HA-2544/883 Video Operational Amplifier July 1994 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The HA-2544/883 is a fast, unity gain stable, monolithic op amp designed to meet the needs required for accurate reproduction of video or high speed signals. It offers high voltage gain (3.5kV/V min, 6kV/V typ), wide unity gain bandwidth of 45MHz minimum and phase margin of 65 degrees (open loop). Built from high quality Dielectric Isolation, the HA-2544/883 is another addition to the Intersil series of high speed, wideband op amps, and offers true video performance combined with the versatility of an op amp. • Wide Unity Gain Bandwidth . . . . . . . . . . . 45MHz (Min) • High Slew Rate . . . . . . . . . . . . . . . . . . . . . 100V/µs (Min) • Low Supply Current. . . . . . . . . . . . . . . . . . . 12mA (Max) • Differential Gain Error . . . . . . . . . . . . . . . . 0.04dB (Max) The primary features of the HA-2544/883, include wide bandwidth, 150V/µs (typ) slew rate, < 0.04dB differential gain error, < 0.11 degrees differential phase error and gain flatness of just 0.15dB at 3.58MHz and 4.43MHz, therefore proving to be sufficient for video amplification. High performance and low power requirements are met with a supply current of only 10mA typically and 12mA over the full temperature range. • Differential Phase Error. . . . . . . . . . . . . 0.11 Deg. (Max) • Gain Flatness at 3.58MHz or 4.43MHz . . . 0.15dB (Max) • Fast Settling Time (10V to 0.1%). . . . . . . . . 120ns (Typ) Applications • Video Systems Uses of the HA-2544/883 range from video test equipment guidance systems, radar displays and other precise imaging systems where stringent gain and phase requirements have previously been met with costly hybrids and discrete circuitry. The HA-2544/883 will also be used in non-video systems requiring high speed signal conditioning such as data acquisition systems, medical electronics, specialized instrumentation and communication systems. • Video Test Equipment • Radar Displays • Imaging Systems • Pulse Amplifiers • Signal Conditioning Circuits • Data Acquisition Systems Ordering Information PART NUMBER TEMPERATURE RANGE PACKAGE HA2-2544/883 -55oC to +125oC 8 Pin Can HA4-2544/883 -55oC to +125oC 20 Lead Ceramic LCC HA7-2544/883 -55oC 8 Lead CerDIP to +125oC Pinouts 3 V- 4 NC NC 1 NC BAL 2 NC 8 20 19 7 V+ NC 4 6 OUT -IN 5 NC 6 +IN 7 15 OUT NC 8 14 NC 5 BAL 18 NC 16 NC + 9 10 11 12 13 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 3-161 7 BAL 1 17 V+ - NC +IN + 3 BAL 2 NC V- -IN 8 NC 1 HA-2544/883 (METAL CAN) TOP VIEW NC BAL HA-2544/883 (CLCC) TOP VIEW NC HA-2544/883 (CERDIP) TOP VIEW + -IN 2 +IN V+ 6 OUT 5 3 BAL 4 VCASE TIED TO V- 511028-883 File Number 3699 File Number Specifications HA-2544/883 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 35V Differential Input Voltage (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . 6V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current (< 10% Duty Cycle) . . . . . . . . . . . . . . . . 40mA Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W Metal Can Package . . . . . . . . . . . . . . . . . 155oC/W 67oC/W Package Power Dissipation Limit at +75oC for TJ ≤ +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V VINCM ≤ 1/2 (V+ - V-) RL ≥ 2kΩ TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 10Ω, RLOAD = 500kΩ, CLOAD ≤ 10pF, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Input Offset Voltage SYMBOL VIO CONDITIONS VCM = 0V GROUP A SUBGROUPS 1 2, 3 Input Bias Current +IB -IB Input Offset Current Common Mode Range IIO +CMR VCM = 0V, +RS = 1kΩ, -RS = 10Ω VCM = 0V, +RS = 10Ω, -RS = 1kΩ VCM = 0V, +RS = 1kΩ, -RS = 1kΩ V+ = 5V, V- = -25V 1 V+ = 25V, V- = -5V +AVOL -AVOL Common Mode Rejection Ratio +CMRR -CMRR Output Voltage Swing +VOUT VOUT = 0V and +8V, RL = 1kΩ VOUT = 0V and -8V, RL = 1kΩ ∆VCM = +10V, V+ = +5V, V- = -25V, VOUT = -10V ∆VCM = -10V, V+ = +25V, V- = -5V, VOUT = +10V RL = 1kΩ RL = 1kΩ +25 C o o +125 C, -55 C o +25 C MIN MAX UNITS -15 15 mV -20 20 mV -15 15 µA -20 20 µA 1 +25oC -15 15 µA -20 20 µA o o o o 2, 3 +125 C, -55 C 1 +25oC -2 2 µA 2, 3 +125oC, -55oC -3 3 µA 1 +25oC 10 - V 10 - V - -10 V - -10 V 3.5 - kV/V 2.5 - kV/V 3.5 - kV/V 2.5 - kV/V 75 - dB 75 - dB 75 - dB 75 - dB 10 - V 10 - V - -10 V - -10 V 1 4 5, 6 4 5, 6 1 2, 3 1 2, 3 1 2, 3 -VOUT o +125 C, -55 C 2, 3 Large Signal Voltage Gain TEMPERATURE 2, 3 2, 3 -CMR LIMITS 1 2, 3 o o +125 C, -55 C o +25 C +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC Spec Number 3-162 511028-883 Specifications HA-2544/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±15V, RSOURCE = 10Ω, RLOAD = 500kΩ, CLOAD ≤ 10pF, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Output Current SYMBOL CONDITIONS +IOUT VOUT = -9V -IOUT Quiescent Power Supply Current +ICC ∆VSUP = 10V, V+ = +10V, V- = -15V, V+ = +20V, V- = -15V ∆VSUP = 10V, V+ = +15V, V- = -10V, V+ = +15V, V- = -20V +VIOAdj Note 1 -VIOAdj Note 1 MIN MAX UNITS o 25 - mA o - -25 mA - 12 mA - 12 mA o +25 C o 2, 3 +PSRR TEMPERATURE +25 C 1 VOUT = 0V, IOUT = 0mA LIMITS +25 C 1 VOUT = 0V, IOUT = 0mA -PSRR Offset Voltage Adjustment 1 VOUT = +9V -ICC Power Supply Rejection Ratio GROUP A SUBGROUPS o +125 C, -55 C o 1 +25 C -12 - mA 2, 3 +125oC, -55oC -12 - mA 1 +25oC 70 - dB o o 2, 3 +125 C, -55 C 70 - dB 1 +25oC 70 - dB o o 2, 3 +125 C, -55 C 70 - dB 1 +25oC VIO-1 - mV VIO+1 - mV o 1 +25 C NOTE: 1. Offset adjustment range is [VIO (Measured) ±1mV] minimum referred to output. This test is for functionality only to assure adjustment through 0V. 2. To achieve optimum AC performance, the input stage was designed without protective diode clamps. Exceeding the maximum differential input voltage results in reverse breakdown to the base-emitter junction of the input transistors and probable degradation of the input parameters especially VOS, IOS and Noise. TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 1kΩ, CLOAD = 10pF, VOUT = 1V/V, Unless Otherwise Specified. PARAMETERS Slew Rate SYMBOL +SR -SR CONDITIONS GROUP A SUBGROUPS VOUT = -3V to +3V VOUT = +3V to -3V 7 LIMITS TEMPERATURE MIN MAX UNITS o 100 - V/µs o 100 - V/µs +25 C 7 +25 C TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V, RLOAD = 1kΩ, CLOAD = 10pF, AV = 1V/V, Unless Otherwise Specified. LIMITS NOTES TEMPERATURE MIN MAX UNITS Differential Gain PARAMETERS dAV RS = 50Ω, RL = 1kΩ, fO = 3.58MHz and 4.43MHz 1, 5, 6, 8 +25oC - 0.04 dB Differential Phase d∅ RS = 50Ω, RL = 1kΩ, fO = 3.58MHz and 4.43MHz 1, 6, 8 +25oC - 0.11 Degrees Unity Gain Bandwidth Gain Flatness SYMBOL CONDITIONS UGBW VO = 200mVRMS, f at -3dB 1 +25oC 45 - MHz ∆AV VO = 200mVRMS, fO = 5MHz 1, 6 +25oC -0.15 0.15 dB VO = 200mVRMS, fO = 10MHz 1, 6 +25oC -0.35 0.35 dB Spec Number 3-163 511028-883 Specifications HA-2544/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Characterized at: VSUPPLY = ±15V, RLOAD = 1kΩ, CLOAD = 10pF, AV = 1V/V, Unless Otherwise Specified. LIMITS PARAMETERS SYMBOL Full Power Bandwidth FPBW CONDITIONS NOTES VPEAK = 1V CLSG Rise and Fall Time TR TF Overshoot +OS -OS Settling Time TS Output Resistance ROUT Quiescent Power Consumption PC o 1, 2 VPEAK = 5V Minimum Closed Loop Stable Gain TEMPERATURE +25 C o 1, 2 RL = 1kΩ, CL ≤ 1pF VOUT = 0V to +200mV VOUT = 0V to -200mV VOUT = 0V to +200mV VOUT = 0V to -200mV Open Loop +25 C o VOUT = 0V, IOUT = 0mA MAX UNITS 15.9 - MHz 3.2 - MHz o 1 -55 C to +125 C 1 - V/V 1, 4 +25oC 1, 4 - 15 ns o - 15 ns o - 20 % o - 20 % o - 150 % o +25 C 1 +25 C 1 +25 C 1 Open Loop MIN +25 C 1 +25 C - 40 Ω 1, 3 -55oC to +125oC - 360 mW NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.) 4. Measured between 10% and 90% points. 5. AD(%) = 10 A ( dB ) D ------------------------20 × 100 -1 6. The video parameter specifications will degrade as the output load resistance decreases. 7. C-L Gain and C-L Delay were less than the resolution of the test equipment used which is 0.1dB and 7ns, respectively. 8. Test signal used is 200mVRMS at each frequency on a 0 and 1 volt offset. For adequate test repeatability, a minimum warm-up of 2 minutes is suggested. TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLES 1 AND 2) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6, 7 Group A Test Requirements 1, 2, 3, 4, 5, 6, 7 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 3-164 511028-883 HA-2544/883 Die Characteristics DIE DIMENSIONS: 80 x 64 x 19 mils ± 1 mils 2030 x 1630 x 483µm ± 25.4µm METALLIZATION: Type: Al, 1% Cu Thickness: 16kÅ ± 2kÅ GLASSIVATION: Type: Nitride (Si3N4) over Silox (SIO2, 5% Phos.) Silox Thickness: 12kÅ ± 2kÅ Nitride Thickness: 3.5kÅ ± 1.5kÅ WORST CASE CURRENT DENSITY: 7.0 x 104 A/cm2 SUBSTRATE POTENTIAL (Powered Up): VTRANSISTOR COUNT: 44 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA-2544/883 BAL V+ -IN +IN OUT V- BAL All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 3-165 511028-883