J-CAP Series Highest Joules/cc Tantalum Solid Electrolytic Chip Capacitors with Conductive Polymer Electrode FEATURES • Highest Energy per volume • Conductive polymer electrode offers benign failure mode under recommended use conditions • Low ESR • Undertab terminations layout: - High Volumetric Efficiency - Low profile case sizes - High capacitance in smaller dimensions - Close positioning of several parts for efficient high density PCB layout • 3x reflow 260°C compatible LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • Power backup for SSDs (MLC, SLC, EFD, PCIe), battery-powered portable equipment, industrial alarms, smart power meters, and mobile devices. CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L±0.20 (0.008) W+0.20 (0.008) -0.10 (0.004) WP+0.50 (0.020) -0.10 (0.004) H max. WN±0.20 (0.008) AP+0.30 (0.012) -0.20 (0.008) AN+0.30 (0.012) -0.20 (0.008) L 1210 3528-10 3.50 (0.138) 2.80 (0.110) 1.00 (0.039) 2.10 (0.083) 2.10 (0.083) 1.15 (0.045) 1.35 (0.053) T 1210 3528-12 3.50 (0.138) 2.80 (0.110) 1.20 (0.047) 2.10 (0.083) 2.10 (0.083) 1.15 (0.045) 1.35 (0.053) X 2917 7343-15 7.30 (0.287) 4.30 (0.169) 1.50 (0.059) 3.25 ± 0.20 (0.128±0.008) 3.25 (0.128) 2.00 (0.079) 3.20 (0.126) Code EIA Code EIA Metric L±0.30 (0.012) W±0.30 (0.012) H max. W1±0.20 (0.008) – AP+0.30 (0.012) -0.20 (0.008) AN+0.30 (0.012) -0.20 (0.008) 3 2924 7361-15 7.30 (0.287) 6.00 (0.240) 1.50 (0.059) 4.75 (0.187) – 2.00 (0.079) 3.20 (0.126) 4 2924 7361-20 7.30 (0.287) 6.00 (0.240) 2.00 (0.079) 4.75 (0.187) – 2.00 (0.079) 3.20 (0.126) W1 dimension applies to the termination width for A dimensional area only. Under development MARKING L, T, X CASE 4 CASE AVX LOGO Polymer Polarity Band (Anode+) AVX LOGO Polymer Capacitance Value in pF 158 = 1500μF 158 J XXXXX Rated Voltage J = 6.3V Polarity Band (Anode+) L W 090215 Approved (mJ) L T X 3 4 3.3 4.7 14.9 – 32.7 Rated Voltage J = 6.3V ID Code W L Under development (mJ) 4.7 6.5 18.2 38.8 38.8 W H AP + S AN _ HOW TO ORDER TCN 4 Type XXXXX Case Size Polarity Band (Anode+) H W1 Capacitance Value in pF 156 = 15μF 156 J Lot Code Polarity Band (Anode+) W MAXIMUM ENERGY PER CASE SIZE Case Size See table above W1 WP AP + S AN _ WN 158 M 006 R 0055 Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Tolerance M = ±20% Rated DC Voltage 006 = 6.3Vdc 016 = 16Vdc 025 = 25Vdc 035 = 35Vdc 050 = 50Vdc Packaging R = Pure Tin 7" Reel ESR in mΩ 121 J-CAP Series Highest Joules/cc Tantalum Solid Electrolytic Chip Capacitors with Conductive Polymer Electrode TECHNICAL SPECIFICATIONS Technical Data: Capacitance Range: Capacitance Tolerance: Leakage Current DCL: Rated Voltage (VR) Surge Voltage (VS) Temperature Range: Reliability: +85ºC: +85ºC: All technical data relate to an ambient temperature of +25°C 4.7 μF to 1500 μF ±20% 0.1CV 6.3 16 25 35 50 8 21 33 46 65 -55°C to +105°C 1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance 60% confidence level CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF 4.7 10 22 33 47 Code 475 106 226 336 476 100 107 150 220 330 470 157 227 337 477 1000 108 1500 158 Rated Voltage DC to 85°C, [mJ] 6.3V (J) 16V (C) L(200)/T(200) [3.3] L(200)*/T(200) [4.7] L(200) [1.2] L(200)/T(200) [1.7] T(200)* [2.6] X(70) 4(70) 4(70) [14.9] [21.8] [32.7] 25V (E) 35V (V) T(200) [1.8] T(200) [3.9] T(200)* T(250)* X(100) [4.3] [6.5] [9.2] 3(70)* [19.6] 4(70) [29.3] 50V (T) 4(200)* X(100) 4(150)* 3(150)* [26.3] [18.2] [38.8] X(50) [5.4] 3(100)* [11.6] X(200)/4(55) 4(55) [17.4] Available Ratings, (ESR ratings in mOhms in brackets) [Energy in mJ] Engineering samples - please contact manufacturer *Codes under development - subject to change Note: Voltage ratings are minimum values. AVX reserves the right to supply higher ratings in the same case size, to the same reliability standards. 122 090215 J-CAP Series Highest Joules/cc Tantalum Solid Electrolytic Chip Capacitors with Conductive Polymer Electrode RATINGS & PART NUMBER REFERENCE AVX Part No. Case Size Cap (μF) Rated Voltage (V) Rated Temp. (ºC) Category Voltage Product Category (V) TCNL107M006#0200 TCNL157M006#0200 TCNT157M006#0200 TCNX477M006#0050 TCNX108M006#0200 TCN4108M006#0055 TCN4158M006#0055 L L T X X 4 4 100 150 150 470 1000 1000 1500 6.3 6.3 6.3 6.3 6.3 6.3 6.3 85 85 85 85 85 85 85 5 5 5 6.3 6.3 6.3 6.3 TCNL336M016#0200 TCNT336M016#0200 TCNT476M016#0200 TCNX157M016#0070 TCN4227M016#0070 TCN4337M016#0070 L T T X 4 4 33 33 47 150 220 330 16 16 16 16 16 16 85 85 85 85 105 85 16 16 16 16 16 16 TCNX476M025#0100 TCN4157M025#0070 X 4 47 150 25 25 105 85 25 25 TCNT475M035#0200 TCNT106M035#0200 TCNX476M035#0100 T T X 4.7 10 47 35 35 35 85 85 85 35 35 28 DCL (μA) Max. 6.3 Volt @ 85°C 105°C 60 105°C 90 105°C 90 85°C 282 85°C 600 85°C 600 85°C 900 16 Volt @ 85°C 85°C 52.8 85°C 52.8 85°C 75.2 85°C 240 105°C 352 85°C 528 25 Volt @ 85°C 105°C 117.5 85°C 375 35 Volt @ 85°C 85°C 16.5 85°C 35 105°C 165 DF % Max. ESR Max. (mΩ) @ 100kHz MSL Energy (mJ) ENERGY Energy/volume (mJ/cm3) Energy/area (mJ/cm2) 10 10 10 6 30 20 20 200 200 200 50 200 55 55 3 3 3 3 3 4 4 1.2 1.7 1.7 5.4 11.6 11.6 17.4 118 177 147 115 246 132 198 11.8 17.7 17.7 17.3 36.9 26.4 39.6 6 6 6 6 20 20 200 200 200 70 70 70 3 3 3 3 4 3 3.3 3.3 4.7 14.9 21.8 32.7 334 277 395 316 249 374 33.4 33.4 47.6 47.4 49.8 74.7 6 20 100 70 3 4 9.2 29.3 195 335 29.3 67.0 10 10 10 200 200 100 3 3 3 1.8 3.9 18.2 154 328 387 18.6 39.5 58.0 Energy is calculated by this formula (consider derating factor): Energy = ½ C x ((Vr x X)2 – Vx2) where C = Capacitance Vr = Rated Voltage X = Recommended derating factor Vx= 3V (invariable) Moisture Sensitivity Level (MSL) is defined according to J-STD-020. All technical data relates to an ambient temperature of +25ºC. Capacitance is measured at 120Hz, 0.5RMS with DC bias of 2.2 volts. DCL is measured at rated voltage after 5 minutes. ESR allowed to move up to 1.25 times catalog limit post mounting. For typical weight and composition see page 220. NOTE: AVX reserves the right to supply a higher voltage rating in the same case size, to the same reliability standards. RECOMMENDED DERATING Rated Voltage/ Operating Temp. ≤ 10V 16V ≥ 20V 090215 ≤ 85°C 105°C 90% 90% 80% 90% 80% 80% 123 J-CAP Series Highest Joules/cc Tantalum Solid Electrolytic Chip Capacitors with Conductive Polymer Electrode PRODUCT CATEGORY 105°C TEST Endurance Storage Life Humidity Temperature Stability Surge Voltage 105°C series (Temperature range -55ºC to +105ºC) Characteristics Visual examination no visible damage Determine after application of rated voltage for 2000 DCL 1.25 x initial limit +48/-0 hours at 85±2ºC and then leaving 1-2 hours at room temperature. Also determine after application of within +10/-20% of ΔC/C 105ºC temperature, category voltage for 2000 +48/-0 within +20/-30% of hours and then leaving 1-2 hours at room temperaDF 1.5 x initial limit ture. Power supply impedance to be ≤ 0.1Ω/V. ESR 2 x initial limit Visual examination no visible damage DCL 1.25 x initial limit 105ºC, 0V, 2000h within +10/-20% of ΔC/C within +20/-30% of DF 1.5 x initial limit ESR 2 x initial limit Visual examination no visible damage Determine after storage without applied voltage DCL 3 x initial limit at 65±2ºC and 95±2% relative humidity for 500 ΔC/C within +30/-20% of hours and then recovery 1-2 hours at room temperature. DF 1.5 x initial limit ESR 2 x initial limit Condition Step 1 2 3 4 5 6 Temperature°C +20±2 -55+0/-3 +20±2 +85+3/-0 +105+3/-0 +20±2 Duration(min) 15 15 15 15 15 15 Test temperature: 105ºC+3/0ºC Test voltage: Category voltage at 105ºC Surge voltage: 1.3 x category voltage at 105ºC Series protection resistance 1000±100Ω Discharge resistance: 1000Ω Number of cycles: 1000x Cycle duration: 6 min; 30 sec charge, 5 min 30 sec discharge DCL ΔC/C DF Visual examination +20ºC -55ºC IL* n/a n/a +0/-20% IL* 1.5 x IL* initial value for Ur ≤ 16V initial value for Ur ≥ 20V initial value for Ur ≤ 16V initial value for Ur ≥ 20V initial value +20ºC +85ºC +105ºC +20ºC IL* 10 x IL* 12.5 x IL* IL* ±5% +20/-0% +30/-0% ±5% IL* 1.5 x IL* 2 x IL* IL* no visible damage DCL initial limit ΔC/C within +10/-20% of initial value for Ur ≤ 16V within +20/-30% of initial value for Ur ≥ 20V DF 1.25 x initial limit *Initial Limit PRODUCT CATEGORY 85°C TEST Endurance Storage Life Humidity Temperature Stability Surge Voltage *Initial Limit 124 85°C series (Temperature range -55ºC to +85ºC) Characteristics Visual examination no visible damage DCL 1.25 x initial limit Determine after application of rated voltage for 2000 +48/-0 hours at 85±2ºC and then leaving 1-2 hours ΔC/C within +10/-20% of initial value for Ur ≤ at room temperature. Power supply impedance to be within +20/-30% of initial value for Ur ≥ ≤0.1Ω/V. DF 1.5 x initial limit ESR 2 x initial limit Visual examination no visible damage DCL 1.25 x initial limit 85ºC, 0V, 2000h ΔC/C within +10/-20% of initial value for Ur ≤ within +20/-30% of initial value for Ur ≥ DF 1.5 x initial limit ESR 2 x initial limit Visual examination no visible damage Determine after storage without applied DCL 5 x initial limit voltage at 65±2ºC and 95±2% relative ΔC/C within +40/-20% of initial value humidity for 500 hours and then recovery DF 1.5 x initial limit 1-2 hours at room temperature. ESR 2 x initial limit Step Temperature°C Duration(min) +20ºC -55ºC +20ºC +85ºC 1 +20±2 15 DCL IL* n/a IL* 10 x IL* 2 -55+0/-3 15 3 +20±2 15 ΔC/C n/a +0/-20% ±5% +20/-0% 4 +85+3/-0 15 DF IL* 1.5 x IL* IL* 1.5 x IL* 5 +20±2 15 Condition Test temperature: 85+3/0ºC Test voltage: Rated voltage Surge voltage: 1.3 x rated voltage Series protection resistance 1000±100Ω. Discharge resistance: 1000Ω Number of cycles: 1000x Cycle duration: 6 min; 30 sec charge, 5 min 30 sec discharge Visual examination 16V 20V 16V 20V +20ºC IL* ±5% IL* no visible damage DCL initial limit ΔC/C within +10/-20% of initial value for Ur ≤ 16V within +20/-30% of initial value for Ur ≥ 20V DF 1.25 x initial limit For use outside of recommended conditions and special request, please contact manufacturer. 090215