INTERSIL HIP7010P

HIP7010
ADVANCE INFORMATION
J1850 Byte Level Interface Circuit
August 1996
Features
Description
• Fully Supports VPW (Variable Pulse Width) Messaging
Practices of SAE J1850 Standard for Class B Data
Communications Network Interface
- 3-Wire, High-Speed, Synchronous, Serial Interface
• Reduces Wiring Overhead
• Directly Interfaces with 68HC05 and 68HC11 Style SPI
Ports
• 1MHz, 8-Bit Transfers Between Host and HIP7010
Minimize Host Service Requirements
• Automatically Transmits Properly Framed Messages
• Prepends SOF to First Byte and Appends CRC to Last
Byte
• Fail-Safe Design Including, Slow Clock Detection
Circuitry, Prevents J1850 Bus Lockup Due to System
Errors or Loss of Input Clock
• Automatic Collision Detection
• End of Data (EOD), Break, Idle Bus, and Invalid Symbol
(Noise/Illegal Symbols) Detection
• Supports In-Frame Responses with Generation of
Normalization Bits (NB) for Type 1, Type 2, and Type 3
Messages
• Wait-For-Idle Mode Reduces Host Overhead During
Non-Applicable Messages
• Status Register Flags Provide Information on Current
Status of J1850 Bus
• Serial I/O Pins are Active Only During Transfers - Bus
Available for Other Devices 95% of the Time
• TEST Pin Provides Built-in-Test Capabilities for
In-System Diagnostics and Factory Testing
• High Speed (4X) Receive Mode for Production and
Diagnostic Testing/Programming
• Operates with Wide Range of Input Clock Frequencies
• Power-Saving Power-Down Mode
• Full -40oC to +125oC Operating Range
• Single 3.0V to 6.0V Supply
The Intersil HIP7010, J1850 Byte Level Interface Circuit, is a
member of the Intersil family of low-cost multiplexed wiring
ICs. The integrated functions of the HIP7010 provide the
system designer with components key to building a “Class B”
multiplexed communications network interface, which fully
conforms to the VPW Multiplexed Wiring protocol specified
in the SAE J1850 Standard. The HIP7010 is designed to
interface with a wide variety of Host microcontrollers via a
standard three wire, high-speed (1MHz), synchronous, serial
interface. The HIP7010 automatically produces properly
framed VPW messages, prepending the Start of Frame
(SOF) symbol and calculating and appending the CRC
check byte. All circuitry needed to decode incoming messages, to validate CRC bytes, and to detect Breaks, End of
Data (EOD), Idle bus, and illegal symbols is included. InFrame Responses (IFRs) are fully supported for Type 1,
Type 2, and Type 3 messages, with the appropriate Normalization Bit automatically generated. The HCMOS design
allows proper opeSration at various input frequencies from
2MHz to 12MHz. Connection to the J1850 Bus is via a Intersil HIP7020.
Ordering Information
TEMP.
PART NUMBER RANGE (oC)
PACKAGE
HIP7010P
-40 +125
14 Lead Plastic DIP
HIP7010B
-40 +125
14 Lead Plastic SOIC (N)
PKG. NO.
E14.3
M14.15
Pinout
HIP7010 (SOIC, PDIP)
TOP VIEW
IDLE 1
14 RDY
VPWIN 2
13 STAT
VPWOUT 3
12 CLK
VDD 4
11 VSS
RESET 5
10 SIN
9 SOUT
TEST 6
8 SCK
SACTIVE 7
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
File Number
3644.2
HIP7010
Block Diagram
LSB
10
SIN
A
B MUX
C
MSB
OUTPUT DATA
3
DATA SHIFT REGISTER
DECODED VPW IN
VPWOUT
J1850 VPW SYMBOL
ENCODER/DECODER
2
VPWIN
9
SOUT
A
MUX
B
STATUS/CONTROL BYTE
CRC GENERATOR/CHECKER
SCK
IDLE
RDY
STAT
8
1
14
13
STATE MACHINE
AND CONTROL LOGIC
TIMING
GENERATOR
12
CLK
RESET
TEST
SACTIVE
5
6
7
VDD 4
VSS 11
Pin Description
PIN NUMBER
PIN NAME
IN/OUT
PIN DESCRIPTION
1
IDLE
OUT
2
VPWIN
IN
3
VPWOUT
OUT
CMOS Output
4
VDD
-
Power Supply
5
RESET
IN
CMOS Schmitt (No VDD Diode)
6
TEST
IN
CMOS Input with Pull-Down
7
SACTIVE
OUT
CMOS Output
8
SCK
OUT
Three-State with Pull-Down
9
SOUT
OUT
Three-State with Pull-Down
10
SIN
IN
CMOS Input with Pull-Down
11
VSS
-
12
CLK
IN
CMOS Schmitt (No VDD Diode)
13
STAT
IN
CMOS Input with Pull-Down
14
RDY
IN
CMOS Input with Pull-Down
CMOS Output
CMOS Schmitt (No VDD Diode)
Ground
2
HIP7010
Absolute Maximum Ratings
Thermal Information
Supply Voltage (VDD) . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +7.0V
Input or Output Voltage
Pins with VDD Diode . . . . . . . . . . . . . . . . . . . .-0.3V to VDD +0.3V
Pins without VDD Diode . . . . . . . . . . . . . . . . . . . . -0.3V to +10.0V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2500 Gates
Thermal Resistance
θJA
Plastic DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . .+100oC/W
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+120oC/W
Maximum Package Power Dissipation at +125oC
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mW
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mW
Operating Temperature Range (TA) . . . . . . . . . . . -40oC to +125oC
Storage Temperature Range (TSTG). . . . . . . . . . . -65oC to +150oC
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC
Lead Temperature (Soldering, 10s). . . . . . . . . . . . . . . . . . . . +265oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +3.0V to +5.5V
Operating Temperature Range . . . . . . . . . . . . . . . . -40oC to +125oC
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V
Electrical Specifications
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .(0.8VDD) to VDD
Input Rise and Fall Time
CMOS Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100ns Max
CMOS Schmitt Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited
TA = -40oC to +125oC, VDD = 5VDC ±10%, Unless Otherwise Specified
PARAMETERS
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
-
1.0
5.0
mA
Supply Current
Operating Current
Power-Down Mode (Note 1)
Clock Stopped (Note 2)
IOP
CLK = 2.0 MHz
IPD
PD = 1
-
50
150
µA
CLK = VSS or VDD
-
5.0
50
µA
0.7VDD
-
VDD
V
0.8VDD
-
VDD
V
VSS
-
0.3VDD
V
VSS
-
0.2VDD
V
-1
0.001
1
µA
100
200
500
µA
ISTOP
Input High Voltage
CMOS Level (SIN, STAT, RDY, TEST)
VIH
Schmitt Trigger (RESET, CLK, VPWIN)
Input Low Voltage
CMOS Level (SIN, STAT, RDY, TEST)
VIL
Schmitt Trigger (RESET, CLK, VPWIN)
High Level Input Current
(CLK, VPWIN, RESET)
IIH
VIN = VDD
Input Buffer with Pull-Down (SIN, TEST, STAT, RDY)
Low Level Input Current
(CLK, VPWIN, RESET)
IIL
VIN = VSS
Input Buffer with Pull-Down (SIN, TEST, STAT, RDY)
-1
-0.001
1
µA
-10
-0.01
10
µA
Output High Voltage
(SCK, SOUT, VPWOUT, IDLE, SACTIVE)
VOH
ILOAD = 0.8 mA
VDD-0.8
-
-
V
VOL
ILOAD = -1.6 mA
-
-
0.4
V
IOZ
VOUT = VDD
100
200
500
µA
VOUT = VSS
-10
10
µA
0.5
2.0
V
Output Low Voltage
(SCK, SOUT, VPWOUT, IDLE, SACTIVE)
High Impedance Leakage Current
Three-State with Pull-Down (SCK, SOUT)
Schmitt Trigger Hysteresis Voltage
(RESET, CLK, VPWIN)
VHYS
0.2
NOTES:
1. SIN, STAT, RDY, and TEST = VSS; SACTIVE, SCK, and SOUT unconnected; VPWIN = VDD ; CLK = 10MHz.
2. SIN, STAT, RDY, and TEST = VSS ; SACTIVE, SCK, and SOUT unconnected; VPWIN = VDD; PD = 1.
3
HIP7010
Serial Interface Timing
NUMBER
SYMBOL
-
-
-
-
(1)
tCYC
(2)
tLEAD
(3)
tLAG
(See Figure 1- Figure 7) TA = -40oC to +125oC, VDD = 5VDC ±10%, Unless Otherwise Specified
PARAMETERS
MIN
TYP
MAX
UNITS
Operating Frequency
2
8
12
MHz
Input CLK Duty Cycle
40
50
60
%
-
1.0
-
MHz
Before Status/Control Transfer
450
750
850
ns
Before Data Transfer
1150
1225
1300
ns
After Status/Control Transfer
650
750
850
ns
After Data Transfer
1250
1300
1400
ns
SCK Cycle Time
SACTIVE Lead Time
SACTIVE Lag Time
(4)
tSCKH
Clock (SCK) HIGH Time
450
500
550
ns
(5)
tSCKL
Clock (SCK) LOW Time
450
500
550
ns
(6)
tDVSCK
Required Data In Setup Time (SIN to SCK)
-
10
50
ns
(7)
tSCKDX
Required Data In Hold Time (SIN after SCK)
-
-10
40
ns
(8)
tDZDA
Data Active from High Impedance Delay (SACTIVE to SOUT Active)
-10
10
-
ns
(9)
tDADZ
Data Active to High Impedance Delay (SACTIVE to SOUT High
Impedance)
-
10
40
ns
(10)
tDVSCK
Data Out Setup Time (SOUT to SCK)
375
475
-
ns
(11)
tDXSCK
Data Out Hold Time (SOUT after SCK)
375
475
-
ns
(12)
tRISE
Output Rise Time (0.3VDD to 0.7VDD , CL = 100pF)
15
75
150
ns
(13)
tFALL
Output Fall Time (0.7VDD to 0.3VDD , CL = 100pF)
7
25
75
ns
(14)
tSTATH
Required STAT Pulse Width
-
20
75
ns
(15)
tRDYH
Required RDY Pulse Width
-
20
75
ns
tRESETL
Required RESET Pulse Width
-
20
75
ns
tSACTIVE
SACTIVE Delay from RDY (IDLE = VSS)
1150
1750
2450
ns
SACTIVE Delay from STAT (FTU = 0)
5
285
900
ns
(16)
(17)
tRDYSCK
Required RDY Removal Time Prior to Last SCK for Short RDY
-
25
100
ns
(18)
tSCKRDY
Required RDY Hold Time after Last SCK for Long RDY
-
0
100
ns
(19)
tREC
Required SERIAL Recovery Time (Minimum Time after SACTIVE
Until Next RDY/STAT)
-
675
750
ns
20
80
200
KHz
fSLOW
Slow clock detect frequency limit
NOTE:
1. All parameters are specifications of the HIP7010 component not of a system. Parameters specified as “Required” (i.e., tSTATH) refer to
the requirements of the HIP7010. If a “Required” pulse width is specified as 75ns maximum, that implies that 75ns is the maximum width
that any HIP7010 device will require. Therefore, a system that provides a minimum pulse width of 75ns will satisfy this maximum
requirement.
4
HIP7010
STAT
(INPUT)
(14)
RDY (SHORT)
(INPUT)
(15)
RDY (LONG)
(INPUT)
(16)
(17)
(18)
(19)
SACTIVE
(OUTPUT)
(1)
(2)
(13)
(12)
(3)
SCK
(OUTPUT)
(4)
(5)
(9)
D7O
SOUT
(OUTPUT)
(8)
D7I
(6)
D0O
D6I
D0I
(11)
(10)
SIN
(INPUT)
D6O
(7)
FIGURE 1. SERIAL INTERFACE TIMING DIAGRAM
NOTES:
1. Measurement points are from VDD /2, except 12 and 13 which are measured between VIL and VIH.
2. All timings assume proper CLK frequency and Divide Select values to generate 1MHz SCK.
Functional Pin Description
CLK (Clock - Input)
This section provides a description of each of the 14 pins of
the HIP7010 as shown in Figure 2.
IDLE 1
VPWIN 2
14 RDY
13 STAT
VPWOUT 3
12 CLK
VDD 4
11 VSS
RESET 5
10 SIN
TEST 6
SACTIVE 7
The Clock input (CLK) provides the basic time base reference for all J1850 symbol detection and generation. Serial
Bus transfers between the HIP7010 and the Host microcontroller are also timed based on the Clock input. Proper VPW
symbol detection and generation requires a 2MHz clock
which is internally derived from the CLK input. Various CLK
input frequencies can be accommodated via the Divide
Select bits in the Status/Control Register (see Status/Control Register for details).
An internal Slow Clock Detect circuit monitors the CLK input
signal and generates a HIP7010 reset if the clock is inactive
for more than 1/fSLOW. This is a safety mechanism to prevent
blocking the J1850 and Serial busses in the event of a clock
failure. The Slow Clock Detect reset can also be intentionally
invoked by externally inhibiting CLK input transitions.
Power can be reduced under Host control via the PowerDown
bit in the Status/Control Register (see Status/Control Register for details). Setting the Power-Down bit effectively stops
internal clocking of the HIP7010.
9 SOUT
8 SCK
FIGURE 2. 14 PIN DIP AND SO TERMINAL ASSIGNMENTS
VDD and VSS (Power)
Power is supplied to the HIP7010 using these two pins. VDD
is connected to the positive supply and VSS is connected to
the negative supply.
5
HIP7010
If IDLE is low when the host sets the NXT bit in the control
byte, the IDLE pin will pulse high for 2µs and then return low
(see Status/Control Register).
For enhanced noise immunity, the CLK input is a CMOS Schmitt
trigger input. See Electrical Specifications for input levels.
VPWOUT (Variable Pulse Width Out - Output),
VPWIN (Variable Pulse Width In - Input)
In general a Status/Control byte transfer should be performed
each time IDLE goes low. See Effects of Resets and PowerDown and Applications Information for more details.
These two lines are used to interface to a J1850 bus transceiver, such as the Intersil HIP7020. VPWOUT is the variable pulse width modulated output of the HIP7010’s symbol
encoder circuit. VPWIN is the inverted input to the symbol
decoder of the HIP7010. VPWIN is a Schmitt input.
The IDLE pin is an active low CMOS output. See Operation
of the HIP7010 for more details.
STAT (Request Status/Control - Input)
SIN (Serial In - Input),
SOUT (Serial Out - Output),
SCK (Serial Clock - Output),
SACTIVE (Serial Bus Active - Output)
The Request Status/Control (STAT) input pin is used by the
Host microcontroller to initiate an exchange of the Host’s control byte and the HIP7010’s status byte. A low to high transition on the STAT input signals the HIP7010 that the Host has
placed a control word in it’s SERIAL output register and is
ready to exchange it with the HIP7010’s status word. The
HIP7010 controls the exchange by generating the 8 SCKs
required. See Serial Interface (SERIAL) System and Applications Information for more details.
These four lines constitute the synchronous Serial Interface
(SERIAL) interface of the HIP7010. See the Serial Interface
(SERIAL) System for details. SIN, SOUT, and SCK provide
the three principal connections to the Host controller. SIN is a
CMOS input. SOUT and SCK are three-state outputs which
are only activated during serial transfers. The SIN, SOUT, and
SCK pins contain integrated pull-down load devices which
provide termination on the bus whenever it is in a high impedance state. The SACTIVE pin is a CMOS output, which pulls
low when the HIP7010 is communicating on the serial bus.
See Serial Interface (SERIAL) System and Applications
Information for more details.
The STAT pin contains an integrated pull-down load device
which will hold the pin low if it is left unconnected.
RESET (Reset - Input)
The RESET input is a low level active input, which resets the
HIP7010. Resetting the HIP7010 forces SACTIVE high, disables the SOUT and SCK pins, forces the VPWOUT output
low, drives IDLE high, and returns the internal state machine
to its initial state. Following reset, the HIP7010 is inhibited
from transmitting or receiving J1850 messages until a Status/Control Register transfer has been completed (see
Effects Of Resets And Power-Down for more details).
RDY (Byte Ready - Input)
The Byte Ready (RDY) line is a “handshaking” input from the
Host. Each rising edge on the RDY pin signifies that the Host
has loaded a byte into its SERIAL transmit register and the
HIP7010 can retrieve it (by generating clocks on SCK) when
the HIP7010 is ready for the data. See Serial Interface
(SERIAL) System and Applications Information for more
details.
The HIP7010 is also reset during initial power-on, by an
internal power-on-reset (POR) circuit.
Loss of a clock on the CLK input will cause a reset as
described previously under CLK.
The RDY pin contains an integrated pull-down load device
which will hold the pin low if it is left unconnected.
If not used, the RESET pin should be tied to VDD .
IDLE (Idle/Service Request - Output)
For enhanced noise immunity, the RESET input is a CMOS
Schmitt trigger input. See Electrical Specifications for
input levels.
The IDLE output pin indicates that the J1850 Bus has been
in a passive state for at least 275µs and is now idle. If the
bus has been passive for a minimum of 239µs and another
node initiates a new message, IDLE will pulse low for 1µs.
TEST (Test Mode - Input)
The TEST input provides a convenient method to test the
HIP7010 at the component level. Raising the TEST pin to a
high level causes the HIP7010 to enter a special TEST mode.
In the TEST mode, a special portion of the state machine is
activated which provides access to the Built-in-Test and diagnostic capabilities of the HIP7010 (see Test Mode for more
details).
In its role as a Service Request pin, a reset forces IDLE
high. Following the reset, IDLE remains high for 17 CLK
cycles and is then driven low. IDLE will remain low until 40
CLK cycles +1.5µs after completion of the first Status/Control byte transfer. The IDLE pin will then resume its normal
role, remaining high until a 275µs lull (or 239µs plus a passive to active transition) has been detected on the J1850
bus. This provides a handshake mechanism to ensure the
Host will reinitialize the HIP7010 each time the HIP7010 is
reset via POR, RESET, or Slow Clock Detect.
The TEST pin contains an integrated pull-down load device
which will hold the pin low if it is left unconnected. In many
applications the TEST pin will be left unconnected, to allow
access via a board level ATE tester.
If IDLE is low when an echo failure causes the ERR bit to be
set in the Status byte, the IDLE pin will pulse high for 2µs
and then return low (see Status/Control Register).
6
HIP7010
J1850 VPW Messaging
Anatomy of a J1850 VPW Message
All messages in a J1850 VPW system are sent along a single
wire, shared bus. At any given moment the bus can be in
either of two states: active (high) or passive (low). Multiple
nodes are connected to the bus as a “wired-OR” network in
which the bus is high if any one (or more) node is generating
an active output. The bus is only low when no nodes are generating active outputs. It follows that, when no communications are taking place the bus will rest in the passive state. A
message begins when the bus is first driven to the high state.
Each succeeding state transition (i.e., a change from active to
passive or passive to active) transfers one bit of information
(symbol) until the message is complete and the bus once
again rests at the passive state. The interpretation of each
symbol in the message is dependent on its duration (and
state), hence, the descriptor Variable Pulse Width (VPW).
This section provides an introduction to J1850 multiplexed
communications. It is assumed that the user is or will
become familiar with the appropriate documents published
by the Society of Automotive Engineering (SAE). The following discussion is not comprehensive.
Overview
The SAE J1850 Standard (Note 1) (J1850) establishes the
requirements for communications on a Class B multiplexed
wiring network for automotive applications. The J1850 document details the requirements in a three layer description
which separately specifies the characteristics of the physical
layer, the data link layer, and the application layer. There are
several options within each layer which allows vehicle manufacturers to customize the network while still maintaining a
level of universality.
Each message has a beginning and an end, the span of
which encompasses the entire message or frame (refer to
Figure 3). A frame consists of an active start of frame (SOF)
symbol and a passive end of frame (EOF) symbol sandwiched
around a series of byte sized (8-bit) groups of symbols. The
first byte of the frame contents is always a header byte, followed by possibly additional header bytes, followed by one or
more data bytes, followed by an integrity check byte (CRC
byte), followed by a passive end of data (EOD) symbol, followed by possibly one or more in-frame-response (IFR) bytes.
To keep waiting times low, messages are limited to 12 bytes
total (including header, data, check, and IFR bytes). All message bytes are transmitted most significant bit (MSB) first.
NOTE:
1. SAE J1850 Standard, Class B Data Communication Network
Interface, May 1994, Society of Automotive Engineers Inc.
The hardware of the Intersil HIP7010 provides features
which facilitate implementation of the 10.4Kbps Variable
Pulse Width Modulated (VPW) physical layer option of
J1850. In combination with a bus transceiver, such as the
Intersil J1850 Bus Transceiver HIP7020, and appropriate
software algorithms, the HIP7010 circuitry enables the
designer to completely implement a 10.4Kbps VPW Class B
Communications Network Interface per J1850. Features of
such an implementation include:
•
•
•
•
•
•
•
•
•
VPW Symbol Definitions
Single Wire 10.4Kbps Communications
Bit-by-Bit Bus Arbitration
Industry Standard Protocol
Message Acknowledgment (“In-Frame Response”) Capabilities
Exceptionally Tolerant of Clock Skew, System Noise, and
Ground Offsets
Meets CARB and EPA Diagnostic Requirements
Supports up to 32 Nodes
Low Error Rates
Excellent EMC Levels (when interfaced via Intersil J1850
Bus Transceiver HIP7020)
Within the J1850 scheme, symbols are defined in terms of both
duration and state (passive or active). The duration is measured as the time between successive transitions. There is one
transition per symbol and one symbol per transition. The end of
one symbol marks the beginning of the next. Since the bus is
passive when a message begins and must return to that same
state when the message completes, all frames have an even
number of transitions and hence an even number of symbols.
There are unique definitions for data bit symbols (all the symbols which occur within the header, data, and check bytes) and
protocol symbols (including SOF, EOD, and EOF). The duration
of each symbol is expressed in terms of VPW Timing Pulses
(TV values). Table 1 summarizes the TV definitions. Each TV is
specified in terms of a nominal (or ideal) duration and a minimum and maximum duration. The span between the minimum
and maximum limits accommodates system noise sources
such as node to node clock skew, ground offsets, clock jitter,
and electromechanical noise. There are no dead zones
between the maximum of one TV and the minimum of the next.
In addition to the standard J1850 features, the HIP7010 hardware provides a high speed mode, (intended for receive only
use) which can significantly enhance vehicle maintenance
capabilities. The high speed mode provides a 41.6Kbps communications path to any node built with the HIP7010.
SOF
HEADER
DATA 1
DATA 2
CRC
EOD
EOF
FIGURE 3. TYPICAL J1850 VPW MESSAGE FRAME
7
HIP7010
The terms short and long are often used to refer to pulses of
duration TV1 and TV2 respectively.
Table 2 summarizes the complete set of symbol definitions
based on duration and state.
TABLE 1. J1850 TV DEFINITIONS
TABLE 2. J1850 SYMBOL DEFINITIONS
DURATION (ALL TIMES IN µs)
TV ID
MINIMUM
NOMINAL
Illegal
0
TV1
>34
TV2
TV3
TV4
TV5
TV6
SYMBOL
0 Data
NA
≤34
1 Data
Active TV1 or Passive TV2
64
≤96
SOF (Start of Frame)
Active TV3
>96
128
≤163
EOD (End of Data)
Passive TV3
>163
200
≤239
EOF (End of Frame)
Passive TV4
>239
280
NA
IFS (Inter-Frame Separation)
Passive TV6
>239
300
NA
IDLE (Idle Bus)
Passive >TV6 Nominal
>280
300
NA
NB (Normalization Bit)
ActiveTV1 or Active TV2
BRK (Break)
Active TV5
VPW is a non-return-to-zero (NRZ) protocol in which each
transition represents a complete bit of information. Accordingly, a 0 data bit will sometimes be transmitted as a passive
pulse and sometimes as an active pulse. Similarly, a 1 data
bit will sometimes be transmitted as a passive pulse and
sometimes as an active pulse. In order to accommodate
arbitration (see Bus Arbitration) a long active pulse represents a 0 data bit and a short active pulse represents a 1
data bit. Complementing this fact, a short passive pulse represents a 0 and a long passive pulse represents a 1. Starting
from a transition to the active state, a 0 data bit will maintain
the active level longer than a 1. Similarly, starting from a
transition to the passive state, a 0 data bit will return to the
active level quicker than a 1. These facts give rise to the
dominance of 0’s over 1’s on the J1850 bus as depicted in
Figure 4. See Bus Arbitration for additional details.
DATA
BIT
1
DATA
BIT
J1850
BUS
The distinction between two of the passive symbols, EOD and
EOF, is subtle but important (refer to Figure 5). The EOD (TV3)
interval signifies that the originator of the message is done
broadcasting and any nodes which have been requested to
respond (i.e., to acknowledge receipt of the message) can now
do so. The EOD interval begins when the transmitting node has
completed sending the eighth bit of the check byte. The transmitter simply releases the bus and allows it to revert to a passive state. In the course of normal messaging, no node can
seize the bus until an EOD time has been detected. Once an
EOD has elapsed, any nodes which are scheduled to produce
an IFR will arbitrate for control of the bus (see Bus Arbitration)
and respond appropriately. If no responses are forthcoming the
bus remains in the passive state until an EOF (TV4) interval
has elapsed. After the EOF has been generated, the frame is
considered closed and the next communications on the bus will
represent a totally new message.
0
IFRs can consist of multiple bytes from a single respondent,
one byte from a single respondent, or one byte from multiple
respondents. In all cases the first response byte must be preceded by a normalization bit (NB) which serves as a start of
response symbol and places the bus in an active state so that
following the IFR byte(s) the bus will be left in the passive state.
1
LONGER ACTIVE
PULSE (0)
CONTROLS THE BUS
0
Passive TV1 or Active TV2
In Frame Response (IFR)
SYNCHRONIZED
0
DEFINITION
MAXIMUM
The NB symbol is by definition active, but can be either TV1
or TV2 in duration. The long variety (TV2) signifies the IFR
contains a CRC byte. The short variety (TV1) precedes an
IFR without CRC.
FIGURE 4A. DOMINANCE OF ACTIVE 0 DATA BIT
SYNCHRONIZED
Message Types
0
DATA
BIT
Messages are classified into one of four Types according to
whether the message has an IFR and what kind of IFR it is.
The definitions are:
0
1
DATA
BIT
• Type 0 - No IFR
1
J1850
BUS
0
• Type 1 - One byte IFR from a single respondent
(no CRC byte)
SHORTER PASSIVE
PULSE (0)
CONTROLS THE BUS
• Type 2 - One byte IFRs from multiple respondents
(no CRC byte)
FIGURE 4B. DOMINANCE OF PASSIVE 0 DATA BIT
FIGURE 4.
• Type 3 - Multiple byte IFR from a single respondent
(CRC appended)
8
HIP7010
The definition of 1 and 0 data bits (see Table 2 and discussion
under VPW Symbol Definitions) leads to 0’s having priority
over 1’s in this arbitration scheme. Header bytes are generally
assigned such that arbitration is completed before the first
data byte is transmitted. Because of the dominance of 0 bits
and the MSB first bit order, a header with the hexadecimal
value $00 will have highest priority, then $01, $02, $03, etc.
An example of two nodes arbitrating for control of the bus is
shown in Figure 6.
Bus Arbitration
The nature of multiplexed communications leads to contention
issues when two or more nodes attempt to transmit on the bus
simultaneously. Within J1850 VPW systems, messages are
assigned varying levels of priority which allows implementation of an arbitration scheme to resolve potential contentions.
The specified arbitration is performed on a symbol by symbol
basis throughout the duration of every message.
Arbitration begins with the rising edge of the SOF pulse. No
node should attempt to issue an SOF until an Idle bus has
been detected (i.e., an Inter-Frame Separation (IFS) symbol
with a period of TV6 has been received). If multiple nodes are
ready to access the bus and are all waiting for an IFS to
elapse, invariable skews in timing components will cause one
arbitrary node to detect the Idle condition before all others and
start transmission first. For this reason, all nodes waiting for
an IFS will consider an IFS to have occurred if either:
Arbitration also takes place during the IFR portion of a message, if more than one node is attempting to generate a
response. Arbitration begins with the NB symbol, which follows the EOD and precedes the first IFR byte.
For Type 1 and Type 3 messages only, the respondent which
successfully arbitrates for control of the bus produces an IFR.
All other respondents abort their IFRs.
For Type 2 messages, all respondents which lose arbitration
must re-attempt transmission at the end of each byte. Each
node, which successfully responds, eliminates itself from the
subsequent arbitration until all nodes have responded. This
arbitration scheme limits each respondent to a single byte during a Type 2 IFR.
1. An IFS nominal period has elapsed
or
2. An EOF minimum period has elapsed and a rising edge
has been detected
Arbitrating devices will all be synchronized during the SOF.
Beginning with the first data bit and continuing to the EOF,
every transmitting device is responsible for verifying that the
symbol it sent was the symbol which appeared on the bus.
Each transition, every transmitting node must decode the
symbol, verify the received symbol matches the one sent, and
begin timing of the next symbol. Since timing of the next symbol begins with the last transition detected on the bus, all
transmitters are re-synchronized each symbol. When the
received symbol doesn’t match the symbol sent, a conflict (bit
collision) occurs. Any device detecting a collision will assume
it has lost arbitration and immediately relinquish the bus. Typically, after losing arbitration, a device will attempt retransmission of the message when the bus once again becomes idle.
SOF
HEADER . . . . DATA N
Break
To force a message to be aborted before EOF is reached, a
break (BRK) symbol can be transmitted by any node. The
BRK symbol is an active pulse of duration TV5. Reception of a
break causes all nodes to reset to a ready-to-receive state
and to re-arbitrate for control following an IFS.
HIP7010 Architectural Overview
The HIP7010 consists of three major functional blocks: the
Serial Interface System (SERIAL) block; the State Machine
(STATE) block; and the Symbol Encoder/Decoder (SENDEC)
block. Transfers between the Host and the HIP7010 are controlled by the SERIAL block, while transfers between the
J1850 bus and the HIP7010 are handled by the SENDEC
CRC
EOD
IN FRAME RESPONSE
NB
EOD
EOF
FIGURE 5. J1850 MESSAGE WITH IN-FRAME-RESPONSE
TRANSMITTER
A
TRANSMITTER
B
J1850
BUS
IFS
SOF
0
0
0
0
0
0
0 1
0
1
0
COLLISION DETECTED BY B
HEADER
DATA 1 . . . DATA N
FIGURE 6. TWO NODES ARBITRATING FOR CONTROL OF J1850 BUS
9
CRC
EOF
HIP7010
Most Host micros which include a synchronous serial interface, operate their interface in a manner compatible with the
HIP7010s implementation. The result of each 8-bit SERIAL
transfer is that the contents of the HIP7010s shift register
and the Host’s shift register have effectively been “swapped”.
block. The STATE block controls the flow of all data between
the SERIAL and SENDEC blocks. The STATE block also controls Host/HIP7010 handshaking, automatic J1850 bus arbitration, break recognition, CRC checking, and many other
features. In addition to the three major blocks the HIP7010
includes CRC generator/checker hardware, a Status/Control
Register, and a Timing generator.
SERIAL Bus Timing
The SCK output of the HIP7010 is used to synchronize the
movement of data both into and out of the device on its SIN
and SOUT lines. As stated above, the Host and the HIP7010
are capable of exchanging a byte of information during a
sequence of eight clocks generated on the SCK pin. The
relationship between the clock signal on SCK and the data
on SIN and SOUT is shown in Figure 7.
Timing Generator
The timing generator, as its name suggests, generates all
internal timing pulses required for the SERIAL, SENDEC,
STATE, and CRC circuits. The CLK input pin is appropriately
divided to produce an internal 2MHz clock which results in a
1MHz SERIAL transfer rate and VPW J1850 symbol timing
with 1µs accuracy. The CLK pin of the HIP7010 can be driven
with a variety of common microcontroller frequencies. Frequency selection is accomplished via three bits in the Status/Control register. See Status/Control Register for more
details.
At least tLEAD prior to each series of eight clocks, the SACTIVE output of the HIP7010 is driven low. SACTIVE remains
low until a minimum of tLAG after the last clock transition.
When interfacing to a CDP68HC05 SPI compatible Host, the
SACTIVE output would normally be connected to the SS input
of the Host. The trailing edge of the SACTIVE signal can also
be used as a flag to Hosts which don’t automatically recognize
the transfer of a serial byte.
The Serial Interface (SERIAL) System
Overview
The quiescent state of SCK is low. Once a transfer is initiated, the rising edge of each SCK pulse places the next bit
on the SOUT line and the falling edge is used to latch the bit
input on SIN.
The SERIAL system handles all interface between the Host
microcontroller and the HIP7010. The SERIAL system is
designed to interface directly with the Serial Peripheral Interface (SPI) systems of the Intersil CDP68HC05 family of microcontrollers. Identical interfaces are found on the 68HC11 and
HC16 families. Compatible systems are found on most popular microcontrollers.
The Host must adhere to this same timing, by meeting the input
setup time requirements of SIN valid before the trailing edge of
SCK (see Electrical Specification for details) and latching
the SOUT data on the same edge. When interfacing the
HIP7010 to a CDP68HC05 SPI compatible Host, the SPI interface should be programmed with CPHA = 1 and CPOL = 0.
Serial data words are simultaneously transmitted and
received over the SOUT/SIN lines, synchronized to the SCK
clock stream. The word size is fixed at 8-bits. A series of
eight clocks is required to transfer one word. With the exception of Status/Control Register transfers (described later), all
SERIAL transfers use a single eight bit shift register within
the HIP7010. The serial bits are “shifted out” on the SOUT
pin, most significant bit (MSB) first, from the shift register. As
each bit shifts out one end of the shift register, the data on
the SIN input pin is, usually, shifted into the other end of the
same shift register. After eight clocks, the original contents of
the shift register have been entirely transmitted on the SOUT
pin and replaced by the byte received on the SIN pin.
At all times, other than during an actual SERIAL transfer
between the HIP7010 and its Host, the SCK and SOUT pins
are held in a high impedance state. This allows other devices
connected to the Host via the SERIAL bus to be accessed
when the HIP7010 is not transferring data. Utilization of the
SERIAL bus by the HIP7010 is less than 5%, leaving significant bandwidth for other transfers. When held in the high
impedance state, a pair of integrated pull-down devices on the
SCK and SOUT pull the pins to ground, if they are not driven
by another source. See Applications Information for a
detailed discussion of SERIAL bus utilization.
SACTIVE
SCK
SCK NORMALLY LOW
MSB
6
5
4
3
2
1
LSB
INTERNAL STROBE FOR LATCHING DATA IN HIP7010
SOUT
MSB
6
5
4
3
2
1
LSB
SIN
MSB
6
5
4
3
2
1
LSB
FIGURE 7. SERIAL BUS TIMING
10
HIP7010
such it is always the last byte. For sake of consistency the
HIP7010 requires a long RDY for Type 1 and Type 2 IFRs.
See Status/Control Register and Application Information
for more details.
SERIAL Bus Transfers
The HIP7010 is always configured as a SERIAL “master”. As
a master, the HIP7010 generates the transfer-synchronizing
clock on the SCK pin, transmits data on the SOUT pin, and
receives data on the SIN pin.
The other handshaking input is the Request Status/Control
(STAT) input pin. STAT is used by the Host microcontroller to
initiate an exchange of the Host’s control byte and the
HIP7010’s status byte. A low to high transition on the STAT
input signals the HIP7010 that the Host has placed a control
word in it’s serial output register and is ready to exchange it
with the HIP7010’s status word. The HIP7010 will generate
the eight SCKs for the solicited transfer as soon as feasible.
To avoid confusion with the transfer of a received J1850
byte, STAT should generally be pulsed shortly after receiving
each data byte from the HIP7010. This technique is safe,
because once a J1850 message byte has been received
from or sent to the HIP7010, another unsolicited transfer is
guaranteed not to happen for at least 500µs. A Control/Status byte transfer should also be performed in response to
each high to low transition on the IDLE line. See Application Information for more details.
Whenever the HIP7010 receives a complete byte from the
J1850 bus via the VPWIN line, it automatically initiates an
unsolicited SERIAL transfer. The unsolicited transfer transmits the received (or reflected) byte to the Host and, if in the
midst of transmitting a message, retrieves the next byte from
the Host. While these unsolicited transfers are, strictly
speaking, asynchronous to the Host’s activities, there are
well defined rules which govern the minimum time between
unsolicited transfers (i.e., no two unsolicited transfers can
occur in less time than it takes to transfer one J1850 byte (8
x 64 = 512µs). See Applications Information for more
details.
In addition to the unsolicited transfers which are based on
receipt of incoming J1850 messages, the Host can initiate
certain transfers in a more synchronous fashion. Handshaking between the Host and the HIP7010 is provided by the
Byte Ready (RDY) and Request Status (STAT) pins. These
two pins are driven by the Host and trigger the HIP7010 to
initiate one of the two, unique, solicited SERIAL transfers.
Status/Control Register
The Status/Control Register is actually a pair of registers:
the Status Register and the Control Register. When the Host
initiates a Status/Control Register transfer by raising the
STAT input, the HIP7010 sends the contents of the Status
Register to the Host and simultaneously loads the Control
register with the byte received from the Host.
The Byte Ready (RDY) line is the first of two handshaking
inputs from the Host. Each rising edge on the RDY pin signifies that the Host has loaded a byte into its serial transmit
register and the HIP7010 can retrieve it. If the J1850 bus is
available (i.e., IFS has elapsed) the rising edge of RDY is
interpreted as signalling the first byte of a new message. The
HIP7010 immediately performs a solicited SERIAL transfer
to load the first byte. Prior to performing the transfer, the
HIP7010 drives the J1850 bus high to initiate an SOF symbol. The SOF is then followed by the eight symbols which
represent the transferred byte. If a J1850 message is
already in progress, the rising edge of RDY is interpreted as
signalling that the next byte of the message or of an IFR is
ready to be transferred from the Host. The HIP7010 will initiate the transfer, as an unsolicited transfer, when conditions
on the J1850 bus warrant the transfer (i.e., when the previously retrieved byte has been completely transmitted on the
J1850 bus or after EOD for an IFR).
Status Register
The Status Register contains eight, read-only, status bits.
7
6
5
4
3
2
1
0
EOD
MACK
0
FTU
4X
CRC
ERR
BRK
B7, EOD When an EOD symbol has been received on
VPWIN and an IFR byte is received from the
J1850 bus, the End-of-Data flag (EOD) is set, during the unsolicited transfer of the byte from the
HIP7010 to the Host. EOD remains set, until the
unsolicited transfer of the first byte of the next
frame.
While the rising edge of RDY is used to notify the HIP7010
that the Host is ready to supply the next byte, the level of
RDY following the actual serial transfer provides additional
information. Figure 1 depicts the use of RDY. By driving the
RDY line high and returning it low before the transfer has
been completed, the HIP7010 will detect a low. This is
referred to as a short RDY. If the RDY line is brought high
and held high until the transfer is complete, a high level is
detected by the HIP7010. This is referred to as a long RDY.
EOD can be used to distinguish the IFR portion of
a frame from the message portion.
EOD is cleared by reset.
B6, MACK If MACK (Multi-byte ACKnowledge) is high, either
the MACK control bit has been set during a previous Status/Control Register transfer or a long normalization bit has been received following an EOD.
When both MACK is set and the EOD flag (see B7,
EOD) is set, the most recent data byte transferred
is part of a Type 3 IFR.
A short RDY signals a normal transfer, but a long RDY has
special significance. A long RDY indicates that the byte currently sitting within the Host is the last byte of a message or of
an IFR. When transmitting the body of a message or a Type 3
IFR the HIP7010 will automatically append the CRC after the
byte for which the long RDY was used. When responding with
a Type 1 or Type 2 IFR the response is a single byte, and as
The value of MACK is only relevant if EOD = 1.
MACK remains set until the unsolicited transfer of
the first byte of the next frame.
MACK is cleared by reset.
11
HIP7010
B5, 0
Bit 5 of the Status byte is not used and will always
read as a 0.
B4, FTU
When First Time Up (FTU) is high, it indicates
that a reset has occurred since the last Status/Control Register transfer. FTU is high during
the first Status/Control Register transfer after a
reset and low thereafter.
Control Register
The Control Register contains eight, write-only, control bits.
The PD, NXT, MACK, and ACK bits can only be set high;
they are cleared by hardware under specific conditions. The
other four bits can be both set and reset by the Host. All bits
in the Control Register are cleared by reset.
FTU can be used to recognize that a Slow Clock
Detect reset has occurred or to ensure that a Status/Control Register transfer has been successfully completed since the last reset.
B3, 4X
7
6
5
4
3
2
1
0
ACK
MACK
NXT
PD
4X
DS2
DS1
DS0
B7, ACK Setting the Acknowledgment (ACK) bit signals the
HIP7010 that, following the EOD, an IFR
response is to be sent. Once set, the ACK bit cannot be cleared by the Host. ACK is cleared upon
successful transmission of the IFR or at the next
Idle.
The 4X status flag indicates that the 4X mode bit
has been set in the Control Register. This bit
reflects the contents of the Control Register not
the current mode of the HIP7010’s SENDEC. The
SENDEC only changes modes synchronously
with an edge detected on the VPWIN pin. See
description of the 4X control bit for details. 4X is
cleared by reset and the trailing edge of a break.
The ACK bit can be set anytime prior to 135µs
after the final byte (the CRC) of a message. The
first IFR byte must be loaded into the Host’s serial
output register, and the RDY line set after the
HIP7010 transfers the next-to-last byte to the
Host, and before the HIP7010 transfers the last
byte (CRC) of the J1850 message to the Host.
When the CRC byte is sent to the Host from the
HIP7010, the IFR byte will be simultaneously
loaded into the HIP7010.
B2, CRC The CRC Error flag (CRC) is set when a CRC
error has been detected in the current frame.
CRC is cleared by reset and at the conclusion of
the Status/Control Register transfer.
B1, ERR The Error flag (ERR) is set when an illegal symbol
or other, non-CRC error has been detected on the
VPWIN pin. Following are some of the many errors
which will cause ERR to be set: 1. An illegal symbol, (i.e., a symbol other than a TV1, TV2, or Break
in the middle of a data byte); 2. Receipt of a truncated byte (i.e., less than 8 symbols); 3. The Host
attempting to initiate a message more than 96µs
after the IDLE line goes high; 4. An improperly
framed message (i.e., SOF not equal to TV3,
wrong EOD, EOF, or NB widths); 5. Failure by the
Host to use the long form of RDY to indicate the
last byte of a message; 6. An attempt by the Host
to transmit a single byte (Type 1 or Type 2) IFR by
setting ACK but without using the long form of RDY
for the byte transfer; 7. Setting the Host asserting
STAT during a data byte transfer; 8. A transition
has occurred on the VPWOUT pin and the
reflected transition has not been detected on
VPWIN (echo fail).
To send a single byte (Type 1 or Type 2) IFR the
Host must leave MACK (B6 of the Control Register) low and use the long RDY line format.
When sending a single byte (Type 1 or Type 2)
IFR, the possibility of losing arbitration exists. In
the case of a Type 1 IFR no further action should
be taken. The standard protocol for handling loss
of arbitration during a Type 2 IFR is to re-attempt
the transmission until successful. To ensure
proper transmission of the IFR the Host must
repeatedly load it’s serial output register with the
desired IFR byte, and set RDY (using the short
format), until the IFR has been properly received
back. There is no danger of inadvertently sending
the IFR byte twice. The HIP7010 monitors the
arbitration results and will transmit the IFR byte
only once. The ACK bit is automatically cleared
upon the first successful transmission, thus preventing a second transmission. The Host controls
when the ACK bit is set. During normal operation
the Host must only set ACK once per IFR.
ERR is cleared by a reset and at the conclusion
of the Status/Control Register transfer.
To send a Type 3 IFR the Host must set MACK
high and use the short format of the RDY for all
bytes except the last, when the long format is
used. A CRC will automatically be appended to
the last byte of a Type 3 IFR. A Type 3 IFR, consisting of a single byte plus CRC, can be created
by setting MACK high and using the long RDY line
format for loading the single data byte.
B0, BRK The break flag (BRK) is set on the first rising edge
of VPWIN after a BRK symbol has been detected
on the J1850 bus. If the Host was transmitting or
has a message to transmit, it should re-arbitrate
for the bus following an IFS (IDLE goes low).
BRK automatically clears the 4X mode of the SENDEC and resets the 4X bit in the Status byte.
BRK is cleared by a reset or at the conclusion of
the Status/Control Register transfer.
When sending a Type 3 IFR, the possibility of losing arbitration during the IFR also exists. In the
case of Type 3 IFRs, once arbitration has been
12
HIP7010
PD can only be set if the IDLE pin is low or during
the first Status/Control Register transfer following
a reset. The CLK input is internally gated off at
the end of the Status/Control Register transfer.
lost the Host no longer needs to continue transmitting bytes. As in the case of Type 2 IFRs, the Host
cannot know arbitration has been lost until after the
next byte to transmit has been loaded. Again, there
is no danger of sending extra bytes because the
HIP7010 automatically suspends transmissions
once arbitration is lost.
There are two situations which can cause the PD
bit to be cleared prematurely: 1. The RDY input is
high during the Status/Control Register transfer
(since this is under control of the Host it should be
avoided); 2. A noise pulse of less than 7µs duration occurs on the VPWIN line.
B6, MACK The Multi-byte Acknowledge (MACK) bit, in conjunction with the ACK bit, signals the HIP7010 that,
following the EOD, a Type 3 IFR with CRC
response is to be sent. Once set, the MACK bit
cannot be cleared by the Host. MACK is cleared
upon detection of an Idle following the transmission of the IFR. Setting MACK without also setting
ACK will result in no IFR being transmitted.
If either of these situations occur, the PD will be
cleared, the HIP7010 will resume operating and
look for a valid edge on VPWIN, RDY, or STAT. If
no valid edge has occurred the HIP7010 will recycle to the top of the State Machine, pulsing IDLE
high for a minimum of 2µs. It is the responsibility
of the Host to monitor the IDLE pin after setting
PD to ensure that the POWER-DOWN mode has
been successfully entered.
The MACK bit can be set anytime prior to 135µs
after the final byte (the CRC) of a message. The
first IFR byte must be loaded into the Host’s serial
output register, and the RDY line set after the
HIP7010 transfers the next-to-last byte to the Host,
and before the HIP7010 transfers the last byte
(CRC) of the J1850 message to the Host. When
the CRC byte is sent to the Host from the
HIP7010, the first IFR byte will be simultaneously
loaded into the HIP7010. To send a Type 3 IFR the
Host uses the short format of the RDY for all bytes
except the last, when the long format is used.
See Effects of Resets and Power-Down for a
detailed discussion of the Power-Down mode.
B3, 4X
Setting the MACK bit in the Control Register is not
immediately reflected in the MACK bit of the Status
Register. The status bit is updated following each
data transfer.
B5, NXT
The 4X bit can only be written to when the IDLE
pin is low or during the first Status/Control transfer
following a reset. Setting 4X is inhibited during the
first Status/Control after a Break. The SENDEC
begins operating at the 4X rate upon receipt of the
next edge. The system must provide sufficient time
for all nodes to detect the Idle, interpret the “shift to
high speed” message, and change their mode bits
before issuing a high speed SOF.
If the Wait for Next Idle (NXT) bit is asserted high
during a Status/Control Register transfer, the
HIP7010 State Machine is re-initialized to a “wait
for Idle” state. The VPWOUT pin is driven low and
the IDLE pin is reset high. Activity on the VPWIN
pin is ignored until a valid Idle is detected. When
NXT is asserted the IDLE pin will go high for a minimum of 6µs. If the bus is Idle at the end of the 6µs
period, IDLE will be driven low and the HIP7010
will be ready to transmit or receive a J1850 message. If the bus is not Idle, current activity on the
VPWIN pin is ignored until a new Idle is detected.
4X is cleared by receipt of a Break symbol on the
J1850 bus and it can also be cleared by performing a Status/Control Register transfer with the 4X
bit low. When cleared via a Status/Control Register transfer, IDLE must be low. The SENDEC
reverts to operating at the normal rate upon
receipt of the next edge.
The NXT bit enables the Host to ignore the balance of the current message. Unsolicited transfers
from the HIP7010 are guaranteed not to occur until
the next Idle occurs. Transfers resume following
the first byte of the next message.
B4, PD
Setting the High Speed Mode (4X) bit causes the
HIP7010’s SENDEC to decode symbols received
on the J1850 bus at 0.25X the normal durations.
The 4X mode is designed to allowed receipt of messages at 4X the normal J1850 rate. It is intended for
manufacturing and diagnostic use, not normal
“down the road” vehicle communications. Transmission is inhibited while the 4X bit is set.
4X mode cannot be utilized for transmitting messages. VPWOUT is disabled in hardware, but the
State Machine will attempt to transmit if RDY is
strobed. It is the Host’s responsibility to refrain
from transmitting in 4X mode.
The Power-Down (PD) bit is used to halt internal
clocks to the HIP7010 to minimize power. A low
level on the VPWIN, a low to high edge on the
STAT pin, or a high level on the RDY pin will clear
the PD bit and normal HIP7010 functions will
resume.
B2, DS2, B1, DSI, B0, DSI
The three Divide Select bits (DS2-DS0) are used
to match the internal clock divider with the input
frequency on the CLK input to produce the
required 2MHz internal time base. Table 3 shows
the clock divide values and nominal input frequency for the eight combinations of DS2-DS0.
13
HIP7010
pin and input, as a digital signal, on the VPWIN pin. These
two lines must be connected through a bus transceiver (such
as the Intersil J1850 Bus Transceiver HIP7020) to the single
wire J1850 bus. The transceiver is responsible for generating
and receiving waveforms consistent with the physical layer
specifications of J1850. In addition, the transceiver is responsible for providing isolation from bus transients.
During a HIP7010 reset caused by a POR, a Slow
Clock Detect, or a low on the RESET line, the
Clock Divider is inhibited and a fixed divide-by sixteen clock divider is activated. This is greater than
any selectable divide-by and guarantees proper
operation of the SERIAL interface for all valid operating frequencies (although the transfer rate will be
below 1MHz). The CLK divide-by remains at sixteen and operation of the HIP7010 is suspended
until the Host performs a Status/Control Register
transfer to set the proper divide value. The State
Machine and SENDEC are held in a reset state
(passive) until the first Status/Control Register
transfer has been completed. This ensures proper
setting of the divide selects prior to generation or
receipt of any symbols.
Every symbol sent out on the VPWOUT is, in effect, inverted
and reflected back on the VPWIN pin after some finite delay
through the transceiver. In actuality, only active symbols are
guaranteed to be reflected unchanged. If the transmitted
symbol is passive and another node is simultaneously sending an active symbol, the active symbol will dominate and
pull the bus to a high level. The SENDEC circuitry includes a
3-bit digital filter which effectively filters out noise pulses less
than 7µs in duration.
TABLE 3. DS2-DS0 CLOCK DIVIDER SELECTIONS
INTERNAL
HIP7010 CLK
DIVIDE-BY
DS2
DS1
DS0
CLK INPUT
FREQ. (MHZ)
0
0
0
24 (Note 1)
12
0
0
1
12
6
0
1
0
20 (Note 1)
10
0
1
1
10
5
1
0
0
16 (Note 1)
8
1
0
1
8
4
1
1
0
4
2
1
1
1
2
1
The STATE logic transfers data bits between the SERIAL
system and the SENDEC, and handles addition of required
frame elements such as the SOF symbol and the CRC byte.
When transmitting bytes, bits are taken from the SERIAL
shift register and translated into the required symbols, bit by
bit. Timing of each symbol is calculated from the last
transition on the VPWIN line which keeps all nodes on the
J1850 bus “in synch” during arbitration periods.
Decoding of received symbols is automatically performed by
the SENDEC. The decoded symbol is translated to a 0 or 1
value and transferred by the STATE logic into the SERIAL shift
register. As each symbol is decoded, it is shifted into the
SERIAL shift register and, if transmitting, the next bit to transmit
on the J1850 bus is shifted out. Once an entire byte has been
loaded into the SERIAL shift register the STATE logic automatically generates an unsolicited transfer of the byte to the Host.
NOTE:
Whenever the SENDEC is transmitting, it is simultaneously
monitoring the “reflected” symbol on the VPWIN line. At
each transition the reflected symbol is read and compared to
the sent one. If the reflected symbol doesn’t match the symbol sent, a collision has occurred and the HIP7010 automatically disables transmissions until the next Idle/IFR period. If
there was no collision, the HIP7010 continues transmitting
until the entire byte has been sent. Once the byte has been
sent, a full byte will also have been reflected and received by
the HIP7010. As discussed above, the HIP7010 initiates a
transfer of the received byte to the Host, which allows the
Host the opportunity to compare the sent and reflected
bytes, and to transfer the next byte of the message.
1. Invalid operating frequency.
Once DS2-DS0 have been set following a reset,
they must not be altered. Each Status/Control Register transfer must properly reassert the same
DS2-DS0 values to maintain proper clocking.
Selecting a DS2-DS0 combination which is too low
for the given CLK frequency can result in loss of
SERIAL communications, due to excessive clocking rates. In such instances the only recovery
mechanism is to force a HIP7010 reset by pulling
the RESET input low, interrupting the CLK input, or
performing a power-on reset. A well behaved Host
will avoid changes to DS2-DS0. System fault tolerance can be maximized by using the lowest possible
frequency at the CLK input.
In addition to features already discussed, the SENDEC
includes, noise detection, Idle bus detection, a wake-up facility, “no echo” detection, and a high speed receive mode. Symbol timing is based on the main CLK input. The programmable
prescaler, controlled by the DS0-DS2 bits in the Control Register, allows proper SENDEC operation with a variety of CLK
input frequencies (see DS2-DS0 under Status/Control Register for prescaler details). The high speed mode is a J1850
extension which allows production and/or maintenance equipment to transmit messages at 4X the normal 10.4Kbps rate
(see 4X under Status/Control Register for prescaler details).
Power-down does not reset DS2-DS0, allowing
rapid “wake-up” from the Power-down state.
Symbol Encoder/Decoder (SENDEC)
Operation
The Symbol Encoder/Decoder (SENDEC) hardware integrated in the HIP7010 handles generation and reception of
J1850 messages on a symbol by symbol basis. Symbols are
output from the SENDEC, as a digital signal, on the VPWOUT
Software algorithms can be implemented in the Host to provide message buffering and filtering and other needed fea-
14
HIP7010
tures to create a complete J1850 VPW node. See the
Applications Information section for typical algorithms.
Detection of a Break on the J1850 bus causes an interrupt
input to STATE which causes the HIP7010 to cease any current transmission and enter a wait for IDLE mode.
The State Machine Logic (STATE)
Effects of Resets and Power-Down
The State Machine Logic (STATE) of the HIP7010, is a
sequential state machine implementation of the J1850 VPW
data link layer. STATE controls data flows within the HIP7010
and between the Host and the J1850 bus.
Resets
A Power-On reset, a Slow Clock Detect reset, and a low on
the RESET pin all have an identical effect on the operation of
the HIP7010. All resets are asynchronous and immediately
do the following:
When receiving messages, STATE monitors the input from
the SENDEC, building byte sized chunks to send to the Host.
As each byte is assembled, STATE transfers the result to the
Host via the Serial interface, as an unsolicited transfer. Upon
receipt of a complete message (recognized by EOD), STATE
verifies both the CRC and bit counts and sets appropriate
Status Register flags.
• VPWOUT is forced low.
• The HIP7010 is set to RESTART mode.
• The internal divide-by is set to sixteen and held at that
value until the RESTART mode ends.
• SACTIVE is forced high and SCK and SOUT are set to a
high impedance state.
• The ACK, MACK, NXT, PD, and 4X bits are cleared in the
Control Register.
• All Status Register bits are cleared (except bit 4, FTU,
which is set to a 1).
• IDLE is forced high and held high for 17 CLKs after the
source of the reset is removed. After 17 CLKs, IDLE is
forced low. IDLE Remains low until 40 CLKs +1.5µs after
the first Status/Control Register transfer.
• The SENDEC is reset, holding the symbol timer at a count
of 0 and clearing the 3-bit VPWIN filter to all 0’s, until the
RESTART mode ends.
• STATE is held in a reset loop until the RESTART mode
ends. While STATE is in the reset loop, transitions on the
RDY pin are ignored.
When transmitting messages from the Host to the J1850
bus, STATE waits for the first RDY input transition, after
which it retrieves the first byte from the Host and initiates the
message with an SOF. Each bit of the Host’s message byte
is transferred to the J1850 bus via the SENDEC. When the
transfer of a byte is complete, STATE checks for a new RDY
(if there is one), retrieves the associated byte, and again
transfers the byte via the SENDEC to the J1850 bus. After
retrieving each byte from the Host, STATE checks to see if
the long RDY format was used, which indicates this is the
end of the Host’s message. If the message is complete,
STATE transfers the final byte to the J1850 Bus and then,
automatically, sends the computed CRC to the J1850 bus.
Throughout the transmission of a message from the Host to
the J1850 bus, STATE monitors the symbols reflected back
via the SENDEC and handles all bus conditions such as loss
of arbitration, illegal bits, Break, bad CRC, and missing bits.
STATE also catches Host errors including failure to set the
RDY line in time for the next byte transfer, attempting to initiate a new message more than 96µs after IDLE has gone
away, and inappropriate use of the STAT line (i.e., requesting
a Status/Control Register transfer during an unsolicited
transfer of the reflected data).
The RESTART mode is entered by any reset and ends when
the first Status/Control Register transfer has been completed. Upon exiting the RESTART mode the HIP7010
enters its normal RUN mode. This is reflected in the clearing
of the FTU bit of the Status Register.
When the RESTART mode ends and the RUN mode begins,
the internal divide-by is set to the value programmed via
DS2-DS0 in the Control Register. The IDLE pin is driven
high after 40 CLKs, the SENDECs counter and VPWIN filter
begin operating, and STATE begins monitoring the outputs
of SENDEC looking for an Idle.
In 4X mode VPWOUT is disabled in hardware, but STATE
will attempt to transmit if RDY is strobed. This results in
STATE clearing IDLE and waiting for the leading edge of
SOF. Since VPWOUT is blocked STATE will only recover if
another node’s SOF is received or NXT is set. It is the Host’s
responsibility to refrain from transmitting in 4X mode.
The HIP7010 remains in RUN mode until another reset
occurs or the POWER-DOWN mode is entered.
Power-Down
The Control Register bits influence STATE. If ACK is set,
STATE handles sequencing of the requested IFR. The flow
consists of waiting for an EOD, sending the appropriate Normalization Bit (Type 1/2 vs Type 3 IFR), transferring the IFR
byte(s) from the Host to the J1850 bus, handling arbitration,
and finally adding the CRC to Type 3 IFRs. As with normal
transmissions, STATE contains error handling to react appropriately to all J1850 bus conditions.
The POWER-DOWN mode of the HIP7010 is entered by setting the PD bit in the Control Register (see Control Register
for more information). Setting the PD bit can only be done
when the HIP7010 is driving the IDLE pin low. Once set, the
PD forces the HIP7010 to the POWER-DOWN mode 2µs
after the completion of the Status/Control Register transfer.
While in the POWER-DOWN mode the CLK input is internally
gated off, minimizing power dissipation. The Slow Clock
Detect is inhibited while in the POWER-DOWN mode.
Detection of an Idle on the bus causes STATE to set the IDLE
pin. STATE clears the IDLE pin upon receipt of a transition on
the VPWIN line or when the Host initiates a new message.
A return to the RUN mode from the POWER-DOWN mode is
normally caused by a low level on VPWIN. During POWER-
15
HIP7010
Test Block 1
DOWN the input signal is not filtered via the 7µs digital filter (no
clocks are available to drive the digital filter). Without filtering in
place it is possible for a noise spike, less than 7µs wide, to
wake-up the HIP7010. In such a case the HIP7010 returns to
RUN mode, but the spike is rejected by the now running, digital
filter and the bus continues in the Idle state. To notify the Host
when such spurious wake-ups occur, STATE monitors the output of the digital filter and if, within 12µs after the wake-up, the
digital filter doesn’t indicate VPWIN is low, STATE pulses IDLE
high for 2µs and then drives it low again. The HIP7010 is now in
the RUN mode. It is the responsibility of the Host to recognize
the pulse on the IDLE pin and set PD in the Control Register to
reenter the POWER-DOWN mode. In systems where the Host
directly monitors the VPWIN pin during POWER-DOWN, monitoring the IDLE pin may not be necessary.
Once the TEST Sequence has been entered, IDLE will go
low. Once IDLE has gone low, each time that RDY is pulsed
(with the short form of RDY) it will result in an exchange of
data between the Host’s SPI register and the BLIC’s data
register. Following a reset, the BLIC’s data register will contain $00. For all other exchanges during the TEST sequence
the BLIC will give back to the Host the byte it supplied during
the prior exchange. During each exchange the IDLE pin will
go high and return low when the exchange is complete. Following each exchange the Host should query the BLIC’s Status Register by pulsing STAT. All flags should be clear.
This section of the TEST Sequence not only checks proper
operation of the Serial Register of the BLIC, the TEST, IDLE,
RDY, and STAT pins but it also does an internal verification of
>70% of the inputs of the BLIC’s State Machine.
One of the mechanisms to exit POWER-DOWN is to provide a
high level on the RDY pin. Since this is a level sensitive event
the HOST must ensure that RDY is not already high when the
PD bit is set in the Control Register. A well behaved Host will
control this properly. However, in the event RDY is high when
PD is set, a 12µs time-out will occur similar to that described
for waking-up with a noise pulse on VPWIN. After the timeout, IDLE will pulse high for 2µs then low again. The Host
should react to this pulse appropriately.
Test Block 2
The TEST Sequence can now be exited by lowering TEST
and setting the NXT bit in the Control Register, or the second
portion of the TEST Sequence can be invoked by leaving
TEST high and doing one last transfer of an $FF using the
long form of RDY. Following this exchange the BLIC will send
a high TV2 followed by a low TV1 followed by a high noise
pulse (to prevent bus interference the HIP7020 Transceiver
should be in Loopback Mode during this sequence). Following
the noise pulse, the State Machine will return to the start of
the TEST Sequence and IDLE will go low. If all tests were successful the ERR bit should be set in the Status Register (due
to the noise pulse) and the Serial Data Register should have
been set to $00 (done following the TV1). This can be verified
by doing a STAT transfer followed by a RDY transfer. Normally
the TEST Sequence would now be exited by lowering TEST
and setting NXT in the Control Register.
Test Mode
Overview
When the TEST Pin of the HIP7010 is driven high, it modifies the operation of the BLIC in two ways:
1.
2.
It inhibits receipt of bus signals on the VPWIN pin and
internally routes the VPWOUT signal to the VPWIN
input. During this “loopback” mode of operation the
VPWOUT pin will continue to operate.
The State Machine which controls the operation of the
HIP7010 is extended to include a special TEST Sequence.
The TEST Sequence can only be entered from one location in the normal State Machine flow. This point can conveniently be reached following reset of the BLIC or by
setting the NXT bit in the BLIC’s Control Register.
The second block of the TEST Sequence boosts the number
of tested State Machine inputs to over 90%.
Using TEST for Loopback Operation
Whenever TEST is high the BLIC is operating in “loopback”
mode. This provides a convenient means to isolate faults
between the Bus, the Transceiver, and the BLIC. It also simplifies extended testing of the BLIC’s Symbol Generation/Detection,
Message
Handling
and
CRC
Generation/Detection logic.
Entering the TEST Sequence
Entry into the TEST Sequence of the BLIC’s State Machine
requires that the TEST pin is high and the State Machine is
at it’s “start”. The State Machine will always pass through its
starting point at certain identifiable times:
1.
2.
3.
4.
To isolate Module faults from Bus faults: place the HIP7020
Transceiver in loopback (by lowering LBE) and send a message. Verify the message and CRC are properly reflected
and the Status bits are clear. If all are good, the fault can be
assumed to be on the output of the Transceiver or on the bus
itself. If all are not good, leave the Transceiver in loopback
and place the BLIC in loopback (to place the BLIC in loopback, wait for IDLE to go low and then raise TEST) and send
a message again verifying that the message and CRC are
properly reflected and that the Status bits are clear. If all are
good the Transceiver or VPWOUT or VPWIN of the BLIC are
faulty. If all are not good the fault is either internal to the BLIC
or is a problem with the Host/BLIC interface. If the TEST
Sequence can be properly run the problem has been isolated to an internal fault of the HIP7010.
Following the first Status/Control Transfer after a Reset
Following completion of a J1850 message (i.e., after EOD)
Following abortion of a message frame due to noise, bad
symbol, bad CRC, receipt of a Break, etc.
Following setting of the NXT bit in the Control Register
As are all states, the starting point is a transitory state. Once
entered, the State Machine will remain at its start only until
the bus has been low for a TV4 min (i.e., EOF, 239µs). To
ensure proper synchronization, the TEST Sequence should
generally be entered only after a Reset or after setting the
NXT bit in the BLIC’s Control Register.
16
HIP7010
Error Handling
waiting for an Idle. That is to say that the current message
is discarded. “Waiting for Idle” happens following: Reset,
setting of NXT, any error which sets ERR (except asserting
STAT during a data transfer), a CRC error, a Break, or following EOD after a Type 1, 2, or 3 message.
The Status Register
The various flags in the Status Register can be used to
detect many errors which would typically be generated by
system noise, errant nodes, or improperly designed Host
code. It is good practice to maintain error counts in the Host
for service reporting and to trigger recovery procedures.
Whenever the ERR or CRC are set in the Status Register,
the current message is aborted and the BLIC enters a “wait
for Idle” mode. Following is a detailed listing of the errors
which can be trapped by reading the Status Register.
3.
Errors Which Set the ERR Flag
The ERR flag will be set whenever:
1.
A noise pulse (i.e., a symbol less than TV1MIN) is received
- including while waiting for an Idle.
2.
An illegal symbol, (i.e., a symbol other than a TV1, TV2, or
Break) is received in the middle of a message which is
being received or transmitted.
3.
After a Type 1, 2, or 3 message, a second NB or an SOF
for a new message received before EOF will be ignored.
Any following symbols will be ignored until EOF is
detected. This implies that if two messages appear on the
bus with less than an EOF between them the second message will be ignored, but no error generated. Similarly, if an
IFR is attached to a message after EOD and a second NB
is generated an EOD after the initial IFR, the NB and all
succeeding symbols will be ignored until Idle is detected.
No error will be generated.
Errors Which Set the CRC Flag
The CRC flag will be set whenever:
1.
The CRC check byte of the body of any type message is
bad (any IFR will be aborted/ignored).
A message with an incomplete byte is received (i.e., total
data bit count not equal to 0 modulo 8).
2.
All components of a Type 3 message frame are good
except the IFR’s CRC check byte.
4.
The Host attempts to initiate a message more than
TV2MIN (96µs) after the IDLE line goes high.
3.
A zero length message (SOF followed by EOD) is received.
5.
An improperly framed message is received (i.e., SOF not
equal to TV3, wrong EOD, EOF, or NB widths).
6.
An SOF occurs less than TV4 after the end of a Type 0
message.
7.
While transmitting a message that the Host fails to assert
RDY prior to a data transfer.
8.
The Host fails to use the long form of RDY to indicate the
last byte of a message.
9.
The Host attempts to transmit an IFR by setting ACK but
fails to assert RDY prior to 135µs after the CRC.
Host Time-outs
Other classes of errors, including catastrophic failure of the
J1850 bus, can sometimes only be detected by monitoring
the time between successfully received messages and/or
the delay between IDLEs - when the time exceeds some limit
the Host assumes that a bus fault exists and attempt to isolate the cause (perhaps using the TEST pin) and perform
recovery/”limp home” actions.
Error Recovery
If errors are detected on multiple occasions or a Host timeout occurs, the BLIC should be reset by lowering RESET or
stopping the CLK (or setting NXT if the RESET or CLK pin is
not controllable), and DS2-0 should be re-initialized in the
Control Register.
10. The Host attempts to transmit a single byte (Type 1 or
Type 2) IFR by setting ACK but without using the long
form of RDY for the first byte transfer.
11. The Host asserts STAT during a data byte transfer.
If resetting the BLIC doesn’t eliminate the error condition, a
test procedure should be entered using TEST and loopback
modes.
12. While transmitting, a Status/Control Register transfer is in
progress when a data byte transfer begins.
13. A transition has occurred on the VPWOUT pin and the
reflected transition has not been detected on VPWIN
(echo fail).
14. A failure occurs during TEST mode.
15. A low pulse <7µs occurs on VPWIN during the POWERDOWN mode.
Errors Which Don’t Set the ERR Flag
Due to various considerations, some errors which the user
might otherwise expect to be trapped by ERR are not. These
include:
1.
A zero length message (SOF followed by EOD) will not set
ERR, but will set the CRC flag.
2.
Any symbol, other than a noise pulse, is ignored while
17
HIP7010
PA3
OSCOUT
PA2
PA1
PA0
TCAP
SCK
MOSI
MISO
SS
RESET
STAT
RDY
IDLE
SCK
SOUT
SIN
SACTIVE
6805 MICROCONTROLLER
CLK
+5V
HIP7010 BLIC
VPWIN
LB EN
TEST
5.1KΩ
VPWIN
TX
RX
BUS OUT
BATT
J1850 BUS
TRANSCEIVER
R/F
43V
MOV
M1
C1
0.1µF
C2
0.01µF
C3
0.01µF
RS
57KΩ
RBUS
RF
BUS IN
GND
J1850 BUS
11KΩ/1KΩ
Ro 10Ω
330/3300pF
CBUS
FIGURE 8.
18
15KΩ
HIP7010
Dual-In-Line Plastic Packages (PDIP)
E14.3 (JEDEC MS-001-AA ISSUE D)
N
14 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
SYMBOL
-B-
A2
-C-
SEATING
PLANE
e
B1
D1
B
0.010 (0.25) M
A1
eC
C A B S
MAX
NOTES
-
0.210
-
5.33
4
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8
eA
C
0.008
0.014
0.204
0.355
-
D
0.735
0.775
18.66
D1
0.005
-
0.13
A
L
D1
MIN
A
E
D
MAX
A1
-ABASE
PLANE
MILLIMETERS
MIN
C
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
-
5
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
2.54 BSC
-
eA
0.300 BSC
7.62 BSC
6
eB
-
0.430
-
10.92
7
L
0.115
0.150
2.93
3.81
4
N
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
19.68
14
14
9
Rev. 0 12/93
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
19
HIP7010
Small Outline Plastic Packages (SOIC)
M14.15 (JEDEC MS-012-AB ISSUE C)
N
14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B1
2
3
L
SEATING PLANE
-A-
h x 45o
A
D
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
B S
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.3367
0.3444
8.55
8.75
3
E
0.1497
0.1574
3.80
4.00
4
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
8o
0o
N
α
NOTES:
MILLIMETERS
MAX
A1
e
α
MIN
14
0o
14
7
8o
Rev. 0 12/93
1. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.15mm (0.006 inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010
inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
20
ASIA
Intersil (Taiwan) Ltd.
Taiwan Limited
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029