LD-Series LD-Series ELECTRONIC DIMMER CONTROLS The LD-Series represents a dynamic breakthrough in dashboard technology, with its programmable circuitry, superior design, and unparalleled performance that affords seamless integration into most any dash panel. A variety of options, along with superior performance, functionality, and aesthetics assure compliance with the most stringent customer requirements. Key features include: robust design package with all components encased in switch housing, eliminating wire chafing, providing cost-savings as well; minimized electrical connections; IP67 sealing which prevents PCB degradation and eliminates short circuit potential. Superior heat dissipation is achieved with a heat sink mass which is over 50% larger than competitive products. Fully programmable circuitry lets the designer decide illumination levels and detent positions. EMC eliminates electrical “noise” and provides interference-free radio signals. Ease of assembly is accommodated with polarized integral connectors and an industry standard mounting hole. Product Highlights: 3 Choices for incremental dimming rates 12 or 24 Volts Laser Etched or Lens Illumination IP67 Sealing Typical Applications: On/Off-Highway Equipment Agricultural Equipment Construction Equipment Carling Technologies, Inc. 60 Johnson Avenue, Plainville, CT 06062 Email: [email protected] Application Support: [email protected] Phone: 860.793.9281 Fax: 860.793.9231 www.carlingtech.com 2 | LD-Series Electronic Dimmer Control - General Specifications Electrical Contact Rating Dielectric Strength .4VA @ 24VDC (MAX) resistive 15 amps, 125VAC 10 amps, 250VAC 20 amps, 4-14VDC 15 amps, 15-28VDC 1250 Volts RMS between pole to pole 3750 Volts RMS between live parts and accessible surfaces Insulation Resistance 50 Megaohms Initial Contact Resistance 10 milliohms max. @ 4VDC Life 100,000 cycles maintained, 50,000 cycles momentary at rated voltage and current Contacts 90/10 silver-nickel, silver tin-oxide, gold Terminals Brass or copper/silver plate .230 (5.84 mm) Quick Connect terminations standard. Mechanical Endurance .250,000 cycles minimum Physical Lighted Incandescent - rated 10,000 hours LED - rated 100,000 hours 1/2 life (LED is internally ballasted for voltages to 24 VDC) Seals Rocker, base & bracket are sealed Base Nylon 66 GF rated to 85°C with a flammability rating of 94V0 Rocker Nylon 66 Reinforced, rated to 105°C (modular lens). Locking rocker, standard rocker & paddle. Laser etching with a polycarbonate actuator LockAcetal Lens Polycarbonate rated at 100°C Bracket Nylon Zytel 1.970 Connector Nylon 66 rated at 85°C. Polarized .260 [6.60] Actuator Travel (Angular Displacement) .390 [9.91] 1.020 [25.91] 2 position 3 positions 26° 13° from center Environmental IP67 for above panel components of the actual switch, representing an index of protection as applied to electrical equipment in accordance with IEC 529, BS 5490, DIN 400 50 & NFC 20 010. Corrosion Mixed Flowing Gas MFG Class III per ASTM B-827 & B-845, Method H, with 3 years exposure Operating Temperature -40°C to + 85°C Vibration 1 Per Mil-Std 202F, Method 204D Test Condition A 0.06 DA or 10G’s 10- 500 Hz. Tested with VCH connector. Test criteria - No loss of circuit during test and pre and post test contact resistance Vibration 2 24-50 Hz 0.40 DA 50-2000 ±10 G’s peak Results Horizontal Axis 3-5 G’s max. Random 24 Hz 0.06 PSD-Gsq/Hz 60 Hz 0.50 100 Hz 0.50 200 Hz 0.025 2000 Hz 0.025 No loss of circuit during test; <10µ chatter. Shock Per Mil-Std 202F, Method 213B, Test Condition K @ 30G’s. Tested with VCH connector. Test criteria - No loss of circuit during test, pre, and post test contact resistance Salt Spray Per Mil-Std 202F, Method 101D, Test Condition A, 48 Hrs. Thermal Shock Per Mil-Std 202F, Method 107F, Test Condition A, -55°C to 85°C. Test criteria - pre and post test contact resistance Moisture Resistance Per Mil-Std 202F, Method 106F, Test Criteria - pre and post test contact resistance Mounting Specifications .867 [22.02] 1.734 [44.04] TEST CUT HOLE IN ACTUAL MATERIAL MOUNTING HOLE .100 [2.54] 2.265 [57.53] 3.055 [77.60] Panel Thickness Range Acceptable Panel Thickness .030 to .156 (.76mm to 3.96mm) Recommended: .030, .062, .093, .125 and .156 .230 X .031 [5.84 X .79] T1 BAT T2 OUTPUT (LOAD) T3 GROUND PADDLE STYLE ACTUATOR *Manufacturer reserves the right to change product specification without prior notice. 1.300 [33.02] Q.C. SELECTION GUIDE COMPANY SERIES .344 [8.74] 1.570 [39.88] Environmental PACKARD PART NO. WIRE GAGE AWG MM 2 12084590 3.0 12 Email: [email protected] PACKARD Application [email protected] 12 12052224 Support: 3.0 METRI-PACK 2.0-1.0 16-14 12015870 Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com 630 SERIES 1.0-.80 20-18 12015869 1.340 [34.04] 1.060 [26.92] TIN PLATED BRASS 12020035 12052222 22-18 (2 REQ'D) .80.-.50 (2 REQ'D) .50-.35 20-22 LD-Series Electronic Dimmer Control - Ordering Scheme, Dimensional Specifications | 3 4 5 6 7 Termination Illumination Illumination Bracket Color 3 Dimming Rate 3 A A FE 8 Actuator Style/ Color 9 Lens Color 9 & 10 LENS COLOR Z No Lens Clear White Amber 1 - B - 7 C 3 - D - 9 E 5A - 1 SERIES LD Electronic Dimmer Control 2 RATING 1 4A, 12 volts 2 10A, 12 volts A C 2A, 24 volts 5A, 24 volts 3 DIMMING RATE 1 30 - 100% 8 positions 5 10 - 100% 10 positions A 0 - 100% 11 positions 4 TERMINATION 1 .230 TABS (5.84 mm) Green G H J K - 12 Legend Orientation 13 Legend 2 Red Blue Lens Style MT Large Transparent NU Large Translucent PV Bar Transparent RW Bar Translucent - - Laser Etch 11 LEGEND #1 00 No legend FC Dim FE For legend options, visit us at carlingtech.com 12 LEGEND ORIENTATION 0 No legend 1 vertical (lamp 1 on top) 2 horizontal (lamp 1 on right) 3 vertical (lamp 1 on bottom) 5 & 6 ILLUMINATION No lamp S Red AmberGreen 12V LEDC N H 24V LEDD P J 1 FC 11 Legend 1 10 Lens Color Bright ORIENTATION 1 LAMP 1 LAMP 2 LAMP 2 ORIENTATION 4 2 Rating LAMP 1 LAMP 2 LAMP 2 7 BRACKET COLOR 1 1 Black 2 3 White Gray 8 ACTUATOR STYLE / COLOR 1 Laser Etched Black White Gray Red Rocker 3 ABCD Paddle4 J K M N LAMP 1 45-4ZQ 45-3ZQ ORIENTATION 3 13 LEGEND #2 00 No legend FC Dim FE For legend options, visit us at carlingtech.com Bright Notes: 1 Custom colors are available. Consult factory. .867 [22.02] 1.970 1.734 [44.04] .260 [6.60] .390 [9.91] 1.020 [25.91] TEST CUT HOLE IN ACTUAL MATERIAL MOUNTING HOLE .100 [2.54] 2.265 [57.53] 3.055 [77.60] Panel Thickness Range Acceptable Panel Thickness .030 to .156 (.76mm to 3.96mm) Recommended: .030, .062, .093, .125 and .156 .230 X .031 [5.84 X .79] T1 BAT T2 OUTPUT (LOAD) T3 GROUND PADDLE STYLE ACTUATOR Q.C. SELECTION GUIDE 1.300 [33.02] .344 [8.74] 1.570 [39.88] 1.340 [34.04] 1.060 [26.92] COMPANY SERIES PACKARD PART NO. PACKARD METRI-PACK 630 SERIES TIN PLATED BRASS 12084590 12052224 12015870 12015869 12020035 12052222 WIRE GAGE AWG MM 2 3.0 12 12 3.0 2.0-1.0 16-14 1.0-.80 20-18 22-18 (2 REQ'D) .80.-.50 (2 REQ'D) .50-.35 20-22 Email: [email protected] Application Support: [email protected] Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com LAMP 1 ORIENTATION 2 LD 3 5 1 C C 1 1 Series 4 | Notes Email: [email protected] Application Support: [email protected] Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com Reps & Contact | 5 Authorized Sales Representatives Click on the group name on the map below to find your local representative or visit www.carlingtech.com/findarep. « « Matera W. Canada Matera E. Canada MIDWEST DM Michigan TEMCO Northwest Alaska, Hawaii « NORTHERN Hanna Lind Ltd. Melody Emery Sierra Bridge Marketing Omega Limited Dy-tronix Inc. LD. Allen Norris DM Assoc East Pacent DM Assoc TSI North TSI WEST Signal Enterprises Luscombe Engineering Pinnacle Marketing Sunbelt Components « South America DM Mexico Mexico SOUTHEAST ProRep Solutions « Matrix LATIN AMERICA Americas Europe Middle East Africa Asia-Pacific Oceania About Carling Founded in 1920, Carling Technologies is a leading manufacturer of electrical and electronic switches and assemblies, circuit breakers, electronic controls, power distribution units, and multiplexed power distribution systems. With four ISO registered manufacturing facilities and technical sales offices worldwide, Carling Technologies Sales, Service and Engineering teams do much more than manufacture electrical components, they engineer powerful solutions! To learn more about Carling please visit www.carlingtech.com/company-profile. To view all of Carling’s environmental, quality, health & safety certifications please visit www.carlingtech.com/environmental-certifications Email: [email protected] Application Support: [email protected] Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com Worldwide Headquarters Carling Technologies, Inc. 60 Johnson Avenue, Plainville, CT 06062 Phone: 860.793.9281 Fax: 860.793.9231 Email: [email protected] Northern Region Sales Office: [email protected] Southeast Region Sales Office: [email protected] Midwest Region Sales Office: [email protected] West Region Sales Office: [email protected] Latin America Sales Office: [email protected] Asia-Pacific Headquarters Carling Technologies, Asia-Pacific Ltd., Kowloon, Hong Kong Phone: Int + 852-2737-2277 Fax: Int + 852-2736-9332 Email: [email protected] Shenzhen, China: [email protected] Shanghai, China: [email protected] Pune, India: [email protected] Kaohsiung, Taiwan: [email protected] Yokohama, Japan: [email protected] Europe | Middle East | Africa Headquarters Carling Technologies LTD 4 Airport Business Park, Exeter Airport, Clyst Honiton, Exeter, Devon, EX5 2UL, UK Phone: Int + 44 1392.364422 Fax: Int + 44 1392.364477 Email: [email protected] Germany: [email protected] France: [email protected] www.carlingtech.com REV_04_2016