S6SBP401AJ0SA1001, S6SBP401AM2SA1001 Evaluation Kit for Automotive PMIC Operation Manual Publication Number S6SBP401AJ0SA1001_SS901-00045 CONFIDENTIAL Revision 1.0 Issue Date September 11, 2015 v1.1 O P E R A T I O N M A N U A L Preface This manual explains how to use the evaluation board. Be sure to read this manual before using the product. For this product, please consult with sales representatives or support representatives. Handling and Use Handling and use of this product and notes regarding its safe use are described in the manuals. Follow the instructions in the manuals to use this product. Keep this manual at hand so that you can refer to it anytime during use of this product. Notice on this Document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. 2 CONFIDENTIAL S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N M A N U A L Caution of the Products Described in this Document The following precautions apply to the product described in this manual. WARNING Electric Shock, Damage Electric Shock, Damage Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user’s system if the product is not used correctly. Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this CAUTION product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and unplug the cables. Cuts, Damage Watch your step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. Cuts The product contains sharp edges that are left unavoidably exposed, such as jumper plugs. Handle the product with due care not to get injured with such pointed parts. Do not place anything on the product or expose the product to physical shocks. Do not carry the Damage product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Since the product contains many electronic components, keep it away from direct sunlight, high Damage temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Damage Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. To prevent electrostatic breakdown, do not let your finger or other object come into contact with Damage the metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. When turning the power on or off, follow the relevant procedure as described in this document. Damage Before turning the power on, in particular, be sure to finish making all the required connections. Furthermore, be sure to configure and use the product by following the instructions given in this document. Using the product incorrectly or inappropriately may cause a fault. Because the product has no casing, it is recommended that it be stored in the original Damage packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL 3 V1.1 O P E R A T I O N M A N U A L Table of Contents 1. Description ............................................................................................................................................... 5 2. Evaluation Board Specification .............................................................................................................. 6 3. Pin Descriptions ...................................................................................................................................... 7 3.1 Input/Output Descriptions ............................................................................................................... 7 3.2 Jumper Descriptions ....................................................................................................................... 9 4. Setup ....................................................................................................................................................... 10 4.1 Connecting ................................................................................................................................... 10 4.2 Verification .................................................................................................................................... 10 5. Layout ..................................................................................................................................................... 11 5.1 Component Layout ....................................................................................................................... 11 5.2 Wiring Layout ............................................................................................................................... 12 6. Circuit Schematic .................................................................................................................................. 13 7. Component List ..................................................................................................................................... 14 8. Ordering Information ............................................................................................................................. 16 9. Major Changes ....................................................................................................................................... 16 Figures Figure 1-1 Board Outline ............................................................................................................................ 5 Figure 2-1 Evaluation Board Specification ................................................................................................. 6 Figure 3-1 Pin Layout ................................................................................................................................. 8 Figure 4-1 Connecting the Board and Some Equipment .......................................................................... 10 Figure 5-1 Evaluation Board Component Layout ...................................................................................... 11 Figure 5-2 Evaluation Board Wiring Layout .............................................................................................. 12 Figure 6-1 Evaluation Board Circuit Schematic ........................................................................................ 13 Tables Table 3-1 Input/Output Descriptions ........................................................................................................... 7 Table 3-2 Jumper Descriptions ................................................................................................................... 9 Table 7-1 Evaluation Board Component List ............................................................................................ 14 Table 8-1 Ordering Information ................................................................................................................. 16 Table 9-1 Major Changes ......................................................................................................................... 16 4 CONFIDENTIAL S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 S6SBP401AJ0SA1001, S6SBP401AM2SA1001 Evaluation Kit for Automotive PMIC Operation Manual 1. Description S6SBP401AJ0SA1001 and S6SBP401AM2SA1001 are the evaluation kit for power block of automotive ADAS platform. These boards implement S6BP401A of power management IC. It is necessary to prepare DC power supply. Figure 1-1 Board Outline S6SBP401AJ0SA1001 S6SBP401AM2SA1001 DC Power Supply +5V 5V S6BP401A : PMIC CN_VIN DC/DC Converter DD1 EN1 VOUT1 1.250V / 2A CN_VOUT2 VOUT2 1.250V / 3A: S6SBP401AJ0SA1001 1.125V / 3A: S6SBP401AM2SA1001 DD3 CN_VOUT3 VOUT3 1.850V / 2A: S6SBP401AJ0SA1001 2.550V / 2A: S6SBP401AM2SA1001 DD4 CN_VOUT4 VOUT4 3.375V / 1A DD2 EN2 CN2 CN_VOUT1 EN3 EN4 LDO ENL1 LDO1 CN_VOUTL1 ENL2 LDO2 CN_VOUTL2 WDI WatchDog Power Good September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL VOUTL1 3.300V / 0.2A: S6SBP401AJ0SA1001 3.325V / 0.2A: S6SBP401AM2SA1001 VOUTL2 2.800V / 0.5A RST PG1 PG2 PG3 PG4 PGL2 5 V1.1 O P E R A T I O N 2. M A N U A L Evaluation Board Specification Figure 2-1 Evaluation Board Specification Item Input Voltage S6SBP401AJ0SA1001 Output Voltage S6SBP401AM2SA1001 Output Current 6 CONFIDENTIAL Symbol Min. Typ. Max. Unit VIN 4.5 5.0 5.5 V VOUT1 - 1.250 - V VOUT2 - 1.250 - V VOUT3 - 1.850 - V VOUT4 - 3.375 - V VOUTL1 - 3.300 - V VOUTL2 - 2.800 - V VOUT1 - 1.250 - V VOUT2 - 1.125 - V VOUT3 - 2.550 - V VOUT4 - 3.375 - V VOUTL1 - 3.325 - V VOUTL2 - 2.800 - V IOUT1 - - 2.0 A IOUT2 - - 3.0 A S6SBP401AJ0SA1001 IOUT3 - - 2.0 A S6SBP401AM2SA1001 IOUT4 - - 1.0 A IOUTL1 - - 0.2 A IOUTL2 - - 0.5 A S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N 3. M A N U A L Pin Descriptions 3.1 Input/Output Descriptions Table 3-1 Input/Output Descriptions Connecter Symbol CN_VIN CN_VOUT1 CN_VOUT2 CN_VOUT3 CN_VOUT4 CN_VOUTL1 CN_VOUTL2 CN1 CN2 CN3 I/O VIN I +5V dc power supply terminal GND - Ground terminal VOUT1 O CH1 DC/DC convertor output terminal GND - Ground terminal VOUT2 O CH2 DC/DC convertor output terminal GND - Ground terminal VOUT3 O CH3 DC/DC convertor output terminal GND - Ground terminal VOUT4 O CH4 DC/DC convertor output terminal GND - Ground terminal VOUTL1 O CH1 LDO output terminal GND - Ground terminal VOUTL2 O CH2 LDO output terminal GND - Ground terminal SYNC I WDI I RST O NC - EN1, EN2, EN3, EN4 I CH1 -CH4 DC/DC convertor enable terminal External clock input terminal. Please use by referring to the data sheet of S6BP401A. Trigger input terminal of watchdog timer. Please use by referring to the data sheet of S6BP401A. Reset output terminal of watchdog timer. Please use by referring to the data sheet of S6BP401A. - ENL1, ENL2 I CH1, CH2 LDO enable terminal PG1, PG2, PG3, PG4 O CH1 -CH4 DC/DC convertor power good terminal PGL2 O CH1, CH2 LDO power good terminal VCCPullUP I Voltage supply terminal for the pull up resistors of the power good September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL Function Description 7 V1.1 O P E R A T I O N M A N U A L Figure 3-1 Pin Layout CN_VOUT1 GND VOUT1 CN_VOUT2 VOUT2 GND GND CN_VIN VOUTL1 CN_VOUTL1 VIN GND CN3 CN_VOUTL2 PG1 PG2 PG3 PG4 PGL2 VCCPullUp EN1 EN2 EN3 EN4 ENL1 ENL2 CN2 VOUTL2 NC RST WDI SYNC CN1 GND GND VOUT4 VOUT3 CN_VOUT4 8 CONFIDENTIAL GND CN_VOUT3 S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N 3.2 M A N U A L Jumper Descriptions Table 3-2 Jumper Descriptions Jumper Description Initial Setting Shorted between VIN and EN1 JP1 JP1 Short: EN1 pin is set to the H level. JP1 Open: EN1 pin is set to the L level. Input external signal to EN1 pin. Open Don’t input external signal to EN1 pin with shorted JP1. Shorted between VIN and EN2 JP2 JP2 Short: EN2 pin is set to the H level. JP2 Open: EN2 pin is set to the L level. Input external signal to EN2 pin. Open Don’t input external signal to EN2 pin with shorted JP2. Shorted between VIN and EN3 JP3 JP3 Short: EN3 pin is set to the H level. JP3 Open: EN3 pin is set to the L level. Input external signal to EN3 pin. Open Don’t input external signal to EN3 pin with shorted JP3. Shorted between VIN and EN4 JP4 JP4 Short: EN4 pin is set to the H level. JP4 Open: EN4 pin is set to the L level. Input external signal to EN4 pin. Open Don’t input external signal to EN4 pin with shorted JP4. Shorted between VIN and ENL1 JP5 JP5 Short: ENL1 pin is set to the H level. JP5 Open: ENL1 pin is set to the L level. Input external signal to ENL1 pin. Open Don’t input external signal to ENL1 pin with shorted JP5. Shorted between VIN and ENL2 JP6 JP6 Short: ENL2 pin is set to the H level. JP6 Open: ENL2 pin is set to the L level. Input external signal to ENL2 pin. Open Don’t input external signal to ENL2 pin with shorted JP6. JP7 JP8 JP9 JP14 Shorted VIN or VOUTL1 to power good pin through resistor. JP7 Short: Shorted between VOUTL1 and power good pin through resistor. JP8 Short: Shorted between VIN and power good pin through resistor. JP7 and JP8 must not be shorted simultaneously. Shorted VIN or VOUT4 to PVCCL2 of IC 37 pin. JP9 Short: Shorted between VIN and PVCCL2. JP14 Short: Shorted between VOUT4 and PVCCL2. JP9 and JP14 must not be shorted simultaneously. September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL Open Short Short Open 9 V1.1 O P E R A T I O N 4. M A N U A L Setup 4.1 Connecting 1. Connect the board to the power supply, load equipment and voltage meter as below. Figure 4-1 Connecting the Board and Some Equipment VOUT1 VOUT2 Voltage Meter + Load + Voltage Meter + Load + Voltage Meter + + +5V Power Supply VIN pin VOUTL1 Load EN1 EN2 EN3 EN4 ENL1 ENL2 + + + - - + - VOUT4 4.2 + Voltage Meter + Load - Voltage Meter - + VOUTL2 Voltage Meter - Load Enable pin Load VOUT3 Verification 1. Turn on +5V power supply. 2. Connect some enable pin to VIN, then, each DC/DC (or LDO) channel will start output. 3. Check that each output voltage is the same as the 'Output Voltage' of Figure 2-1 Evaluation Board Specification. 10 CONFIDENTIAL S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N 5. M A N U A L Layout 5.1 Component Layout Figure 5-1 Evaluation Board Component Layout Layer1 Top View Layer4 Top View Board size: 45.72mm × 30.48mm September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL 11 V1.1 O P E R A T I O N 5.2 M A N U A L Wiring Layout Figure 5-2 Evaluation Board Wiring Layout 12 CONFIDENTIAL layer 1 Top View layer 2 Top View layer 3 Top View layer 4 Top View S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N 6. M A N U A L Circuit Schematic Figure 6-1 Evaluation Board Circuit Schematic M1 30 FB1 VOUT1 VIN PVCC1 29 C35 C1 L1 LX1 28 C40 C2 C3 VOUT1 C6 PGND1 27 CN_VOUT1 VOUT1 VIN 20 FB2 VOUT2 PVCC2a 21 PVCC2b 22 C36 C7 LX2a 23 LX2b 24 PGND2a 25 PGND2b 26 L2 C41 C8 C9 CN_VOUT2 VOUT2 VIN 9 FB3 VOUT3 VOUT2 C10 C14 PVCC3 8 C37 C15 L3 LX3 7 C42 C16 VOUT3 C17 C20 PGND3 6 CN_VOUT3 VOUT3 VIN 2 FB4 VOUT4 PVCC4 3 C38 C21 L4 LX4 4 VIN C43 C22 JP6 JP5 JP4 JP3 JP2 JP1 CN2 CN_VOUT4 1 19 EN1 2 18 EN2 3 17 EN3 4 16 EN4 5 15 ENL1 6 14 ENL2 VIN VIN CN_VIN C33 34 VCC VIN PVCCL1 36 C27 LDO1 35 VOUT4 C28 VOUTL1 CN_VOUTL1 VOUTL1 JP14 PVCCL2 37 C27 LDO2 38 1 JP9 C31 VOUT4 VIN CN_VOUTL2 VOUTL2 VOUTL2 2 JP7 3 4 C34 32 VREG JP8 R10 R9 R8 R7 R6 R5 42 CP1 PG1 33 PG2 31 1 PG3 10 PG4 1 3 PGL2 40 5 39 GND EP September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CN3 2 4 44 CP3 45 CP4 VOUTL1 VIN 6 43 CP2 CONFIDENTIAL VOUT4 C23 C26 PGND4 5 SYNC 11 WDI 12 1 RST 13 3 CN1 2 4 13 V1.1 O P E R A T I O N 7. M A N U A L Component List Table 7-1 Evaluation Board Component List Rated Rated Voltage(V) Current(A) 10 µF 16 - - 22 µF 16 - - TDK 22 µF 16 - - TDK 0.1 µF 50 - - CGA5L1X7R1C106K160AC TDK 10 µF 16 - - CGA6P1X7R1C226M250AC TDK 22 µF 16 - - CGA6P1X7R1C226M250AC TDK 22 µF 16 - - C10 CGA6P1X7R1C226M250AC TDK 22 µF 16 - - C14 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 10 C15 CGA5L1X7R1C106K160AC TDK 10 µF 16 - - 11 C16 CGA6P1X7R1C226M250AC TDK 22 µF 16 - - 12 C17 CGA6P1X7R1C226M250AC TDK 22 µF 16 - - 13 C20 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 14 C21 CGA5L1X7R1C106K160AC TDK 10 µF 16 - - 15 C22 CGA6P1X7R1C226M250AC TDK 22 µF 16 - - 16 C23 CGA6P1X7R1C226M250AC TDK 22 µF 16 - - 17 C26 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 18 C27 CGA3E1X7R1C105M080AC TDK 1 µF 16 - - 19 C28 CGA3E1X7R1C105M080AC TDK 1 µF 16 - - 20 C30 CGA3E1X7R1C105M080AC TDK 1 µF 16 - - 21 C31 CGA5L1X7R1C106K160AC TDK 10 µF 16 - - 22 C33 CGA3E1X7R1C105M080AC TDK 1 µF 16 - - 23 C34 CGA3E1X7R1C105M080AC TDK 1 µF 16 - - 24 C35 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 25 C36 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 26 C37 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 27 C38 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 28 C40 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 29 C41 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 30 C42 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 31 C43 CGA2B3X7R1H104K050BB TDK 0.1 µF 50 - - 32 L1 CLF6045T-1R5N-D TDK 1.5 µH - 4.2 - 33 L2 CLF6045T-1R5N-D TDK 1.5 µH - 4.2 - 34 L3 CLF6045T-1R5N-D TDK 1.5 µH - 4.2 - 35 L4 CLF6045T-1R5N-D TDK 1.5 µH - 4.2 No. Component Parts Number Vendor Value 1 2 C1 CGA5L1X7R1C106K160AC TDK C2 CGA6P1X7R1C226M250AC TDK 3 C3 CGA6P1X7R1C226M250AC 4 C6 CGA2B3X7R1H104K050BB 5 C7 6 C8 7 C9 8 9 36 M1 37 R5 38 S6BP401AJ0SN1B000 Remarks S6SBP401AJ0SA1001 Cypress - - - RG1608P-473-B SSM 47 kΩ - - - R6 RG1608P-473-B SSM 47 kΩ - - - 39 R7 RG1608P-473-B SSM 47 kΩ - - - 40 R8 RG1608P-473-B SSM 47 kΩ - - - 41 R9 RG1608P-473-B SSM 47 kΩ - - - 42 R10 RG1608P-473-B SSM 47 kΩ - - - 14 CONFIDENTIAL S6BP401AM2SN1B000 S6SBP401AM2SA1001 S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N M A N U A L TDK : TDK Corporation Cypress : Cypress Semiconductor Corp SSM : SUSUMU CO., LTD. NMT: No mount. These components are compliant with RoHS, and please ask each vendor for details if necessary. September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL 15 V1.1 O P E R A T I O N 8. M A N U A L Ordering Information Table 8-1 Ordering Information 9. Part Number EVB Revision Note S6SBP401AJ0SA1001 S6SBP401A-SA1 Mounted IC: S6BP401AJ0SN1B000 S6SBP401AM2SA1001 Rev 2.0 Mounted IC: S6BP401AM2SN1B000 Major Changes Table 9-1 Major Changes Page Section Change Results Revision 1.0 - 16 CONFIDENTIAL - Initial release S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1 O P E R A T I O N M A N U A L SS901-00045-1v0-E Cypress Support Tool Manual S6SBP401AJ0SA1001, S6SBP401AM2SA1001 Evaluation Kit for Automotive PMIC Operation Manual September 2015 Rev. 1.0 Published: Edited: Cypress Semiconductor Corp. Communications September 11, 2015, S6SBP401AJ0SA1001_SS901-00045-1v0-E CONFIDENTIAL 17 V1.1 O P E R A T I O N M A N U A L Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Cypress will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Cypress product under development by Cypress. Cypress reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Cypress assumes no liability for any damages of any kind arising out of the use of the information in this document. ® Copyright © 2015 Cypress Semiconductor Corp. All rights reserved. Cypress, the Cypress logo, Spansion , the Spansion ® ® TM TM TM TM logo, MirrorBit , MirrorBit Eclipse , ORNAND , Easy DesignSim , Traveo and combinations thereof, are trademarks and registered trademarks of Cypress Semiconductor Corp. in the United States and other countries. Other names used are for informational purposes only and may be trademarks of their respective owners. 18 CONFIDENTIAL S6SBP401AJ0SA1001_SS901-00045-1v0-E, September 11, 2015 v1.1