LPZxxx

Document 1244-1
Shielded Power Inductors High Inductance
• High inductance values (220 – 4700 µH) not available in the
corresponding LPS series of parts
• Rugged construction improves pick and place operation
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
Part number1
Inductance2
±20% (µH)
DCR
max3
(Ohms)
Isat (A)5
Irms (A)6
typ4
(MHz)
10% drop 20% drop 30% drop 20°C rise 40°C rise
SRF
LPZ3008-224MR_
LPZ3008-334MR_
220
330
11.5
18.0
9.0
7.0
0.0670.0730.076 0.1000.145
0.0590.0640.066 0.0900.130
LPZ3010-334MR_
330
18.5
7.0
0.10 0.105 0.115
LPZ3015-334MR_
330
23.0
5.0
0.100.110.11 0.070
0.095
0.0850.11
LPZ3314-105MR_
LPZ3314-155MR_
1000
1500
31.0
44.0
3.0
2.7
0.0900.0990.100 0.0820.100
0.0800.0860.090 0.0600.080
LPZ4012-335MR_
3300
65.0
0.95
0.0740.0780.080 0.0500.065
LPZ4018-155MR_
LPZ4018-185MR_
LPZ4018-225MR_
LPZ4018-335MR_
1500
1800
2200
3300
25.0
31.5
32.5
48.0
2.4
2.3
2.1
1.6
0.095 0.10 0.105
0.0900.0950.10
0.0880.0940.10
0.0820.0920.094
0.0800.11
0.0700.095
0.0700.090
0.0550.075
LPZ4414-155MR_
LPZ4414-185MR_
LPZ4414-225MR_
LPZ4414-335MR_
1500
1800
2200
3300
26.4
35.0
42.5
56.0
2.2
1.9
1.9
1.3
0.0960.0990.10
0.0890.0940.097
0.0820.0890.092
0.0720.0780.083
0.0850.11
0.0750.10
0.0650.080
0.0550.070
LPZ5010-105MR_
1000
28.0
3.0
0.0870.0960.10
0.0800.11
LPZ5015-335MR_
LPZ5015-475MR_
3300
4700
55.0
80.0
1.7
1.4
0.0640.0720.076 0.0550.075
0.0620.0690.072 0.0450.065
1. When ordering, please specify termination and packaging codes:
LPZ3008-334MRC
Termination:R=RoHS compliant matte tin over nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5) or
P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or equivalent.
5. DC current that causes the specified inductance drop from its value
without current.
6. Current that causes the specified temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 1244-1 Revised 01/05/15
Document 1244-2
Shielded Power Inductors – LPZ3008
L vs Current
L vs Frequency
800
700
600
600
500
500
400
Inductance (µH)
1000
800
700
Inductance (µH)
1000
330 µH
300
220 µH
200
400
330 µH
300
220 µH
200
100
100
0.0001
0.01
0.001
0.10
Current (A)
0.01
0.1
1
10
Frequency (MHz)
Current Derating
120
100
90
80
70
60
50
40
30
20
25°C
Percent of rated Current
110
Isat
Irms
10
0
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 22 – 25 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
Document 1244-2 Revised 01/05/15
Document 1244-3
Shielded Power Inductors – LPZ3010
L vs Current
L vs Frequency
800
700
800
700
600
600
500
500
400
Inductance (µH)
1000
Inductance (µH)
1000
330 µH
300
200
100
400
330 µH
300
200
100
0.0001
0.01
0.001
0.10
Current (A)
0.01
0.1
1
10
Frequency (MHz)
Typical Current Derating
120
100
90
80
70
60
50
40
30
20
25°C
Percent of rated Current
110
Isat
Irms
10
0
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 25 – 32 mg
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
Document 1244-3 Revised 01/05/15
Document 1244-4
Shielded Power Inductor – LPZ3015
L vs Current
L vs Frequency
1000
800
700
Inductance (µH)
600
500
400
330 µH
300
200
100
0.001
0.1
0.01
1.0
Current (A)
Current Derating 100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 40 – 45 mg
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
Document 1244-4 Revised 01/05/15
Document 1244-5
Shielded Power Inductors – LPZ3314
Typical L vs Current
Typical L vs Frequency
Current Derating
100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 44.1 – 46.5 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth
Recommended pick and place nozzle OD: 3.3 mm; ID: ≤ 1.65 mm
Document 1244-5 Revised 01/05/15
Document 1244-6
Shielded Power Inductors – LPZ4012
Typical L vs Current
Typical L vs Frequency
Current Derating
0.1535 ±0.003*
3,90 ±0,076
120
110
XXX X
90
80
70
Dash
number
60
50
Internal
code
30
20
Isat
Irms
-40
-20
0
20
Winding
direction
Recommended
Land Pattern
0.0433 ±0.004 *
1,10 ±0,10
40
10
0
0.1535 ±0.003*
3,90 ±0,076
0.105
2,66
0.059
1,50
25°C
Percent of rated current
100
40
60
80
100
0.110 0.045
2,79 1,15
120 140
Ambient temperature (°C)
0.0305
0,775
0.153
3,89
0.129
3,28
0.060
1,52
are of the case not including
* Dimensions
the termination. For maximum overall
dimensions including the termination, add
0.005 in / 0,13 mm.
For optional tin-lead and tin-silver-copper
terminations, dimensions are for the
mounted part. Dimensions before mounting
can be an additional 0.005 inch / 0,13 mm).
0.173
4,40
Dimensions are in
inches
mm
Weight 54 – 64 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.25 mm thick, 8 mm pocket spacing, 1.32 mm pocket depth
Recommended pick and place nozzle OD: 4 mm; ID: ≤ 2 mm
Document 1244-6 Revised 01/05/15
Document 1244-7
Shielded Power Inductors – LPZ4018
Typical L vs Current
Typical L vs Frequency
Current Derating
100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 90 – 100 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.9 mm pocket depth
Recommended pick and place nozzle OD: 4 mm; ID: ≤ 2 mm
Document 1244-7 Revised 01/05/15
Document 1244-8
Shielded Power Inductors – LPZ4414
Typical L vs Current
Typical L vs Frequency
Current Derating
0.169 ±0.004*
4,30 ±0,10
100
XXX X
90
80
70
Dash
number
60
50
30
20
10
0
0.169 ±0.004*
4,30 ±0,10
Winding
direction
Internal
code
0.0551 max
*
1,40
40
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
Recommended
Land Pattern
0.128
3,25
0.059
1,50
40
60
80
100
120 140
0.030 typ
0,75
Ambient temperature (°C)
0.185
4,70
0.118
3,00
0.030 typ
0,75
are of the case not including
* Dimensions
the termination. For maximum overall
dimensions including the termination, add
0.005 in / 0,13 mm.
For optional tin-lead and tin-silver-copper
terminations, dimensions are for the
mounted part. Dimensions before mounting
can be an additional 0.005 inch / 0,13 mm).
0.124
3,15
0.055
1,40
0.059
1,50
0.118
3,00
0.185
4,70
Dimensions are in
inches
mm
Weight 82.3 – 89.8 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth
Recommended pick and place nozzle: OD: 4.5 mm; ID: ≤ 2 mm
Document 1244-8 Revised 01/05/15
Document 1244-9
Shielded Power Inductor – LPZ5010
Typical L vs Current
Typical L vs Frequency
Current Derating
100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 70 – 75 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
Document 1244-9 Revised 01/05/15
Document 1244-10
Shielded Power Inductors – LPZ5015
Typical L vs Current
Typical L vs Frequency
Typical Current Derating
100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Dimensions are in
inches
mm
Weight 102 – 107 mg
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.57 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
Document 1244-10 Revised 01/05/15