0603HL

Document 894-1
Chip Inductors – 0603HL Series (1608)
•Higher inductance values than other 0603 inductors
•Inductance range: 330 nH – 3.3 µH
Part number1
Q typ3
Inductance2
±5% (nH)
0603HL-331XJR_ 330 @ 25 MHz
0603HL-391XJR_ 390 @ 25 MHz
0603HL-471XJR_ 470 @ 25 MHz
0603HL-511XJR_ 510 @ 25 MHz
0603HL-561XJR_ 560 @ 25 MHz
0603HL-681XJR_ 680 @ 25 MHz
0603HL-821XJR_ 820 @ 25 MHz
0603HL-102XJR_
1000 @ 25 MHz
0603HL-122XJR_
1200 @ 25 MHz
0603HL-152XJR_
1500 @ 25 MHz
0603HL-182XJR_
1800 @ 25 MHz
0603HL-222XJR_
2200 @ 25 MHz
0603HL-272XJR_
2700 @ 25 MHz
0603HL-332XJR_
3300 @ 25 MHz
13 @ 25 MHz
13 @ 25 MHz
12 @ 25 MHz
12 @ 25 MHz
12 @ 25 MHz
12 @ 25 MHz
14 @ 25 MHz
14 @ 25 MHz
14 @ 25 MHz
15 @ 25 MHz
16 @ 25 MHz
16 @ 25 MHz
16 @ 25 MHz
18 @ 25 MHz
1. When ordering, please specify termination and packaging code:
0603HL-332XJRC
Termination:R=RoHS compliant matte tin over nickel over silver-
platinum-glass frit
Special order: Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
2. Inductance measured at 0.1 Vrms, using a Coilcraft SMD-A fixture in
Agilent/HP 4287A impedance analyzer or equivalent with Coilcraftprovided correlation pieces.
3. Q measured using a Coilcraft SMD-A fixture in Agilent/HP 4287A
impedance analyzer or equivalent.
4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft
SMD‑D test fixture.
5. DCR measured on Cambridge Technology Micro-ohmmeter or
equivalent.
6. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
SRF typ4 DCR max5
Irms6Color
(MHz) (Ohms)(mA)code
420
400
200
340
330
310
290
250
230
190
180
165
150
135
0.970
1.05
1.15
1.20
1.35
1.80
2.45
2.80
3.20
4.10
5.30
5.90
7.00
9.10
330
330
300
300
300
260
190
190
180
150
140
130
120
110
Violet
Gray
White
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Gray
White
Black
Designer’s Kit C449 contains 10 of each value
Core material Ceramic
Environmental RoHS compliant without exemption, halogen free
Terminations RoHS compliant matte tin over nickel over silver-platinum-glass frit. Other terminations available at additional cost.
Weight 3.2 – 4.4 mg
Ambient temperature –40°C to +125°C with Irms current
Maximum part temperature +140°C (ambient + temp rise).
Storage temperature Component: –40°C to +140°C.
Tape & reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +50 to +150 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000 per 7″ reel. Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.0 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 894-1 Revised 10/12/15
Document 894-2
Chip Inductors – 0603HL Series
Typical L vs Frequency
Typical Q vs Frequency
25
10,000
20
Inductance (nH)
3300 nH
Q Factor
1800 nH
1000 nH
1000
560 nH
15
560 nH
10
390 nH
390 nH
1000 nH
5
1800 nH
3300 nH
100
1
100
10
0
1000
Frequency (MHz)
Typical Impedance vs Frequency
1
Impedance (kOhms)
1800 nH
1000 nH 560 nH
3300 nH
390 nH
A
10
E
terminal
1
1000
Frequency (MHz)
B
overall
100
100
10
C
H
D
F
I
G
J
F
I
Terminal wraparound:
approx 0.01/0,25 both ends
Recommended
Land Pattern
ABC
maxmaxmax D E F G H I
J
0.0710.047 0.037 0.010 0.0300.0110.038 0.0400.0250.025inches
1,80 1,19 0,94 0,25 0,760,280,97 1,020,640,64
mm
0.1
Note: Height dimension (C) is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
0.01
10
100
1000
Frequency (MHz)
Document 894-2 Revised 10/12/15