HFA1145/883 June 1994 High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The HFA1145/883 is a high speed, low power current feedback amplifier built with Intersil’ proprietary complementary bipolar UHF-1 process. • Low Supply Current. . . . . . . . . . . . . . . . . . 5.9mA (Typ) This amplifier features a TTL/CMOS compatible disable control, pin 8, which when pulled low, reduces the supply current and forces the output into a high impedance state. This allows easy implementation of simple, low power video switching and routing systems. Component and composite video systems also benefit from this op amp’s excellent gain flatness, and good differential gain and phase specifications. • Wide -3dB Bandwidth . . . . . . . . . . . . . . . 360MHz (Typ) • High Slew Rate . . . . . . . . . . . . . . . . . . . . 1000V/µs (Typ) • Excellent Gain Flatness (to 50MHz) . . . . . ±0.07dB (Typ) • Excellent Differential Gain . . . . . . . . . . . . . 0.02% (Typ) • Excellent Differential Phase . . . . . . . . . 0.03 Deg. (Typ) • High Output Current . . . . . . . . . . . . . . . . . . 60mA (Typ) • Output Enable / Disable Time . . . . . . 180ns/35ns (Typ) Applications Multiplexed A/D applications will also find the HFA1145/883 useful as the A/D driver/multiplexer. The HFA1145/883 is a low power, high performance upgrade for the CLC410. Ordering Information • Multiplexed Flash A/D Driver PART NUMBER TEMPERATURE RANGE HFA1145MJ/883 -55oC to +125oC • RGB Multiplexers / Preamps for Multimedia Systems • Video Switching and Routing PACKAGE 8 Lead CerDIP • Pulse and Video Amplifiers • Wideband Amplifiers • RF/IF Signal Processing • Medical Imaging Systems Pinout HFA1145/883 (CERDIP) TOP VIEW NC 1 -IN 2 +IN 3 V- 4 + 8 DISABLE 7 V+ 6 OUT 5 NC CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 3-214 511116-883 File Number 3726 Spec Number Specifications HFA1145/883 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current (Note 1) . . . . . . . . . . . . . . . . Short Circuit Protected Output Current (50% Duty Cycle, Note 1) . . . . . . . . . . . . . . . . 60mA Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 2000V Storage Temperature Range . . . . . . . . . . . . . . -65oC ≤ TA ≤ +150oC Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . 115oC/W 30oC/W Maximum Package Power Dissipation at +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.87W Package Power Dissipation Derating Factor above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating VSUPPLY (±VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V Operating Temperature Range . . . . . . . . . . . . .-55oC ≤ TA ≤ +125oC RL ≥ 50Ω TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±5V, AV = +1, RF = 510Ω, RSOURCE = 0Ω, RL = 100Ω, VOUT = 0V, DIS = Floated, Unless Otherwise Specified. PARAMETERS Input Offset Voltage Common Mode Rejection Ratio Power Supply Rejection Ratio SYMBOL VIO CMRR PSRRP PSRRN Non-Inverting Input (+IN) Current +IN Current Common Mode Sensitivity +IN Resistance IBSP CMSIBP +RIN LIMITS GROUP A SUBGROUPS TEMPERATURE 1 +25oC -5 5 mV 2, 3 +125oC, -55oC -10 10 mV 1 +25oC 47 - dB 2 +125oC 44 - dB ∆VCM = ±1.2V V+ = 3.8V, V- = -6.2V V+ = 6.2V, V- = -3.8V 3 -55oC 44 - dB ∆VSUPPLY = ±1.8V V+ = 6.8V, V- = -5V V+ = 3.2V, V- = -5V 1 +25oC 50 - dB 2 +125oC 46 - dB ∆VSUPPLY = ±1.2V V+ = 6.2V, V- = -5V V+ = 3.8V, V- = -5V 3 -55oC 46 - dB ∆VSUPPLY = ±1.8V V+ = 5V, V- = -6.8V V+ = 5V, V- = -3.2V 1 +25oC 50 - dB 2 +125oC 46 - dB ∆VSUPPLY = ±1.2V V+ = 5V, V- = -6.2V V+ = 5V, V- = -3.8V 3 -55oC 46 - dB VCM = 0V 1 +25oC -15 15 µA 2, 3 +125oC, -55oC -25 25 µA ∆VCM = ±1.8V V+ = 3.2V, V- = -6.8V V+ = 6.8V, V- = -3.2V 1 +25oC - 1.25 µA/V 2 +125oC - 2.85 µA/V ∆VCM = ±1.2V V+ = 3.8V, V- = -6.2V V+ = 6.2V, V- = -3.8V 3 -55oC - 2.85 µA/V Note 2 1 +25oC 800 - kΩ 2, 3 +125oC, -55oC 350 - kΩ CONDITIONS VCM = 0V ∆VCM = ±1.8V V+ = 3.2V, V- = -6.8V V+ = 6.8V, V- = -3.2V MIN MAX Spec Number 3-215 UNITS 511116-883 Specifications HFA1145/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±5V, AV = +1, RF = 510Ω, RSOURCE = 0Ω, RL = 100Ω, VOUT = 0V, DIS = Floated, Unless Otherwise Specified. PARAMETERS +IN Current Power Supply Sensitivity SYMBOL PPSSIBP NPSSIBP Inverting Input (-IN) Current -IN Current Common Mode Sensitivity -IN Current Power Supply Sensitivity IBSN PPSSIBN NPSSIBN Output Voltage Swing VOP100 VON100 Output Voltage Swing VOP50 VON50 Output Current TEMPERATURE MIN MAX UNITS ∆VSUPPLY = ±1.8V V+ = 6.8V, V- = -5V V+ = 3.2V, V- = -5V 1 +25oC - 1 µA/V 2 +125oC - 3 µA/V ∆VSUPPLY = ±1.2V V+ = 6.2V, V- = -5V V+ = 3.8V, V- = -5V 3 -55oC - 3 µA/V ∆VSUPPLY = ±1.8V V+ = 5V, V- = -6.8V V+ = 5V, V- = -3.2V 1 +25oC - 1 µA/V 2 +125oC - 3 µA/V ∆VSUPPLY = ±1.2V V+ = 5V, V- = -6.2V V+ = 5V, V- = -3.8V 3 -55oC - 3 µA/V VCM = 0V 1 +25oC -7.5 7.5 µA CONDITIONS -25 25 µA ∆VCM = ±1.8V V+ = 3.2V, V- = -6.8V V+ = 6.8V, V- = -3.2V 1 +25oC - 6 µA/V 2 +125oC - 8 µA/V ∆VCM = ±1.2V V+ = 3.8V, V- = -6.2V V+ = 6.2V, V- = -3.8V 3 -55oC - 8 µA/V ∆VSUPPLY = ±1.8V V+ = 6.8V, V- = -5V V+ = 3.2V, V- = -5V 1 +25oC - 5 µA/V 2 +125oC - 8 µA/V ∆VSUPPLY = ±1.2V V+ = 6.2V, V- = -5V V+ = 3.8V, V- = -5V 3 -55oC - 8 µA/V ∆VSUPPLY = ±1.8V V+ = 5V, V- = -6.8V V+ = 5V, V- = -3.2V 1 +25oC - 5 µA/V 2 +125oC - 8 µA/V ∆VSUPPLY = ±1.2V V+ = 5V, V- = -6.2V V+ = 5V, V- = -3.8V 3 -55oC - 8 µA/V AV = -1 RL = 100Ω VIN = -3.2V 1 +25oC 3 - V AV = -1 RL = 100Ω VIN =+3.2V 1 +25oC VIN = +3V 2, 3 AV = -1 RL = 50Ω VIN = -2.7V 2, 3 CMSIBN +IOUT -IOUT LIMITS GROUP A SUBGROUPS AV = -1 RL = 50Ω VIN = -3V 2, 3 +125oC, +125oC, -55oC -55oC 2.8 - V - -3 V +125oC, -55oC - -2.8 V 1 +25oC 2.5 - V VIN = -2.25V 2 +125oC 2.0 - V VIN = -2.25V 3 -55oC 1.4 - V VIN = +2.7V 1 +25oC - -2.5 V VIN = +2.25V 2 +125oC - -2.0 V VIN = +2.25V 3 -55oC - -1.4 V 1 +25oC 50 - mA 2 +125oC 40 - mA 3 -55oC 28 - mA 1 +25oC - -50 mA 2 +125oC - -40 mA 3 -55oC - -28 mA Note 3 Note 3 Spec Number 3-216 511116-883 Specifications HFA1145/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±5V, AV = +1, RF = 510Ω, RSOURCE = 0Ω, RL = 100Ω, VOUT = 0V, DIS = Floated, Unless Otherwise Specified. PARAMETERS SYMBOL Quiescent Power Supply Current ICC CONDITIONS TEMPERATURE MIN MAX UNITS 1 +25oC 5.6 6.1 mA RL = 100Ω 2, 3 IEE Disabled Power Supply Current DISICC RL = 100Ω RL = 100Ω, VDIS = 0V Disabled Output Leakage Current DOLC Disable Input Current DILLC DILHC Disable Input Logic Levels RL = 100Ω, VDIS = 0V VDIS = 0V, _ VIN = ±2.5V, VOUT = + 2.5V VDIS = 0V VDIS = 5V DILLV DILHV +125oC, -55oC 5.2 6.5 mA 1 +25oC -6.1 -5.6 mA 2, 3 +125oC, -55oC -6.5 -5.2 mA 1 +25oC - 4 mA - 4 mA -4 - mA 2, 3 DISIEE LIMITS GROUP A SUBGROUPS +125oC, -55oC 1 +25oC 2, 3 +125oC, -55oC -4 - mA 1 +25oC -10 10 µA -10 10 µA 1 +25oC - 200 µA 2, 3 +125oC, -55oC - 200 µA 1 +25oC - 15 µA 2, 3 +125oC, -55oC - 15 µA 1 +25oC - 0.8 V 2, 3 +125oC, -55oC 2, 3 +125oC, -55oC - 0.8 V 1, 2 +25oC, +125oC 2.0 - V 3 -55oC 2.4 - V NOTES: 1. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output current must not exceed 30mA for maximum reliability. 2. Guaranteed from +IN Common Mode Rejection Test, by: +RIN = 1/CMSIBP . 3. Guaranteed from VOUT Test with RL = 50Ω, by: IOUT = VOUT/50Ω. TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Table 2 Intentionally Left Blank. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Table 3 Intentionally Left Blank. TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLE 1) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3 Group A Test Requirements 1, 2, 3 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 3-217 511116-883 HFA1145/883 Die Characteristics DIE DIMENSIONS: 59 x 58.2 x 19 mils ± 1 mils 1500 x 1480 x 483µm ± 25.4µm METALLIZATION: Type: Metal 1: AICu(2%)/TiW Thickness: Metal 1: 8kÅ ± 0.4kÅ Type: Metal 2: AICu(2%) Thickness: Metal 2: 16kÅ ± 0.8kÅ GLASSIVATION: Type: Nitride Thickness: 4kÅ ± 0.5kÅ SUBSTRATE POTENTIAL (Powered Up): Floating (Recommend Connection to V-) WORST CASE CURRENT DENSITY: TBD TRANSISTOR COUNT: 75 Metallization Mask Layout HFA1145/883 -IN V+ OUT +IN V- OPTIONAL GND (NOTE) NOTE: This pad is not bonded out on packaged units. Die users may set a GND reference, via this pad, to ensure the TTL compatibility of the DIS input when using asymmetrical supplies (e.g. V+ = 10V, V- = 0V). All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 3-218 511116-883