Datasheet

SIDACtor ® Protection Thyristors
SLIC Protection
Battrax® Protection Thyristor Series Single Port Positive/Negative - MS-013
Pb e3
RoHS
Description
This series is designed specifically to protect SLIC devices
utilizing positive and negative ringing signals. This one
device will protect a single port.
Features and Benefits
ringing compatible
• Low voltage overshoot
Agency Approvals
Agency
Agency File Number
E133083
Pinout Designation
1
6
2
5
3
4
• Low on-state voltage
• Single-port protect
• Does not degrade surge
capability after multiple
surge events within
limit.
• Gate trigger tracking
device
• Fails short circuit when
surged in excess of
ratings
• Pb-free E3 means 2nd
level interconnect is
Pb-free and the terminal
finish material is tin(Sn)
(IPC/JEDEC J-STD609A.01)
• Low capacitance
• Positive and negative
• RoHS Compliant and
Lead-Free
Applicable Global Standards
Schematic Symbol
(-VREF) 2
• GR 1089 Intra-building
• TIA-968-B
• IEC 61000-4-5 2nd
edition
• ITU K.20/21 Enhanced
Level
6 (Ground)
(T) 1
• TIA-968-A
• YD/T 1082
• ITU K.20/21 Basic Level
• YD/T 993
• GR 1089 Inter-building
• YD/T 950
5 (+VREF)
Additional Information
(R) 3
4 (Ground)
Datasheet
Samples
Resources
Electrical Characteristics
Part Number
Marking
VDRM
@lDRM=5µA
VS
@100V/µs
V min
V max
IH
IS
mA min mA max
IT
VT
@IT=2.2 Amps
Capacitance*
A max
V max
pF min pF max
B3104UCLxx
B3104UC I±VREFI + I±1.2VI I±VREFI + I±10VI
100
100
2.2
4
30
200
B3164UCLxx
B3164UC I±VREFI + I±1.2VI I±VREFI + I±10VI
160
100
2.2
4
30
200
B3204UCLxx
B3204UC I±VREFI + I±1.2VI I±VREFI + I±10VI
200
100
2.2
4
30
200
Notes:
- Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted).
- Components are bi-directional
- All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 4 & 6) and
Ring (pin 3) to Ground (pin 4 & 6)
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/13/16
- VREF Max Value for the negative Battrax is -200 V.
- VREF Max Value for the positive Battrax is +110 V.
- XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack).
* Off-state capacitance (CO) is measured across pins 1 & 4,6 and 3 & 4,6
at 1 MHz with a 2V bias.
Battrax® Single Port Pos/Neg
The Single Port Positive/Negative Battrax® Protection
Thyristor Series are programmable SIDACtor® components
designed to protect SLICs (Subscriber Line Interface
Circuit) from damaging overvoltage transients.
SIDACtor ® Protection Thyristors
SLIC Protection
Surge Ratings
Series
IPP
ITSM
50/60 Hz
di/dt
A min
A min
A/µs max
200
50
500
0.2/310
0.5/700 2
2/10
2/10 2
8/20
1.2/50 2
10/160
10/160 2
10/560 1
10/560 2
5/320 1
9/720 2
10/360 1
10/360 2
10/1000 1
10/1000 2
5/310 1
10/700 2
A min
A min
A min
A min
A min
A min
A min
A min
50
500
400
200
150
200
175
100
1
C
1
1
1
Notes:
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium.
- IPP ratings applicable over temperature range of -40ºC to +85ºC (IPP rating assumes VREF equals +/- 48 V)
- The component must initially be in thermal equilibrium with -40°C < TJ < +150°C
1 Current waveform in µs
2 Voltage waveform in µs
Thermal Considerations
Package
Symbol
Modified MS-013
6
5
4
Parameter
Value
Unit
TJ
Operating Junction Temperature Range
-40 to +125
°C
TS
Storage Temperature Range
-65 to +150
°C
60
°C/W
1
R0JA
3
Thermal Resistance: Junction to Ambient
V-I Characteristics
tr x td Pulse Waveform
+I
VDRM
IH
VS
IPP
VREF
-VREF
VDRM
VT
IS
-V
IDRM
IS
IT
IPP
VS
IDRM
+V
IH
IPP – Peak Pulse Current – %IPP
2
100
Waveform = tr x td
50
Half Value
0
0
-I
Normalized VS Change vs. Junction Temperature
tr = rise time to peak value
td = decay time to half value
Peak
Value
td
tr
t – Time (µs)
Normalized DC Holding Current vs. Case Temperature
IH
8
6
25 °C
4
IH (TC = 25ºC)
10
Ratio of
Percent of VS Change – %
2.0
14
12
2
0
-4
-6
1.8
1.6
1.4
1.0
0.8
0.6
0.4
-8
-40 -20
0
20 40 60 80 100 120 140 160
Junction Temperature (TJ) – °C
25°C
1.2
-40
-20
0
20
40
60
80
100 120 140 160
Case Temperature (TC) - ºC
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/13/16
SIDACtor ® Protection Thyristors
SLIC Protection
Soldering Parameters
Pre Heat
- Temperature Max (Ts(max))
- Time (Min to Max) (ts)
Average ramp up rate (Liquidus Temp (TL)
to peak)
3°C/sec. Max.
TS(max) to TL - Ramp-up Rate
3°C/sec. Max.
Reflow
- Temperature (TL) (Liquidus)
+217°C
- Temperature (tL)
60-150 secs.
Peak Temp (TP)
+260(+0/-5)°C
Time within 5°C of actual Peak Temp (tp)
30 secs. Max.
Ramp-down Rate
6°C/sec. Max.
Time 25°C to Peak Temp (TP)
8 min. Max.
Do not exceed
+260°C
tP
Critical Zone
TL to TP
Ramp-up
TL
TS(max)
tL
Ramp-down
Preheat
TS(min)
tS
25
time to peak temperature
(t 25ºC to peak)
Time
Environmental Specifications
Physical Specifications
Lead Material
Copper Alloy
Terminal Finish
100% Matte-Tin Plated
Body Material
TP
Temperature
- Temperature Min (Ts(min))
Figure 1
UL Recognized epoxy meeting
flammability classification V-0
Battrax Series Single Port Pos-Neg MS-013 Part Numbering.eps
For pg. 135
Part Numbering
High Temp Voltage
Blocking
80% Rated VDRM (VDC Peak ) +125°C or +150°C,
504 or 1008 hrs. MIL-STD-750 (Method 1040)
JEDEC, JESD22-A-101
Temp Cycling
-65°C to +150°C, 15 min. dwell, 10 up to 100
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
Biased Temp &
Humidity
52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/
JEDEC, JESD22-A-101
High Temp Storage
+150°C 1008 hrs. MIL-STD-750 (Method 1031)
JEDEC, JESD22-A-101
Low Temp Storage
-65°C, 1008 hrs.
Thermal Shock
0°C to +100°C, 5 min. dwell, 10 sec. transfer,
10 cycles. MIL-STD-750 (Method 1056) JEDEC,
JESD22-A-106
Autoclave (Pressure
Cooker Test)
+121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/
JEDEC, JESD22-A-102
Resistance to Solder
Heat
+260°C, 30 secs. MIL-STD-750 (Method 2031)
Moisture Sensitivity
Level
85%RH, +85°C, 168 hrs., 3 reflow cycles
(+260°C Peak). JEDEC-J-STD-020, Level 1
MS-013 Part Marking Drawing_2009-03-05.eps
Part Marking
B3 xx 4 U C L xx
TYPE
B3: Dual (Positive & Negative
Battrax SIDACtor)
PACKING OPTIONS
RP: Reel Pack
TP: Tube Pack
XXXXXXX
RoHS COMPLIANT
HOLDING CURRENT
10: 100 mA
20: 200 mA
16: 160 mA
CONSTRUCTION VARIABLE
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/13/16
IPP RATING
PACKAGE TYPE
Part Marking Code
(Refer to Electrical Characteristics Table)
Date Code
XXXXX
Battrax® Single Port Pos/Neg
Pb-Free assembly
(see Fig. 1)
+150°C
+200°C
60-180 secs.
Reflow Condition
SIDACtor ® Protection Thyristors
SLIC Protection
Dimensions — MS-013
Dimensions
0.065
(1.65)
Pad Outline
C
0.460
(11.68)
0.138
(3.50)
Dimension are in inches
(and millimeters).
0.059
(1.50)
E
D
7º TYP
J
7º TYP
A
G
Burr Side
H
96º
A
Mold Split
Line
4º
A
7º TYP
BSC*
F
7º TYP
MIN Length
of Flat
K
Detail A
B
A
B
C
D
E
F
G
H
J
K
BSC*
Inches
Millimeters
Min
Max
Min
Max
0.360
0.352
0.400
0.043
0.047
0.293
0.289
0.089
0.041
0.020
0.133
0.364
0.356
0.412
0.045
0.055
0.297
0.293
0.093
0.049
9.14
8.94
10.16
1.09
1.19
7.44
7.34
2.26
1.04
0.51
3.38
9.25
9.04
10.46
1.13
1.40
7.54
7.44
2.36
1.24
0.143
3.63
* BSC = Basic Spacing between Centers
Packing Options
Package Type
U
Description
Quantity
Added Suffix
Industry Standard
Modified MS-013 6-pin
Tape and Reel Pack
1500
RP
EIA-481-D
Modified MS-013 6-pin
Tube Pack
500
(50 per tube)
TP
N/A
Tape and Reel Specification — MS-013
.157
(4.0)
.630
(16.0)
.472
(12.0)
12.99
(330)
.512 (13.0) Arbor
Hole Dia.
Dimensions are in inches
(and millimeters)
0.700
(17.8)
Direction of Feed
Tube Pack Specification — MS-013
Message Location
.045
(1.14)
.310
(7.87)
90˚
.165
(4.19)
6
Interior of the Tube
.150
(3.81)
.225
(5.72)
.525
(13.34)
.020 ± .005 WALL TYP.
(0.51 ± 0.13)
.108
(2.74)
.005 A
20.000 ± .030
(508.00 ± 0.76)
.110
(2.79)
A
Dimensions are in inches
(and millimeters)
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/13/16