Explorer 8 Development Board User's Guide

Explorer 8 Development Board
User’s Guide
 2015-2016 Microchip Technology Inc.
DS40001812B
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code
Generation, PICDEM, PICDEM.net, PICkit, PICtail,
RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2015-2016, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
ISBN: 978-1-5224-0346-3
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
DS40001812B-page 2
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 5
Chapter 1. Overview
1.1 Introduction ................................................................................................... 11
1.2 Development Kit Contents ............................................................................ 11
1.3 Explorer 8 Development Board .................................................................... 12
1.4 On-Board Jumper Configurations ................................................................. 13
1.5 Sample Devices ........................................................................................... 17
1.6 Sample Programs ......................................................................................... 17
Chapter 2. Getting Started
2.1 Explorer 8 with Preprogrammed Device ....................................................... 19
2.2 Board with PIM Attached Devices ................................................................ 21
2.3 Programming the Microcontrollers ............................................................... 21
2.3.1 Programming Requirements ...................................................................... 21
2.3.2 Opening the Program in MPLAB® X IDE ................................................... 22
2.3.3 Programming the Microcontroller .............................................................. 23
2.4 Connecting to Host PC for USB Communication ......................................... 24
2.4.1 USB-to-UART Interface ............................................................................. 25
2.4.2 USB-to-I2C Interface ................................................................................. 25
2.5 Powering the Board ...................................................................................... 26
2.5.1 External 9V Power Supply ......................................................................... 26
2.5.2 USB Power ................................................................................................ 26
2.6 Selecting Vdd Values ................................................................................... 27
2.6.1 Varying the Device Voltage ....................................................................... 27
2.6.2 Calculating other Vdd Values .................................................................... 27
Chapter 3. Tutorial Program
3.1 Tutorial Program Operation .......................................................................... 29
3.2 Source Code and Data Sheets ..................................................................... 31
Appendix A. Hardware Details
A.1 Hardware Elements ..................................................................................... 33
A.1.1 Processor Sockets .................................................................................... 33
A.1.2 Display ...................................................................................................... 33
A.1.3 Power Supply ............................................................................................ 33
A.1.4 Micro USB Port ......................................................................................... 34
A.1.5 Switches .................................................................................................... 34
A.1.6 Oscillator Options ...................................................................................... 34
A.1.7 Analog Input (Potentiometer) .................................................................... 34
A.1.8 ICD Connector .......................................................................................... 34
A.1.9 PICkit™ Connector .................................................................................... 34
A.1.10 PICtail™ and PICtail Plus Expansion Connectors ................................... 35
A.1.11 mikroBUS™ Connectors .......................................................................... 35
 2015-2016 Microchip Technology Inc.
DS40001812B-page 3
Explorer 8 Development Board User’s Guide
A.1.12 Pmod™ Connectors .................................................................................35
A.1.13 Configurable In-line Connector ................................................................35
A.1.14 LCD .........................................................................................................35
A.1.15 Sample Devices .......................................................................................36
A.2 Board Layout and Schematics ..................................................................... 37
Worldwide Sales and Service .....................................................................................41
DS40001812B-page 4
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Preface
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and
documentation are constantly evolving to meet customer needs, so some actual dialogs
and/or tool descriptions may differ from those in this document. Please refer to our website
(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each
page, in front of the page number. The numbering convention for the DS number is
“DSXXXXXXXXA”, where “XXXXXXXX” is the document number and “A” is the revision level
of the document.
For the most up-to-date information on development tools, see the MPLAB® IDE online help.
Select the Help menu, and then Topics to open a list of available online help files.
INTRODUCTION
This chapter contains general information that will be useful to know before using the
Explorer 8 Development Board. Items discussed in this chapter include:
•
•
•
•
•
•
•
•
Document Layout
Conventions Used in this Guide
Warranty Registration
Recommended Reading
The Microchip Website
Development Systems Customer Change Notification Service
Customer Support
Document Revision History
DOCUMENT LAYOUT
This document describes how to use the Explorer 8 Development Board as a tool to
emulate and debug firmware on a target board. The document is organized as follows:
•
•
•
•
Chapter 1. Overview
Chapter 2. Getting Started
Chapter 3. Tutorial Program
Appendix A. Hardware Details
 2015-2016 Microchip Technology Inc.
DS40001812B-page 5
Explorer 8 Development Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENT CONVENTIONS
Description
Represents
Examples
Arial font:
MPLAB® IDE User’s Guide
Italic characters
Referenced books
Emphasized text
...is the only compiler...
Initial caps
A window
the Output window
A dialog
the Settings dialog
A menu selection
select Enable Programmer
Quotes
A field name in a window or
dialog
“Save project before build”
Underlined, italic text with
right angle bracket
A menu path
File>Save
Bold characters
A dialog button
Click OK
A tab
Click the Power tab
N‘Rnnnn
A number in verilog format,
4‘b0010, 2‘hF1
where N is the total number of
digits, R is the radix and n is a
digit.
Text in angle brackets < >
A key on the keyboard
Press <Enter>, <F1>
Sample source code
#define START
Filenames
autoexec.bat
File paths
c:\mcc18\h
Keywords
_asm, _endasm, static
Command-line options
-Opa+, -Opa-
Bit values
0, 1
Courier New font:
Plain Courier New
DS40001812B-page 6
Constants
0xFF, ‘A’
Italic Courier New
A variable argument
file.o, where file can be
any valid filename
Square brackets [ ]
Optional arguments
mcc18 [options] file
[options]
Curly brackets and pipe
character: { | }
Choice of mutually exclusive
arguments; an OR selection
errorlevel {0|1}
Ellipses...
Replaces repeated text
var_name [,
var_name...]
Represents code supplied by
user
void main (void)
{ ...
}
 2015-2016 Microchip Technology Inc.
Preface
WARRANTY REGISTRATION
Please complete the enclosed Warranty Registration Card and mail it promptly.
Sending in the Warranty Registration Card entitles users to receive new product
updates. Interim software releases are available at the Microchip website.
RECOMMENDED READING
This user’s guide describes how to use the Explorer 8 Development Board. The
following documents are available and recommended as supplemental reference
resources.
Explorer 8 Development Board Layout and Schematic Quick Start Guide
(DS40001805)
This quick start guide provides a brief overview on the Explorer 8 Development Board’s
functionalities, features and capabilities.
MPLAB® ICD 3 In-Circuit Debugger User’s Guide (DS51766)
This document provides all the necessary information on the MPLAB ICD 3 In-Circuit
Debugger’s operation, installation, general setup and tutorial details. The MPLAB ICD
3 is a cost-effective, high-speed hardware debugger/programmer developed by
Microchip for PIC® microcontrollers and Digital Signal Controllers (DSCs).
MPLAB® REAL ICE™ In-Circuit Emulator User’s Guide for MPLAB X IDE
(DS50002085)
This user’s guide describes how to use the MPLAB REAL ICE In-Circuit Emulator as a
development tool to emulate and debug firmware on a target board, as well as how to
program devices. It provides details on the emulator’s operation, features,
troubleshooting, software, hardware reference and emulator accessories.
PICkit™ 3 In-Circuit Debugger/Programmer User’s Guide for MPLAB® X IDE
(DS52116)
This user’s guide describes the PICkit 3 In-Circuit Debugger/Programmer’s operation,
usage, troubleshooting methods and hardware specifications. The PICkit 3 can be
implemented as a debugger or development programmer for Microchip PIC MCUs and
DSCs that are based on In-Circuit Serial Programming™ (ICSP™) and Enhanced
ICSP 2-wire serial interfaces.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 7
Explorer 8 Development Board User’s Guide
THE MICROCHIP WEBSITE
Microchip provides online support via our website at www.microchip.com. This website
is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the website contains the following information:
• Product Support – Data sheets and errata, application notes and sample
programs, design resources, user’s guides and hardware support documents,
latest software releases and archived software.
• General Technical Support – Frequently Asked Questions (FAQs), technical
support requests, online discussion groups, Microchip consultant program
member listing.
• Business of Microchip – Product selector and ordering guides, latest Microchip
press releases, listing of seminars and events, listings of Microchip sales offices,
distributors and factory representatives.
DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip
products. Subscribers will receive e-mail notification whenever there are changes,
updates, revisions or errata related to a specified product family or development tool of
interest.
To register, access the Microchip website at www.microchip.com, click on Customer
Change Notification and follow the registration instructions.
The Development Systems product group categories are:
• Compilers – The latest information on Microchip C compilers, assemblers, linkers
and other language tools. These include the MPLAB XC Compilers that support
all 8-, 16- and 32-bit PIC MCUs and dsPIC® DSCs.
• Emulators – The latest information on Microchip in-circuit emulators. This
includes the MPLAB REAL ICE In-Circuit Emulator.
• In-Circuit Debuggers – The latest information on the Microchip in-circuit
debuggers. This includes the MPLAB ICD 3 In-Circuit Debugger and the PICkit 3
In-Circuit Debugger.
• MPLAB® X IDE – The latest information on Microchip MPLAB X IDE, the
Integrated Development Environment for development systems tools which can
be run on Windows®, Mac OS® and LINUX® operating systems.
• Programmers – The latest information on Microchip programmers. These include
the device (production) programmers MPLAB REAL ICE in-circuit emulator and
MPLAB ICD 3 in-circuit debugger, and the development (non-production)
programmer PICkit 3.
DS40001812B-page 8
 2015-2016 Microchip Technology Inc.
Preface
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
Customers should contact their distributor, representative or field application engineer
(FAE) for support. Local sales offices are also available to help customers.
Technical support is available through the website at:
http://www.microchip.com/support.
DOCUMENT REVISION HISTORY
Revision A (August, 2015)
Initial release of the document.
Revision B (March, 2016)
Updated schematics.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 9
Explorer 8 Development Board User’s Guide
NOTES:
DS40001812B-page 10
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Chapter 1. Overview
1.1
INTRODUCTION
The Explorer 8 Development Board is one of the latest development boards for
evaluating and demonstrating the capabilities and features of Microchip’s 8-bit PIC®
MCUs. This board supports 8/14/20/28/40-pin DIP and 44/64/80-pin PIM-mounted PIC
MCUs.
This board is fully populated with two fixed and one variable power supply, a 16x2
Character LCD module, a pair of mikroBUS™ Click™ board headers to accommodate
a variety of plug-in modules, a pair of Digilent Pmod™ connectors, an in-line
completely configurable connector, PICtail™ connectors and a USB-to-serial/I2C
converter. The Explorer 8 is fully compatible with the MPLAB® Code Configurator and
MPLAB X v3.00 or later.
1.2
DEVELOPMENT KIT CONTENTS
The Explorer 8 Development Board comes with the following:
• Explorer 8 Development Board (DM160228)
• Pre-programmed DSTEMP
• Micro USB cable
If the kit is missing any of these parts, please contact the nearest Microchip sales office
listed in the back of this publication.
The MPLAB X Integrated Development Environment (IDE) is a free, integrated
software tool set for application development and debugging. Compilers and other
board-compatible software and hardware tools can be purchased.
To download the MPLAB X IDE software and documentation, or get information on the
other tools, visit www.microchip.com/devtools.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 11
Explorer 8 Development Board User’s Guide
1.3
EXPLORER 8 DEVELOPMENT BOARD
The Explorer 8 Development Board has the following hardware features. Each
feature’s number corresponds to the number in Figure 1-1, showing the feature’s
location on the board:
1. MCP2221 USB-to-UART/I2C serial converter (U3)
2. 16x2 Character LCD (LCD1)
3. MCP23S17 I/O Expander for LCD Interface (U4)
4. Eight blue LEDs (D1 to D8).
5. Male header pins for attaching Plug-in-Modules (U1A)
6. Socket for attaching 40-pin PIC MCUs (J8)
7. Socket for attaching 28-pin PIC MCUs (J13)
8. Socket for attaching 8/14/20-pin PIC MCUs (J10)
9. mikroBUS headers for attaching mikroBUS compatible boards (J32 and J35)
10. Two push button switches for external stimulus (S1 and S2)
11. PICtail Expansion Connectors for PICtail Daughter Boards (J3, J5, J11 and J28)
12. PICtail Plus Card Edge Modular Expansion Connectors for PICtail Plus Daughter
Boards (J19)
13. Test Points for 5.0V (TP1 and TP7), 3.3V (TP6) and V_VAR (TP5). V_VAR is the
variable voltage and is equal to the device VDD and its associated logic
14. 20-pin in-line expansion connector (J33)
15. 8 MHz crystal for device external oscillator (Y1)
16. Digilent Pmod compatible connectors (J17 and J20)
17. 10 kΩ Potentiometer for analog inputs (R25)
18. Variable Power Indicator LED (D9)
19. 3.3V Power Indicator (LD2)
20. 5.0V Power Indicator (LD1)
21. 5.0V (U5), 3.3V (U1) and Variable (U2) power supplies
22. Barrel connector for 9V DC Supply (J1)
23. RJ11 connector for ICSP programming/debugging using REAL ICE and ICD 3
(J26)
24. 6-pin male header for ICSP programming/debugging using PICkit 3 (J12)
25. Push button switch on MCLR for external Reset (S3)
26. Micro USB socket for USB communication and/or USB power (J18)
DS40001812B-page 12
 2015-2016 Microchip Technology Inc.
FIGURE 1-1:
EXPLORER 8 DEVELOPMENT BOARD
2
1
3
4
5
6
8
7
9
10
26
11
25
24
12
23
22
13
20 19 18 17
21
1.4
16
15
14
ON-BOARD JUMPER CONFIGURATIONS
The Explorer 8 Development Board allows the user to connect or disconnect
components from PIC MCU pins or from other on-board components through
associated jumpers. Table 1-1 and Figure 1-2 provide details and examples for these
connections.
TABLE 1-1:
Label
ON-BOARD JUMPERS DESCRIPTION AND SAMPLE
CONFIGURATION
Jumper/s
Description
Configuration
MCU Interface to MCP2221 USB-to-I2C/UART Converter(1)
1
J22
Pulls up the configured I2C SCL pin
(see J57) and SDA pin (see J58).
2
J57
Connects the microcontroller I2C SCL
pin to the MCP2221 SCL pin (see
Label 3).
E.g. RC3 is configured as the
microcontroller I2C SCL pin.
RB6
J58
Connects the microcontroller I2C SDA
pin to the MCP2221 SDA pin (see
Label 3).
E.g. RC4 is configured as the
microcontroller I2C SDA pin.
RB4
J23
Connects the microcontroller I2C SCL
and SDA pins to the MCP2221 SCL
and SDA pins, respectively.
3
SDA
SCL
RC3
RC4
SCL SDA
 2015-2016 Microchip Technology Inc.
DS40001812B-page 13
Explorer 8 Development Board User’s Guide
TABLE 1-1:
Label
4
ON-BOARD JUMPERS DESCRIPTION AND SAMPLE
CONFIGURATION (CONTINUED)
Jumper/s
J53, J55
J54, J56
Description
Connects the microcontroller UART
RX pin to the MCP2221 TX pin.
E.g. RC7 is configured as the
microcontroller RX pin.
Connects the microcontroller UART
TX pin to the MCP2221 RX pin.
E.g. RC6 is configured as the
microcontroller TX pin.
MCU Interface to MCP23S17 I/O Expander
5
Configuration
J53
J55
RB5
RC5
RC7
J54
RC4
J56
RB7
RC6
(1)
J60
Connects RB5 to the MCP23S17 I/O
Expander RESET pin.
J59
Connects RA2 to the MCP23S17 I/O
Expander Chip Select (CS) pin.
LCD_RESET
J59
MCU Interface to the LEDs(1)
6
J7
J21
Connects LEDs D1 to D4 cathodes to
ground to provide a continuous LED
current path.
Connects LEDs D5 to D8 cathodes to
ground to provide a continuous LED
current path.
LED_D_EN
LED_B_EN
MCU Interface to J32 mikroBUS™(1)
7
J45
J46
J47
8
J27, J43
J34, J44
DS40001812B-page 14
Connects the microcontroller SDO pin
to the J32 mikroBUS MOSI (SPI
Master Output Slave Input) pin.
E.g. RC5 is configured as the
microcontroller SDO pin.
Connects the microcontroller SDI pin
to the J32 mikroBUS MISO (SPI
Master Input Slave Output) pin
E.g. RC4 is configured as the
microcontroller SDI pin.
RD4
RC5
RD5
RC4
Connects the microcontroller SCK pin
to the J32 mikroBUS SCK (SPI Clock)
pin.
E.g. RC3 is configured as the
microcontroller SCK pin.
RD6
Connects the microcontroller RX pin to
the J32 mikroBUS UART RX pin.
E.g. RC7 is configured as the
microcontroller RX pin.
J43
RG2
J27
Connects the microcontroller TX pin to
the J32 mikroBUS UART TX pin.
E.g. RC6 is configured as the
microcontroller TX pin.
RC3
RB5
RC7
RG1
J44
J34
RB7
RC6
 2015-2016 Microchip Technology Inc.
TABLE 1-1:
Label
ON-BOARD JUMPERS DESCRIPTION AND SAMPLE
CONFIGURATION (CONTINUED)
Jumper/s
Description
Configuration
MCU Interface to J35 mikroBUS(1)
9
J48
J49
J50
10
J41
J42
Connects the microcontroller SDO pin
to the J35 mikroBUS MOSI (SPI
Master Output Slave Input) pin.
E.g. RC5 is configured as the
microcontroller SDO pin.
RC7
Connects the microcontroller SDI pin
to the J35 mikroBUS MISO (SPI
Master Input Slave Output) pin.
E.g. RC4 is configured as the
microcontroller SDI pin.
RB4
Connects the microcontroller SCK pin
to the J35 mikroBUS SCK (SPI Clock)
pin.
E.g. RC3 is configured as the
microcontroller SCK pin.
RB6
Connects the microcontroller RX pin to
the J35 mikroBUS UART RX pin.
E.g. RC7 is configured as the
microcontroller RX pin.
RC5
Connects the microcontroller TX pin to
the J35 mikroBUS UART TX pin.
E.g. RC6 is configured as the
microcontroller TX pin.
RC4
RC5
RC4
RC3
RC7
RC6
Other Connections and Interfaces(1)
11
12
13
14
15
 2015-2016 Microchip Technology Inc.
J4, J31
J37
J36
J15, J16
J14, J30
Connections depend whether RA5
and RA4 are configured as an I/O port
or as a VCAP pin.
E.g. RA5 is configured as an I/O port
while RA4 as a VCAP pin.
RA5 VCAP
J4
J31
RA4 VCAP
Selects whether RA6 or the RA5 pin
be connected to the external 8 MHz
crystal (Y1).
E.g. The 8 MHz crystal is connected to
the MCU OSC2/RA5 pin.
RA5
Selects whether RA7 or the RA4 pin
be connected to the external 8 MHz
crystal (Y1).
E.g. The 8 MHz crystal is connected to
the MCU OSC1/RA7 pin.
RA7
Option to power the Digilent Pmod
with 3.3V or 5V.
E.g. J17 Pmod is supplied with 5V
while J20 Pmod is supplied with 3.3V
Selects either 3.3V, 5.0V or a variable
voltage for the board’s supply
E.g. The board is supplied with 5V.
RA6
RA4
J15 J16
+5V
+5V
+3.3V
+3.3V
J14
J30
V_VAR
+5V
DS40001812B-page 15
Explorer 8 Development Board User’s Guide
TABLE 1-1:
Label
16
Jumper/s
J2
17
J51, J52
Description
Configuration
Selects whether to supply 5V power to
the board via USB or the output of the
5V regulator.
E.g. The board is USB-powered.
USB
+5V
Connects the PGD and PGC pins of
the PICkit™ 3, ICD 3 or REAL ICE™
to the PIC® MCU ICSPDAT and
ICSPCLK, respectively for ICSP™
programming
J52 J51
RB6
RB7
BRD
+5V
RA1
RA0
18
J61
Connects the LCD VDD pin to +5V
supply.
LCD_PWR
19
J24
To supply a regulated 3.3V output.
J24
Note 1:
FIGURE 1-2:
ON-BOARD JUMPERS DESCRIPTION AND SAMPLE
CONFIGURATION (CONTINUED)
Sample configurations only. Jumpers should always be disconnected for unused
interfaces and devices.
EXPLORER 8 DEVELOPMENT BOARD JUMPER LOCATIONS
1
2
3
4
5
6
7
8
9
10
19
11
18
17
16
15
DS40001812B-page 16
14
13
12
 2015-2016 Microchip Technology Inc.
1.5
SAMPLE DEVICES
The Explorer 8 Development Board comes with a 40-pin DSTEMP.
1.6
SAMPLE PROGRAMS
The Explorer 8 Development Board demonstration program can be downloaded from
the Microchip website (www.microchip.com/explorer8). This Demo Code can be used
with the included sample device and with a REAL ICE (In-Circuit Emulator), MPLAB
ICD 3 (programmer/debugger) or with a PICkit 3 (programmer/debugger).The Demo
code was developed using the MPLAB Code Configurator (MCC). For more
information on MCC, visit www.microchip.com/mcc.
For a complete list of available sample programs, schematics and additional collateral
for the Explorer 8 Development Board, visit www.microchip.com/explorer8.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 17
Explorer 8 Development Board User’s Guide
NOTES:
DS40001812B-page 18
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Chapter 2. Getting Started
The Explorer 8 Demo Board is very flexible and may be used in a variety of ways. This
section provides the different configurations of the board, and the required tools and
equipment for each of them.
2.1
EXPLORER 8 WITH PREPROGRAMMED DEVICE
Several features of the Explorer 8 Demo Board can be demonstrated immediately by
following the steps listed below:
1. Place the preprogrammed DSTEMP on the 40-pin socket of the Explorer 8
Development Board.
2. Ensure that the jumpers are on their proper configuration as shown in Table 2-1.
See Section 1.4 “On-Board Jumper Configurations” for jumper description
and location.
Note:
The table contains only a list of jumpers that are required to be setup for
proper demonstration of the Explorer 8 Development Board using the
pre-programmed device. Jumpers not listed in the table will have no effect
on the demo program.
TABLE 2-1:
Jumper/s
J2
JUMPER SETUP USING THE PRE-PROGRAMMED DEVICE
Description
Configuration
Power the board via USB
USB
+5V
BRD
+5V
J4
Use RA5 as an I/O pin
RA5
VCAP
J7
Use LEDs D4 through D1
LED_D_EN
J14
Use +5.0V Supply
+3.3V
+5V
J21
Use LEDs D8 through D5
LED_B_EN
J36
Connect the 8 MHz Crystal to the device OSC1
pin to function as primary oscillator
RA7
RA4
 2015-2016 Microchip Technology Inc.
DS40001812B-page 19
Explorer 8 Development Board User’s Guide
TABLE 2-1:
Jumper/s
J37
JUMPER SETUP USING THE PRE-PROGRAMMED DEVICE
Description
Configuration
Connect the 8 MHz Crystal to the device OSC2
pin to function as primary oscillator
RA5
RA6
J51
For ICSP™ programming, connect the device to
the PGD pin of PICkit™ 3, ICD 3 or REAL ICE™
RB7
RA0
J52
For ICSP programming, connect the device to
the PGC pin of PICkit™ 3, ICD 3 or REAL ICE™
RB6
RA1
J54
For USB-to-UART communication
RC4
RC6
J59
To send data to the LCD
J59
J60
To reset the MCP23S17 I/O Expander
LCD_RESET
J61
Power the LCD module
LCD_PWR
3. Apply power to the Explorer 8 Development Board using the Micro USB cable
that comes with the kit. See Section 2.6 “Selecting Vdd Values”.
The device can now be demonstrated using the tutorial program. See
Section 3.1 “Tutorial Program Operation”.
DS40001812B-page 20
 2015-2016 Microchip Technology Inc.
2.2
BOARD WITH PIM ATTACHED DEVICES
The Explorer 8 Development Board can also be used to demonstrate PIM-mounted
8-bit PIC microcontrollers. A Plug-in-Module (PIM) enables the attachment of
44/64/80-pin devices to the board.
To attach a PIM, simply seat the PIM in the 84-pin, elevated male connectors as shown
in Figure 2-1.
FIGURE 2-1:
84-PIN HEADER FOR PLUG-IN-MODULE (PIM)
Make sure that the device mounted on the PIM is supplied with the appropriate voltage.
See Section 2.6 “Selecting Vdd Values” and Section 2.6.2 “Calculating other Vdd
Values” for supplies other than 5V and 3.3V.
Some PIMs also enable the board’s 5V output to be automatically reset to 3.3V.
For a list of microcontroller-compatible PIMs, go to www.microchip.com.
2.3
PROGRAMMING THE MICROCONTROLLERS
The Explorer 8 Development Board supports the ability to program a microcontroller
through multiple options.
This section discusses:
• Programming Requirements
• Opening the Program in MPLAB X IDE
• Programming the Microcontroller Using ICD 3, REAL ICE and PICkit 3
2.3.1
Programming Requirements
To reprogram a sample device, the following are required:
• Program source code – The sample code is pre-loaded on the device, but user
source code can be substituted. If this is done, the sample program can be
restored by downloading the MPLAB X project file available at the Microchip
website.
• An assembler or compiler – The source code must be assembled or compiled
into a hex file before it can be programmed into the device.
• A programmer – Once the code is in the hex file format, this device programs the
microcontroller’s Flash memory. If the code protection bit(s) have not been
programmed, the on-chip program memory can be read out for verification
purposes.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 21
Explorer 8 Development Board User’s Guide
In meeting these requirements, the following items are to be taken into consideration:
• Code development and debugging – The free MPLAB X IDE software
development tool includes a debugger and several other software tools as well as
a unified graphical user interface (GUI) for working with other Microchip and
third-party software and hardware tools.
• Assembler – The free MPLAB X IDE tool includes the MPASM™ assembler.
• Compiler – Microchip’s MPLAB® XC8 Compiler is fully integrated for the MPLAB
X IDE environment.
• Programmer – Microchip’s MPLAB In-Circuit Debugger (ICD) 3, PICkit 3 In-Circuit
Debugger/Programmer, or MPLAB REAL ICE In-Circuit Emulator can be used to
program the device and all are fully integrated for the MPLAB X IDE environment.
• The MPLAB Code Configurator (MCC) – is Microchip’s new tool for developing
drivers and initializers featuring a very easy to use GUI. It is a free tool that integrates into MPLAB X, providing a very powerful development platform. For more
information on MCC go to (www.microchip.com/mcc).
The MPLAB X IDE and the XC8 Compiler can be downloaded from the Microchip
website.
For a list of tools compatible with PIC microcontrollers, see the Microchip Development
Tools website at www.microchip.com/devtools.
2.3.2
Opening the Program in MPLAB® X IDE
The MPLAB X Integrated Development Environment (IDE) is a software program that
runs on Windows®, MAC OS® and Linux® to develop code for PIC microcontrollers and
Digital Signal Controllers (DSC).
This section describes how to open the Explorer_8_Demo_MCC.X project in MPLAB
X IDE.
1. Download the Explorer_8_Demo_MCC project from Microchip’s Explorer 8 web
page (www.microchip.com/explorer8).
2. Launch the MPLAB X IDE application and select File>Open Project>
Explorer_8_Demo_MCC.X >Open Project from the downloaded section. The
project file will appear on the Projects area. If it is not the main project, set as
main project.
3. Right click. Explorer_8_Demo_MCC.X >Set as main project.
4. If not already downloaded, download and install the MCC tool from the Plugins
repository. This is done by the following:
• Select Tools from the MPLAB X menu, then Plugins.
• Select the Available Plugins tab and select the MPLAB Code Configurator
• Go through the install process.
5. Once installed, go to the Tools menu in MPLAB X, select Embedded then MPLAB
Code Configurator.
6. With MCC open, all the modules currently in the project used for the demo
application can be seen.
7. The device is now ready to be built and programmed.
The next section will describe how to load the program into the microcontroller.
DS40001812B-page 22
 2015-2016 Microchip Technology Inc.
2.3.3
Programming the Microcontroller
Program the device using an ICD 3, REAL ICE or PICkit 3.
1. Connect the ICD 3 or REAL ICE as shown in Figure 2-2. For PICkit 3, see
Figure 2-3.
2. Setup the jumpers. In addition to the jumper settings listed in
Section 2.1 “Explorer 8 with PreProgrammed Device”, J51 and J52 should
also be configured. See Figure 2-2.
3. Power-up the Explorer 8 Development Board (see Section 2.5 “Powering the
Board”).
4. Open the project on MPLAB X IDE (see Section 2.3.2 “Opening the Program
in MPLAB® X IDE”).
5. Right click Explorer_8_Demo_MCC.X >Properties. A pop-up window will appear
as shown in Figure 2-4.
FIGURE 2-2:
ICD 3 CONNECTION AND JUMPER CONFIGURATION
J52
2 J51
FIGURE 2-3:
RB6
RB7
RA1
RA0
PICkit™ 3 CONNECTION AND JUMPER CONFIGURATION
J52
2 J51
 2015-2016 Microchip Technology Inc.
RB6
RB7
RA1
RA0
DS40001812B-page 23
Explorer 8 Development Board User’s Guide
FIGURE 2-4:
PROJECT PROPERTIES WINDOW IN MPLAB® X IDE
6. Select the XC8 compiler under the Compiler Tool chain, if not already selected.
7. Under Hardware Tool, click ICD 3, REAL ICE or PICkit 3, depending upon the
connected programmer.
8. Click Apply, and then OK.
9. To load the program to the DSTEMP device, click the Make and Program
Device icon.
2.4
CONNECTING TO HOST PC FOR USB COMMUNICATION
The Explorer 8 Development Board allows the device to communicate with a PC via
two interfaces: USB-to-UART and USB-to-I2C. An on-board USB 2.0 to I2C/UART
Protocol Converter (MCP2221) is provided for this purpose. The MCP2221 supports
Windows® (XP and later versions), Linux® and Mac OS® (all versions) operating
systems. Drivers can be downloaded from the Microchip website at
www.microchip.com/mcp2221.
After installing the MCP2221 driver, the board can now be connected to the host PC
through a USB cable provided in the Explorer 8 Development Board kit.
DS40001812B-page 24
 2015-2016 Microchip Technology Inc.
2.4.1
USB-to-UART Interface
The MCP2221 supports baud rates between 300 and 115200. It utilizes a set of
commands to read and set the UART parameters during operation. It only supports
eight Data bits, no Parity, and one Stop bit. The terminal program (e.g., Teraterm,
Realterm, etc.) must be configured with the same settings.
If the MCU is configured to communicate with the host PC via UART interface, jumpers
J53, J54, J55 and J56 must be setup properly. The tutorial program in the DSTEMP
implements the UART for MCU-to-PC communication. Figure 2-5 shows how to setup
the jumpers for the tutorial program. The MCU is configured for Transmit mode so only
J54 is utilized and the other jumpers are left disconnected.
FIGURE 2-5:
SETUP FOR UART TRANSMIT MODE
J54
RC4
RC6
The operating system searches for a driver once the Explorer 8 Development Board is
connected to the PC using the USB-to-UART interface. After a suitable driver is found,
the system creates an entry in the registry. The entry stores relevant information about
the USB-to-UART adapter, its driver and the associated COM port.
2.4.2
USB-to-I2C Interface
For the USB-to-I2C interface, the MCP2221 functions as an I2C Master to the PIC MCU
and uses USB HID (Human Interface Device) protocol for communication with a host
PC. A typical command exchange starts with a 64-byte packet that is written by the host
PC. Afterward, the PC reads the response USB-to-I2C from the device as a 64-byte
packet.
To use the Explorer 8 Development Board for I2C interface, jumpers J22, J23, J57 and
J58 must be configured properly. See Labels 1, 2 and 3 of Table 1-1 for sample jumper
configurations.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 25
Explorer 8 Development Board User’s Guide
2.5
POWERING THE BOARD
The Explorer 8 Development Board can be powered-up in two ways: External 9V DC
supply and USB power.
2.5.1
External 9V Power Supply
To power-up the board using an external 9V power supply:
• Plug the 9V power supply to a wall outlet.
• Connect the 9V power supply to the board through the barrel connector placed on
the lower left corner of the board.
• Place J2 in the position shown in Figure 2-6.
FIGURE 2-6:
USING THE 9V EXTERNAL SUPPLY
USB
+5V
J
J2
BRD
+5V
9V DC
One of the on-board regulators will reduce this voltage to 5V which can be measured
through Test Points TP1 and TP7. For 3.3V, the 5V output will be further reduced
through a 3.3V regulator. Make sure to attach J24 before measuring the 3.3V output at
TP6. The board also supports other voltage values through an adjustable voltage
regulator. The variable voltage can be measured through TP5. For more details on
varying the voltage values, see Section Section 2.6 “Selecting Vdd Values”.
2.5.2
USB Power
The Explorer 8 Development Board can also be powered through USB. The board will
draw +5V power from a host device such as a PC by connecting a USB cable between
the on-board micro USB socket and the PC’s USB port. The micro USB cable is
included in the Explorer 8 Development Kit.
Figure 2-7 shows how to connect the USB cable to the micro USB socket and J2 setting
for USB-powered configuration.
FIGURE 2-7:
USB-POWERED BOARD CONFIGURATION
To PC
USB Port
J2
USB
+5V
BRD
+5V
DS40001812B-page 26
 2015-2016 Microchip Technology Inc.
2.6
SELECTING VDD VALUES
The Explorer 8 Development Board is capable of supplying 5V, 3.3V and variable
supply voltages between 1.2 and 5V through dedicated on-board regulators. The
variable supply voltage, called V_VAR (also equal to VDD), is used to power the device
and the on-board components.
2.6.1
Varying the Device Voltage
Figure 2-8 shows the jumper configuration for the three voltage settings.
FIGURE 2-8:
JUMPER CONFIGURATION FOR DIFFERENT DEVICE
VOLTAGES
V_VAR = 5V
(Fixed)
V_VAR = 3.3V
(Fixed)
+3.3V
+3.3V
+3.3V
ADJ+V
ADJ+V
J30
+5V
J30
+5V
J14
2.6.2
V_VAR = ADJ + VREF
(Variable)
ADJ+V
J30
+5V
J14
J14
Calculating other VDD Values
For voltages other than 5V and 3.3V, jumpers J14 and J30 must be configured for
variable supply as shown in Figure 2-8. Other VDD values can be produced by the
LM317 adjustable voltage regulator by populating the PIM board’s R101 and R102 with
different value resistors. This section discusses how to calculate alternate values for
these resistors. For detailed information, see the LM317 data sheet.
Note:
R101 and R102 are named R1 and R2, respectively, in other PIM boards.
These must not be confused with the R1 and R2 values discussed in this
section.
EQUATION 2-1:
LM317 REGULATOR VOLTAGE OUTPUT
V
OUT
= V
 1 + R2
------- + I
 R2
ADJ
REF 
R1
IADJ is minimized by the LM317 and can be neglected or assumed to be zero. VREF is
the reference voltage developed by the LM317 between the output and adjustment
terminal, and is typically equal to 1.25V.
Therefore, the equation can be rewritten as shown in Equation 2-2.
EQUATION 2-2:
CALCULATING THE LM317 OUTPUT VOLTAGE
R2
V OUT = 1.25V  1 + -------

R1
Where:
 R20  R102 
R2 = R20  R102 = --------------------------------- R20 + R102 
 R19  R101 
R1 = R19  R101 = --------------------------------- R19 + R101 
 2015-2016 Microchip Technology Inc.
DS40001812B-page 27
Explorer 8 Development Board User’s Guide
The Explorer 8 Development Board’s R20 and R19 resistors have their default values
of 1 kΩ and 330Ω, respectively. Without R102 and R101 being inserted in parallel on
the PIM board, VOUT = 1.25V(1 + 1 kΩ/330Ω) = 5.04V.
To calculate a desired VOUT:
1. Solve for R2, given R1 = R19 = 330Ω.
2. Now knowing R2 and R20, solve for R102.
3. Determine the nearest available resistor value for R102 and recalculate the
resulting V_VAR to make sure it does not exceed the maximum VDD for the part
being used.
For devices that are not mounted on a PIM but need a supply voltage other than 5V or
3.3V, external resistors may be connected to the ADJ pin of J29. A resistor connected
between ADJ and ground is equivalent to R102 and a resistor connected between ADJ
and V_VAR is equivalent to R101. Calculate the resistor values using the equations
previously discussed in this section.
DS40001812B-page 28
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Chapter 3. Tutorial Program
The tutorial program is preprogrammed into the DSTEMP that comes with the Explorer
8 demo board. This program, which can be downloaded from the Microchip website
(www.microchip.com/explorer8), is built using the MPLAB X IDE and the MPLAB XC8
Complier. It also utilizes the macros, drivers and initializers generated by the MPLAB®
Code Configurator (MCC). MCC is a plug-in for MPLAB X IDE that generates
seamless, easy to understand drivers and initializers that are inserted into your project.
For more information on MCC, visit www.microchip.com/mcc.
3.1
TUTORIAL PROGRAM OPERATION
The tutorial program consists of three components: Voltmeter, LED Toggle and LED
dimming. The flowchart in Figure 3-1 illustrates the button navigation through the entire
program.
The different components are displayed on the LCD and the LEDs. The data sent to the
LCD is simultaneously transmitted by the EUSART module of the device to the
USB-to-UART/I2C converter and can, therefore, be viewed on the host PC monitor
through a serial terminal program (see Section 2.4 “Connecting to Host PC for USB
Communication”). Make sure that the terminal program is configured to 9600 Baud,
8-bit Data, No Parity and 1 Stop Bit. For the board supply and jumper configurations,
see Section 2.1 “Explorer 8 with Pre-Programmed Device”.
FIGURE 3-1:
TUTORIAL PROGRAM FLOWCHART
Power Up
Microchip
Explorer 8 Demo
Voltmeter
S1=Now S2=Next
Volts = x.xxV
S1=Exit
Toggle LEDs
S1=Now S2=Next
LEDs Toggle
S1=Exit
LED Dimming
S1=Now S2=Next
Turn POT R25
S1=Exit
 2015-2016 Microchip Technology Inc.
DS40001812B-page 29
Explorer 8 Development Board User’s Guide
To select menu options, use the S1 and S2 buttons on the board (see Figure 3-2).
FIGURE 3-2:
BUTTON SWITCHES FOR MENU SELECTION
When the board is powered up, a “Microchip Explorer 8 Demo” text is displayed on the
LCD and sent to the serial terminal as well. After a few seconds, the program proceeds
to the first component.
1. Voltmeter
This mode uses the Analog-to-Digital Converter (ADC) module to measure the voltage
across the R25 potentiometer and display a value between 0.00V and 5.00V on the
LCD. (In general, the displayed value is between 0.00V to V_VAR).
FIGURE 3-3:
VOLTMETER DISPLAY AND COMPONENT
The voltage reading is updated continuously until the mode is exited by pressing S1.
FIGURE 3-4:
VOLTAGE DISPLAY
2. LEDs Toggle
This mode toggles LEDs D1 and D2 alternately with D3 and D4 between fully On and
fully Off states every 100 milliseconds.
FIGURE 3-5:
DS40001812B-page 30
LED TOGGLE DISPLAY
 2015-2016 Microchip Technology Inc.
3. LED Dimming
Both the Complementary Output Generator (COG) and Analog-to-Digital Converter
(ADC) modules are implemented in this mode. The COG produces a pulse-width
modulated output whose duty cycle is determined by the measured ADC value across
the R25 potentiometer. The COG output controls the brightness of the D6, D7 and D8
LEDs.
FIGURE 3-6:
LED DIMMING DISPLAY
Turning the potentiometer clockwise increases the brightness of the LEDs while
rotating it counterclockwise dims the LEDs.
FIGURE 3-7:
LED DIMMING
Exiting this mode by pressing S1 brings the program back to Voltmeter.
3.2
SOURCE CODE AND DATA SHEETS
The tutorial program is available on the Microchip website:
(www.microchip.com/explorer8)
The source codes and hex files are contained in the Explorer_8_Demo_MCC.X
project file.
For information on reprogramming the device with new or modified code, see
Section 2.3 “Programming the Microcontrollers”.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 31
Explorer 8 Development Board User’s Guide
NOTES:
DS40001812B-page 32
 2015-2016 Microchip Technology Inc.
EXPLORER 8 DEVELOPMENT BOARD
USER’S GUIDE
Appendix A. Hardware Details
A.1
HARDWARE ELEMENTS
A.1.1
Processor Sockets
The Explorer 8 Development Board contains four processor sockets:
•
•
•
•
20-pin Socket – for 8/14/20-pin DIP microcontrollers
28-pin Socket – for 28-pin DIP microcontrollers
40-pin Socket – for 40-pin DIP microcontrollers
84-pin PIM Socket – for 44/64/80-pin PIM-mounted microcontrollers
Only one device may be used at a time. Remove unnecessary devices before
demonstrating your program.
For a complete list of 8-bit PIC microcontrollers and available PIMs, go to the Microchip
website at www.microchip.com.
A.1.2
Display
Eight blue LEDs (D8:D1) are connected to the <RB3:RB0> and <RD3:RD0> pins of
each processor type, respectively. These pins are set high to light the LEDs.
LEDs D8:D5 may be disconnected by removing jumper J21 while LEDs D4:D1 may be
disconnected by removing J7.
D5 lights up once J21 is attached because RB0 is also connected to switch SW1 and
this pin is always pulled up to V_VAR.
A.1.3
Power Supply
The Explorer 8 Development Board does not come with a power supply but it comes
with a micro USB cable for powering the board via USB. Using USB power, however,
limits the supply to only 100 mA. Using the 9V external supply, both 3.3V and 5.0
supplies are capable of up to 1A. Microchip’s 9V, 1.3A power supply (Part Number
AC002014) can be used if external supply is needed. When using an external supply,
the board is limited to a maximum of 5A, imposed on the breadboard contacts.
The board is populated with two fixed (U5 and U1) and one variable (U2) voltage
regulators to provide 5.0V, 3.3V and any voltage between 1.2V and 5V.
Note:
For power supply selection, see Section 2.5 “Powering the Board” and
Section 2.6 “Selecting Vdd Values”.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 33
Explorer 8 Development Board User’s Guide
A.1.4
Micro USB Port
A micro USB port is provided not just for powering the board but also for
communications between the device and a host PC via USB. The micro USB cable
included in the Explorer 8 Development Board Kit can be used to connect the board’s
micro USB port to the host PC’s USB port.
The on-board MCP2221 is a USB-to-UART/I2C serial converter that enables USB
connectivity for devices with UART or I2C interfaces.
Note:
A.1.5
For details on this connection, see Section 2.4 “Connecting to Host PC
for USB Communication”.
Switches
Three switches are provided on the board:
• S1 – Active-low switch connected to RB0
• S2 – Active-low switch connected to RA5
• S3 – MCLR to hard reset the processor
When pressed, the switches are grounded. When idle, they are pulled high (V_VAR).
A.1.6
Oscillator Options
An 8 MHz crystal (Y1) serves as the controller’s primary oscillator. It can also be used
as TMR0’s clock source for some devices depending upon the configured J36 and J37
settings.
A.1.7
Analog Input (Potentiometer)
A 10 kΩ potentiometer (R25) is connected through a series resistor to RA0/AN0.
The potentiometer can be adjusted from V_VAR to GND to provide an analog input to
one of the device ADC channels.
A.1.8
ICD Connector
The MPLAB® ICD 3 can be connected to the modular connector (J26) for programming
and in-circuit debugging. Jumpers J51 and J52 define the connection of the in-circuit
debugger to the device pins. The MPLAB REAL ICE can also be connected to this
interface.
Note:
A.1.9
For details, see Section Section 2.3.3 “Programming the
Microcontroller”.
PICkit™ Connector
A PICkit 3 In-Circuit Debugger/Programmer can be connected to the 6-pin interface
provided by J12. Jumpers J51 and J52 define the connection of the PICkit3 to the
microcontroller pins.
Note:
DS40001812B-page 34
For details, see Section 2.4 “Connecting to Host PC for USB
Communication”.
 2015-2016 Microchip Technology Inc.
A.1.10
PICtail™ and PICtail Plus Expansion Connectors
The PICtail interface enables the Explorer 8 Development Board to be connected
directly to available PICtail daughter board cards. The following female headers are
available to support different PIC microcontroller connections to PICtail daughter cards
and for user access to MCU pins:
•
•
•
•
2x14 Socket (J3) – to support 8/14/18/20/28-pin devices
2x6 Socket (J11) – to support up to 44-pin devices
2x10 Socket (J5) – to support up to 68-pin devices
2x8 Socket (J28) – to support up to 80-pin devices
The PICtail Plus connectors (J19) are the card-edge modular connector found on the
right part of the board. It is based on a 120-pin connection divided into three sections
of 30 pins, 30 pins and 56 pins. Each 30-pin section provides connections to all of the
serial communication peripherals, as well as many I/O ports, external interrupts and
ADC channels. This provides enough signals to develop many different expansion
interfaces for different PICtail daughter cards.
For available PICtail daughter cards, visit the Microchip website at
www.microchip.com.
A.1.11
mikroBUS™ Connectors
Two MikroElektronika Click boards may be loaded into the sockets J32 or J35. Various
communication ports and interfaces are controlled by Jumpers J41 through J50. Power
and ground for the Click boards is supplied through the existing connections to the
sockets.
Note:
A.1.12
Sample jumper configurations are provided in Table 1-1.
Pmod™ Connectors
Two Digilent Pmod interfaces are available on the bottom middle of the Explorer 8
Development Board. Both sockets are the 12-pin version of the Digilent Pmod and
provide eight I/O signal pins, two power pins and two ground pins. The signals are
arranged so that they provide two of the 6-pin interfaces stacked.
Note:
A.1.13
Sample jumper configurations are provided in Table 1-1.
Configurable In-line Connector
A 20-pin single in-line socket (J33) is provided for connection with expansion boards.
The socket is connected in parallel to the first line of a 2x20 female header (J25)
making it a configurable in-line connector. The second line of J25 has each of its pin
socket connected to the 3.3V supply while another 2x20 female header (J39) makes
each of its pin socket available with 5V.
A.1.14
LCD
An LCD with two lines, 16 characters each, is connected to the SPI I/O expander,
MCP23S17. The two control lines and eight data lines are connected to the I/O
expander. The I/O expander has an SPI interface that connects it to the microcontroller.
The LCD is disabled or enabled through jumper J61.
 2015-2016 Microchip Technology Inc.
DS40001812B-page 35
Explorer 8 Development Board User’s Guide
A.1.15
Sample Devices
A sample part programmed with a simple program is included in the Explorer 8
Development Board Kit. The device’s I/O features and port connections are listed in
Table A-1.
TABLE A-1:
Device
PIC16F1719
DS40001812B-page 36
SAMPLE DEVICE I/O FEATURES AND CONNECTIONS
LEDs
RB3:RB0
RD3:RD0
USB
S1
S2
RC6
RB0
RA5
S3
LCD
MCLR RC3
RC5
RA2
RB5
POT
R25
RA0
ICD/
PICkit™
RB7
RB6
Y1
RA7
RA6
 2015-2016 Microchip Technology Inc.
A.2
BOARD LAYOUT AND SCHEMATICS
FIGURE A-1:
EXPLORER 8 DEVELOPMENT BOARD
3
2
4
1
3
1
1
6
1
1
6
2
1
5
2
1
5
3
1
4
3
1
4
4
1
3
4
1
3
3
2
1
2
2
1
1
1
1
1
3
2
2
2
1
5
1
2
5
1
2
6
1
1
6
1
1
7
1
0
7
1
0
2
3
2
1
1
2
2
1
1
2
2
4
1
3
8
1
4
1
3
1
2
1
1
1
0
9
8
7
1
2
2
1
1
2
2
1
3
4
1
2
2
1
6
5
4
3
2
1
1
6
1
9
8
9
5
0
0
3
4
0
2
8
1
7
1
9
6
1
1
1
0
5
0
2
1
1
1
2
4
2
3
1
2
2
3
3
3
3
2
2
2
4
1
1
3
1
4
2
0
3
3
2
2
5
1
1
1
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
3
3
3
2
2
2
1
2
0
0
1
2
0
1
2
8
2
2
7
2
1
1
2
1
1
1
2
3
2
6
2
5
2
4
1
4
4
2
2
2
2
1
1
1
1
2
2
1
1
2
2
1
1
1
1
1
1
5
1
6
3
3
1
6
2
3
2
2
2
1
1
4
3
6
5
1
8
7
8
9
1
2
2
0
1
0
1
9
1
1
1
8
1
0
1
2
1
4
1
6
1
8
2
0
2
2
2
4
2
6
2
8
3
0
3
4
3
6
3
8
4
0
4
2
4
4
4
6
4
8
5
0
5
2
5
4
5
6
5
8
6
0
6
2
6
6
6
8
7
0
7
2
7
4
7
6
7
8
8
0
8
2
8
4
8
6
2
1
1
1
2
1
7
1
3
1
6
1
4
1
5
2
4
0
1
2
1
2
2
3
9
2
1
2
1
3
2
1
2
2
1
4
2
1
3
3
3
2
2
1
2
1
3
1
8
4
3
1
1
3
2
1
1
2
4
1
2
8
3
7
3
2
1
6
2
5
1
2
1
2
1
8
4
8
3
8
2
8
1
8
0
7
9
7
8
7
7
7
6
7
5
7
4
7
3
7
2
7
1
7
0
6
9
6
8
6
7
6
6
6
5
6
4
5
2
2
7
3
6
8
4
1
1
7
3
2
2
1
1
6
3
1
2
1
2
1
1
2
6
3
2
6
3
5
1
2
6
2
3
6
1
4
6
0
6
0
9
5
1
2
2
1
1
1
7
4
2
5
3
4
1
2
0
1
8
2
1
1
7
2
2
3
5
5
9
6
5
8
3
2
2
8
5
2
4
3
3
2
1
9
1
1
0
4
1
3
9
1
7
5
7
4
3
3
9
6
2
3
3
2
3
1
8
1
6
1
5
2
1
8
5
6
9
5
5
1
2
1
1
2
2
5
1
1
0
7
2
2
3
1
4
1
7
2
1
1
1
2
1
2
0
1
1
1
2
5
4
5
3
5
2
1
4
1
8
1
7
3
6
1
1
8
2
1
3
0
5
1
6
2
2
1
1
0
1
9
2
1
1
2
1
6
1
5
1
2
1
3
5
1
1
4
5
0
1
5
4
9
2
2
1
1
2
9
2
0
2
9
6
1
5
2
2
2
1
1
1
1
8
1
7
2
2
1
3
1
0
1
9
2
8
7
1
4
2
4
2
3
1
1
6
4
8
1
7
4
7
1
8
4
6
2
0
1
9
3
1
2
2
1
1
4
1
1
1
8
2
7
8
1
3
2
6
2
5
3
2
1
4
1
9
2
0
4
5
4
4
1
2
1
5
1
2
1
7
2
6
9
1
1
2
1
2
8
2
7
5
2
2
1
1
2
3
8
8
2
6
2
1
4
3
4
3
1
1
6
1
3
1
6
2
5
1
0
1
1
9
0
9
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
2
2
2
6
1
5
9
4
3
1
7
1
4
1
5
2
4
3
1
2
9
6
1
1
9
4
8
1
8
3
7
2
1
2
8
2
3
1
1
0
0
1
0
2
3
2
2
6
1
1
9
2
0
5
9
1
0
4
1
0
6
2
1
1
1
2
2
8
1
2
2
1
0
2
1
1
0
8
1
1
0
7
1
1
2
2
1
2
1
1
1
2
1
1
4
1
2
1
1
2
1
2
1
1
4
1
3
9
1
6
1
5
2
1
2
0
1
2
1
1
6
1
1
8
1
2
0
1
3
1
1
2
1
1
3
2
1
2
1
1
2
2
1
3
2
1
2
1
1
2
3
2
2
1
4
0
3
8
3
6
3
4
3
2
3
0
2
8
2
6
2
4
2
2
2
0
1
8
1
6
1
4
1
2
1
0
8
6
4
2
1
1
3
9
3
7
3
5
3
3
3
1
2
9
2
7
2
5
2
3
2
1
1
9
1
7
1
5
1
3
1
1
4
0
3
8
3
6
3
4
3
2
3
0
2
8
2
6
2
4
2
2
2
0
1
8
1
6
1
4
1
2
3
9
3
7
3
5
3
3
3
1
2
9
2
7
2
5
2
3
2
1
1
9
1
7
1
5
1
3
1
1
2
0
1
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
9
7
5
3
1
8
6
4
2
7
5
3
1
4
3
2
1
3
1
1
2
2
3
3
1
0
1
2
1
1
 2015-2016 Microchip Technology Inc.
2
1
1
0
9
8
7
6
5
4
3
2
1
1
2
1
1
1
0
9
8
6
4
2
7
5
3
1
9
8
7
6
9
5
DS40001812B-page 37
EXPLORER 8 DEVELOPMENT SCHEMATIC - 1
RA5
RA4
RA3
RC5
RC4
RC3
RA0
RA1
RA2
RC0
RC1
RC2
Shunt 2.54mm 1x2 Handle
1
3
2
@J2_1_2
J2
BAT54SLT1
1
+9V
VIN VOUT
GND
C5
C4
C2
0.01uF
50V
0603
10uF
16V
0805
0.22uF
3
TP LOOP Red
Shunt 2.54mm 1x2 Handle
TP1
MCP1826S/3.3V
+5V
1k
D3
R7
BLUE
1k
D4
R8
BLUE
1
1k
C3
C19
C26
0.1uF
25V
0603
0.01uF
50V
0603
10uF
16V
0805
R36
470R
0805
5%
2
@J7
+3.3V
1 2
VIN VOUT
GND
0.1uF
25V
0603
3
1uF
16V
0603
Shunt 2.54mm 1x2 Handle
TP4
+3.3V
D5
R9
R37
BLUE
1k
270R
0805
5%
D6
R10
BLUE
1k
D7
R11
BLUE
1k
D8
R12
BLUE
1k
RB0
TP2
LD1
RED
J7
+3.3V
HDR-2.54 Male 1x2
C9
RD3
TP6
J24
U1
+5V
+5V
J11
12 10 8 6 4 2
11 9 7 5 3 1
TP LOOP Red
C43
2
R6
BLUE
RD2
@J24
Vusb5
1
2
3
U5
RSX101MM-30TR D12
J1
1
3
2
POWER 2.5mm
RD0
RD2
RD4
RD6
RE0
V_VAR
1k
D2
1 2
D11
LM340S-5.0/NOPB
RD1
RD3
RD5
RD7
RE1
R5
BLUE
RD1
HDR-2.54 Male 1x3
HDR-2.54 Female 2x14
RD1
RD3
RD5
RD7
RE1
D1
RD0
TM
RA5
RA4
RA3
RC5
RC4
RC3
RA0
RA1
RA2
RC0
RC1
RC2
V_VAR
PIC tail
RE2
RE3
RA7
RA6
RC7
RC6
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
28 26 24 22 20 18 16 14 12 10 8 6 4 2
27 25 23 21 19 17 15 13 11 9 7 5 3 1
8 - 14 - 18 - 20 - 28 pins
40 - 44 pins
64 - 68 pins
80 - 84 pins
J3
RE2
RE3
RA7
RA6
RC7
RC6
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
TP LOOP Black TH
RD0
RD2
RD4
RD6
RE0
RB1
LD2
YELLOW
RB2
RB3
J21
1 2
HDR-2.54 Female 2x6
MICROSMD050F-2
F1
TP8
Vusb5
VBUS
TP7
J6
2
4
1
3
+5V
+3.3V
V_VAR
4.7uF
25V
AL-A
C27
C28
1000pF
50V
0603
0.1uF
25V
0603
V_VAR
3
C17
R25A
2
TP LOOP Red
+9V
D10
D9
GREEN
1
RG0
RG2
RG4
RF0
RF2
RF4
RF6
RE4
RE6
HDR-2.54 Female 2x2
POT
SGND
V_VAR
HDR-2.54 Female 2x10
1
RJ1
RJ3
RJ5
RJ7
RH1
RH3
RH5
RH7
RJ0
RJ2
RJ4
RJ6
RH0
RH2
RH4
RH6
+5V
+3.3V
RJ0
RJ2
RJ4
RJ6
RH0
RH2
RH4
RH6
R26
RA0
C24
1000pF
50V
0603
HDR-2.54 Female 2x3
J28
RJ1
RJ3
RJ5
RJ7
RH1
RH3
RH5
RH7
16 14 12 10 8 6 4 2
15 13 11 9 7 5 3 1
 2015-2016 Microchip Technology Inc.
+9V
10K
1k
1k
1
3
5
R25
2
R13
J9
2
4
6
10k
91A
20%
Power Indicator
3
TP LOOP Black TH
RG0
RG2
RG4
RF0
RF2
RF4
RF6
RE4
RE6
V_VAR
SMBJP6KE6.8
RG1
RG3
MCLR
RF1
RF3
RF5
RF7
RE5
RE7
20 18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
J5
RG1
RG3
RG5
RF1
RF3
RF5
RF7
RE5
RE7
V_VAR
V_VAR
R14
10k
R27
10k
HDR-2.54 Female 2x8
1 S1
4
2
3
TACT SPST
R15
RB0
1k
1 S2
4
2
3
TACT SPST
R28
RA5
1k
Explorer 8 Development Board User’s Guide
DS40001812B-page 38
FIGURE A-2:
EXPLORER 8 DEVELOPMENT SCHEMATIC - 2
J29
J50
RC3
HDR-2.54 Male 1x6
C15
8MHz
RA6
@J37
Shunt 2.54mm 1x2 Handle
22pF
50V
0603
U2 LM317KTTR
MCLR
C30
VIN VOUT
ADJ
2
D13
3
1
BAT54SLT1 J30 J14
1
3
+9V
R23
1
DS40001812B-page 39
0.1uF
25V
0603
R19
C31
330R
1uF
16V
0603
ADJ
R20
1k
C7
0.1uF
25V
0603
@J14_1_2
Shunt 2.54mm 1x2 Handle
+5V
1
2
3
TP5
V_VAR
+3.3V
RJ0
RD7
RD6
RD5
RD4
RD3
RD2
RJ1
64
61
65
62
66
67
64
68
65
69
66
70
67
RD1
72
73
71
68
69
63
40
42
39
41
38
40
30
29
30
28
29
27
28
26
27
25
C16
10k
74
41
RJ5
1
2
3
70
71
RE7
RD0
RE6
20
RJ4
J37
RA5
NC
75
76
72
77
RE5
42
RA0
Y1
RA4
R18
0.1uF
25V
0603
78
19
2
C18
RE4
43
RA1
1
2
3
22pF
50V
0603
100R
79
18
RA2
J36
RA7
Shunt 2.54mm 1x2 Handle
V_VAR
TACT SPST
RE3
44
RA3
@J36
Switch
80
17
R21
C25
S3
RE2
45
10M
0.1uF
25V
0603
81
16
DNP
Shunt 2.54mm 1x2 Handle
HDR-2.54 Male 1x3
MCLR
V_VAR
PGD
PGC
46
26
1
2
3
4
5
6
47
15
V_VAR
J12
21
RH6
14
24
RA1
@J52_1_2
1
2
3
48
25
C6
0.1uF
25V
0603
20
RH7
13
RF0
MODULAR RJ25
19
RF2
Shunt 2.54mm 1x2 Handle
HDR-2.54 Male 1x3
J52
RB6
RF3
1
2
3
49
21
PGD
PGC
@J51_1_2
18
12
22
RA0
17
RF4
50
RH5
6 5 4 3 2 1
J51
16
RF5
DNP
RB7
15
RF6
J32
MCLR
V_VAR
14
RF7
NC
11
RC7
RB7
HDR-2.54 Male 1x1
HDR-2.54 Male 1x3
mikroBUS
13
V_VAR
J34
NC
37
RG1
1
2
3
12
39
RC6
11
RB5
HDR-2.54 Male 1x1
51
RC6
J44
+5V
J27
10
36
RC3
RC4
+5V
1
2
3
52
38
RC7
RG2
9
RC0
RB0
10
RG4
53
35
J43
8
37
1k
54
RC1
RC0 R30
1
16
15
14
13
12
11
10
9
7
HDR-2.54 Male 1x3
+3.3V
PWM
INT
RX
TX
SCL
SDA
+5V
GND
55
23
RC5
RD4
+3.3V
HDR-2.54 Male 1x3
AN
RST
CS
SCK
MISO
MOSI
+3.3V
GND
6
24
J45
1
2
3
4
5
6
7
8
1
RE0
RD7
RE2
56
34
HDR-2.54 Male 1x3
RC4
J26
9
MCLR
RD5
HDR-2.54 Male 1x3
1
2
3
8
RG3
57
5
36
RC3
RD6
HDR-2.54 Male 1x3
1
2
3
7
RG2
4
RA4
J47
58
33
6
RG1
3
35
5
59
RA5
4
RE0
RG0
60
2
32
3
RE1
TMS-121-01-G-S
1
31
2
RH3
34
1
RH2
HDR-2.54 Male 1x3
J46
RH0
U1A
J35
1
2
3
73
0.1uF
25V
0603
74
C14
0.1uF
25V
0603
75
C13
0.1uF
25V
0603
82
RH1
C37
0.1uF
25V
0603
33
SGND
mikroBUS
C36
0.1uF
25V
0603
V_VAR
RC4
SGND
C35
1
2
3
NC
RC6
32
+5V
V_VAR
J42
76
RC3
RC4
+5V
1
2
3
77
RC5
78
RC7
84
J41
RB1
RF1
RC7
+3.3V
HDR-2.54 Male 1x3
1k
RC1 R29
HDR-2.54 Male 1x1
RC5
16
15
14
13
12
11
10
9
80
1
2
3
PWM
INT
RX
TX
SCL
SDA
+5V
GND
22
J48
AN
RST
CS
SCK
MISO
MOSI
+3.3V
GND
23
1
RA1
2
RB7
3
RA4
4
5
6
7
+3.3V
8
83
HDR-2.54 Male 1x3
RC4
RB4
HDR-2.54 Male 1x3
79
J49
V_VAR
HDR-1.27 Male 1x3
RB6
HDR-2.54 Male 1x3
1
2
3
1
2
3
31
1
2
3
ADJ
V_VAR
RH4
 2015-2016 Microchip Technology Inc.
FIGURE A-3:
63
62
61
60
59
58
57
56
55
RJ2
RJ3
RB0
RB1
RB2
RB3
RB4
RB5
RB6
54
53
52
51
50
49
48
47
46
45
44
43
RA6
RA7
V_VAR
RB7
RC5
RC4
RC3
RC2
RJ7
RJ6
EXPLORER 8 DEVELOPMENT SCHEMATIC - 3
@J61
V_VAR
+5V
MCP2221
+3.3V
R1
10k
1
2
3
4
5
6
7
V_VAR
UART_RX
UART_TX
J18
USB_P
USB_N
2.2k
1
3
HDR-2.54 Male 2x2
C1
1
2
3
1
2
3
RC7
RC4
RC6
USB Micro B TH/SMT
HDR-2.54 Male 1x1
RB5
J61
10k
0603
1%
HDR-2.54 Male 1x3
2
4
J57
RC3
HDR-2.54 Male 2x2
R17
1
2
3
1
2
3
RB6
RC4
2
4
RB4
1.3k
0603
LCD1
6
E
5
R/W
4
RS
3
VEE
2
R24
J23
1
3
Shunt 2.54mm 1x2 Handle
2
R31
10k
0603
1%
C38
E
R/W
RS
Vo
VDD
1
0.1uF
25V
0603
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
VSS
7
8
9
10
11
12
13
14
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
LCM-S01602DTR/M
HDR-2.54 Male 1x3
@J53_2_3
@J59
Shunt 2.54mm 1x2 Handle
Shunt 2.54mm 1x2 Handle
J58
1
RC5
J55
J56
HDR-2.54 Male 1x1
RB7
1
J53
VBUS
USB_N
USB_P
0
1
2
3
4
5
J22
6.3V
0.47uF
R16
2.2k
U3
HDR-2.54 Male 1x3
VBUS
DD+
ID
GND
14
13
12
11
10
9
8
VDD
VSS
GP0
D+
GP1
DRST
VUSB
UART RX SCL
UART TX SDA
GP2
GP3
R2
1
V_VAR
RC3
@J54_2_3
R32 RC5
HDR-2.54 Male 1x3
J54
Shunt 2.54mm 1x2 Handle
RA2
R33
RB5
1
@J60
2
J60
1
2
J59
10k
0603
1%
10k
0603
1%
V_VAR
Shunt 2.54mm 1x2 Handle
C39
0.1uF
25V
0603
LCD
U4
12
13
14
11
17
16
15
18
20
19
9
10
SCK
SI
SO
CS
A2
A1
A0
RESET
INTA
INTB
VDD
VSS
GPA0
GPA1
GPA2
GPA3
GPA4
GPA5
GPA6
GPA7
GPB0
GPB1
GPB2
GPB3
GPB4
GPB5
GPB6
GPB7
21
22
23
24
25
26
27
28
1
2
3
4
5
6
7
8
E
RS
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
MCP23S17
HDR-2.54 Female 2x6 RA
RA4
RA4/VCAP
3
2
1
J4
RA5
RA5/VCAP
HDR-2.54 Male 1x3
C34
10uF
16V
0805
3
2
1
C33
0.1uF
25V
0603
0.1uF
25V
0603
+3.3V
J8
J13
 2015-2016 Microchip Technology Inc.
C21
C22
C23
0.1uF
25V
0603
0.1uF
25V
0603
0.1uF
25V
0603
0.1uF
25V
0603
J10
V_VAR
RA5/VCAP
RA4/VCAP
MCLR
RC5
RC4
RC3
RC6
RC7
RB7
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
110-91-320-41-001
RA0
RA1
RA2
RC0
RC1
RC2
RB5
RB4
RB6
MCLR
RA0
RA1
RA2
RA3
RA4/VCAP
RA5/VCAP
RA7
RA6
RC0
RC1
RC2
RC3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
110-91-328-41-001
J20
RC2
RC5
RC4
RC3
+5V
HDR-2.54 Male 1x3
C32
V_VAR
C20
HDR-2.54 Female 2x6 RA
RD4
RD5
RD6
RD7
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
V_VAR
RC7
RC6
RC5
RC4
MCLR
RA0
RA1
RA2
RA3
RA4/VCAP
RA5/VCAP
RE0
RE1
RE2
V_VAR
RA7
RA6
RC0
RC1
RC2
RC3
RD0
RD1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
HDR-2.54 Male 1x3
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
110-87-640-41-001151
J15
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
V_VAR
RD7
RD6
RD5
RD4
RC7
RC6
RC5
RC4
RD3
RD2
J16 +5V
1
2
3
+3.3V
HDR-2.54 Male 1x3
11 9 7 5 3 1
12 10 8 6 4 2
J31
11 9 7 5 3 1
12 10 8 6 4 2
J17
RC0
RC1
RC7
RC6
RD0
RD1
RD2
RD3
Explorer 8 Development Board User’s Guide
DS40001812B-page 40
FIGURE A-4:
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Austin, TX
Tel: 512-257-3370
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Dongguan
Tel: 86-769-8702-9880
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
India - Pune
Tel: 91-20-3019-1500
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-213-7828
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Venice
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Poland - Warsaw
Tel: 48-22-3325737
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
07/14/15
 2015-2016 Microchip Technology Inc.
DS40001812B-page 41