Document 1069-1 Chip Inductors – 0402DF (1005) • Higher inductance values than other 0402 inductors • Ferrite construction for high current handling • 25 inductance values from 20 nH to 3.3 µH • Ideal for use in both mobile and infrastructure equipment • Equally effective on-board or modular Part number1 Inductance2 ±5% (nH) 0402DF-200XJR_ 20 0402DF-360XJR_ 36 0402DF-560XJR_ 56 0402DF-770XJR_ 77 0402DF-900XJR_ 90 0402DF-101XJR_ 105 0402DF-121XJR_ 120 0402DF-141XJR_ 140 0402DF-151XJR_ 150 0402DF-181XJR_ 180 0402DF-221XJR_ 220 0402DF-271XJR_ 270 0402DF-301XJR_ 300 0402DF-331XJR_ 330 0402DF-361XJR_ 360 0402DF-421XJR_ 420 0402DF-471XJR_ 470 0402DF-531XJR_ 530 0402DF-591XJR_ 590 0402DF-701XJR_ 700 0402DF-771XJR_ 770 0402DF-901XJR_ 900 0402DF-102XJR_1000 0402DF-222XJR_2200 0402DF-332XJR_3300 • Developed for use in cellular applications: As a filter element in bandstop and low pass filters As a one pole filter or RF choke in cellular bands • Can also be used for ground-to-ground isolation Impedance typ (Ohms) 900 MHz 1.7 GHz 90150 150250 250480 350580 400600 5301000 515900 6501075 7001170 8501460 11002050 13002150 17252630 21002750 21503100 21753350 25503670 39503050 47703090 57501830 49001800 71304470 280180 200120 160 80 1. When ordering, please specify termination and packaging codes: 0402DF-771XJRW Termination:R=RoHS compliant matte tin over nickel over silverplatinum-glass frit. Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging:W =7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). U=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance measured at 7.9 MHz using a Coilcraft SMD-F test fixture and Coilcraft-provided correlation pieces with an Agilent/HP 4286 impedance analyzer. 3. SRF measured using Agilent/HP 8753D network analyzer and Coilcraft SMD‑D test fixture. 4. DCR measured on Cambridge Technology micro-ohmmeter and a Coilcraft CCF858 test fixture. 5. Current that causes a 15°C temperature rise from 25°C ambient. Because of their open construction, these parts will not saturate. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. SRF typ3 (MHz) 2950 2400 2200 2050 2300 1660 2000 1450 1800 1680 1560 1480 1400 1340 1200 1100 1070 1000 960 600 585 760 235 125 80 DCR max4 (Ohms) 0.049 0.055 0.061 0.072 0.079 0.104 0.090 0.141 0.130 0.172 0.240 0.265 0.340 0.435 0.475 0.510 0.670 0.715 0.780 1.30 1.35 1.50 1.05 1.80 2.20 Irms5 (mA) 1400 1300 1200 1100 1000 850 950 750 830 730 600 590 490 430 420 400 340 330 320 230 220 230 190 170 150 Core material Ferrite Environmental RoHS compliant without exemption, halogen free Terminations RoHS compliant matte tin over nickel over silver-platinumglass frit. Weight 0.9 – 1.1 mg Ambient temperature –40°C to +85°C with Irms current Maximum part temperature +100°C (Ambient + temperature rise) Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +150 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000 per 7″ reel. Paper tape: 8 mm wide, 0.68 mm thick, 2 mm pocket spacing PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Specifications subject to change without notice. Please check our website for latest information. Document 1069-1 07/29/15 Document 1069-2 Chip Inductors – 0402DF Series Typical Z vs Frequency Typical L vs Frequency 1000 10000 900 nH 770 nH 590 nH 220 nH 100 150 nH 77 nH 1000 530 nH 420 nH 330 nH 160 nH 150 nH 120 nH 77 nH Impedance (Ohms) Inductance (nH) 530 nH 330 nH 770 nH 20 nH 100 10 1 20 nH 10 1 100 10 1000 0.1 10000 1 10 Frequency (MHz) 100 10000 C E 1000 F A G E D terminal F Terminal wraparound: approx 0.007/0,18 both ends A max B max C max D E F Recommended Land Pattern G H 0.044 0.024 0.026 0.018 0.008 0.014 0.025 0.026 inches 1,11 0,61 0,65 0,46 0,20 900 nH H Pick and place material Impedance (Ohms) B overall 1000 10000 Frequency (MHz) 590 nH 420 nH 220 nH 160 nH 120 nH 100 10 1 0,36 0,635 0,66 mm 0.1 1 10 100 1000 10000 Frequency (MHz) Document 1069-2 Revised 07/29/15