For more information, please visit the product page. rev. page 1 of 3 date 08/2008 DESCRIPTION: incremental shaft type encoder PART NUMBER: NSC-S ELECTRICAL SPECIFICATIONS output waveform output signals current consumption square wave A, B, Z phase, inverse A, B, Z phase ≤80 mA (voltage output), ≤60 mA (open collector output, open collector HV output), ≤150 mA (line driver output) 150 kHz 5 V dc ± 10%, 12 V dc ± 10% (voltage output, open collector output), 12 V dc ± 10% (open collector HV output), 5 V dc ± 10% (line driver output) ≤80 mA (voltage output), ≤60 mA (open collector output, open collector HV output), ≤150 mA (line driver output) 20 mA max. Vcc - 1 V (voltage output), ≥2.5 V (line driver output) ≤0.5 V 36, 50, 60, 100, 150, 200, 250, 300, 360, 400, 500, 512, 600, 800, 1000, 1024, 1500* ≤1 μs, ≤200 ns (line driver output only) output current sink current output voltage “H” “L” output resolution (ppr) waveform rise/fall time *24 V dc not available MECHANICAL SPECIFICATIONS nt 1.0 kgf 0.5 kgf 10 gf·cm max. 1x105 rad/s2 2.0 g·cm2 6000 RPM 50 G, 11 ms, 3 times each on XYZ 10 ~ 50 Hz, double amplitude 1.5 mm, 2 hours 1x108 rpm·hrs co max shaft load, radial: axial: starting torque angular acceleration moment of inertia max rotational speed shock resistance vibration proof rotational life in u ed frequency response supply voltage ENVIRONMENTAL SPECIFICATIONS D is operating temp storage temp humidity -10° to +70° C -30° to +80° C RH 85% max., non-collecting ELECTRICAL CONNECTIONS 2M Color of Lead Wire 2MC 2MHC Red Black Green or Blue White Yellow Shielding Braid Description Power Source 0V Common Signal A Signal B Signal Z NC 2MD Color of Lead Wire Red Black Green Blue Shielding Braid Description Power Source 0V Common Signal A Signal A NC Color of Lead Wire White Gray Yellow Orange 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 Description Signal B Signal B Signal Z Signal Z For more information, please visit the product page. rev. page 2 of 3 date 08/2008 DESCRIPTION: incremental shaft type encoder PART NUMBER: NSC-S ORDERING INSTRUCTIONS ed NSC-XXXX-2MX-XX-XXX-S Resolution (PPR) 0036 = 36 PPR 04 = 400 PPR 005 = 50 PPR 05 = 500 PPR 006 = 60 PPR 0512 = 512 PPR 01 = 100 PPR 06 = 600 PPR 015 = 150 PPR 08 = 800 PPR 02 = 200 PPR 10 = 1000 PPR 025 = 250 PPR 1024 = 1024 PPR 03 = 300 PPR 15 = 1500 PPR 036 = 360 PPR 2M Vcc 2kΩ Input voltage: 05 = 5 V dc 12 = 12 V dc 24 = 24 V dc* in u nt CIRCUIT CONNECTIONS Output type: "no entry" = Voltage output C = Open collector output HC = Open collector HV output D = Line driver output Shaft diameter: 05 = ø5 mm 125= ø0.125 “ 2MC 2MHC 2MD Vcc Reverse Signal 0V 0V is 0V D OUTPUT WAVEFORM CW Rotating Toward Clockwise Viewed from an Arrow Rising point of A-Signal is always at one point while Z-Signal is at H-Level in CW. P Signal A P= a b c Sig A 1 PPR Sig A d Signal B a, b, c, d = h P P ± 4 8 P < 3P = h < = 2 2 Sig B Sig B Sig Z Signal Z hmin hmax Vcc Signal Signal co Signal *HC type only Wave Ratio (Duty); 50 ± 25 (%) Sig Z 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 PC FILE NAME: NSC-S COPYRIGHT 2008 BY CUI INC. 22.0 0.866 scale 1:1 500.0 n o c s i D Z Signal Position Mark 5.0 0.197 27.0 1.063 28.0 1.102 30.0 1.181 JMS DRAWN BY: NSC-S APPROVED BY: Incremental Encoder PART NO. TITLE: DATE 8/20/2008 UNITS: A 2:1 SCALE: MM [INCHES] REV: RoHS 8.0 0.315 24.8 0.976 4.5 0.177 20050 SW 112th Ave. Tualatin, OR 97062 Phone: 503-612-2300 800-275-4899 Fax: 503-612-2383 Website: www.cui.com TOLERANCE: ±0.3mm UNLESS OTHERWISE SPECIFIED 2.3 0.091 12.0 0.472 d e DESCRIPTION NEW DRAWING 1.3 0.051 u n it REV. A For more information, please visit the product page.