15 2.5 14 2.0 1.5 13 12 NF 1.0 0.50 11 10 2.3 Noise Figure (dB) 16 2.35 2.4 2.45 2.5 2.55 2.6 2.65 0.0 2.7 frequency (GHz) 6