GLC65 Triple O/P Instructions

GLC65 MULTI-OUTPUT SERIES
INSTALLATION INSTRUCTIONS
DC POWER SUPPLIES INC.
2311 STATHAM PKWY
OXNARD, CA 93033 + 805-486-4565
Internet: www.condorpower.com
RATINGS:
Input: 100-240 V ac, 2.0 A, 50/60 Hz
Output:
Model
GLC65A
GLC65B
GLC65D
GLC65E
GLC65G
GLC65H
Notes:
1.
Volts
DC
+5
+5
+5
+5
+5
+3.3
Output #1
Convection
7A
7A
7A
7A
5A
5A
150
LFM
9A
9A
9A
9A
8A
8A
Volts
DC
12
15
24
24
3.3
5
Output #2
Convection
3A
2.5 A
1.5 A
1.5 A
4A
4A
150
LFM
5.0 A
4.0 A
2.5 A
2.5 A
5.0 A
6.0 A
Volts
DC
-12
-15
-12
12
12
12
Output #3
Convection
2.5 A
2.0 A
2.5 A
2.5 A
2.5 A
2.5 A
150
LFM
4A
3A
4A
4A
4A
3A
Models may or may not be followed by suffix –YYY and/or G, where YYY may be any number from 001 thru 999.
The –YYY suffix are used for value added configurations that have no impact on safety and suffix G indicates
compliance to RoHS.
Maximum 70 W total with a minimum of 150 LFM airflow over unit.
Maximum 60 W total convection cooled.
Maximum ambient temperature for rated output current is 50 °C.
Maximum Operating Relative Humidity 96 %, no condensation
Storage: -40 to +85 °C. Units should be allowed to warm-up under non-condensing conditions before application
of power.
2.
3.
4.
6.
7.
SAFETY DECLARATION: Condor DC Power Supplies, Inc. declares under our sole responsibility that all models listed
above are in conformity with the applicable requirements of EN 60950-1 following the provisions of the Low Voltage
Directive 73/23/EEC. All models are Certified to be in compliance with the applicable requirements of UL 60950., CSA
60950 (L3M1), EN 60950-1, and IEC 60950-1. They are certified for Pollution Degree 2 environment and Class I TN-S
power systems. All DC outputs are SELV under normal and single fault conditions.
TEMPERATURES: The maximum operating temperatures of components used in this supply must not be exceeded after installation.
The orientation of the supply, output power, ambient temperature and the availability, amount, direction and/or restriction of natural
airflow influences the temperatures of these components. Keeping the temperature of the core of T2 below 110 °C will usually be
sufficient to meet all other temperature requirements.
GROUNDING: The ground connection (quick connect tab) must be bonded to ground in the host equipment in order to meet the
specified EMC requirements. Using this terminal for safety grounding the host equipment is not recommended. A separate dedicated
grounding point should be used.
SPACINGS: The required creepage and clearance distances from primary circuits to ground
and secondary circuits must be maintained after installation to preserve the intended safety.
WARNING! RISK OF FIRE! A blown internal fuse is an indication of catastrophic failure
of circuit component(s). Refer to fuse marking on the power supply for type and rating. Repair
must be performed by Condor authorized personnel.
EXPLANATION OF SYMBOLS
Alternating Current
Direct Current
Attention, Consult
Accompanying Documents
Attention, Dangerous Voltages
WARNING! SHOCK HAZARD! Dangerous voltages are present on some components and
printed wiring traces.
Earth (Ground)
CONNECTIONS
J1 Pin
AC Input
J2 Pin
DC Output
MATING CONNECTORS
1
3
Line
Neutral
1
2
3
4
5
6
V2 Output
V1 Output
V1 Output
Return
Return
V3 Output
J1:
Amp Housing 640250-3; Pins 770476-1
J2:
Amp Housing 640250-6; Pins 770476-1
Condor DC Power Supplies Inc. will not be liable for the safety, reliability or performance of these power supplies if a) any changes, modifications or repairs are
carried out by other than authorized agents of Condor DC Power Supplies Inc., or b) the installation of the supply is not in accordance with these installation
instructions and the applicable UL, CSA, and IEC/EN safety standards.
41-34995-0001 Rev E 01/25/06